Mechanical properties of highly porous PDLLA/Bioglass composite foams as scaffolds for bone tissue engineering

Study of Damage Prediction of Carbon Fiber Tows Using Eddy Current Measurement

When manufacturing fiber-reinforced composites, it is possible to improve the quality of fiber steel fire and reduce the number of cracks in the finished product if it is possible to quickly identify the defects of the fiber tow. Therefore, in this study, we developed a method to identify the condition of carbon fiber tow using eddy current test (ECT), which is used to improve the quality of composite materials. Using the eddy current detection sensor, we checked the impedance results according to the condition of the CF tow. We found that the materials of the workbench used in the experiment greatly affected the ECT results, so it is necessary to use a material with a non-conductive and smooth surface. We evaluated the impedance results of the carbon fiber at 2 mm intervals using the ECT sensor and summarized the impedance results according to the fiber width direction, presenting the condition of the section as a constant of variation (CV). If the condition of the carbon fiber tow was unstable, the deviation of the CV per section was large. In particular, the deviation of the CV per section was more than 0.15 when the arrangement of the fibers was changed, foreign substances were formed on the surface of the fibers, and damage occurred in the direction of the fiber width of more than 4 mm, so it was easy to evaluate the quality on CF tow.

Bioactive Materials for Bone Regeneration: Biomolecules and Delivery Systems

Novel tissue regeneration strategies are constantly being developed worldwide. Research on bone regeneration is noteworthy, as many promising new approaches have been documented with novel strategies currently under investigation. Innovative biomaterials that allow the coordinated and well-controlled repair of bone fractures and bone loss are being designed to reduce the need for autologous or allogeneic bone grafts eventually. The current engineering technologies permit the construction of synthetic, complex, biomimetic biomaterials with properties nearly as good as those of natural bone with good biocompatibility. To ensure that all these requirements meet, bioactive molecules are coupled to structural scaffolding constituents to form a final product with the desired physical, chemical, and biological properties. Bioactive molecules that have been used to promote bone regeneration include protein growth factors, peptides, amino acids, hormones, lipids, and flavonoids. Various strategies have been adapted to investigate the coupling of bioactive molecules with scaffolding materials to sustain activity and allow controlled release. The current manuscript is a thorough survey of the strategies that have been exploited for the delivery of biomolecules for bone regeneration purposes, from choosing the bioactive molecule to selecting the optimal strategy to synthesize the scaffold and assessing the advantages and disadvantages of various delivery strategies.

A self-assembled dynamic extracellular matrix-like hydrogel system with multi-scale structures for cell bioengineering applications

Extracellular matrix (ECM) provides various types of direct interactions with cells and a dynamic environment, which can be remodeled through different assembly/degradation mechanisms to adapt to different biological processes. Herein, through introducing polyphosphate-modified hyaluronic acid and bioactive glass (BG) nano-fibril into a self-assembled hydrogel system with peptide-polymer conjugate, we can realize many new ECM-like functions in a synthetic polymer network. The hydrogel network formation is mediated by coacervation, followed by a gradual transition of peptide structure from  α-helix to β-sheet. The ECM-like hydrogels can be degraded through a number of orthogonal mechanisms, including treatments with protease, hyaluronidase, alkaline phosphatase, and calcium ion. As 2D coating, the ECM-like hydrogels can be used to modify the planar surface to promote the adhesion of mesenchymal stromal cells, or to coat the cell surface in a layer-by-layer fashion to shield the interaction with the substrate. As ECM-like hydrogels for 3D cell culture, the system is compatible with injection and cell encapsulation. Upon incorporating fragmented electrospun bioactive glass nano-fibril into the hydrogels, the synergetic effects of soft hydrogel and stiff reinforcement nanofibers on recapitulating ECM functions result in reduced cell circularity in 3D. Finally, by injecting the ECM-like hydrogels into mice, gradual degradations over a time period of one month and high biocompatibility have been shown in vivo. The contribution of complex network dynamics and hierarchical structures to cell-biomatrix interaction can be investigated multi-dimensionally, as many mechanisms are orthogonal to each other and can be regulated individually. STATEMENT OF SIGNIFICANCE: A list of native ECM features has attracted the most interest and attention in the research of synthetic biomaterials. In this research, we have described a simple ECM-like hydrogel system in which the complex and elegant functions of native ECM can be recapitulated in a chemically defined synthetic system. The ECM-like hydrogel systems were developed to avoid undesired features of biological substances (e.g., ethical concerns, batch-to-batch variation, immunogenicity, and potential risk of contamination), as well as gaining new functions to facilitate bioengineering applications (e.g., 3D cell culture, injection, and high stability). To this end, we have developed an ECM-like hydrogel system and provide evidence that this purely synthetic biomaterial is a promising candidate for cell bioengineering applications.

Temperature and Infill Density Effects on Thermal, Mechanical and Shape Memory Properties of Polylactic Acid/Poly(ε-caprolactone) Blends for 4D Printing

Polylactic acid (PLA)/poly(ε-caprolactone) (PCL) blends have exhibited good shape memory properties and degradable characteristics in various 4D printing fields such as biomedicine, flexible electronics, and soft robotics, where the service temperature fluctuates easily by environment temperature and polymer characteristics. In this work, printed PLA/PCL 4D samples with different infill densities were prepared by material extrusion printing of pre-extruded filaments and characterized under different temperatures. The results show that the microstructures of printed samples are not influenced by printing process and have similar unique orientation as that of filaments. The thermal properties are stable and show obvious phase transition temperatures, while the mechanical properties decrease slightly in low temperature region and then decrease rapidly when temperature is over 60 °C. The increase in infill density can further improve the storage modulus more than 40% and have no significant influence on the thermal properties. The printed samples also exhibit good shape memory performances with fast recovery speeds less than 22 s. Furthermore, a two-step model is provided to predict the effective modulus of printed PLA/PCL samples and agrees well with experimental data. The results prove that temperature and infill density have different influences on the thermal, mechanical and shape memory properties of PLA/PCL blends.

A Self-Assembled Matrix System for Cell-Bioengineering Applications in Different Dimensions, Scales, and Geometries

Stem cell bioengineering and therapy require different model systems and materials in different stages of development. If a chemically defined biomatrix system can fulfill most tasks, it can minimize the discrepancy among various setups. By screening biomaterials synthesized through a coacervation-mediated self-assembling mechanism, a biomatrix system optimal for 2D human mesenchymal stromal cell (hMSC) culture and osteogenesis is identified. Its utility for hMSC bioengineering is further demonstrated in coating porous bioactive glass scaffolds and nanoparticle synthesis for esiRNA delivery to knock down the SOX-9 gene with high delivery efficiency. The self-assembled injectable system is further utilized for 3D cell culture, segregated co-culture of hMSC with human umbilical vein endothelial cells (HUVEC) as an angiogenesis model, and 3D bioprinting. Most interestingly, the coating of bioactive glass with the self-assembled biomatrix not only supports the proliferation and osteogenesis of hMSC in the 3D scaffold but also induces the amorphous bioactive glass (BG) scaffold surface to form new apatite crystals resembling bone-shaped plate structures. Thus, the self-assembled biomatrix system can be utilized in various dimensions, scales, and geometries for many different bioengineering applications.

A Review on the Modeling of the Elastic Modulus and Yield Stress of Polymers and Polymer Nanocomposites: Effect of Temperature, Loading Rate and Porosity

Porous polymer-based nanocomposites have been used for various applications due to their advantages, including multi-functionalities, easy and known manufacturability, and low cost. Understanding of their mechanical properties has become essential to expand the nanocomposites’ applications and efficiency, including service-life, resistance to different loads, and reliability. In this review paper, the focus is on the modeling of the mechanical properties of porous polymer-based nanocomposites, including the effects of loading rates, operational temperatures, and the material’s porosity. First, modeling of the elastic modulus and yield stress for glassy polymers and polymer reinforced by nanofillers are addressed. Then, modeling of porosity effects on these properties for polymers are reviewed, especially via the use of the well-known power-law approach linking porosity to elastic modulus and/or stress. Studies related to extending the mechanical modeling to account for porosity effects on the elastic modulus and yield stress of polymers and polymer-nanocomposites are discussed. Finally, a brief review of the implementation of this modeling into 3D computational methods to predict the large elastic-viscoplastic deformation response of glassy polymers is presented. In addition to the modeling part, the experimental techniques to measure the elastic modulus and the yield stress are discussed, and applications of polymers and polymer composites as membranes for water treatment and scaffolds for bone tissue engineering are addressed. Some modeling results and validation from different studies are presented as well.

Highly porous novel chondro-instructive bioactive glass scaffolds tailored for cartilage tissue engineering

Cartilage injuries remain challenging since the regenerative capacity of cartilage is extremely low. The aim was to design a novel type of bioactive glass (BG) scaffold with suitable topology that allows the formation of cartilage-specific extracellular matrix (ECM) after colonization with chondrogenic cells for cartilage repair. Highly porous scaffolds with interconnecting pores consisting of 100 % BG were manufactured using a melting, milling, sintering and leaching technique. Scaffolds were colonized with porcine articular chondrocytes (pAC) and undifferentiated human mesenchymal stromal cells (hMSC) for up to 35 days. Scaffolds displayed high cytocompatibility with no major pH shift. Scanning electron microscopy revealed the intimate pAC-scaffold interaction with typical cell morphology. After 14 days MSCs formed cell clusters but still expressed cartilage markers. Both cell types showed aggrecan, SOX9 gene and protein expression, cartilage proteoglycan and sulfated glycosaminoglycan synthesis for the whole culture time. Despite type II collagen gene expression could not anymore be detected at day 35, protein synthesis was visualized for both cell types during the whole culturing period, increasing in pAC and declining after day 14 in hMSC cultures. The novel BG scaffold was stable, cytocompatible and cartilage-specific protein synthesis indicated maintenance of pAC's differentiated phenotype and chondro-instructive effects on hMSCs.

Biomaterials and osteoradionecrosis of the jaw: Review of the literature according to the SWiM methodology

OBJECTIVES

To systematically present and interpret the current literature on research and treatment perspectives for mandibular osteoradionecrosis (mORN) in the field of biomaterials.

MATERIAL AND METHODS

A systematic review of the literature using the "Synthesis without meta-analysis" (SWiM) methodology was performed on PubMed, Embase and Cochrane, focusing on the implantation of synthetic biomaterials for bone reconstruction in mORN in humans and/or animal models. The primary endpoints were the composition, efficacy on mORN and tolerance of the implanted synthetic biomaterials.

RESULTS

Forty-seven references were obtained and evaluated in full-text by two assessors. Ten (8 in humans and 2 in animal models) met the eligibility criteria and were included for analysis. Materials most often comprised support plates or metal mesh (5 of 10 cases) in combination with grafts or synthetic materials (phosphocalcic ceramics, glutaraldehyde). Other ceramic/polymer composites were also implanted. In half of the selected reports, active compounds (molecules, growth factors, lysates) and/or cells were associated with the reconstruction material. The number of articles referring to implantation of biomaterials for the treatment of mORN was small, and the properties of the implanted biomaterials were generally poorly described, thus limiting a thorough understanding of their role.

CONCLUSION

In preventing the morbidity associated with some reconstructive surgeries, basic research has benefitted from recent advances in tissue engineering and biomaterials to repair limited bone loss.

Functionally Graded Scaffolds with Programmable Pore Size Distribution Based on Triply Periodic Minimal Surface Fabricated by Selective Laser Melting

Functional graded materials are gaining increasing attention in tissue engineering (TE) due to their superior mechanical properties and high biocompatibility. Triply periodic minimal surface (TPMS) has the capability to produce smooth surfaces and interconnectivity, which are very essential for bone scaffolds. To further enhance the versatility of TPMS, a parametric design method for functionally graded scaffold (FGS) with programmable pore size distribution is proposed in this study. Combining the relative density and unit cell size, the effect of design parameters on the pore size was also considered to effectively govern the distribution of pores in generating FGS. We made use of Gyroid to generate different types of FGS, which were then fabricated using selective laser melting (SLM), followed by investigation and comparison of their structural characteristics and mechanical properties. Their morphological features could be effectively controlled, indicating that TPMS was an effective way to achieve functional gradients which had bone-mimicking architectures. In terms of mechanical performance, the proposed FGS could achieve similar mechanical response under compression tests compared to the reference FGS with the same range of density gradient. The proposed method with control over pore size allows for effectively generating porous scaffolds with tailored properties which are potentially adopted in various fields.

Synthesis and characterization of collagen/calcium phosphate scaffolds incorporating antibacterial agent for bone tissue engineering application

In the present study, we developed a novel niosomal nanocarrier embedded into a collagen/β- tricalcium phosphate (Col/β-TCP) scaffold for the local delivery of thymol as a natural anti-bacterial reagent. The niosomal Col/β-TCP (N-Col/β-TCP) scaffolds with different weight ratios of β-TCP to Col were prepared by freeze-drying. The antimicrobial activities of the prepared samples against Escherichia coli, Pseudomonas aeruginosa, and Staphylococcus aureus were assessed by agar diffusion method. The release profile of niosomal thymol from the optimized composite scaffolds showed a sustained profile where 66% of the loaded thymol was released over 30 days. The compressive modulus of niosome added scaffolds with an equal ratio of β-TCP and Col was calculated as 972±1.3KPa. This scaffold showed significantly higher values of cell viability (as evaluated by an MTT assay) against L929 fibroblasts than a scaffold without niosomal thymol after 24 and 72 h. Among synthesized samples, Col/β-TCP1 showed the greatest effectiveness of anti-bacterial activity toward Gram-positive and Gram-negative bacteria with higher activity against Gram-positive ones. The results of this study highlight the potential of niosomal-thymol loaded Col/β-TCP1 scaffold as an anti-bacterial bone substitute for possible osteomyelitis treatment.

Effect of Cu- and Zn-Doped Bioactive Glasses on the In Vitro Bioactivity, Mechanical and Degradation Behavior of Biodegradable PDLLA Scaffolds

Biodegradable polymer scaffolds filled with bioactive glass particles doped with therapeutic metal ions are a novel and promising strategy to repair critical-sized bone defects. In this study, scaffolds based on a poly (D, L-lactide acid) (PDLLA) matrix filled with un-doped and Cu-, Zn- and CuZn-doped bioactive glass particles were produced by freeze-drying and a salt-leaching method. The effects of the doping and content of the glass particles (10 and 30 wt.%) on the morphology, compression properties, apatite formation, and degradation behavior of the scaffolds were evaluated. The scaffolds presented high porosity (~93%) with pores ranged from 100 to 400 μm interconnected by smaller pores and this porosity was kept after the glass particles incorporation. The glass particles reinforced the polymer scaffolds with improvements as high as 130% in elastic moduli, and further promoted the apatite formation on the scaffold surface, both properties depending on the amount and type of filler. The bioactive glass particles boosted the scaffold degradation with the PDLLA/un-doped glass scaffold showing the highest rate, but still retaining structural and dimensional integrity. Our findings show that the incorporation of un-doped and metal-doped bioactive glasses increases the mechanical strength, promotes the bioactivity and modifies the degradation profile of the resulting polymer/glass scaffolds, making them better candidates for bone repair.

Poly(d,l-Lactic acid) Composite Foams Containing Phosphate Glass Particles Produced via Solid-State Foaming Using CO2 for Bone Tissue Engineering Applications

This study reports on the production and characterization of highly porous (up to 91%) composite foams for potential bone tissue engineering (BTE) applications. A calcium phosphate-based glass particulate (PGP) filler of the formulation 50P₂O₅-40CaO-10TiO₂ mol.%, was incorporated into biodegradable poly(d,l-lactic acid) (PDLLA) at 5, 10, 20, and 30 vol.%. The composites were fabricated by melt compounding (extrusion) and compression molding, and converted into porous structures through solid-state foaming (SSF) using high-pressure gaseous carbon dioxide. The morphological and mechanical properties of neat PDLLA and composites in both nonporous and porous states were examined. Scanning electron microscopy micrographs showed that the PGPs were well dispersed throughout the matrices. The highly porous composite systems exhibited improved compressive strength and Young’s modulus (up to >2-fold) and well-interconnected macropores (up to ~78% open pores at 30 vol.% PGP) compared to those of the neat PDLLA foam. The pore size of the composite foams decreased with increasing PGPs content from an average of 920 µm for neat PDLLA foam to 190 µm for PDLLA-30PGP. Furthermore, the experimental data was in line with the Gibson and Ashby model, and effective microstructural changes were confirmed to occur upon 30 vol.% PGP incorporation. Interestingly, the SSF technique allowed for a high incorporation of bioactive particles (up to 30 vol.%—equivalent to ~46 wt.%) while maintaining the morphological and mechanical criteria required for BTE scaffolds. Based on the results, the SSF technique can offer more advantages and flexibility for designing composite foams with tunable characteristics compared to other methods used for the fabrication of BTE scaffolds.

Bone Repair and Regenerative Biomaterials: Towards Recapitulating the Microenvironment

Biomaterials and tissue engineering scaffolds play a central role to repair bone defects. Although ceramic derivatives have been historically used to repair bone, hybrid materials have emerged as viable alternatives. The rationale for hybrid bone biomaterials is to recapitulate the native bone composition to which these materials are intended to replace. In addition to the mechanical and dimensional stability, bone repair scaffolds are needed to provide suitable microenvironments for cells. Therefore, scaffolds serve more than a mere structural template suggesting a need for better and interactive biomaterials. In this review article, we aim to provide a summary of the current materials used in bone tissue engineering. Due to the ever-increasing scientific publications on this topic, this review cannot be exhaustive; however, we attempted to provide readers with the latest advance without being redundant. Furthermore, every attempt is made to ensure that seminal works and significant research findings are included, with minimal bias. After a concise review of crystalline calcium phosphates and non-crystalline bioactive glasses, the remaining sections of the manuscript are focused on organic-inorganic hybrid materials.

Human nasoseptal chondrocytes maintain their differentiated phenotype on PLLA scaffolds produced by thermally induced phase separation and supplemented with bioactive glass 1393

Damage of hyaline cartilage such as nasoseptal cartilage requires proper reconstruction, which remains challenging due to its low intrinsic repair capacity. Implantation of autologous chondrocytes in combination with a biomimetic biomaterial represents a promising strategy to support cartilage repair. Despite so far mostly tested for bone tissue engineering, bioactive glass (BG) could exert stimulatory effects on chondrogenesis. The aim of this work was to produce and characterize composite porous poly(L-lactide) (PLLA)/1393BG scaffolds via thermally induced phase separation (TIPS) technique and assess their effects on chondrogenesis of nasoseptal chondrocytes. The PLLA scaffolds without or with 1, 2.5, 5% BG1393 were prepared via TIPS technique starting from a ternary solution (polymer/solvent/non-solvent) in a single step. Scaffolds were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and differential scanning calorimetric analysis (DSC). Human nasoseptal chondrocytes were seeded on the scaffolds with 1 and 2.5% BG for 7 and 14 days and cell survival, attachment, morphology and expression of SOX9 and cartilage-specific extracellular cartilage matrix (ECM) components were monitored. The majority of chondrocytes survived on all PLLA scaffolds functionalized with BG for the whole culture period. Also inner parts of the scaffold were colonized by chondrocytes synthesizing an ECM which contained glycosaminoglycans. Type II collagen and aggrecan gene expression increased significantly in 1% BG scaffolds during the culture. Chondrocyte protein expression for cartilage ECM proteins indicated that the chondrocytes maintained their differentiated phenotype in the scaffolds. BG could serve as a cytocompatible basis for future scaffold composites for osteochondral cartilage defect repair. Abbreviations: AB: alcian blue ACAN: gene coding for aggrecan; BG: Bioactive glass; 2D: two-dimensional; 3D: three-dimensional; COL2A1: gene coding for type II collagen; DAPI: 4',6-diamidino-2-phenylindole; DMEM: Dulbecco's Modified Eagle's Medium; DMMB: dimethylmethylene blue; DSC: Differential scanning calorimetric analysis; ECM: extracellular matrix; EDTA: ethylenediaminetetraacetic acid; EtBr: ethidium bromide; FCS: fetal calf serum; FDA: fluorescein diacetate; GAG: glycosaminoglycans; HDPE: high density polyethylene; HE: hematoxylin and eosin staining; HCA: hydoxylapatite; PBE: phosphate buffered EDTA100 mM Na₂HPO₄ and 5 mM EDTA, pH8; PBS: phosphate buffered saline; PFA: paraformaldehyde; PG: proteoglycans; PI: propidium iodide; PLLA: Poly-L-Lactic Acid Scaffold; RT: room temperature; SD: standard deviation; SEM: scanning electron microscopy; sGAG: sulfated glycosaminoglycans; SOX9/Sox9: SRY (sex-determining region Y)-box 9 protein; TBS: TRIS buffered saline; TIPS: Thermally Induced Phase Separation; XRD: X-ray diffraction analysis.

Optimized Bioactive Glass: the Quest for the Bony Graft

Technological advances have provided surgeons with a wide range of biomaterials. Yet improvements are still to be made, especially for large bone defect treatment. Biomaterial scaffolds represent a promising alternative to autologous bone grafts but in spite of the numerous studies carried out on this subject, no biomaterial scaffold is yet completely satisfying. Bioactive glass (BAG) presents many qualifying characteristics but they are brittle and their combination with a plastic polymer appears essential to overcome this drawback. Recent advances have allowed the synthesis of organic-inorganic hybrid scaffolds combining the osteogenic properties of BAG and the plastic characteristics of polymers. Such biomaterials can now be obtained at room temperature allowing organic doping of the glass/polymer network for a homogeneous delivery of the doping agent. Despite these new avenues, further studies are required to highlight the biological properties of these materials and particularly their behavior once implanted in vivo. This review focuses on BAG with a particular interest in their combination with polymers to form organic-inorganic hybrids for the design of innovative graft strategies.

Fabrication and mechanical characterization of 3D printed vertical uniform and gradient scaffolds for bone and osteochondral tissue engineering

Recent developments in 3D printing (3DP) research have led to a variety of scaffold designs and techniques for osteochondral tissue engineering; however, the simultaneous incorporation of multiple types of gradients within the same construct remains a challenge. Herein, we describe the fabrication and mechanical characterization of porous poly(ε-caprolactone) (PCL) and PCL-hydroxyapatite (HA) scaffolds with incorporated vertical porosity and ceramic content gradients via a multimaterial extrusion 3DP system. Scaffolds of 0 wt% HA (PCL), 15 wt% HA (HA15), or 30 wt% HA (HA30) were fabricated with uniform composition and porosity (using 0.2 mm, 0.5 mm, or 0.9 mm on-center fiber spacing), uniform composition and gradient porosity, and gradient composition (PCL-HA15-HA30) and porosity. Micro-CT imaging and porosity analysis demonstrated the ability to incorporate both vertical porosity and pore size gradients and a ceramic gradient, which collectively recapitulate gradients found in native osteochondral tissues. Uniaxial compression testing demonstrated an inverse relationship between porosity, ϕ, and compressive modulus, E, and yield stress, σy, for uniform porosity scaffolds, however, no differences were observed as a result of ceramic incorporation. All scaffolds demonstrated compressive moduli within the appropriate range for trabecular bone, with average moduli between 86 ± 14-220 ± 26 MPa. Uniform porosity and pore size scaffolds for all ceramic levels had compressive moduli between 205 ± 37-220 ± 26 MPa, 112 ± 13-118 ± 23 MPa, and 86 ± 14-97 ± 8 MPa respectively for porosities ranging between 14 ± 4-20 ± 6%, 36 ± 3-43 ± 4%, and 54 ± 2-57 ± 2%, with the moduli and yield stresses of low porosity scaffolds being significantly greater (p < 0.05) than those of all other groups. Single (porosity) gradient and dual (composition/porosity) gradient scaffolds demonstrated compressive properties similar (p > 0.05) to those of the highest porosity uniform scaffolds (porosity gradient scaffolds 98 ± 23-107 ± 6 MPa, and 102 ± 7 MPa for dual composition/porosity gradient scaffolds), indicating that these properties are more heavily influenced by the weakest section of the gradient. The compression data for uniform scaffolds were also readily modeled, yielding scaling laws of the form E ∼ (1 - ϕ)1.27 and σy ∼ (1 - ϕ)1.37, which demonstrated that the compressive properties evaluated in this study were well-aligned with expectations from previous literature and were readily modeled with good fidelity independent of polymer scaffold geometry and ceramic content. All uniform scaffolds were similarly deformed and recovered despite different porosities, while the large-pore sections of porosity gradient scaffolds were significantly more deformed than all other groups, indicating that porosity may not be an independent factor in determining strain recovery. Moving forward, the technique described here will serve as the template for more complex multimaterial constructs with bioactive cues that better match native tissue physiology and promote tissue regeneration. STATEMENT OF SIGNIFICANCE: This manuscript describes the fabrication and mechanical characterization of "dual" porosity/ceramic content gradient scaffolds produced via a multimaterial extrusion 3D printing system for osteochondral tissue engineering. Such scaffolds are designed to better address the simultaneous gradients in architecture and mineralization found in native osteochondral tissue. The results of this study demonstrate that this technique may serve as a template for future advances in 3D printing technology that may better address the inherent complexity in such heterogeneous tissues.

Development of 3D-printed PLGA/TiO2 nanocomposite scaffolds for bone tissue engineering applications

Porous scaffolds were 3D-printed using poly lactic-co-glycolic acid (PLGA)/TiO2 composite (10:1 weight ratio) for bone tissue engineering applications. Addition of TiO2 nanoparticles improved the compressive modulus of scaffolds. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) revealed an increase in both glass transition temperature and thermal decomposition onset of the composite compared to pure PLGA. Furthermore, addition of TiO2 was found to enhance the wettability of the surface evidenced by reducing the contact angle from 90.5 ± 3.2 to 79.8 ± 2.4 which is in favor of cellular attachment and activity. The obtained results revealed that PLGA/TiO2 scaffolds significantly improved osteoblast proliferation compared to pure PLGA (p < 0.05). Furthermore, osteoblasts cultured on PLGA/TiO2 nanocomposite showed significantly higher ALP activity and improved calcium secretion compared to pure PLGA scaffolds (p < 0.05).

Enzymatically Cross-Linked Silk Fibroin-Based Hierarchical Scaffolds for Osteochondral Regeneration

Osteochondral (OC) regeneration faces several limitations in orthopedic surgery, owing to the complexity of the OC tissue that simultaneously entails the restoration of articular cartilage and subchondral bone diseases. In this study, novel biofunctional hierarchical scaffolds composed of a horseradish peroxidase (HRP)-cross-linked silk fibroin (SF) cartilage-like layer (HRP-SF layer) fully integrated into a HRP-SF/ZnSr-doped β-tricalcium phosphate (β-TCP) subchondral bone-like layer (HRP-SF/dTCP layer) were proposed as a promising strategy for OC tissue regeneration. For comparative purposes, a similar bilayered structure produced with no ion incorporation (HRP-SF/TCP layer) was used. A homogeneous porosity distribution was achieved throughout the scaffolds, as shown by micro-computed tomography analysis. The ion-doped bilayered scaffolds presented a wet compressive modulus (226.56 ± 60.34 kPa) and dynamic mechanical properties (ranging from 403.56 ± 111.62 to 593.56 ± 206.90 kPa) superior to that of the control bilayered scaffolds (189.18 ± 90.80 kPa and ranging from 262.72 ± 59.92 to 347.68 ± 93.37 kPa, respectively). Apatite crystal formation, after immersion in simulated body fluid (SBF), was observed in the subchondral bone-like layers for the scaffolds incorporating TCP powders. Human osteoblasts (hOBs) and human articular chondrocytes (hACs) were co-cultured onto the bilayered structures and monocultured in the respective cartilage and subchondral bone half of the partitioned scaffolds. Both cell types showed good adhesion and proliferation in the scaffold compartments, as well as adequate integration of the interface regions. Osteoblasts produced a mineralized extracellular matrix (ECM) in the subchondral bone-like layers, and chondrocytes showed GAG deposition. The gene expression profile was different in the distinct zones of the bilayered constructs, and the intermediate regions showed pre-hypertrophic chondrocyte gene expression, especially on the BdTCP constructs. Immunofluorescence analysis supported these observations. This study showed that the proposed bilayered scaffolds allowed a specific stimulation of the chondrogenic and osteogenic cells in the co-culture system together with the formation of an osteochondral-like tissue interface. Hence, the structural adaptability, suitable mechanical properties, and biological performance of the hierarchical scaffolds make these constructs a desired strategy for OC defect regeneration.

Preparation of gelatin hydrogel sponges incorporating bioactive glasses capable for the controlled release of fibroblast growth factor-2

Gelatin hydrogel sponges incorporating bioactive glasses (Gel-BG) were fabricated. We evaluated the characteristics of Gel-BG as scaffolds from the perspective of their mechanical properties and the formation of hydroxyapatite by the incorporation of bioactive glasses (BG). In addition, the Gel-BG degradation and the profile of fibroblast growth factor-2 (FGF-2) release from the Gel-BG were examined. Every Gel-BG showed an interconnected pore structure with the pore size range of 180-200 µm. The compression modulus of sponges incorporating BG increased. The time profiles of degradation for the 72-h crosslinked gelatin hydrogel sponges incorporating 10 wt% BG (Gel-BG(10)) and 50 wt% BG (Gel-BG(50)) were analogous to that of the 24-h crosslinked gelatin hydrogel sponge without BG (Gel-BG(0)). In measuring the release of FGF-2 from Gel-BG, the Gel-BG(10) and Gel-BG(50) showed almost analogous 100% cumulative release within 28 days in vivo. Additionally, a bioactivity evaluation showed that the presence of gelatin does not affect the in vitro bioactivity of Gel-BG. These sponges showed mechanical and chemical functionality as scaffolds, featuring both the controlled release of FGF-2 and the induction of hydroxyapatite crystallization.

Ice-Templated Porous Nanocellulose-Based Materials: Current Progress and Opportunities for Materials Engineering

Nanocelluloses (cellulose nanocrystals, CNCs, or cellulose nanofibrils, CNFs) are the elementary reinforcing constituents of plant cell walls. Because of their pronounced slenderness and outstanding intrinsic mechanical properties, nanocelluloses constitute promising building blocks for the design of future biobased high-performance materials such as nanocomposites, dense and transparent films, continuous filaments, and aerogels and foams. The research interest in nanocellulose-based aerogels and foams is recent but growing rapidly. These materials have great potential in many engineering fields, including construction, transportation, energy, and biomedical sectors. Among the various processing routes used to obtain these materials, ice-templating is one of the most regarded, owing to its simplicity and versatility and the wide variety of porous materials that this technique can provide. The focus of this review is to discuss the current state of the art and understanding of ice-templated porous nanocellulose-based materials. We provide a review of the main forming processes that use the principle of ice-templating to produce porous nanocellulose-based materials and discuss the effect of processing conditions and suspension formulation on the resulting microstructures of the materials.

Structure and performance properties of environmentally-friendly biocomposites based on poly(ɛ-caprolactone) modified with copper slag and shale drill cuttings wastes

The potential application of two types of industrial wastes, drill cuttings (DC) and copper slag (CS), as silica-rich modifiers of poly(ɛ-caprolactone) (PCL) was investigated. Chemical structure and physical properties of DC and CS fillers were characterized using X-ray diffractometer, X-ray fluorescence spectroscopy, particle size and density measurements. PCL/DC and PCL/CS composites with a variable content of filler (5 to 50 parts by weight) were prepared by melt compounding in an internal mixer. It was observed that lower particle size of DC filler enhanced processing of biocomposites comparing to CS filler. Smaller particles of DC filler and thus the higher specific surface area, enabled better encapsulation of filler by polymer chains, hence lower porosity and consequently higher tensile properties comparing to PCL/CS biocomposites. It was noticed, that the impact of waste filler characteristics on tensile properties became negligible at higher loadings. This indicates weak interactions between waste filler and PCL matrix, due to aggregation of filler particles and formulation of voids in phase boundary. This phenomenon was confirmed by scanning electron microscopy, headspace analysis and thermogravimetric analysis. Microbial tests revealed that prepared biocomposites show no toxic effect towards analyzed bacterial strains, therefore could be considered as environmentally-friendly.

Biomimetic delivery of signals for bone tissue engineering

Bone tissue engineering is an exciting approach to directly repair bone defects or engineer bone tissue for transplantation. Biomaterials play a pivotal role in providing a template and extracellular environment to support regenerative cells and promote tissue regeneration. A variety of signaling cues have been identified to regulate cellular activity, tissue development, and the healing process. Numerous studies and trials have shown the promise of tissue engineering, but successful translations of bone tissue engineering research into clinical applications have been limited, due in part to a lack of optimal delivery systems for these signals. Biomedical engineers are therefore highly motivated to develop biomimetic drug delivery systems, which benefit from mimicking signaling molecule release or presentation by the native extracellular matrix during development or the natural healing process. Engineered biomimetic drug delivery systems aim to provide control over the location, timing, and release kinetics of the signal molecules according to the drug's physiochemical properties and specific biological mechanisms. This article reviews biomimetic strategies in signaling delivery for bone tissue engineering, with a focus on delivery systems rather than specific molecules. Both fundamental considerations and specific design strategies are discussed with examples of recent research progress, demonstrating the significance and potential of biomimetic delivery systems for bone tissue engineering.

On-Demand Microwave-Assisted Fabrication of Gelatin Foams

Ultraporous gelatin foams (porosity >94%, ρ ≈ 0.039–0.056 g/cm³) have been fabricated via microwave radiation. The resulting foam structures are unique with regard to pore morphology (i.e., closed-cell) and exhibit 100% macroporosity (pore size 332 to 1700 μm), presence of an external skin, and densities similar to aerogels. Results indicate that the primary foaming mechanism is governed by the vaporization of water that is tightly bound in secondary structures (i.e., helices, β-turns, β-sheets) that are present in dehydrated gelatin films but not present in the foams after microwave radiation (700 Watts).

Biocompatible Nanobioglass Reinforced Poly(ε-Caprolactone) Composites Synthesized via In Situ Ring Opening Polymerization

Poly(ε-caprolactone) (PCL) is a bioresorbable synthetic polyester widely studied as a biomaterial for tissue engineering and controlled release applications, but its low bioactivity and weak mechanical performance limits its applications. In this work, nanosized bioglasses with two different compositions (SiO₂–CaO and SiO₂–CaO–P₂O₅) were synthesized with a hydrothermal method, and each one was used as filler in the preparation of PCL nanocomposites via the in situ ring opening polymerization of ε-caprolactone. The effect of the addition of 0.5, 1 and 2.5 wt % of the nanofillers on the molecular weight, structural, mechanical and thermal properties of the polymer nanocomposites, as well as on their enzymatic hydrolysis rate, bioactivity and biocompatibility was systematically investigated. All nanocomposites exhibited higher molecular weight values in comparison with neat PCL, and mechanical properties were enhanced for the 0.5 and 1 wt % filler content, which was attributed to extensive interactions between the filler and the matrix, proving the superiority of in situ polymerization over solution mixing and melt compounding. Both bioglasses accelerated the enzymatic degradation of PCL and induced bioactivity, since apatite was formed on the surface of the nanocomposites after soaking in simulated body fluid. Finally, all samples were biocompatible as Wharton jelly-derived mesenchymal stem cells (WJ-MSCs) attached and proliferated on their surfaces.

Cell proliferation influenced by matrix compliance of gelatin grafted poly(d,l-Lactide) three dimensional scaffolds

Surface and mechanical properties of the biomaterials are determinants of cellular responses. In our previous study, star-shaped poly(d,l-Lactide)-b-gelatin (ss-pLG) was reported for possessing improved cellular adhesion and proliferation. Here, we extended our investigation to establish the cellular compatibility of gelatin-grafted PDLLA with respect to mechanical properties of biological tissues. In this view, linear PDLLA-b-gelatin (l-pLG) was synthesized and tissue-level compatibility of 1-pLG and ss-pLG against fibroblasts (L929), myoblasts (C2C12) and preosteoblasts (MG-63) was examined. The cell proliferation of C2C12 was significantly higher within l-pLG scaffolds, whereas L929 showed intensified growth within ss-pLG scaffolds. The difference in cell proliferation may be attributed to the varying mechanical properties of scaffolds; where the stiffness of l-pLG scaffolds was notably higher than ss-pLG scaffolds, most likely due to the variable levels of gelatin grafting on the backbone of PDLLA. Therefore, gelatin grafting can be used to modulate mechanical property of the scaffolds and this study reveals the significance of the matrix stiffness to produce the successful 3D scaffolds for tissue engineering applications.

Porous Particle-Reinforced Bioactive Gelatin Scaffold for Large Segmental Bone Defect Repairing

Large segmental bone defect repairing remains a big challenge in clinics, and synthetic bone grafts suitable for this purpose are still highly demanded. In this article, hydrophilic composite scaffolds (bioactive hollow particle (BHP)-gel scaffold) composed of bioactive hollow nanoparticles and cross-linked gelatin have been developed. The bioactive nanoparticles have a porous structure as well as high specific surface area; thus, they interact strongly with gelatin to overcome the swelling problem that a hydrophilic polymer scaffold will usually face. With this combination, these BHP-gel scaffolds showed porous structure and mechanical properties similar to those of the cancellous bone. They also showed excellent bioactivity and cell growth promotion performance in vitro. The best of them, namely, 10BHP-gel scaffold, was evaluated in vivo on a rat femur model, where it was found that the 5 mm segmental bone defect almost healed with new bone tissue formed in 12 weeks and the scaffold itself degraded at the same time. Thus, 10BHP-gel scaffold may become a potential bone graft for large segmental bone defect healing in the future.

Three-dimensional macroporous materials for tissue engineering of craniofacial bone

Repair of critical-size defects caused by trauma, removal of a tumour, or congenital abnormalities is a challenge in the craniomaxillofacial region because of the limitations associated with treatment. We have reviewed research papers and updated information relevant to the various types of macroporous scaffolds. We have included papers on several biomaterials and their use in various craniofacial defects such as mandibular, calvarial, and others, as well as the latest technological developments such as 3-dimensional printed scaffolds. We selected all papers about scaffolds, stem cells, and growth factors for review. Initial selection was by review of titles and abstracts, and the full texts of potentially suitable articles were then assessed. Methods of tissue engineering for repair of critical-size defects in the craniofacial bones seem to be viable options for surgical treatment in the future. Macroporous scaffolds with interconnected pores are of great value in regeneration of bone in the craniofacial region. In recent years, various natural or synthetic materials, or both, have been developed, on which macroporous scaffolds can be based. In this review we present a review on the various types of three-dimensional macroporous scaffolds that have been developed in recent years, and evaluate their potential for regeneration of craniofacial bone.

Evaluation of the in vitro biodegradation and biological behavior of poly(lactic-co-glycolic acid)/nano-fluorhydroxyapatite composite microsphere-sintered scaffold for bone tissue engineering

The objective of this research was to study the degradation and biological characteristics of the three-dimensional porous composite scaffold made of poly(lactic- co-glycolic acid)/nano-fluorhydroxyapatite microsphere using sintering method for potential bone tissue engineering. Our previous experimental results demonstrated that poly(lactic- co-glycolic acid)/nano-fluorhydroxyapatite composite scaffold with a ratio of 4:1 sintered at 90ºC for 2 h has the greatest mechanical properties and a proper pore structure for bone repair applications. The weight loss percentage of both poly(lactic- co-glycolic acid)/nano-fluorhydroxyapatite and poly(lactic- co-glycolic acid) scaffolds demonstrated a monotonic trend with increasing degradation time, that is, the incorporation of nano-fluorhydroxyapatite into polymeric scaffold could lead to weight loss in comparison with that of pure poly(lactic- co-glycolic acid). The pH change for composite scaffolds showed that there was a slight decrease until 2 weeks after immersion in simulated body fluid, followed by a significant increase in the pH of simulated body fluid without a scaffold at the end of immersion time. The mechanical properties of composite scaffold were higher than that of poly(lactic- co-glycolic acid) scaffold at total time of incubation in simulated body fluid; however, it should be noted that the incorporation of nano-fluorhydroxyapatite into composite scaffold leads to decline in the relatively significant mechanical strength and modulus during hydrolytic degradation. In addition, MTT assay and alkaline phosphatase activity results defined that a general trend of increasing cell viability was seen for poly(lactic- co-glycolic acid)/nano-fluorhydroxyapatite scaffold sintered by time when compared to control group. Eventually, experimental results exhibited poly(lactic- co-glycolic acid)/nano-fluorhydroxyapatite microsphere-sintered scaffold is a promising scaffold for bone repair.

Tissue Engineering of the Intervertebral Disc's Annulus Fibrosus: A Scaffold-Based Review Study

Tissue engineering as a high technology solution for treating disc's problem has been the focus of some researches recently; however, the upcoming successful results in this area depends on understanding the complexities of biology and engineering interface. Whereas the major responsibility of the nucleus pulposus is to provide a sustainable hydrated environment within the disc, the function of the annulus fibrosus (AF) is more mechanical, facilitating joint mobility and preventing radial bulging by confining of the central part, which makes the AF reconstruction important. Although the body of knowledge regarding the AF tissue engineering has grown rapidly, the opportunities to improve current understanding of how artificial scaffolds are able to mimic the AF concentric structure-including inter-lamellar matrix and cross-bridges-addressed unresolved research questions. The aim of this literature review was to collect and discuss, from the international scientific literature, information about tissue engineering of the AF based on scaffold fabrication and material properties, useful for developing new strategies in disc tissue engineering. The key parameter of this research was understanding if role of cross-bridges and inter-lamellar matrix has been considered on tissue engineering of the AF.