1
|
Ho QN, Mitsuoka K, Yoshida N. Microbial fuel cell in long-term operation and providing electricity for intermittent aeration to remove contaminants from sewage. ENVIRONMENTAL RESEARCH 2024; 259:119503. [PMID: 38972342 DOI: 10.1016/j.envres.2024.119503] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 04/23/2024] [Revised: 06/04/2024] [Accepted: 06/26/2024] [Indexed: 07/09/2024]
Abstract
Microbial fuel cells (MFCs) show promise in sewage treatment because they can directly convert organic matter (OM) into electricity. This study aimed to demonstrate MFCs stability over 750 days of operation and efficient removal of OM and nitrogenous compounds from sewage. To enhance contaminant removal, oxygen was provided into the anode chamber via a mini air pump. This pump was powered by the MFCs' output voltage, which was boosted using a DC-DC converter. The experimental system consisted of 12 sets of cylindrical MFCs within a 246L-scale reactor. The boosted voltage reached 4.7 V. This voltage was first collected in capacitors every 5 min and then dispensed intermittently to the air pump for the MFCs reactor in 4 s. This corresponds to receiving average DO concentration reaching 0.34 ± 0.44 mg/L at 10 cm above the air-stone. Consequently, the degradation rate constants (k) for chemical oxygen demand (COD) and biological oxygen demand (BOD) in the presence of oxygen were 0.048 and 0.069, respectively, which surpassed those without oxygen by 0.039 and 0.044, respectively. Aeration also marginally improved the removal of ammonia because of its potential to create a favorable environment for the growth of anammox and ammonia-oxidizing bacteria such as Candidatus brocadia and Nitrospira. The findings of this study offer in-depth insight into the benefits of boosted voltage in MFCs, highlighting its potential to enhance contaminant degradation. This serves as a foundation for future research focused on improving MFCs performance, particularly for the removal of contaminants from wastewater.
Collapse
Affiliation(s)
- Que Nguyen Ho
- Department of Civil Engineering, Nagoya Institute of Technology (Nitech), Nagoya 466-8555, Aichi, Japan
| | - Kyosuke Mitsuoka
- Department of Civil Engineering, Nagoya Institute of Technology (Nitech), Nagoya 466-8555, Aichi, Japan
| | - Naoko Yoshida
- Department of Civil Engineering, Nagoya Institute of Technology (Nitech), Nagoya 466-8555, Aichi, Japan.
| |
Collapse
|
2
|
Ho QN, Hidaka T, Rahman MA, Yoshida N. Application of natural zeolite adsorption in cooperation with photosynthesis for the post-treatment of microbial fuel cells. RSC Adv 2024; 14:26484-26493. [PMID: 39175683 PMCID: PMC11339683 DOI: 10.1039/d4ra04672b] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Grants] [Track Full Text] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/27/2024] [Accepted: 08/13/2024] [Indexed: 08/24/2024] Open
Abstract
Microbial fuel cells (MFCs) are a promising technology that directly converts organic matter (OM) in wastewater into electricity while simultaneously degrading contaminants. However, MFCs are insufficient for the removal of nitrogenous compounds. Therefore, the post-treatment of MFCs is essential. This study was the first to use natural zeolite adsorption integrated with photosynthesis (ZP) for post-treating MFCs. In this system, no external energy was required; instead, natural light was used to promote the growth of photosynthetic microorganisms, thereby enhancing contaminants removal through the photosynthesis process. To assess the effectiveness of the method, comparisons were conducted under two conditions: dark (no photosynthesis) and light (with photosynthesis). In darkness, extending hydraulic retention time (HRT) enhanced COD and BOD removal by 19.8% and 28.9%, respectively. When exposed to natural light, improvements were even more notable, with COD and BOD removal reaching 32% and 40%, respectively. In both conditions, the method effectively removed NH4 +, achieving 60% efficiency in darkness and 84.5% in light. This study showed that the adsorption capacity of the zeolite reached saturation when the cumulative liquid volume per unit weight of the zeolite exceeded 0.2 L g-1. The key functional photosynthetic microbes were investigated using 16S rRNA and 18S rRNA. This revealed the presence of microorganisms such as Chlorobium, Acidovorax, Novosphingobium, and Scenedesmus, which likely play a role in enhancing the efficiency of photosynthesis in removing contaminants. The study findings indicated that the integration of MFCs-ZP represents an eco-friendly approach capable of resource recovery from wastewater while also meeting discharge standards.
Collapse
Affiliation(s)
- Que Nguyen Ho
- Department of Civil Engineering, Nagoya Institute of Technology Nagoya Japan
| | - Taira Hidaka
- Department of Environmental Engineering, Graduate School of Engineering, Kyoto University, Kyoto University Katsura Nishikyo Kyoto 615-8540 Japan
| | - Mukhlis A Rahman
- Advanced Membrane Technology Research Centre (AMTEC), School of Chemical and Energy Engineering (FCEE), Universiti Teknologi Malaysia 81310 UTM Skudai Johor Malaysia
| | - Naoko Yoshida
- Department of Civil Engineering, Nagoya Institute of Technology Nagoya Japan
| |
Collapse
|
3
|
Singh NK, Mathuriya AS, Mehrotra S, Pandit S, Singh A, Jadhav D. Advances in bioelectrochemical systems for bio-products recovery. ENVIRONMENTAL TECHNOLOGY 2024; 45:3853-3876. [PMID: 37491760 DOI: 10.1080/09593330.2023.2234676] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 06/10/2022] [Accepted: 06/28/2023] [Indexed: 07/27/2023]
Abstract
Bioelectrochemical systems (BES) have emerged as a sustainable and highly promising technology that has garnered significant attention from researchers worldwide. These systems provide an efficient platform for the removal and recovery of valuable products from wastewater, with minimal or no net energy loss. Among the various types of BES, microbial fuel cells (MFCs) are a notable example, utilizing microbial biocatalytic activities to generate electrical energy through the degradation of organic matter. Other BES variants include microbial desalination cells (MDCs), microbial electrolysis cells (MECs), microbial electrosynthesis cells (MXCs), microbial solar cells (MSCs), and more. BESs have demonstrated remarkable potential in the recovery of diverse products such as hydrogen, methane, volatile fatty acids, precious nutrients, and metals. Recent advancements in scaling up BESs have facilitated a more realistic assessment of their net energy recovery and resource yield in real-world applications. This comprehensive review focuses on the practical applications of BESs, from laboratory-scale developments to their potential for industrial commercialization. Specifically, it highlights successful examples of value-added product recovery achieved through various BES configurations. Additionally, this review critically evaluates the limitations of BESs and provides suggestions to enhance their performance at a larger scale, enabling effective implementation in real-world scenarios. By providing a thorough analysis of the current state of BES technology, this review aims to emphasize the tremendous potential of these systems for sustainable wastewater treatment and resource recovery. It underscores the significance of bridging the gap between laboratory-scale achievements and industrial implementation, paving the way for a more sustainable and resource-efficient future.
Collapse
Affiliation(s)
- Neeraj Kumar Singh
- Bio-POSITIVE, Department of Life Sciences, School of Basic Sciences and Research, Sharda University, Greater Noida, India
| | - Abhilasha Singh Mathuriya
- Bio-POSITIVE, Department of Life Sciences, School of Basic Sciences and Research, Sharda University, Greater Noida, India
- Ministry of Environment, Forest and Climate Change, New Delhi, India
| | - Smriti Mehrotra
- Bio-POSITIVE, Department of Life Sciences, School of Basic Sciences and Research, Sharda University, Greater Noida, India
| | - Soumya Pandit
- Bio-POSITIVE, Department of Life Sciences, School of Basic Sciences and Research, Sharda University, Greater Noida, India
| | - Anoop Singh
- Department of Scientific and Industrial Research (DSIR), Government of India, New Delhi, India
| | - Deepak Jadhav
- Department of Agricultural Engineering, Maharashtra Institute of Technology Aurangabad, Maharashtra, India
| |
Collapse
|
4
|
Li C, Liang D, Tian Y, Liu S, He W, Li Z, Yadav RS, Ma Y, Ji C, Yi K, Yang W, Feng Y. Sorting Out the Latest Advances in Separators and Pilot-Scale Microbial Electrochemical Systems for Wastewater Treatment: Concomitant Development, Practical Application, and Future Perspective. ENVIRONMENTAL SCIENCE & TECHNOLOGY 2024; 58:9471-9486. [PMID: 38776077 DOI: 10.1021/acs.est.4c03169] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/05/2024]
Abstract
To date, dozens of pilot-scale microbial fuel cell (MFC) devices have been successfully developed worldwide for treating various types of wastewater. The availability and configurations of separators are determining factors for the economic feasibility, efficiency, sustainability, and operability of these devices. Thus, the concomitant advances between the separators and pilot-scale MFC configurations deserve further clarification. The analysis of separator configurations has shown that their evolution proceeds as follows: from ion-selective to ion-non-selective, from nonpermeable to permeable, and from abiotic to biotic. Meanwhile, their cost is decreasing and their availability is increasing. Notably, the novel MFCs configured with biotic separators are superior to those configured with abiotic separators in terms of wastewater treatment efficiency and capital cost. Herein, a highly comprehensive review of pilot-scale MFCs (>100 L) has been conducted, and we conclude that the intensive stack of the liquid cathode configuration is more advantageous when wastewater treatment is the highest priority. The use of permeable biotic separators ensures hydrodynamic continuity within the MFCs and simplifies reactor configuration and operation. In addition, a systemic comparison is conducted between pilot-scale MFC devices and conventional decentralized wastewater treatment processes. MFCs showed comparable cost, higher efficiency, long-term stability, and significant superiority in carbon emission reduction. The development of separators has greatly contributed to the availability and usability of MFCs, which will play an important role in various wastewater treatment scenarios in the future.
Collapse
Affiliation(s)
- Chao Li
- The Key Laboratory of Water and Sediment Sciences, Ministry of Education, College of Environmental Sciences and Engineering, Peking University, No. 5 Yiheyuan Road, Haidian District, Beijing 100871, P. R. China
| | - Dandan Liang
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, No. 73 Huanghe Road, Nangang District, Harbin 150090, P. R. China
| | - Yan Tian
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, No. 73 Huanghe Road, Nangang District, Harbin 150090, P. R. China
| | - Shujuan Liu
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, No. 73 Huanghe Road, Nangang District, Harbin 150090, P. R. China
| | - Weihua He
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, No. 73 Huanghe Road, Nangang District, Harbin 150090, P. R. China
| | - Zeng Li
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, No. 73 Huanghe Road, Nangang District, Harbin 150090, P. R. China
| | - Ravi Shankar Yadav
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, No. 73 Huanghe Road, Nangang District, Harbin 150090, P. R. China
| | - Yamei Ma
- The Key Laboratory of Water and Sediment Sciences, Ministry of Education, College of Environmental Sciences and Engineering, Peking University, No. 5 Yiheyuan Road, Haidian District, Beijing 100871, P. R. China
| | - Chengcheng Ji
- The Key Laboratory of Water and Sediment Sciences, Ministry of Education, College of Environmental Sciences and Engineering, Peking University, No. 5 Yiheyuan Road, Haidian District, Beijing 100871, P. R. China
| | - Kexin Yi
- The Key Laboratory of Water and Sediment Sciences, Ministry of Education, College of Environmental Sciences and Engineering, Peking University, No. 5 Yiheyuan Road, Haidian District, Beijing 100871, P. R. China
| | - Wulin Yang
- The Key Laboratory of Water and Sediment Sciences, Ministry of Education, College of Environmental Sciences and Engineering, Peking University, No. 5 Yiheyuan Road, Haidian District, Beijing 100871, P. R. China
| | - Yujie Feng
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, No. 73 Huanghe Road, Nangang District, Harbin 150090, P. R. China
| |
Collapse
|
5
|
Malekmohammadi S, Mirbagheri SA. Scale-up single chamber of microbial fuel cell using agitator and sponge biocarriers. ENVIRONMENTAL TECHNOLOGY 2024; 45:2935-2943. [PMID: 37006176 DOI: 10.1080/09593330.2023.2197126] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 09/26/2022] [Accepted: 03/18/2023] [Indexed: 06/19/2023]
Abstract
Despite the high efficiency of microbial fuel cells (MFCs), MFCs cannot be a suitable alternative for treatment plants because of insufficient power generation and tiny reactors. Additionally, the increased reactor size and MFC stack result in a reduction in production power and reverse voltage. In this study, a larger MFC with a volume of 1.5 L has been designed called LMFC. A conventional MFC, called SMFC, with a volume of 0.157 L, was constructed and compared with LMFC. Moreover, the designed LMFC can be integrated with other treatment systems and generate significant electricity. In order to evaluate MFC's ability to integrate with other treatment systems, the LMFC reactor was converted into MFC-MBBR by adding sponge biocarriers. A 9.5 percent increase in reactor volume resulted in a 60 percent increase in power density from 290 (SMFC) to 530 (LMFC). An agitator effect was also investigated for better mixing and circulating substrate, which positively affected the power density by about 18%. Compared with LMFCs, the reactor with biocarriers generated a 28% higher power density. The COD removal efficiency of SMFC, LMFC, and MFC-MBBR reactors after 24 h was 85, 66, and 83%, respectively. After 80 h of operation, the Coulombic efficiency of the SMFC, LMFC, and MFC-MBBR reactors was 20.9, 45.43, and 47.28%, respectively. The doubling of coulombic efficiency from SMFC to LMFC reactor shows the design's success. The reduction of COD removal efficiency in LMFC is the reason for integrating this reactor with other systems, which was compensated by adding biocarriers.
Collapse
Affiliation(s)
- Sima Malekmohammadi
- Department of Environmental Engineering, Faculty of Civil Engineering, K. N. Toosi University of Technology, Tehran, Iran
| | - Seyed Ahmad Mirbagheri
- Department of Environmental Engineering, Faculty of Civil Engineering, K. N. Toosi University of Technology, Tehran, Iran
| |
Collapse
|
6
|
Jalili P, Ala A, Nazari P, Jalili B, Ganji DD. A comprehensive review of microbial fuel cells considering materials, methods, structures, and microorganisms. Heliyon 2024; 10:e25439. [PMID: 38371992 PMCID: PMC10873675 DOI: 10.1016/j.heliyon.2024.e25439] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/02/2023] [Revised: 01/02/2024] [Accepted: 01/26/2024] [Indexed: 02/20/2024] Open
Abstract
Microbial fuel cells (MFCs) are promising for generating renewable energy from organic matter and efficient wastewater treatment. Ensuring their practical viability requires meticulous optimization and precise design. Among the critical components of MFCs, the membrane separator plays a pivotal role in segregating the anode and cathode chambers. Recent investigations have shed light on the potential benefits of membrane-less MFCs in enhancing power generation. However, it is crucial to recognize that such configurations can adversely impact the electrocatalytic activity of anode microorganisms due to increased substrate and oxygen penetration, leading to decreased coulombic efficiency. Therefore, when selecting a membrane for MFCs, it is essential to consider key factors such as internal resistance, substrate loss, biofouling, and oxygen diffusion. Addressing these considerations carefully allows researchers to advance the performance and efficiency of MFCs, facilitating their practical application in sustainable energy production and wastewater treatment. Accelerated substrate penetration could also lead to cathode clogging and bacterial inactivation, reducing the MFC's efficiency. Overall, the design and optimization of MFCs, including the selection and use of membranes, are vital for their practical application in renewable energy generation and wastewater treatment. Further research is necessary to overcome the challenges of MFCs without a membrane and to develop improved membrane materials for MFCs. This review article aims to compile comprehensive information about all constituents of the microbial fuel cell, providing practical insights for researchers examining various variables in microbial fuel cell research.
Collapse
Affiliation(s)
- Payam Jalili
- Department of Mechanical Engineering, North Tehran Branch, Islamic Azad University, Tehran, Iran
| | - Amirhosein Ala
- Department of Mechanical Engineering, North Tehran Branch, Islamic Azad University, Tehran, Iran
| | - Parham Nazari
- Department of Mechanical Engineering, North Tehran Branch, Islamic Azad University, Tehran, Iran
| | - Bahram Jalili
- Department of Mechanical Engineering, North Tehran Branch, Islamic Azad University, Tehran, Iran
| | - Davood Domiri Ganji
- Department of Mechanical Engineering, Babol Noshirvani University of Technology, P.O. Box 484, Babol, Iran
| |
Collapse
|
7
|
Mehrotra S, Singh NK, Vempaty A, Mathuriya AS. Development, performance evaluation, and kinetic studies of microbial fuel cell based auto dripping bioelectrochemical reactor (AutoDriBER) for urine treatment. ENVIRONMENTAL TECHNOLOGY 2024; 45:902-915. [PMID: 36170025 DOI: 10.1080/09593330.2022.2130106] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 06/18/2022] [Accepted: 08/23/2022] [Indexed: 06/16/2023]
Abstract
A bioelectrochemical reactor is an assembly, which facilitates energy generation and resource recovery using electrochemically active microorganisms. To maximise energy production from wastewater in this bioreactor system special design is required. Therefore, in the present study, continuous flow auto dripping bioelectrochemical reactors (AutoDriBERs) were developed as a single and multi-electrode assembly for urine treatment. Further, their performance was assessed by connecting reactors in series and parallel arrangements. AutoDriBER configured in series connection showed the highest 93.64 ± 1.57% chemical oxygen demand removal rate with the 1.38 ± 0.64 V voltage and 2.54 W m-3 polarisation power density. The optimum flow rate for maximum voltage production was tested with various models i.e. the linear, exponential, Sweibull-1, and Sweibull-2 models to confirm voltage prediction and its validity. The Linear and exponential models were found best fitted for voltage production with R2 value of 0.999. These findings infer a novel approach toward optimisation of the complex, inexpensive and self-sufficient design for electricity generation from energy-rich urine wastewater in rural areas.
Collapse
Affiliation(s)
- Smriti Mehrotra
- Bio-POSITIVE, Department of Life Sciences, School of Basic Sciences and Research, Sharda University, Greater Noida, India
| | - Neeraj Kumar Singh
- Bio-POSITIVE, Department of Life Sciences, School of Basic Sciences and Research, Sharda University, Greater Noida, India
| | - Anusha Vempaty
- Bio-POSITIVE, Department of Life Sciences, School of Basic Sciences and Research, Sharda University, Greater Noida, India
| | - Abhilasha Singh Mathuriya
- Bio-POSITIVE, Department of Life Sciences, School of Basic Sciences and Research, Sharda University, Greater Noida, India
- Ministry of Environment, Forest and Climate Change, Indira Paryavaran Bhawan, New Delhi, India
| |
Collapse
|
8
|
Parekh D, Vaidh S, Ailani R, Banerjee S, Vishwakarma GS. Investigation of biochemical, enzymatic, and metagenomic profiles of garbage enzymes and its application in dumping site leachate treatment. ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH INTERNATIONAL 2024; 31:8974-8984. [PMID: 38183548 DOI: 10.1007/s11356-024-31850-z] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 03/14/2023] [Accepted: 12/31/2023] [Indexed: 01/08/2024]
Abstract
The current article focuses on the preparation and characterization of garbage enzyme (GE) and explores its applications in treating leachate. GE is prepared from fruit and vegetable wastes and characterized via analysis of metabolites, carbohydrates, proteins, antioxidants, and enzymatic activities. This study extends our understanding of GE by reporting the presence of various metabolites. Moreover, a metagenomic analysis of GE is presented, shedding light on the microbial diversity. Firmicutes emerged as the dominant phylum, surpassing other phyla, including Proteobacteria and Actinobacteria. When exploring the potential for leachate treatment, the results indicate that vegetable GE shows 68% reduction in COD (chemical oxygen demand) and 39% reduction in ammoniacal nitrogen. Similarly, non-citrus GE also showed 64% reduction in COD and a 37% reduction in ammoniacal nitrogen, followed by citrus GE with a 33% reduction in COD and a 34% reduction in ammoniacal nitrogen compared to the control.
Collapse
Affiliation(s)
- Dharni Parekh
- Department of Biotechnology and Bioengineering, Institute of Advanced Research, Gandhinagar, India
| | - Sachin Vaidh
- Department of Biotechnology and Bioengineering, Institute of Advanced Research, Gandhinagar, India
| | - Rachana Ailani
- Department of Biotechnology and Bioengineering, Institute of Advanced Research, Gandhinagar, India
| | - Shuvomoy Banerjee
- Department of Biotechnology and Bioengineering, Institute of Advanced Research, Gandhinagar, India
| | | |
Collapse
|
9
|
Kuznetsova LS, Arlyapov VA, Plekhanova YV, Tarasov SE, Kharkova AS, Saverina EA, Reshetilov AN. Conductive Polymers and Their Nanocomposites: Application Features in Biosensors and Biofuel Cells. Polymers (Basel) 2023; 15:3783. [PMID: 37765637 PMCID: PMC10536614 DOI: 10.3390/polym15183783] [Citation(s) in RCA: 3] [Impact Index Per Article: 3.0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/20/2023] [Revised: 09/10/2023] [Accepted: 09/13/2023] [Indexed: 09/29/2023] Open
Abstract
Conductive polymers and their composites are excellent materials for coupling biological materials and electrodes in bioelectrochemical systems. It is assumed that their relevance and introduction to the field of bioelectrochemical devices will only grow due to their tunable conductivity, easy modification, and biocompatibility. This review analyzes the main trends and trends in the development of the methodology for the application of conductive polymers and their use in biosensors and biofuel elements, as well as describes their future prospects. Approaches to the synthesis of such materials and the peculiarities of obtaining their nanocomposites are presented. Special emphasis is placed on the features of the interfaces of such materials with biological objects.
Collapse
Affiliation(s)
- Lyubov S. Kuznetsova
- Federal State Budgetary Educational Institution of Higher Education, Tula State University, 300012 Tula, Russia
| | - Vyacheslav A. Arlyapov
- Federal State Budgetary Educational Institution of Higher Education, Tula State University, 300012 Tula, Russia
| | - Yulia V. Plekhanova
- Federal Research Center «Pushchino Scientific Center for Biological Research of the Russian Academy of Sciences», G.K. Skryabin Institute of Biochemistry and Physiology of Microorganisms, Russian Academy of Sciences, 142290 Pushchino, Russia
| | - Sergei E. Tarasov
- Federal Research Center «Pushchino Scientific Center for Biological Research of the Russian Academy of Sciences», G.K. Skryabin Institute of Biochemistry and Physiology of Microorganisms, Russian Academy of Sciences, 142290 Pushchino, Russia
| | - Anna S. Kharkova
- Federal State Budgetary Educational Institution of Higher Education, Tula State University, 300012 Tula, Russia
| | - Evgeniya A. Saverina
- Federal State Budgetary Educational Institution of Higher Education, Tula State University, 300012 Tula, Russia
- Federal State Budgetary Institution of Science, N.D. Zelinsky Institute of Organic Chemistry, 119991 Moscow, Russia
| | - Anatoly N. Reshetilov
- Federal Research Center «Pushchino Scientific Center for Biological Research of the Russian Academy of Sciences», G.K. Skryabin Institute of Biochemistry and Physiology of Microorganisms, Russian Academy of Sciences, 142290 Pushchino, Russia
| |
Collapse
|
10
|
Li C, Yi K, Hu S, Yang W. Cathodic biofouling control by microbial separators in air-breathing microbial fuel cells. ENVIRONMENTAL SCIENCE AND ECOTECHNOLOGY 2023; 15:100251. [PMID: 36923605 PMCID: PMC10009452 DOI: 10.1016/j.ese.2023.100251] [Citation(s) in RCA: 1] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 10/14/2022] [Revised: 02/06/2023] [Accepted: 02/13/2023] [Indexed: 05/10/2023]
Abstract
Microbial fuel cells (MFCs) incorporating air-breathing cathodes have emerged as a promising eco-friendly wastewater treatment technology capable of operating on an energy-free basis. However, the inevitable biofouling of these devices rapidly decreases cathodic catalytic activity and also reduces the stability of MFCs during long-term operation. The present work developed a novel microbial separator for use in air-breathing MFCs that protects cathodic catalytic activity. In these modified devices, microbes preferentially grow on the microbial separator rather than the cathodic surface such that biofouling is prevented. Trials showed that this concept provided low charge transfer and mass diffusion resistance values during the cathodic oxygen reduction reaction of 4.6 ± 1.3 and 17.3 ± 6.8 Ω, respectively, after prolonged operation. The maximum power density was found to be stable at 1.06 ± 0.07 W m-2 throughout a long-term test and the chemical oxygen demand removal efficiency was increased to 92% compared with a value of 83% for MFCs exhibiting serious biofouling. In addition, a cathode combined with a microbial separator demonstrated less cross-cathode diffusion of oxygen to the anolyte. This effect indirectly induced the growth of electroactive bacteria and produced higher currents in air-breathing MFCs. Most importantly, the present microbial separator concept enhances both the lifespan and economics of air-breathing MFCs by removing the need to replace or regenerate the cathode during long-term operation. These results indicate that the installation of a microbial separator is an effective means of stabilizing power generation and ensuring the cost-effective performance of air-breathing MFCs intended for future industrial applications.
Collapse
|
11
|
Roy H, Rahman TU, Tasnim N, Arju J, Rafid MM, Islam MR, Pervez MN, Cai Y, Naddeo V, Islam MS. Microbial Fuel Cell Construction Features and Application for Sustainable Wastewater Treatment. MEMBRANES 2023; 13:membranes13050490. [PMID: 37233551 DOI: 10.3390/membranes13050490] [Citation(s) in RCA: 12] [Impact Index Per Article: 12.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 02/28/2023] [Revised: 04/21/2023] [Accepted: 04/27/2023] [Indexed: 05/27/2023]
Abstract
A microbial fuel cell (MFC) is a system that can generate electricity by harnessing microorganisms' metabolic activity. MFCs can be used in wastewater treatment plants since they can convert the organic matter in wastewater into electricity while also removing pollutants. The microorganisms in the anode electrode oxidize the organic matter, breaking down pollutants and generating electrons that flow through an electrical circuit to the cathode compartment. This process also generates clean water as a byproduct, which can be reused or released back into the environment. MFCs offer a more energy-efficient alternative to traditional wastewater treatment plants, as they can generate electricity from the organic matter in wastewater, offsetting the energy needs of the treatment plants. The energy requirements of conventional wastewater treatment plants can add to the overall cost of the treatment process and contribute to greenhouse gas emissions. MFCs in wastewater treatment plants can increase sustainability in wastewater treatment processes by increasing energy efficiency and reducing operational cost and greenhouse gas emissions. However, the build-up to the commercial-scale still needs a lot of study, as MFC research is still in its early stages. This study thoroughly describes the principles underlying MFCs, including their fundamental structure and types, construction materials and membrane, working mechanism, and significant process elements influencing their effectiveness in the workplace. The application of this technology in sustainable wastewater treatment, as well as the challenges involved in its widespread adoption, are discussed in this study.
Collapse
Affiliation(s)
- Hridoy Roy
- Department of Chemical Engineering, Bangladesh University of Engineering and Technology, Dhaka 1000, Bangladesh
| | - Tanzim Ur Rahman
- Department of Chemical Engineering, Bangladesh University of Engineering and Technology, Dhaka 1000, Bangladesh
| | - Nishat Tasnim
- Department of Chemical Engineering, Bangladesh University of Engineering and Technology, Dhaka 1000, Bangladesh
| | - Jannatul Arju
- Department of Chemical Engineering, Bangladesh University of Engineering and Technology, Dhaka 1000, Bangladesh
| | - Md Mustafa Rafid
- Department of Chemical Engineering, Bangladesh University of Engineering and Technology, Dhaka 1000, Bangladesh
| | - Md Reazul Islam
- Department of Civil Engineering, Louisiana Tech University, Ruston, LA 71270, USA
| | - Md Nahid Pervez
- Sanitary Environmental Engineering Division (SEED), Department of Civil Engineering, University of Salerno, via Giovanni Paolo II 132, 84084 Fisciano, SA, Italy
| | - Yingjie Cai
- Hubei Provincial Engineering Laboratory for Clean Production and High Value Utilization of Bio-Based Textile Materials, Wuhan Textile University, Wuhan 430200, China
| | - Vincenzo Naddeo
- Sanitary Environmental Engineering Division (SEED), Department of Civil Engineering, University of Salerno, via Giovanni Paolo II 132, 84084 Fisciano, SA, Italy
| | - Md Shahinoor Islam
- Department of Chemical Engineering, Bangladesh University of Engineering and Technology, Dhaka 1000, Bangladesh
- Department of Textile Engineering, Daffodil International University, Dhaka 1341, Bangladesh
| |
Collapse
|
12
|
Li D, Sun Y, Shi Y, Wang Z, Okeke S, Yang L, Zhang W, Xiao L. Structure evolution of air cathodes and their application in electrochemical sensor development and wastewater treatment. THE SCIENCE OF THE TOTAL ENVIRONMENT 2023; 869:161689. [PMID: 36682546 DOI: 10.1016/j.scitotenv.2023.161689] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 10/31/2022] [Revised: 01/13/2023] [Accepted: 01/14/2023] [Indexed: 06/17/2023]
Abstract
Cathode structure and material are the most important factors to determine the performance and cost of single chamber air-cathode microbial fuel cell (MFC), which is the most promising type of MFC technology. Since the first air cathode was invented in 2004, five major structures (1-layer, 2-layer, 3-layer, 4-layer and separator-support) have been invented and modified to fit new material, improve power performance and lower MFC cost. This paper reviewed the structure evolution of air cathodes in past 18 years. The benefits and drawbacks of these structures, in terms of power generation, material cost, fabrication procedure and modification process are analyzed. The practical application cases (e.g., sensor development and wastewater treatment) employed with different cathode structures were also summarized and analyzed. Based on practical performance and long-term cost analysis, the 2-layer cathode demonstrated much greater potential over other structures. Compared with traditional activated-sludge technology, the cost of an MFC-based system is becoming competitive when employing with 2-layer structure. This review not only provides a detailed development history of air cathode but also reveals the advantages/disadvantages of air cathode with different structures, which will promote the research and application of air-cathode MFC technology.
Collapse
Affiliation(s)
- Dunzhu Li
- Department of Civil, Structural and Environmental Engineering, Trinity College Dublin, Dublin 2, Ireland
| | - Yifan Sun
- Department of Civil, Structural and Environmental Engineering, Trinity College Dublin, Dublin 2, Ireland
| | - Yunhong Shi
- Department of Civil, Structural and Environmental Engineering, Trinity College Dublin, Dublin 2, Ireland
| | - Zeena Wang
- Department of Civil, Structural and Environmental Engineering, Trinity College Dublin, Dublin 2, Ireland
| | - Saviour Okeke
- Department of Civil, Structural and Environmental Engineering, Trinity College Dublin, Dublin 2, Ireland
| | - Luming Yang
- Department of Civil, Structural and Environmental Engineering, Trinity College Dublin, Dublin 2, Ireland
| | - Wen Zhang
- Department of Civil, Structural and Environmental Engineering, Trinity College Dublin, Dublin 2, Ireland
| | - Liwen Xiao
- Department of Civil, Structural and Environmental Engineering, Trinity College Dublin, Dublin 2, Ireland.
| |
Collapse
|
13
|
Zhou S, An W, Zhao K, Lin L, Yang S, Zhang Y, Xu M. Protection of electroactive biofilms against hypersaline shock by quorum sensing. WATER RESEARCH 2023; 233:119823. [PMID: 36871386 DOI: 10.1016/j.watres.2023.119823] [Citation(s) in RCA: 3] [Impact Index Per Article: 3.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 10/10/2022] [Revised: 01/22/2023] [Accepted: 02/26/2023] [Indexed: 06/18/2023]
Abstract
Quorum sensing (QS) is an ideal strategy for boosting the operating performance of electroactive biofilms (EABs), but its potential effects on the protection of electroactive biofilms against environmental shocks (e.g., hypersaline shock) have been rarely revealed. In this study, a QS signaling molecule, the N-(3-oxo-dodecanoyl)-L-homoserine lactone, was employed to promote the anti-shock property of the EABs against extreme saline shock. The maximum current density of the QS-regulated biofilm recovered to 0.17 mA/cm2 after 10% salinity exposure, which was much higher than those of its counterparts. The laser scanning confocal microscope confirmed a thicker and more compact biofilm with the presence of the QS signaling molecule. The extracellular polymeric substances (EPS) might play a crucial role in the anti-shocking behaviors, as the polysaccharides in EPS of QS-biofilm had doubled compared to the groups with acylase (the QS quencher). The microbial community analysis indicated that the QS molecule enriched the relative abundance of key species including Pseudomonas sp. and Geobacter sp., which were both beneficial to the stability and electroactivity of the biofilms. The functional genes related to the bacterial community were also up-regulated with the presence of the QS molecule. These results highlight the importance of QS effects in protecting electroactive biofilm under extreme environmental shock, which provides effective and feasible strategies for the future development of microbial electrochemical technologies.
Collapse
Affiliation(s)
- Shaofeng Zhou
- Guangdong Provincial Key Laboratory of Microbial Culture Collection and Application, State Key Laboratory of Applied Microbiology Southern China, Institute of Microbiology, Guangdong Academy of Sciences, Guangzhou 510070, China; Guangdong Key Laboratory of Environmental Catalysis and Health Risk Control, School of Environmental Science and Engineering, Institute of Environmental Health and Pollution Control, Guangdong University of Technology, Guangzhou 510006, China
| | - Wenwen An
- Guangdong Provincial Key Laboratory of Microbial Culture Collection and Application, State Key Laboratory of Applied Microbiology Southern China, Institute of Microbiology, Guangdong Academy of Sciences, Guangzhou 510070, China
| | - Kexin Zhao
- Institute of Eco-environmental and Soil Sciences, Guangdong Academy of Sciences, Guangzhou 510650, China
| | - Lizhou Lin
- Guangdong Provincial Key Laboratory of Microbial Culture Collection and Application, State Key Laboratory of Applied Microbiology Southern China, Institute of Microbiology, Guangdong Academy of Sciences, Guangzhou 510070, China
| | - Shan Yang
- Guangdong Provincial Key Laboratory of Microbial Culture Collection and Application, State Key Laboratory of Applied Microbiology Southern China, Institute of Microbiology, Guangdong Academy of Sciences, Guangzhou 510070, China
| | - Yifeng Zhang
- Department of Environmental and Resource Engineering, Technical University of Denmark, Lyngby DK-2800, Denmark
| | - Meiying Xu
- Guangdong Provincial Key Laboratory of Microbial Culture Collection and Application, State Key Laboratory of Applied Microbiology Southern China, Institute of Microbiology, Guangdong Academy of Sciences, Guangzhou 510070, China.
| |
Collapse
|
14
|
Jadhav DA, Chendake AD, Vinayak V, Atabani A, Ali Abdelkareem M, Chae KJ. Scale-up of the bioelectrochemical system: Strategic perspectives and normalization of performance indices. BIORESOURCE TECHNOLOGY 2022; 363:127935. [PMID: 36100187 DOI: 10.1016/j.biortech.2022.127935] [Citation(s) in RCA: 8] [Impact Index Per Article: 4.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 07/11/2022] [Revised: 09/03/2022] [Accepted: 09/06/2022] [Indexed: 06/15/2023]
Abstract
Electrochemists and ecological engineers find environmental bioelectrochemistry appealing; however, there is a big gap between expectations and actual progress in bioelectrochemical system (BES). Implementing such technology opens new opportunities for novel electrochemical reactions for resource recovery and effective wastewater treatment. Loopholes of BES exist in its scaling-up applications, and numerous attempts toward practical applications (200, 1000, and 1500 L) are key successive indicators toward its commercialization. This review emphasized the critical rethinking of standardization of performance indices i.e. current generation (A/m2), net energy recovery (kWh/kg·COD), product/resource yield (mM), and economic feasibility ($/kWh) to make fair comparison with the existing treatment system. Therefore, directional perspectives, including modularity, energy-cost balance, energy and resource recovery, have been proposed for the sustainable market of BES. The current state of the art and up-gradation in resource recovery and contaminant removal warrants a systematic rethinking of functional worth and niches of BES for practical applications.
Collapse
Affiliation(s)
- Dipak A Jadhav
- Department of Environmental Engineering, College of Ocean Science and Engineering, Korea Maritime and Ocean University, 727 Taejong-ro, Yeongdo-gu, Busan 49112, Republic of Korea; Interdisciplinary Major of Ocean Renewable Energy Engineering, Korea Maritime and Ocean University, 727 Taejong-ro, Yeongdo-gu, Busan 49112, Republic of Korea
| | - Ashvini D Chendake
- Department of Agricultural Engineering, Maharashtra Institute of Technology, Aurangabad, Maharashtra 431010, India
| | - Vandana Vinayak
- Diatom Nanoengineering and Metabolism Laboratory (DNM), School of Applied Science, Dr. Harisingh Gour Central University, Sagar, Madhya Pradesh 470003, India
| | - Abdulaziz Atabani
- Alternative Fuels Research Laboratory (AFRL), Energy Division, Department of Mechanical Engineering, Erciyes University, Turkey
| | - Mohammad Ali Abdelkareem
- Department of Sustainable and Renewable Energy Engineering, University of Sharjah, P.O. Box 27272, Sharjah, United Arab Emirates; Center for Advanced Materials Research, University of Sharjah, 27272 Sharjah, United Arab Emirates; Chemical Engineering Department, Faculty of Engineering, Minia University, AlMinya, Egypt
| | - Kyu-Jung Chae
- Department of Environmental Engineering, College of Ocean Science and Engineering, Korea Maritime and Ocean University, 727 Taejong-ro, Yeongdo-gu, Busan 49112, Republic of Korea; Interdisciplinary Major of Ocean Renewable Energy Engineering, Korea Maritime and Ocean University, 727 Taejong-ro, Yeongdo-gu, Busan 49112, Republic of Korea.
| |
Collapse
|
15
|
Rossi R, Logan BE. Impact of reactor configuration on pilot-scale microbial fuel cell performance. WATER RESEARCH 2022; 225:119179. [PMID: 36206685 DOI: 10.1016/j.watres.2022.119179] [Citation(s) in RCA: 12] [Impact Index Per Article: 6.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 04/22/2022] [Revised: 08/02/2022] [Accepted: 09/27/2022] [Indexed: 06/16/2023]
Abstract
Different microbial fuel cell (MFC) configurations have been successfully operated at pilot-scale levels (>100 L) to demonstrate electricity generation while accomplishing domestic or industrial wastewater treatment. Two cathode configurations have been primarily used based on either oxygen transfer by aeration of a liquid catholyte or direct oxygen transfer using air-cathodes. Analysis of several pilot-scale MFCs showed that air-cathode MFCs outperformed liquid catholyte reactors based on power density, producing 233% larger area-normalized power densities and 181% higher volumetric power densities. Reactors with higher electrode packing densities improved performance by enabling larger power production while minimizing the reactor footprint. Despite producing more power than the liquid catholyte MFCs, and reducing energy consumption for catholyte aeration, pilot MFCs based on air-cathode configuration failed to produce effluents with chemical oxygen demand (COD) levels low enough to meet typical threshold for discharge. Therefore, additional treatment would be required to further reduce the organic matter in the effluent to levels suitable for discharge. Scaling up MFCs must incorporate designs that can minimize electrode and solution resistances to maximize power and enable efficient wastewater treatment.
Collapse
Affiliation(s)
- Ruggero Rossi
- Department of Civil and Environmental Engineering, The Pennsylvania State University, University Park, PA 16802, USA.
| | - Bruce E Logan
- Department of Civil and Environmental Engineering, The Pennsylvania State University, University Park, PA 16802, USA
| |
Collapse
|
16
|
Tian Y, Li C, Liang D, Xie T, He W, Li D, Feng Y. Fungus-sourced filament-array anode facilitates Geobacter enrichment and promotes anodic bio-capacitance improvement for efficient power generation in microbial fuel cells. THE SCIENCE OF THE TOTAL ENVIRONMENT 2022; 838:155926. [PMID: 35588840 DOI: 10.1016/j.scitotenv.2022.155926] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 03/13/2022] [Revised: 05/07/2022] [Accepted: 05/10/2022] [Indexed: 06/15/2023]
Abstract
Microbial fuel cells (MFC) are emerging as new generation eco-friendly technology for the superiorities of energy harvest and simultaneous wastewater treatment. However, the power generation performance was strongly restricted by the material/biofilm electron transfer rate. In this research, the fungus-sourced electrode with filament-array structure was firstly proposed and prepared by one-step carbonization method. After 2 h pyrolysis, the functional groups containing N and O elements highly remained in the as-prepared material, which was beneficial to the electron transfer for the current generation. The lowest electron transfer resistance was obtained at 2.2 Ω, which showed a great reduction that compared with graphite sheet anode. With filament-array structure, the lowest mass diffusion resistance was obtained at 26.9 Ω for anodic oxidation reaction, which also supported the highest current generation performance. In addition, the relative abundance of typical electrochemical bacterium Geobacter was highly improved to 45.5% with an extraordinary electroactive biofilm loading of about 1203 ± 256 μg cm-2. More importantly, the high biocatalytic activity biofilm supported a remarkably observed bio-capacitance of about 1.14 F in 3DFfv anode, which exhibited the highest power density in 3.5 ± 0.2 W m-2. In addition, the fungus-sourced material was one kind of economical and readily available material. Overall, this work provided one efficient strategy for electrode preparation and higher power generation in MFCs, which would reduce the capital cost and improve the efficiency in further applications of MFCs.
Collapse
Affiliation(s)
- Yan Tian
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, No. 73 Huanghe Road, Nangang District, Harbin 150090, China
| | - Chao Li
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, No. 73 Huanghe Road, Nangang District, Harbin 150090, China
| | - DanDan Liang
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, No. 73 Huanghe Road, Nangang District, Harbin 150090, China
| | - Ting Xie
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, No. 73 Huanghe Road, Nangang District, Harbin 150090, China
| | - Weihua He
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, No. 73 Huanghe Road, Nangang District, Harbin 150090, China
| | - Da Li
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, No. 73 Huanghe Road, Nangang District, Harbin 150090, China
| | - Yujie Feng
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, No. 73 Huanghe Road, Nangang District, Harbin 150090, China.
| |
Collapse
|
17
|
Koffi NJ, Okabe S. High electrical energy harvesting performance of an integrated microbial fuel cell and low voltage booster-rectifier system treating domestic wastewater. BIORESOURCE TECHNOLOGY 2022; 359:127455. [PMID: 35710051 DOI: 10.1016/j.biortech.2022.127455] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 04/30/2022] [Revised: 06/05/2022] [Accepted: 06/09/2022] [Indexed: 06/15/2023]
Abstract
To harvest directly usable electrical energy from real domestic wastewater, a new power management system (PMS), transistor-based low voltage boosters followed by a voltage rectifier (LVBR), was developed and tested for its energy harvesting performance. Three air-cathode MFCs were individually linked with LVBs, which were electrically stacked in parallel and then connected with a single voltage rectifier (MFC-LVBR). The MFC-LVBR system could increase VMFCto 11.9 ± 0.6 V without voltage reversal, which was capable of charging a lithium-ion batteryand supercapacitor-based power banks. When the integrated MFC-LVBR system was linked with a lithium-ion battery, the highest normalized energy recovery (NERCOD) of 0.76 kWh/kg-COD (NERvolumeof 0.22 kWh/m3) was achieved with a minimal energy loss of 14.4%, whichwas much higher than those previously reported values.Furthermore, the electrical energy charged in the lithium-ion battery successfully powered a DC peristaltic pump requiring a minimum operating power of 0.46 W.
Collapse
Affiliation(s)
- N'Dah Joel Koffi
- Division of Environmental Engineering, Faculty of Engineering, Hokkaido University, North-13, West-8, Kita-ku, Sapporo, Hokkaido 060-8628, Japan
| | - Satoshi Okabe
- Division of Environmental Engineering, Faculty of Engineering, Hokkaido University, North-13, West-8, Kita-ku, Sapporo, Hokkaido 060-8628, Japan.
| |
Collapse
|
18
|
Parekh D, Vaidh S, Patel D, Vishwakarma GS. Temporal study of physicochemical parameters of leachates and assessment of solid waste and ground water quality of Pirana dumping site, Ahmedabad, India. ENVIRONMENTAL MONITORING AND ASSESSMENT 2022; 194:708. [PMID: 36006490 DOI: 10.1007/s10661-022-10402-3] [Citation(s) in RCA: 2] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 03/16/2022] [Accepted: 08/17/2022] [Indexed: 06/15/2023]
Abstract
The characterisation of solid waste (SW), leachate, is essential for developing an appropriate management strategy or treatment method. However, due to a range of contributing factors, such as waste type and dumping site locations, forecasting leachate quality is often challenging. This research article discusses leachate quality indicators and the temporal variations of leachate quality collected throughout various seasons and after 1-2 years of storage. In addition to that, the article also provides the data of different physicochemical parameters of SW and ground water (GW) quality collected from of Pirana solid waste dumping area (Pirana SWD), Ahmedabad, India, and surrounding areas throughout various seasons. The parameters like pH, COD, TDS, sulphates, nitrates, ammonia nitrogen, hardness, and heavy metals were all monitored to see whether there any temporal variations. When leachates were obtained 'fresh,' all parameters evaluated showed significantly higher values. As time passed, the values of the parameters (COD, ammonia nitrogen) stabilised. Heavy metals such as Hg, As, Pb, and Cr were detected in both fresh and old samples. Similarly in SW, the presence of heavy metals Hg (0.39 ppb), Pb (1.12 ppb), and Cr (16.86 ppb) were also detected. In case of GW, some samples also show the high TDS but the presence of metals like Cr, Ni, and Zn is less than permissible limit.
Collapse
Affiliation(s)
- Dharni Parekh
- Department of Biotechnology and Bioengineering, Institute of Advanced Research, Koba Institutional Area, 382 426, Gujarat, Gandhinagar, India
| | - Sachin Vaidh
- Department of Biotechnology and Bioengineering, Institute of Advanced Research, Koba Institutional Area, 382 426, Gujarat, Gandhinagar, India
| | - Dhruv Patel
- Department of Biotechnology and Bioengineering, Institute of Advanced Research, Koba Institutional Area, 382 426, Gujarat, Gandhinagar, India
| | - Gajendra Singh Vishwakarma
- Department of Biotechnology and Bioengineering, Institute of Advanced Research, Koba Institutional Area, 382 426, Gujarat, Gandhinagar, India.
| |
Collapse
|
19
|
Organic Waste Substrates for Bioenergy Production via Microbial Fuel Cells: A Key Point Review. ENERGIES 2022. [DOI: 10.3390/en15155616] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 12/07/2022]
Abstract
High-energy consumption globally has raised questions about the low environmentally friendly and high-cost processes used until now for energy production. Microbial fuel cells (MFCs) may support alternative more economically and environmentally favorable ways of bioenergy production based on their advantage of using waste. MFCs work as bio-electrochemical devices that consume organic substrates in order for the electrogenic bacteria and/or enzyme cultures to produce electricity and simultaneously lower the environmental hazardous value of waste such as COD. The utilization of organic waste as fuels in MFCs has opened a new research path for testing a variety of by-products from several industry sectors. This review presents several organic waste substrates that can be employed as fuels in MFCs for bioenergy generation and the effect of their usage on power density, COD (chemical oxygen demand) removal, and Coulombic efficiency enhancement. Moreover, a demonstration and comparison of the different types of mixed waste regarding their efficiency for energy generation via MFCs are presented. Future perspectives for manufacturing and cost analysis plans can support scale-up processes fulfilling waste-treatment efficiency and energy-output densities.
Collapse
|
20
|
He Y, Zhou Q, Mo F, Li T, Liu J. Bioelectrochemical degradation of petroleum hydrocarbons: A critical review and future perspectives. ENVIRONMENTAL POLLUTION (BARKING, ESSEX : 1987) 2022; 306:119344. [PMID: 35483484 DOI: 10.1016/j.envpol.2022.119344] [Citation(s) in RCA: 5] [Impact Index Per Article: 2.5] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 01/21/2022] [Revised: 04/11/2022] [Accepted: 04/20/2022] [Indexed: 06/14/2023]
Abstract
As typical pollutants, petroleum hydrocarbons that are widely present in various environmental media such as soil, water, sediments, and air, seriously endanger living organisms and human health. In the meantime, as a green environmental technology that integrates pollutant removal and resource recovery, bioelectrochemical systems (BESs) have been extensively applied to the removal of petroleum hydrocarbons from the environment. This review introduces working principles of BESs, following which it discusses the different reactor structures, application progresses, and key optimization factors when treating water, sewage sludges, sediments, and soil. Furthermore, bibliometrics was first used in this field to analyze the evolution of knowledge structure and forecast future hot topics. The research focus has shifted from the early generation of bioelectric energy to exploring mechanisms of soil remediation and microbial metabolisms, which will be closely integrated in the future. Finally, the future prospects of this field are proposed. This review focuses on the research status of bioelectrochemical degradation of petroleum hydrocarbons and provides a scientific reference for subsequent research.
Collapse
Affiliation(s)
- Yuqing He
- Ministry of Education Key Laboratory of Pollution Processes and Environmental Criteria, Tianjin Key Laboratory of Environmental Remediation and Pollution Control, College of Environmental Science and Engineering, Nankai University, Tianjin, 300350, China
| | - Qixing Zhou
- Ministry of Education Key Laboratory of Pollution Processes and Environmental Criteria, Tianjin Key Laboratory of Environmental Remediation and Pollution Control, College of Environmental Science and Engineering, Nankai University, Tianjin, 300350, China
| | - Fan Mo
- Ministry of Education Key Laboratory of Pollution Processes and Environmental Criteria, Tianjin Key Laboratory of Environmental Remediation and Pollution Control, College of Environmental Science and Engineering, Nankai University, Tianjin, 300350, China
| | - Tian Li
- Ministry of Education Key Laboratory of Pollution Processes and Environmental Criteria, Tianjin Key Laboratory of Environmental Remediation and Pollution Control, College of Environmental Science and Engineering, Nankai University, Tianjin, 300350, China
| | - Jianv Liu
- Ministry of Education Key Laboratory of Pollution Processes and Environmental Criteria, Tianjin Key Laboratory of Environmental Remediation and Pollution Control, College of Environmental Science and Engineering, Nankai University, Tianjin, 300350, China.
| |
Collapse
|
21
|
Li J, Chen D, Liu G, Li D, Tian Y, Feng Y. Construction of a new type of three-dimensional honeycomb-structure anode in microbial electrochemical systems for energy harvesting and pollutant removal. WATER RESEARCH 2022; 218:118429. [PMID: 35483206 DOI: 10.1016/j.watres.2022.118429] [Citation(s) in RCA: 15] [Impact Index Per Article: 7.5] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 01/24/2022] [Revised: 04/05/2022] [Accepted: 04/06/2022] [Indexed: 06/14/2023]
Abstract
Electrode materials occupy most of the construction cost of the microbial electrochemical system (MES), and the low mechanical strength and poor electrochemical performance of the commonly used traditional carbon-based materials restrict the promotion and application of this technology. In this study, polymer-based three-dimensional (3D) honeycomb-structure (HS) materials with good mechanical properties were used as supporting materials. Graphene (GR), carbon nanotube (CNT), and polypyrrole (PPy) was separately chosen as a surface conductivity coating layer for preparing MES anodes. The introduction of GR, CNT, and PPy on HS increased surface roughness, hydrophilicity, O and N content, electrochemically active surface area, and decreased charge transfer internal resistance, which promoted the adhesion of microorganisms on their surface and enhanced the extracellular electron transfer process at the electrode/microbe interface. The CNT-HS anode system got the better maximal power density (1700.7 ± 149.0 mW/m2) of the three modified anode systems and 3.60 times that of MES using CC (471.8 ± 27.2 mW/m2) as the anode. The accelerated reactions of the redox species in the outer cell membrane, the promoted electron shuttle secretion, and the enhanced abundance of the tricarboxylic acid cycle-related functional genes in biofilm led to better performance of the CNT-HS anode system. The CNT-HS anode system also exhibited long-term operational stability (>6 months) and a good chemical oxygen demand degradation effect. Furthermore, CNT-HS material exhibited its cost advantage, and its projected cost is estimated to be about $1.8/m2, much lower than the currently used MES anodes ($8.2-548.2/m2). Considering the good mechanical properties, simple preparation process, low manufacturing cost, long-term stability, excellent bio-electrochemical performance, and good pollutant removal ability, HS-based anode has promising potential for high-performance MES in applications.
Collapse
Affiliation(s)
- Jiannan Li
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, Harbin 150090, China
| | - Dahong Chen
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, Harbin 150090, China
| | - Guohong Liu
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, Harbin 150090, China.
| | - Da Li
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, Harbin 150090, China
| | - Yan Tian
- Harbin FengGe Ecological Environment Technology Co., Ltd., Harbin 150028, China
| | - Yujie Feng
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, Harbin 150090, China.
| |
Collapse
|
22
|
Impact of wastewater volume on cathode environment of the multi-anode shared cathode and standard single anode/cathode microbial fuel cells. CHEMICAL PAPERS 2022. [DOI: 10.1007/s11696-022-02316-8] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 11/03/2022]
|
23
|
Vaidh S, Parekh D, Patel D, Vishwakarma GS. Leachate treatment potential of nanomaterial based assemblies: a systematic review on recent development. WATER SCIENCE AND TECHNOLOGY : A JOURNAL OF THE INTERNATIONAL ASSOCIATION ON WATER POLLUTION RESEARCH 2022; 85:3285-3300. [PMID: 35704411 DOI: 10.2166/wst.2022.168] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/15/2023]
Abstract
Rapid development of the population has brought about a serious problem of waste generation and management. Open dumping and land filling are two of the preferred options for waste management and treatment. As a consequence of this, the accumulation of leachates has become one of the concerns for environmental sustainability. In this regard, various treatment methodologies have been developed in recent decades. Among them, the nanomaterial-based approaches are the emerging ones in the current scenario due to their various unique properties. Furthermore, nanomaterial-based assemblies (i.e., nanomaterials combined with microbes, chemical catalysts, enzymes, and so on) have been introduced as a novel modification for leachate treatment. This work, therefore, has been dedicated to comprehensively reviewing all nanomaterial based leachate treatment techniques. In this regard, the first part of this review will discuss the nano catalyst, nano adsorbent along with their synthesis and mechanistic view of pollutant removal potential. In the second part, the nanomaterial-based microbial conjugates applied in the leachate treatments have been discussed. Apart from this, various other nanomaterial-based methods have been discussed in the third part of the review. Hence this review is providing an insight of all the recent developments pertaining to the nano material based leachate treatment techniques.
Collapse
Affiliation(s)
- Sachin Vaidh
- Department of Biological Science and Biotechnology, Institute of Advanced Research, Gandhinagar, Gujarat 382426, India E-mail:
| | - Dharni Parekh
- Department of Biological Science and Biotechnology, Institute of Advanced Research, Gandhinagar, Gujarat 382426, India E-mail:
| | - Dhara Patel
- Department of Biological Science and Biotechnology, Institute of Advanced Research, Gandhinagar, Gujarat 382426, India E-mail:
| | - Gajendra Singh Vishwakarma
- Department of Biological Science and Biotechnology, Institute of Advanced Research, Gandhinagar, Gujarat 382426, India E-mail:
| |
Collapse
|
24
|
Yamane T, Yoshida N, Sugioka M. Simultaneous removal of organic matter and nitrogen compounds by partitioned aeration in a 226 L-scale microbial fuel cell. RSC Adv 2022; 12:15091-15097. [PMID: 35702426 PMCID: PMC9115875 DOI: 10.1039/d2ra01485h] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/06/2022] [Accepted: 05/02/2022] [Indexed: 11/21/2022] Open
Abstract
Although microbial fuel cells (MFCs) have been widely studied as wastewater treatment technologies that convert organic matter to electricity, there are few reports of large-scale MFCs that treat both organic matter and nitrogen compounds. In this study, a 226 L reactor equipped with 27 MFC units was partially aerated at 10% of its total volume. The MFC unit consists of a cylindrical air core covered with a carbon-based air cathode, an anion exchange membrane, and a graphite non-woven fabric anode. The air-cathode MFC with 13 L min-1 aeration rate produced a current density of 0.0012-0.15 A m-2 with 40 to >93% biological oxygen demand (BOD) removal to have an effluent BOD of <5-36 mg L-1 at a hydraulic retention time (HRT) of 12-47 h. Meanwhile, 55 ± 17% of the total nitrogen (TN) was removed, resulting in 9.7 ± 3.8 mg L-1 TN in the effluent, although the TN removal was limited at ≥20 °C. The mono-exponential regression for BOD and TN (≥20 °C) estimated that an HRT of 21 h could meet the Japanese effluent quality standards of BOD and TN. Calculation of the total energy recovered via current generation and energy consumed by aeration suggested an energy consumption of 0.22 kW h m-3. Decreasing the aeration rate and HRT in the reactor would further reduce energy consumption and increase energy production.
Collapse
Affiliation(s)
- Taiki Yamane
- Department of Civil and Environmental Engineering, Nagoya Institute of Technology (Nitech) Gokiso-Cho, Showa-Ku Nagoya Aichi Japan
| | - Naoko Yoshida
- Department of Civil and Environmental Engineering, Nagoya Institute of Technology (Nitech) Gokiso-Cho, Showa-Ku Nagoya Aichi Japan
| | - Mari Sugioka
- Department of Civil and Environmental Engineering, Nagoya Institute of Technology (Nitech) Gokiso-Cho, Showa-Ku Nagoya Aichi Japan
| |
Collapse
|
25
|
Li C, Feng Y, Liang D, Zhang L, Tian Y, Yadav RS, He W. Spatial-type skeleton induced Geobacter enrichment and tailored bio-capacitance of electroactive bioanode for efficient electron transfer in microbial fuel cells. THE SCIENCE OF THE TOTAL ENVIRONMENT 2022; 821:153123. [PMID: 35051486 DOI: 10.1016/j.scitotenv.2022.153123] [Citation(s) in RCA: 2] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 10/24/2021] [Revised: 01/08/2022] [Accepted: 01/10/2022] [Indexed: 06/14/2023]
Abstract
Microbial fuel cell (MFC) is a promising alternative to energy-intensive conventional wastewater technology. However, poor electron transfer efficiency, low coulombic recovery (CR), and high capital cost highly restricted its practical application. In this work, spatial electroactive biofilm is successfully developed on the carbonaceous skeleton derived from phenolic foam, which highly improved the bio-capacitance and Geobacter abundance of bioanode. Compared with carbon cloth (CC) anode, the optimal spatial electroactive biofilm (3DP_900) enriched the Geobacter abundance up to 56.8% from 17.2%, and obtained an extraordinary electroactive biomass loading of about 339 ± 63 μg cm-2 and a remarkable bio-capacitance of about 3.4 F. In general, spatial biofilm highly reduces the barriers to electron transfer (Rct) and mass transfer (Rd) in anodic substrate oxidation reaction and obtains the lowest Rct of 2.0 ± 0.2 Ω and Rd of 35 ± 3.3 Ω in 3DP_900, which also supports the highest power density at 0.347 ± 0.027 W m-2 and the highest CR at 69.2%. More importantly, due to its mature preparation technology, carbonized phenolic foam (2 cm thick pieces) reduces the capital cost of electrode preparation by three orders of magnitude from 1157.3 USD m-2 of CC to 5.2 USD m-2. Overall, this work offers an effective and scalable electrode to achieve high substrate utilization rate and energy recovery efficiency, and considers the economic cost of electrode fabrication for the further construction of pilot-scale MFCs equipment.
Collapse
Affiliation(s)
- Chao Li
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, No. 73 Huanghe Road, Nangang District, Harbin 150090, China
| | - Yujie Feng
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, No. 73 Huanghe Road, Nangang District, Harbin 150090, China
| | - Dandan Liang
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, No. 73 Huanghe Road, Nangang District, Harbin 150090, China
| | - Lijuan Zhang
- School of Environmental and Energy, Guangdong Provincial Key Laboratory of Solid Wastes Pollution Control and Recycling, South China University of Technology, Guangzhou, Guangdong 510006, China
| | - Yan Tian
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, No. 73 Huanghe Road, Nangang District, Harbin 150090, China
| | - Ravi Shankar Yadav
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, No. 73 Huanghe Road, Nangang District, Harbin 150090, China
| | - Weihua He
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, No. 73 Huanghe Road, Nangang District, Harbin 150090, China.
| |
Collapse
|
26
|
Rossi R, Hur AY, Page MA, Thomas AO, Butkiewicz JJ, Jones DW, Baek G, Saikaly PE, Cropek DM, Logan BE. Pilot scale microbial fuel cells using air cathodes for producing electricity while treating wastewater. WATER RESEARCH 2022; 215:118208. [PMID: 35255425 DOI: 10.1016/j.watres.2022.118208] [Citation(s) in RCA: 26] [Impact Index Per Article: 13.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 09/13/2021] [Revised: 10/23/2021] [Accepted: 02/15/2022] [Indexed: 06/14/2023]
Abstract
Microbial fuel cells (MFCs) can generate electrical energy from the oxidation of the organic matter, but they must be demonstrated at large scales, treat real wastewaters, and show the required performance needed at a site to provide a path forward for this technology. Previous pilot-scale studies of MFC technology have relied on systems with aerated catholytes, which limited energy recovery due to the energy consumed by pumping air into the catholyte. In the present study, we developed, deployed, and tested an 850 L (1400 L total liquid volume) air-cathode MFC treating domestic-type wastewater at a centralized wastewater treatment facility. The wastewater was processed over a hydraulic retention time (HRT) of 12 h through a sequence of 17 brush anode modules (11 m2 total projected anode area) and 16 cathode modules, each constructed using two air-cathodes (0.6 m2 each, total cathode area of 20 m2) with the air side facing each other to allow passive air flow. The MFC effluent was further treated in a biofilter (BF) to decrease the organic matter content. The field test was conducted for over six months to fully characterize the electrochemical and wastewater treatment performance. Wastewater quality as well as electrical energy production were routinely monitored. The power produced over six months by the MFC averaged 0.46 ± 0.35 W (0.043 W m-2 normalized to the cross-sectional area of an anode) at a current of 1.54 ± 0.90 A with a coulombic efficiency of 9%. Approximately 49 ± 15 % of the chemical oxygen demand (COD) was removed in the MFC alone as well as a large amount of the biochemical oxygen demand (BOD5) (70%) and total suspended solid (TSS) (48%). In the combined MFC/BF process, up to 91 ± 6 % of the COD and 91 % of the BOD5 were removed as well as certain bacteria (E. coli, 98.9%; fecal coliforms, 99.1%). The average effluent concentration of nitrate was 1.6 ± 2.4 mg L-1, nitrite was 0.17 ± 0.24 mg L-1 and ammonia was 0.4 ± 1.0 mg L-1. The pilot scale reactor presented here is the largest air-cathode MFC ever tested, generating electrical power while treating wastewater.
Collapse
Affiliation(s)
- Ruggero Rossi
- Department of Civil and Environmental Engineering, The Pennsylvania State University, University Park, PA 16802, USA
| | - Andy Y Hur
- U.S. Army Corps of Engineers, Engineer Research and Development Center, Construction Engineering Research Laboratory, Champaign, IL 61822, USA
| | - Martin A Page
- U.S. Army Corps of Engineers, Engineer Research and Development Center, Construction Engineering Research Laboratory, Champaign, IL 61822, USA.
| | | | | | - David W Jones
- Department of Civil and Environmental Engineering, The Pennsylvania State University, University Park, PA 16802, USA
| | - Gahyun Baek
- Department of Civil and Environmental Engineering, The Pennsylvania State University, University Park, PA 16802, USA
| | - Pascal E Saikaly
- Environmental Science and Engineering Program, Biological and Environmental Science and Engineering Division, King Abdullah University of Science and Technology (KAUST), Thuwal 23955-6900, Kingdom of Saudi Arabia; Water Desalination and Reuse Center, King Abdullah University of Science and Technology, Kingdom of Saudi Arabia
| | - Donald M Cropek
- U.S. Army Corps of Engineers, Engineer Research and Development Center, Construction Engineering Research Laboratory, Champaign, IL 61822, USA
| | - Bruce E Logan
- Department of Civil and Environmental Engineering, The Pennsylvania State University, University Park, PA 16802, USA.
| |
Collapse
|
27
|
Chauhan S, Sharma V, Varjani S, Sindhu R, Chaturvedi Bhargava P. Mitigation of tannery effluent with simultaneous generation of bioenergy using dual chambered microbial fuel cell. BIORESOURCE TECHNOLOGY 2022; 351:127084. [PMID: 35358671 DOI: 10.1016/j.biortech.2022.127084] [Citation(s) in RCA: 3] [Impact Index Per Article: 1.5] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 01/31/2022] [Revised: 03/24/2022] [Accepted: 03/25/2022] [Indexed: 06/14/2023]
Abstract
In this study, a dual chambered microbial fuel cell (MFC) was fabricated for the treatment of tannery wastewater with concurrent production of bio-energy. The tannery effluent acts as an anolyte and a synthetic electrolytic solution as the catholyte. Five electrochemically active bacteria from the biofilm were isolated that showed homology with Klebsiella quasipneumoniae, Klebsiella pneumoniae, Cloacibacterium normanese, Bacillus firmus and Pseudomonas reactans, using 16S rDNA analysis. The physiochemical studies of treated wastewater showcased the 88%, 74% and 94% reduction in COD, BOD and TDS level, respectively. The maximum voltage output and power density obtained using electroactive consortium in MFC was 940 mV and 7371 mW/cm3, respectively. The techno-economic feasibility of the bio-electrochemical system was studied for future bioprospecting. The present study reports a significant power generation with simultaneous effluent treatment up to a maximum of ∼85%, in a sustainable and eco-friendly manner.
Collapse
Affiliation(s)
- Shraddha Chauhan
- Aquatic Toxicology Laboratory, Environmental Toxicology Group, CSIR-Indian Institute of Toxicology Research, Vishvigyan Bhawan, 31, Mahatma Gandhi Marg, Lucknow 226 001, Uttar Pradesh, India
| | - Vikas Sharma
- Aquatic Toxicology Laboratory, Environmental Toxicology Group, CSIR-Indian Institute of Toxicology Research, Vishvigyan Bhawan, 31, Mahatma Gandhi Marg, Lucknow 226 001, Uttar Pradesh, India
| | | | - Raveendran Sindhu
- Department of Food Technology, TKM Institute of Technology, Kollam 691505, Kerala, India
| | - Preeti Chaturvedi Bhargava
- Aquatic Toxicology Laboratory, Environmental Toxicology Group, CSIR-Indian Institute of Toxicology Research, Vishvigyan Bhawan, 31, Mahatma Gandhi Marg, Lucknow 226 001, Uttar Pradesh, India.
| |
Collapse
|
28
|
Sugioka M, Yoshida N, Yamane T, Kakihana Y, Higa M, Matsumura T, Sakoda M, Iida K. Long-term evaluation of an air-cathode microbial fuel cell with an anion exchange membrane in a 226L wastewater treatment reactor. ENVIRONMENTAL RESEARCH 2022; 205:112416. [PMID: 34808126 DOI: 10.1016/j.envres.2021.112416] [Citation(s) in RCA: 10] [Impact Index Per Article: 5.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 08/30/2021] [Revised: 11/13/2021] [Accepted: 11/18/2021] [Indexed: 06/13/2023]
Abstract
Although the treatment of municipal wastewater using microbial fuel cells (MFCs) has been extensively studied, scaling the systems up for practical use remains challenging. In this study, a 226 L sewage treatment reactor was equipped with 27 MFC units, and its chemical oxygen demand (COD) removal and electricity production were evaluated. The MFC units were tubular air cores with a diameter of 5 cm and length of 100 cm, which were wrapped with a carbon-based cathode, anion exchange membrane (AEM), and nonwoven graphite fabric. The air-cathode-AEM MFC generated 0.12-0.30 A/m2, 0.072-0.51 W/m3, and 1.7-4.6 Wh/m3 in a chemostat reactor with a COD of 140-36 mg/L and hydraulic retention time (HRT) of 9-42 h throughout a year. The decrease in the COD was represented as the first-order rate constant of 0.038. The rate constant was comparable to that of other air-cathode MFCs with cation exchange membranes, indicating the necessity of a posttreatment to meet the discharge standard. It has been estimated that the MFC operation for 24 h before post-aeration can reduce the energy required to meet the discharge standard by 70%, suggesting the potential applicability of MFC in long HRT-treatments such as oxidation ditch. The resistances of the anode, cathode, and AEM were 15, 7.0, and 0.51 mΩ m2, respectively, and surface dirt rather than deterioration primarily increased the AEM resistance. A current exceeding 0.2 A/m2 significantly increases the anode potential, indicating that the current was limited by low COD. Increasing the anode-specific surface area can improve air-AEM MFCs used for practical applications.
Collapse
Affiliation(s)
- Mari Sugioka
- Department of Civil and Environmental Engineering, Nagoya Institute of Technology (Nitech), Gokiso-Cho, Showa-Ku, Nagoya, Aichi, Japan
| | - Naoko Yoshida
- Department of Civil and Environmental Engineering, Nagoya Institute of Technology (Nitech), Gokiso-Cho, Showa-Ku, Nagoya, Aichi, Japan.
| | - Taiki Yamane
- Department of Civil and Environmental Engineering, Nagoya Institute of Technology (Nitech), Gokiso-Cho, Showa-Ku, Nagoya, Aichi, Japan
| | - Yuriko Kakihana
- Graduate School of Sciences and Technology for Innovation, Yamaguchi University, Japan
| | - Mitsuru Higa
- Graduate School of Sciences and Technology for Innovation, Yamaguchi University, Japan
| | | | - Mitsuhiro Sakoda
- Water & Sewage Department, Tamano Consultants Co., Ltd., 2-17-14, Higashisakura, Higashi-ku, Nagoya, Aichi, Japan
| | - Kazuki Iida
- River & Water Resources Division, NIPPON KOEI Co., Ltd., 5-4 Kojimachi, Chiyoda-ku, Tokyo, Japan
| |
Collapse
|
29
|
Boas JV, Oliveira VB, Simões M, Pinto AMFR. Review on microbial fuel cells applications, developments and costs. JOURNAL OF ENVIRONMENTAL MANAGEMENT 2022; 307:114525. [PMID: 35091241 DOI: 10.1016/j.jenvman.2022.114525] [Citation(s) in RCA: 23] [Impact Index Per Article: 11.5] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 04/22/2021] [Revised: 01/11/2022] [Accepted: 01/13/2022] [Indexed: 06/14/2023]
Abstract
The microbial fuel cell (MFC) technology has attracted significant attention in the last years due to its potential to recover energy in a wastewater treatment. The idea of using an MFC in industry is very attractive as the organic wastes can be converted into energy, reducing the waste disposal costs and the energy needs while increasing the company profit. However, taking aside these promising prospects, the attempts to apply MFCs in large-scale have not been succeeded so far since their lower performance and high costs remains challenging. This review intends to present the main applications of the MFC systems and its developments, particularly the advances on configuration and operating conditions. The diagnostic techniques used to evaluate the MFC performance as well as the different modeling approaches are described. Towards the introduction of the MFC in the market, a cost analysis is also included. The development of low-cost materials and more efficient systems, with high higher power outputs and durability, are crucial towards the application of MFCs in industrial/large scale. This work is a helpful tool for discovering new operation and design regimes.
Collapse
Affiliation(s)
- Joana Vilas Boas
- CEFT, Department of Chemical Engineering, Faculty of Engineering of the University of Porto, Rua Dr. Roberto Frias, 4200-465, Porto, Portugal
| | - Vânia B Oliveira
- CEFT, Department of Chemical Engineering, Faculty of Engineering of the University of Porto, Rua Dr. Roberto Frias, 4200-465, Porto, Portugal.
| | - Manuel Simões
- LEPABE, Department of Chemical Engineering, Faculty of Engineering of the University of Porto, Rua Dr. Roberto Frias, 4200-465, Porto, Portugal
| | - Alexandra M F R Pinto
- CEFT, Department of Chemical Engineering, Faculty of Engineering of the University of Porto, Rua Dr. Roberto Frias, 4200-465, Porto, Portugal.
| |
Collapse
|
30
|
Paitier A, Haddour N, Gondran C, Vogel TM. Effect of Contact Area and Shape of Anode Current Collectors on Bacterial Community Structure in Microbial Fuel Cells. MOLECULES (BASEL, SWITZERLAND) 2022; 27:molecules27072245. [PMID: 35408642 PMCID: PMC9000358 DOI: 10.3390/molecules27072245] [Citation(s) in RCA: 4] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 02/17/2022] [Revised: 03/26/2022] [Accepted: 03/28/2022] [Indexed: 11/16/2022]
Abstract
Low electrical conductivity of carbon materials is a source of potential loss for large carbonaceous electrode surfaces of MFCs due to the long distance traveled by electrons to the collector. In this paper, different configurations of titanium current collectors were used to connect large surfaces of carbon cloth anodes. The current collectors had different distances and contact areas to the anode. For the same anode surface (490 cm2), increasing the contact area from 28 cm2 to 70 cm2 enhanced power output from 58 mW·m-2 to 107 mW·m-2. For the same contact area (28 cm2), decreasing the maximal distance of current collectors to anodes from 16.5 cm to 7.75 cm slightly increased power output from 50 mW·m-2 to 58 mW·m-2. Molecular biology characterization (qPCR and 16S rRNA gene sequencing) of anodic bacterial communities indicated that the Geobacter number was not correlated with power. Moreover, Geobacter and Desulfuromonas abundance increased with the drop in potential on the anode and with the presence of fermentative microorganisms. Electrochemical impedance spectroscopy (EIS) showed that biofilm resistance decreased with the abundance of electroactive bacteria. All these results showed that the electrical gradient arising from collectors shapes microbial communities. Consequently, current collectors influence the performance of carbon-based anodes for full-scale MFC applications.
Collapse
Affiliation(s)
- Agathe Paitier
- Laboratoire Ampère, Ecole Centrale de Lyon, Université de Lyon, CNRS, UMR 5005, 36 Avenue Guy de Collongue, 69134 Ecully, France;
- Environmental Microbial Genomics, Laboratoire Ampère, Université de Lyon, CNRS, UMR 5005, 43 Boulevard du 11 Novembre 1918, CEDEX, 69616 Villeurbanne, France;
| | - Naoufel Haddour
- Laboratoire Ampère, Ecole Centrale de Lyon, Université de Lyon, CNRS, UMR 5005, 36 Avenue Guy de Collongue, 69134 Ecully, France;
- Correspondence: ; Tel.: +33-4-72-18-61-12
| | - Chantal Gondran
- DCM, Université Grenoble Alpes, CNRS, 38000 Grenoble, France;
| | - Timothy M. Vogel
- Environmental Microbial Genomics, Laboratoire Ampère, Université de Lyon, CNRS, UMR 5005, 43 Boulevard du 11 Novembre 1918, CEDEX, 69616 Villeurbanne, France;
| |
Collapse
|
31
|
Day JR, Heidrich ES, Wood TS. A scalable model of fluid flow, substrate removal and current production in microbial fuel cells. CHEMOSPHERE 2022; 291:132686. [PMID: 34740702 DOI: 10.1016/j.chemosphere.2021.132686] [Citation(s) in RCA: 2] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 06/16/2021] [Revised: 09/24/2021] [Accepted: 10/23/2021] [Indexed: 06/13/2023]
Abstract
Mathematical modelling can reduce the cost and time required to design complex systems, and is being increasingly used in microbial electrochemical technologies (METs). To be of value such models must be complex enough to reproduce important behaviour of MET, yet simple enough to provide insight into underlying causes of this behaviour. Ideally, models must also be scalable to future industrial applications, rather than limited to describing existing laboratory experiments. We present a scalable model for simulating both fluid flow and bioelectrochemical processes in microbial fuel cells (MFCs), benchmarking against an experimental pilot-scale bioreactor. The model describes substrate transport through a two-dimensional fluid domain, and biofilm growth on anode surfaces. Electron transfer is achieved by an intracellular redox mediator. We find significant spatial variations in both substrate concentration and current density. Simple changes to the reactor layout can greatly improve the overall efficiency, measured in terms of substrate removal and total current generated.
Collapse
Affiliation(s)
- Jordan R Day
- Newcastle University, School of Engineering, NE1 7RU, Newcastle-upon-Tyne, UK.
| | | | - Toby S Wood
- Newcastle University, School of Mathematics, Statistics and Physics, NE17RU, Newcastle-upon-Tyne, UK
| |
Collapse
|
32
|
Selvasembian R, Mal J, Rani R, Sinha R, Agrahari R, Joshua I, Santhiagu A, Pradhan N. Recent progress in microbial fuel cells for industrial effluent treatment and energy generation: Fundamentals to scale-up application and challenges. BIORESOURCE TECHNOLOGY 2022; 346:126462. [PMID: 34863847 DOI: 10.1016/j.biortech.2021.126462] [Citation(s) in RCA: 23] [Impact Index Per Article: 11.5] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 09/25/2021] [Revised: 11/24/2021] [Accepted: 11/26/2021] [Indexed: 06/13/2023]
Abstract
Microbial fuel cells (MFCs) technology have the potential to decarbonize electricity generation and offer an eco-friendly route for treating a wide range of industrial effluents from power generation, petrochemical, tannery, brewery, dairy, textile, pulp/paper industries, and agro-industries. Despite successful laboratory-scale studies, several obstacles limit the MFC technology for real-world applications. This review article aimed to discuss the most recent state-of-the-art information on MFC architecture, design, components, electrode materials, and anodic exoelectrogens to enhance MFC performance and reduce cost. In addition, the article comprehensively reviewed the industrial effluent characteristics, integrating conventional technologies with MFCs for advanced resource recycling with a particular focus on the simultaneous bioelectricity generation and treatment of various industrial effluents. Finally, the article discussed the challenges, opportunities, and future perspectives for the large-scale applications of MFCs for sustainable industrial effluent management and energy recovery.
Collapse
Affiliation(s)
- Rangabhashiyam Selvasembian
- Department of Biotechnology, School of Chemical and Biotechnology, SASTRA Deemed University, Thanjavur 613401, Tamilnadu, India
| | - Joyabrata Mal
- Department of Biotechnology, Motilal Nehru National Institute of Technology Allahabad, Uttar Pradesh, India
| | - Radha Rani
- Department of Biotechnology, Motilal Nehru National Institute of Technology Allahabad, Uttar Pradesh, India
| | - Rupika Sinha
- Department of Biotechnology, Motilal Nehru National Institute of Technology Allahabad, Uttar Pradesh, India
| | - Roma Agrahari
- Department of Biotechnology, Motilal Nehru National Institute of Technology Allahabad, Uttar Pradesh, India
| | - Ighalo Joshua
- Department of Chemical Engineering, Nnamdi Azikiwe University, Nigeria
| | - Arockiasamy Santhiagu
- School of Biotechnology, National Institute of Technology Calicut, Kozhikode, Kerala, India
| | - Nirakar Pradhan
- Department of Biology, Faculty of Science, Hong Kong Baptist University, Hong Kong SAR, China.
| |
Collapse
|
33
|
Jadhav DA, Park SG, Pandit S, Yang E, Ali Abdelkareem M, Jang JK, Chae KJ. Scalability of microbial electrochemical technologies: Applications and challenges. BIORESOURCE TECHNOLOGY 2022; 345:126498. [PMID: 34890815 DOI: 10.1016/j.biortech.2021.126498] [Citation(s) in RCA: 22] [Impact Index Per Article: 11.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 10/09/2021] [Revised: 12/01/2021] [Accepted: 12/02/2021] [Indexed: 06/13/2023]
Abstract
During wastewater treatment, microbial electrochemical technologies (METs) are a promising means for in situ energy harvesting and resource recovery. The primary constraint for such systems is scaling them up from the laboratory to practical applications. Currently, most research (∼90%) has been limited to benchtop models because of bioelectrochemical, economic, and engineering design limitations. Field trials, i.e., 1.5 m3 bioelectric toilet, 1000 L microbial electrolysis cell and industrial applications of METs have been conducted, and their results serve as positive indicators of their readiness for practical applications. Multiple startup companies have invested in the pilot-scale demonstrations of METs for industrial effluent treatment. Recently, advances in membrane/electrode modification, understanding of microbe-electrode interaction, and feasibility of electrochemical redox reactions have provided new directions for realizing the practical application. This study reviews the scaling-up challenges, success stories for onsite use, and readiness level of METs for commercialization that is inexpensive and sustainable.
Collapse
Affiliation(s)
- Dipak A Jadhav
- Division of Civil, Environmental Engineering and Logistics System (Environmental Major), College of Ocean Science and Engineering, Korea Maritime and Ocean University, 727 Taejong-ro, Yeongdo-gu, Busan 49112, Republic of Korea; Department of Agricultural Engineering, Maharashtra Institute of Technology, Aurangabad, Maharashtra 431010, India
| | - Sung-Gwan Park
- Division of Civil, Environmental Engineering and Logistics System (Environmental Major), College of Ocean Science and Engineering, Korea Maritime and Ocean University, 727 Taejong-ro, Yeongdo-gu, Busan 49112, Republic of Korea
| | - Soumya Pandit
- Department of Life Sciences, School of Basic Sciences and Research, Sharda University, Greater Noida 201306, India
| | - Euntae Yang
- Department of Marine Environmental Engineering, Gyeongsang National University, Gyeongsangnam-do 53064, Republic of Korea
| | - Mohammad Ali Abdelkareem
- Department of Sustainable and Renewable Energy Engineering, University of Sharjah, P.O. Box 27272, Sharjah, United Arab Emirates; Center for Advanced Materials Research, University of Sharjah, 27272 Sharjah, United Arab Emirates; Chemical Engineering Department, Faculty of Engineering, Minia University, AlMinya, Egypt
| | - Jae-Kyung Jang
- National Institute of Agricultural Sciences, Department of Agricultural Engineering Energy and Environmental Engineering Division, 310 Nongsaengmyeong-ro, Deokjin-gu, Jeonju-si, Jeollabuk-do, Republic of Korea
| | - Kyu-Jung Chae
- Division of Civil, Environmental Engineering and Logistics System (Environmental Major), College of Ocean Science and Engineering, Korea Maritime and Ocean University, 727 Taejong-ro, Yeongdo-gu, Busan 49112, Republic of Korea; Interdisciplinary Major of Ocean Renewable Energy Engineering, Korea Maritime and Ocean University, 727 Taejong-ro, Yeongdo-gu, Busan 49112, Republic of Korea.
| |
Collapse
|
34
|
From Waste to Watts: Updates on Key Applications of Microbial Fuel Cells in Wastewater Treatment and Energy Production. SUSTAINABILITY 2022. [DOI: 10.3390/su14020955] [Citation(s) in RCA: 8] [Impact Index Per Article: 4.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 02/01/2023]
Abstract
Due to fossil fuel depletion and the rapid growth of industry, it is critical to develop environmentally friendly and long-term alternative energy technologies. Microbial fuel cells (MFCs) are a powerful platform for extracting energy from various sources and converting it to electricity. As no intermediate steps are required to harness the electricity from the organic substrate’s stored chemical energy, MFC technology offers a sustainable alternative source of energy production. The generation of electricity from the organic substances contained in waste using MFC technology could provide a cost-effective solution to the issue of environmental pollution and energy shortages in the near future. Thus, technical advancements in bioelectricity production from wastewater are becoming commercially viable. Due to practical limitations, and although promising prospects have been reported in recent investigations, MFCs are incapable of upscaling and of high-energy production. In this review paper, intensive research has been conducted on MFCs’ applications in the treatment of wastewater. Several types of waste have been extensively studied, including municipal or domestic waste, industrial waste, brewery wastewater, and urine waste. Furthermore, the applications of MFCs in the removal of nutrients (nitrogen and sulphates) and precious metals from wastewater were also intensively reviewed. As a result, the efficacy of various MFCs in achieving sustainable power generation from wastewater has been critically addressed in this study.
Collapse
|
35
|
Mathuriya AS. Development of trickling bio-electrochemical reactor (TrickBER) for large scale energy efficient wastewater treatment. ENVIRONMENTAL TECHNOLOGY 2022; 43:550-559. [PMID: 32674685 DOI: 10.1080/09593330.2020.1797893] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 11/03/2019] [Accepted: 07/08/2020] [Indexed: 06/11/2023]
Abstract
Bioelectrochemical systems such as microbial fuel cells are novel systems; those directly transform the chemical energy contained in organics of wastewater into electrical energy by the metabolic action of the microbial community. During the last two decades, bioelectrochemical systems astonishingly increased their wastewater treatment capabilities, sustainability, and power output. However, studies on scalable architectural designs of bioelectrochemical systems received less attention. Lower power yield and high cost are two major limitations for scaling up of bioelectrochemical systems. This study reports a low cost, scalable, air cathode bio-electrochemical reactor, constructed by adopting a trickling filtration approach (TrickBER) and operated in continuous mode. Various facets of construction, installation, and operation of TrickBER were investigated and optimized to achieve an efficient performance. TrickBER was found suitable in simultaneous electricity generation during continuous wastewater treatment and, in the future, could be used in small/cottage industries.
Collapse
Affiliation(s)
- Abhilasha Singh Mathuriya
- Department of Life Sciences, School of Basic Sciences and Research, Sharda University Greater Noida- 201306, India
- Department of Biotechnology, Anand Engineering College, Keetham
| |
Collapse
|
36
|
Gudiukaite R, Nadda AK, Gricajeva A, Shanmugam S, Nguyen DD, Lam SS. Bioprocesses for the recovery of bioenergy and value-added products from wastewater: A review. JOURNAL OF ENVIRONMENTAL MANAGEMENT 2021; 300:113831. [PMID: 34649321 DOI: 10.1016/j.jenvman.2021.113831] [Citation(s) in RCA: 3] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 01/18/2021] [Revised: 09/04/2021] [Accepted: 09/22/2021] [Indexed: 06/13/2023]
Abstract
Wastewater and activated sludge present a major challenge worldwide. Wastewater generated from large and small-scale industries, laundries, human residential areas and other sources is emerging as a main problem in sanitation and maintenance of smart/green cities. During the last decade, different technologies and processes have been developed to recycle and purify the wastewater. Currently, identification and fundamental consideration of development of more advanced microbial-based technologies that enable wastewater treatment and simultaneous resource recovery to produce bioenergy, biofuels and other value-added compounds (organic acids, fatty acids, bioplastics, bio-pesticides, bio-surfactants and bio-flocculants etc.) became an emerging topic. In the last several decades, significant development of bioprocesses and techniques for the extraction and recovery of mentioned valuable molecules and compounds from wastewater, waste biomass or sludge has been made. This review presents different microbial-based process routes related to resource recovery and wastewater application for the production of value-added products and bioenergy. Current process limitations and insights for future research to promote more efficient and sustainable routes for this under-utilized and continually growing waste stream are also discussed.
Collapse
Affiliation(s)
- Renata Gudiukaite
- Department of Microbiology and Biotechnology, Institute of Biosciences, Life Sciences Center, Vilnius University, Sauletekis Avenue 7, LT-10257, Vilnius, Lithuania.
| | - Ashok Kumar Nadda
- Department of Biotechnology and Bioinformatics, Jaypee University of Information Technology, Waknaghat, Solan, 173 234, India.
| | - Alisa Gricajeva
- Department of Microbiology and Biotechnology, Institute of Biosciences, Life Sciences Center, Vilnius University, Sauletekis Avenue 7, LT-10257, Vilnius, Lithuania
| | - Sabarathinam Shanmugam
- Key Laboratory of Low-grade Energy Utilization Technologies and Systems, Chongqing University, Ministry of Education, Chongqing, 400044, China
| | - D Duc Nguyen
- Department of Environmental Energy Engineering, Kyonggi University, Gwanggyosan-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 442-760, South Korea
| | - Su Shiung Lam
- Higher Institution Centre of Excellence (HICoE), Institute of Tropical Aquaculture and Fisheries (AKUATROP), Universiti Malaysia Terengganu, 21030, Kuala Nerus, Terengganu, Malaysia
| |
Collapse
|
37
|
Al-Sahari M, Al-Gheethi A, Radin Mohamed RMS, Noman E, Naushad M, Rizuan MB, Vo DVN, Ismail N. Green approach and strategies for wastewater treatment using bioelectrochemical systems: A critical review of fundamental concepts, applications, mechanism, and future trends. CHEMOSPHERE 2021; 285:131373. [PMID: 34265718 DOI: 10.1016/j.chemosphere.2021.131373] [Citation(s) in RCA: 16] [Impact Index Per Article: 5.3] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 04/10/2021] [Revised: 05/26/2021] [Accepted: 06/26/2021] [Indexed: 06/13/2023]
Abstract
Millions of litters of multifarious wastewater are directly disposed into the environment annually to reduce the processing costs leading to eutrophication and destroying the clean water sources. The bioelectrochemical systems (BESs) have recently received significant attention from researchers due to their ability to convert waste into energy and their high efficiency of wastewater treatment. However, most of the performed researches of the BESs have focused on energy generation, which created a literature gap on the utilization of BESs for wastewater treatment. The review highlights this gap from various aspects, including the BESs trends, fundamentals, applications, and mechanisms. A different review approach has followed in the present work using a bibliometric review (BR) which defined the literature gap of BESs publications in the degradation process section and linked the systematic review (SR) with it to prove and review the finding systematically. The degradation mechanisms of the BESs have been illustrated comprehensively in the current work, and various suggestions have been provided for supporting future studies and cooperation.
Collapse
Affiliation(s)
- Mohammed Al-Sahari
- Micropollutant Research Centre (MPRC), Faculty of Civil Engineering & Built Environment, Universiti Tun Hussein Onn Malaysia, Parit Raja, 86400, Johor, Malaysia.
| | - Adel Al-Gheethi
- Micropollutant Research Centre (MPRC), Faculty of Civil Engineering & Built Environment, Universiti Tun Hussein Onn Malaysia, Parit Raja, 86400, Johor, Malaysia.
| | - Radin Maya Saphira Radin Mohamed
- Micropollutant Research Centre (MPRC), Faculty of Civil Engineering & Built Environment, Universiti Tun Hussein Onn Malaysia, Parit Raja, 86400, Johor, Malaysia.
| | - Efaq Noman
- Department of Applied Microbiology, Faculty of Applied Science, Taiz University, Taiz, 00967, Yemen; Faculty of Applied Sciences and Technology, University Tun Hussein Onn Malaysia (UTHM), Pagoh Higher Education Hub, KM 1, Jalan Panchor, Panchor, 84000, Johor, Malaysia.
| | - M Naushad
- Advanced Materials Research Chair, Department of Chemistry, College of Science, King Saud University, Riyadh 11451, Saudi Arabia; Yonsei Frontier Lab, Yonsei University, Seoul, Republic of Korea
| | - Mohd Baharudin Rizuan
- Micropollutant Research Centre (MPRC), Faculty of Civil Engineering & Built Environment, Universiti Tun Hussein Onn Malaysia, Parit Raja, 86400, Johor, Malaysia
| | - Dai-Viet N Vo
- Center of Excellence for Green Energy and Environmental Nanomaterials (CE@GrEEN), Nguyen Tat Thanh University, 300A Nguyen Tat Thanh, District 4, Ho Chi Minh City, 755414, Viet Nam; College of Medical and Health Science, Asia University, Taichung, Taiwan
| | - Norli Ismail
- School of Industrial Technology, Universiti Sains Malaysia (USM), 11800, Peneng, Malaysia
| |
Collapse
|
38
|
Microbial Fuel Cell United with Other Existing Technologies for Enhanced Power Generation and Efficient Wastewater Treatment. APPLIED SCIENCES-BASEL 2021. [DOI: 10.3390/app112210777] [Citation(s) in RCA: 9] [Impact Index Per Article: 3.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 11/17/2022]
Abstract
Nowadays, the world is experiencing an energy crisis due to extensive globalization and industrialization. Most of the sources of renewable energy are getting depleted, and thus, there is an urge to locate alternative routes to produce energy efficiently. Microbial fuel cell (MFC) is a favorable technology that utilizes electroactive microorganisms acting as a biocatalyst at the anode compartment converting organic matter present in sewage water for bioelectricity production and simultaneously treating wastewater. However, there are certain limitations with a typical stand-alone MFC for efficient energy recovery and its practical implementation, including low power output and high cost associated with treatment. There are various modifications carried out on MFC for eliminating the limitations of a stand-alone MFC. Examples of such modification include integration of microbial fuel cell with capacitive deionization technology, forward osmosis technology, anaerobic digester, and constructed wetland technology. This review describes various integrated MFC systems along with their potential application on an industrial scale for wastewater treatment, biofuel generation, and energy production. As a result, such integration of MFCs with existing systems is urgently needed to address the cost, fouling, durability, and sustainability-related issues of MFCs while also improving the grade of treatment received by effluent.
Collapse
|
39
|
Yang N, Zhan G, Luo H, Xiong X, Li D. Integrated simultaneous nitrification/denitrification and comammox consortia as efficient biocatalysts enhance treatment of domestic wastewater in different up-flow bioelectrochemical reactors. BIORESOURCE TECHNOLOGY 2021; 339:125604. [PMID: 34303104 DOI: 10.1016/j.biortech.2021.125604] [Citation(s) in RCA: 10] [Impact Index Per Article: 3.3] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 06/09/2021] [Revised: 07/14/2021] [Accepted: 07/15/2021] [Indexed: 06/13/2023]
Abstract
Simultaneous nitrification/denitrification (SND) can efficiently deplete NH4+ by using air-exposed biocathode (AEB) in bioelectrochemical reactors. However, the fluctuation of wastewater adversely affects the functional biofilms and therefore the performance. In this work, four up-flow bioelectrochemical reactors (UBERs) with some novel inocula were investigated to improve domestic wastewater treatment. The UBERs exhibited favorable removal of chemical oxygen demand (COD, 95%), NH4+-N (99%), and total nitrogen (TN, 99%). The maximum of current (2.7 A/m3), power density (136 mW/m3) and coulombic efficiency (20.5%) were obtained. Cyclic voltammetry analysis showed all the electrodes were of diversified catalytic reactions. Illumina pyrosequencing showed the predominant Ignavibacterium, Thauera, Nitrosomonas, Geminicoccus and Nitrospira were in all electrodes, contributing functional biofilms performing SND, comammox, and bioelectrochemical reactions. FAPROTAX analysis confirmed twenty-one functional groups with obvious changes related to chemoheterotrophy, respiration/oxidation/denitrification of nitrite and nitrate. Comfortingly, such novel diversified consortia in UBERs enhance the microbial metabolisms to treat domestic wastewater.
Collapse
Affiliation(s)
- Nuan Yang
- Key Laboratory of Development and Application of Rural Renewable Energy, Ministry of Agriculture and Rural Affairs, Biogas Institute of Ministry of Agriculture and Rural Affairs (BIOMA), Chengdu 610041, China; CAS Key Laboratory of Environmental and Applied Microbiology, Environmental Microbiology Key Laboratory of Sichuan Province, Chengdu Institute of Biology, Chinese Academy of Sciences, Chengdu 610041, China.
| | - Guoqiang Zhan
- CAS Key Laboratory of Environmental and Applied Microbiology, Environmental Microbiology Key Laboratory of Sichuan Province, Chengdu Institute of Biology, Chinese Academy of Sciences, Chengdu 610041, China
| | - Huiqin Luo
- CAS Key Laboratory of Environmental and Applied Microbiology, Environmental Microbiology Key Laboratory of Sichuan Province, Chengdu Institute of Biology, Chinese Academy of Sciences, Chengdu 610041, China
| | - Xia Xiong
- Key Laboratory of Development and Application of Rural Renewable Energy, Ministry of Agriculture and Rural Affairs, Biogas Institute of Ministry of Agriculture and Rural Affairs (BIOMA), Chengdu 610041, China
| | - Daping Li
- CAS Key Laboratory of Environmental and Applied Microbiology, Environmental Microbiology Key Laboratory of Sichuan Province, Chengdu Institute of Biology, Chinese Academy of Sciences, Chengdu 610041, China
| |
Collapse
|
40
|
Zhu QL, Wu B, Pisutpaisal N, Wang YW, Ma KD, Dai LC, Qin H, Tan FR, Maeda T, Xu YS, Hu GQ, He MX. Bioenergy from dairy manure: technologies, challenges and opportunities. THE SCIENCE OF THE TOTAL ENVIRONMENT 2021; 790:148199. [PMID: 34111785 DOI: 10.1016/j.scitotenv.2021.148199] [Citation(s) in RCA: 7] [Impact Index Per Article: 2.3] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 02/04/2021] [Revised: 05/27/2021] [Accepted: 05/28/2021] [Indexed: 06/12/2023]
Abstract
Dairy manure (DM) is a kind of cheap cellulosic biomass resource which includes lignocellulose and mineral nutrients. Random stacks not only leads damage to the environment, but also results in waste of natural resources. The traditional ways to use DM include returning it to the soil or acting as a fertilizer, which could reduce environmental pollution to some extent. However, the resource utilization rate is not high and socio-economic performance is not utilized. To expand the application of DM, more and more attention has been paid to explore its potential as bioenergy or bio-chemicals production. This article presented a comprehensive review of different types of bioenergy production from DM and provided a general overview for bioenergy production. Importantly, this paper discussed potentials of DM as candidate feedstocks not only for biogas, bioethanol, biohydrogen, microbial fuel cell, lactic acid, and fumaric acid production by microbial technology, but also for bio-oil and biochar production through apyrolysis process. Additionally, the use of manure for replacing freshwater or nutrients for algae cultivation and cellulase production were also discussed. Overall, DM could be a novel suitable material for future biorefinery. Importantly, considerable efforts and further extensive research on overcoming technical bottlenecks like pretreatment, the effective release of fermentable sugars, the absence of robust organisms for fermentation, energy balance, and life cycle assessment should be needed to develop a comprehensive biorefinery model.
Collapse
Affiliation(s)
- Qi-Li Zhu
- Biomass Energy Technology Research Centre, Key Laboratory of Development and Application of Rural Renewable Energy (Ministry of Agriculture and Rural Affairs), Biogas Institute of Ministry of Agriculture and Rural Affairs, Section 4-13, Renmin South Road, Chengdu 610041, PR China; Department of Biological Functions Engineering, Graduate School of Life Science and Systems Engineering, Kyushu Institute of Technology, 2-4 Hibikino,Wakamatsu, Kitakyushu 808-0196, Japan.
| | - Bo Wu
- Biomass Energy Technology Research Centre, Key Laboratory of Development and Application of Rural Renewable Energy (Ministry of Agriculture and Rural Affairs), Biogas Institute of Ministry of Agriculture and Rural Affairs, Section 4-13, Renmin South Road, Chengdu 610041, PR China.
| | - Nipon Pisutpaisal
- The Research and Technology Center for Renewable Products and Energy, King Mongkut's University of Technology North Bangkok, Bangkok 10800, Thailand.
| | - Yan-Wei Wang
- Biomass Energy Technology Research Centre, Key Laboratory of Development and Application of Rural Renewable Energy (Ministry of Agriculture and Rural Affairs), Biogas Institute of Ministry of Agriculture and Rural Affairs, Section 4-13, Renmin South Road, Chengdu 610041, PR China.
| | - Ke-Dong Ma
- College of Environment and Resources, Dalian Minzu University, 18 Liaohe West Road, Dalian 116600, PR China
| | - Li-Chun Dai
- Biomass Energy Technology Research Centre, Key Laboratory of Development and Application of Rural Renewable Energy (Ministry of Agriculture and Rural Affairs), Biogas Institute of Ministry of Agriculture and Rural Affairs, Section 4-13, Renmin South Road, Chengdu 610041, PR China.
| | - Han Qin
- Biomass Energy Technology Research Centre, Key Laboratory of Development and Application of Rural Renewable Energy (Ministry of Agriculture and Rural Affairs), Biogas Institute of Ministry of Agriculture and Rural Affairs, Section 4-13, Renmin South Road, Chengdu 610041, PR China.
| | - Fu-Rong Tan
- Biomass Energy Technology Research Centre, Key Laboratory of Development and Application of Rural Renewable Energy (Ministry of Agriculture and Rural Affairs), Biogas Institute of Ministry of Agriculture and Rural Affairs, Section 4-13, Renmin South Road, Chengdu 610041, PR China.
| | - Toshinari Maeda
- Department of Biological Functions Engineering, Graduate School of Life Science and Systems Engineering, Kyushu Institute of Technology, 2-4 Hibikino,Wakamatsu, Kitakyushu 808-0196, Japan.
| | - Yan-Sheng Xu
- Biomass Energy Technology Research Centre, Key Laboratory of Development and Application of Rural Renewable Energy (Ministry of Agriculture and Rural Affairs), Biogas Institute of Ministry of Agriculture and Rural Affairs, Section 4-13, Renmin South Road, Chengdu 610041, PR China.
| | - Guo-Quan Hu
- Biomass Energy Technology Research Centre, Key Laboratory of Development and Application of Rural Renewable Energy (Ministry of Agriculture and Rural Affairs), Biogas Institute of Ministry of Agriculture and Rural Affairs, Section 4-13, Renmin South Road, Chengdu 610041, PR China.
| | - Ming-Xiong He
- Biomass Energy Technology Research Centre, Key Laboratory of Development and Application of Rural Renewable Energy (Ministry of Agriculture and Rural Affairs), Biogas Institute of Ministry of Agriculture and Rural Affairs, Section 4-13, Renmin South Road, Chengdu 610041, PR China; Chengdu National Agricultural Science and Technology Center, Chengdu, PR China.
| |
Collapse
|
41
|
Anjum A, Ali Mazari S, Hashmi Z, Sattar Jatoi A, Abro R. A review of role of cathodes in the performance of microbial fuel cells. J Electroanal Chem (Lausanne) 2021. [DOI: 10.1016/j.jelechem.2021.115673] [Citation(s) in RCA: 5] [Impact Index Per Article: 1.7] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 10/20/2022]
|
42
|
Cui MH, Liu WZ, Tang ZE, Cui D. Recent advancements in azo dye decolorization in bio-electrochemical systems (BESs): Insights into decolorization mechanism and practical application. WATER RESEARCH 2021; 203:117512. [PMID: 34384951 DOI: 10.1016/j.watres.2021.117512] [Citation(s) in RCA: 28] [Impact Index Per Article: 9.3] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 02/24/2021] [Revised: 06/22/2021] [Accepted: 07/27/2021] [Indexed: 06/13/2023]
Abstract
Recent advances in bio-electrochemical systems (BESs) for azo dye removal are gaining momentum due to having electrode biocarrier and electro-active bacteria that could stimulate decolorization via extracellular electron transfer. Enhanced decolorization performance is observed in most laboratory studies, indicating the great potential of BESs as an alternative to the traditional biological processes or serving as a pre-/post-processing unit to improve the performance of biological processes. It is proven more competitive in environmental friendly than physicochemical methods. While, the successful application of BESs to azo dye-containing wastewater remediation requires a deeper evaluation of its performance, mechanism and typical attributes, and a comprehensive potential evaluation of BESs practical application in terms of economic analysis and technical optimizations. This review is organized to address BESs as a practical option for azo dye removal by analyzing the decolorization mechanisms and involved functional microorganisms, followed by the comparisons of device configurations, operational conditions, and economic evaluation. It further highlights the current hurdles and prospects for the abatement of azo dyes via BES related techniques.
Collapse
Affiliation(s)
- Min-Hua Cui
- Jiangsu Key Laboratory of Anaerobic Biotechnology, Jiangnan University, Wuxi 214122, China
| | - Wen-Zong Liu
- School of Civil and Environmental Engineering, Harbin Institute of Technology (Shenzhen), Shenzhen 518055, China; State Key Laboratory of Urban Water Resource and Environment, Harbin Institute of Technology, Harbin, 150090, China; CAS Key Laboratory of Environmental Biotechnology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing, 100085, China
| | - Zi-En Tang
- National Engineering Laboratory for Advanced Municipal Wastewater Treatment and Reuse Technology, Beijing University of Technology, Beijing 100124, China
| | - Dan Cui
- National Engineering Laboratory for Advanced Municipal Wastewater Treatment and Reuse Technology, Beijing University of Technology, Beijing 100124, China.
| |
Collapse
|
43
|
Nagahashi W, Yoshida N. Comparative evaluation of fibrous artificial carbons and bamboo charcoal in terms of recovery of current from sewage wastewater. J GEN APPL MICROBIOL 2021; 67:248-255. [PMID: 34470976 DOI: 10.2323/jgam.2021.05.001] [Citation(s) in RCA: 4] [Impact Index Per Article: 1.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/03/2022]
Abstract
In this study, two fibrous carbon anodes (namely, pleated non-woven graphite (PNWG) and carbon brush (CB) made from artificial carbon) and bamboo charcoal (BC) were evaluated for current recovery from sewage wastewater. When these anodes were polarized at 0.2 V vs. Ag/AgCl in sewage wastewater, CB produced a maximum current of 2.9 A/m2. This exceeded that produced by PNWG (1.5 A/m2) and BC (1.4 A/m2). The accumulative charge recovery achieved with CB was superior to those achieved with the other two (1.6- and 2.2-fold higher than that with PNWG and BC, respectively). During the cyclic voltammetry analysis, CB demonstrated the highest catalytic current with maximum potential in the range of -0.6 to 0.4 V vs. Ag/AgCl and the smallest anode resistance (0.20 Ωm2). Direct cell counting revealed that the fibrous anodes (CB and PNWG) attached most of the cells in the anodes (80%), whereas BC did not. In contrast, the proportion of Geobacter species, a representative electrogenic microorganism in the total bacteria, was observed to be similar among the three anodes (4.4-5.8%). The tubular microbial fuel cell (ø 5.0 cm) equipped with an air-chamber core wrapped with an anion exchange membrane (AEM) and the CB delivered a current of 1.8 A/m2. This is higher than those reported in the existing literature for the same microbial fuel cell (MFC) configuration. This indicates that the alteration of the anode from planar to brush can contribute toward improving the current recovery through the air-cathode-AEM-MFC. The BC needs improvement to have more specific surface area, whereas it showed superiority in cost efficiency considering material and processing.
Collapse
Affiliation(s)
- Wataru Nagahashi
- Department of Civil and Environmental Engineering, Nagoya Institute of Technology (Nitech)
| | - Naoko Yoshida
- Department of Civil and Environmental Engineering, Nagoya Institute of Technology (Nitech)
| |
Collapse
|
44
|
Agricultural Waste and Wastewater as Feedstock for Bioelectricity Generation Using Microbial Fuel Cells: Recent Advances. FERMENTATION 2021. [DOI: 10.3390/fermentation7030169] [Citation(s) in RCA: 33] [Impact Index Per Article: 11.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/17/2022] Open
Abstract
In recent years, there has been a significant accumulation of waste in the environment, and it is expected that this accumulation may increase in the years to come. Waste disposal has massive effects on the environment and can cause serious environmental problems. Thus, the development of a waste treatment system is of major importance. Agro-industrial wastewater and waste residues are mainly rich in organic substances, lignocellulose, hemicellulose, lignin, and they have a relatively high amount of energy. As a result, an effective agro-waste treatment system has several benefits, including energy recovery and waste stabilization. To reduce the impact of the consumption of fossil energy sources on our planet, the exploitation of renewable sources has been relaunched. All over the world, efforts have been made to recover energy from agricultural waste, considering global energy security as the final goal. To attain this objective, several technologies and recovery methods have been developed in recent years. The microbial fuel cell (MFC) is one of them. This review describes the power generation using various types of agro-industrial wastewaters and agricultural residues utilizing MFC. It also highlights the techno-economics and lifecycle assessment of MFC, its commercialization, along with challenges.
Collapse
|
45
|
Syed Z, Sogani M, Dongre A, Kumar A, Sonu K, Sharma G, Gupta AB. Bioelectrochemical systems for environmental remediation of estrogens: A review and way forward. THE SCIENCE OF THE TOTAL ENVIRONMENT 2021; 780:146544. [PMID: 33770608 DOI: 10.1016/j.scitotenv.2021.146544] [Citation(s) in RCA: 8] [Impact Index Per Article: 2.7] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 10/18/2020] [Revised: 03/13/2021] [Accepted: 03/13/2021] [Indexed: 06/12/2023]
Abstract
Globally estrogenic pollutants are a cause of concern in wastewaters and water bodies because of their high endocrine disrupting activity leading to extremely negative impacts on humans and other organisms even at very low environmental concentrations. Bioremediation of estrogens has been studied extensively and one technology that has emerged with its promising capabilities is Bioelectrochemical Systems (BESs). Several studies in the past have investigated BESs applications for treatment of wastewaters containing toxic recalcitrant pollutants with a primary focus on improvement of performance of these systems for their deployment in real field applications. But the information is scattered and further the improvements are difficult to achieve for standalone BESs. This review critically examines the various existing treatment technologies for the effective estrogen degradation. The major focus of this paper is on the technological advancements for scaling up of these BESs for the real field applications along with their integration with the existing and conventional wastewater treatment systems. A detailed discussion on few selected microbial species having the unusual properties of heterotrophic nitrification and extraordinary stress response ability to toxic compounds and their degradation has been highlighted. Based on the in-depth study and analysis of BESs, microbes and possible benefits of various treatment methods for estrogen removal, we have proposed a sustainable Hybrid BES-centered treatment system for this purpose as a choice for wastewater treatment. We have also identified three pipeline tasks that reflect the vital parts of the life cycle of drugs and integrated treatment unit, as a way forward to foster bioeconomy along with an approach for sustainable wastewater treatment.
Collapse
Affiliation(s)
- Zainab Syed
- Department of Civil Engineering, Manipal University Jaipur, Jaipur 303007, Rajasthan, India; Department of Biosciences, Manipal University Jaipur, Jaipur 303007, Rajasthan, India
| | - Monika Sogani
- Department of Civil Engineering, Manipal University Jaipur, Jaipur 303007, Rajasthan, India; Department of Biosciences, Manipal University Jaipur, Jaipur 303007, Rajasthan, India.
| | - Aman Dongre
- Department of Civil Engineering, Manipal University Jaipur, Jaipur 303007, Rajasthan, India; Department of Biosciences, Manipal University Jaipur, Jaipur 303007, Rajasthan, India
| | - Anu Kumar
- Commonwealth Scientific and Industrial Research Organisation (CSIRO), L&W, Waite Campus, Urrbrae, SA, 5064, Australia.
| | - Kumar Sonu
- Department of Civil Engineering, Manipal University Jaipur, Jaipur 303007, Rajasthan, India
| | - Gopesh Sharma
- Department of Biosciences, Manipal University Jaipur, Jaipur 303007, Rajasthan, India
| | - Akhilendra Bhushan Gupta
- Department of Civil Engineering, Malaviya National Institute of Technology, Jaipur 302017, Rajasthan, India
| |
Collapse
|
46
|
Priyadarshini M, Ahmad A, Das S, Ghangrekar MM. Application of microbial electrochemical technologies for the treatment of petrochemical wastewater with concomitant valuable recovery: A review. ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH INTERNATIONAL 2021; 29:61783-61802. [PMID: 34231137 DOI: 10.1007/s11356-021-14944-w] [Citation(s) in RCA: 3] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 03/23/2021] [Accepted: 06/12/2021] [Indexed: 02/08/2023]
Abstract
Petrochemical industry is one of the major and rapidly growing industry that generates a variety of toxic and recalcitrant organic pollutants as by-products, which are not only harmful to the aquatic animals but also affects human health. The majority of the components of petrochemical wastewater (PW) are carcinogenic, genotoxic and phytotoxic in nature; hence, this complex wastewater generated from different petrochemical processes should be efficiently treated prior to its disposal in natural water bodies. The established technologies like advanced oxidation, membrane bioreactor, electrocoagulation and activated sludge process employed for the treatment of PW are highly energy intensive and incurs high capital and operation cost. Moreover, these technologies are not effective in completely eliminating petroleum hydrocarbons present in PW. Thus, to reduce the energy requirement and also to transform the chemical energy trapped in these organic matters present in this wastewater into bioelectricity and other value-added products, microbial electrochemical technologies (METs) can be efficaciously used, which would also compensate the treatment cost by transforming these pollutants into bioenergy and valuables. In this regard, this review elucidates the feasibility and application of different METs as an appropriate alternative for the treatment of PW. Furthermore, the numerous bottlenecks towards the real-life application and commercialization of pioneering METs have also been articulated.
Collapse
Affiliation(s)
- Monali Priyadarshini
- School of Environmental Science and Engineering, Indian Institute of Technology Kharagpur, Kharagpur, 721302, India
| | - Azhan Ahmad
- Department of Civil Engineering, Indian Institute of Technology Kharagpur, Kharagpur, 721302, India
| | - Sovik Das
- Department of Civil Engineering, Indian Institute of Technology Kharagpur, Kharagpur, 721302, India
| | - Makarand Madhao Ghangrekar
- School of Environmental Science and Engineering, Indian Institute of Technology Kharagpur, Kharagpur, 721302, India. .,Department of Civil Engineering, Indian Institute of Technology Kharagpur, Kharagpur, 721302, India.
| |
Collapse
|
47
|
Tabassum N, Islam N, Ahmed S. Progress in microbial fuel cells for sustainable management of industrial effluents. Process Biochem 2021. [DOI: 10.1016/j.procbio.2021.03.032] [Citation(s) in RCA: 16] [Impact Index Per Article: 5.3] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Indexed: 12/07/2022]
|
48
|
Yamane T, Yoshida N, Sugioka M. Estimation of total energy requirement for sewage treatment by a microbial fuel cell with a one-meter air-cathode assuming Michaelis-Menten COD degradation. RSC Adv 2021; 11:20036-20045. [PMID: 35479885 PMCID: PMC9033653 DOI: 10.1039/d1ra03061b] [Citation(s) in RCA: 10] [Impact Index Per Article: 3.3] [Reference Citation Analysis] [Abstract] [Grants] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/19/2021] [Accepted: 05/30/2021] [Indexed: 12/18/2022] Open
Abstract
Calculations of chemical oxygen demand (COD) degradation in sewage by a microbial fuel cell (MFC) were used to estimate the total energy required for treatment of the sewage. Mono-exponential regression (MER) and the Michaelis-Menten equation (MME) were used to describe the MFC's COD removal rate (CRR). The tubular MFC used in this study (ϕ 5.0 × 100 cm) consisted of an air core surrounding a carbon-based cathode, an anion exchange membrane, and graphite non-woven fabric immersed in sewage. The MFC generated 0.26 A m-2 of the electrode area and 0.32 W m-3 of the sewage water, and 3.9 W h m-3 in a chemostat reactor supplemented continuously with sewage containing 180 mg L-1 of COD with a hydraulic retention time (HRT) of 12 h. The COD removal and coulombic efficiency (CE) were 46% and 19%, respectively, and the energy generation efficiency (EGE) was 0.054 kW h kg-1-COD. The CRR and current in the MFC were strongly dependent on the COD, which could be controlled by varying the HRT. The MER model predicted first-order rate constants of 0.054 and 0.034 for reactors with and without MFC, respectively. The difference in these values indicated that using MFC significantly increased the COD removal. The results of fitting the experimental data to the MME suggested that the total COD can be separated into nondegradable CODs (C n) and degradable CODs (C d) via MFC. The values of CRR for C d and CE suggest that MFC pretreatment for 12 hours prior to aeration results in a 75% decrease in net energy consumption while reducing sewage COD from 180 to 20 mg L-1.
Collapse
Affiliation(s)
- Taiki Yamane
- Department of Civil and Environmental Engineering, Nagoya Institute of Technology (Nitech) Gokiso-Cho, Showa-Ku Nagoya Aichi Japan
| | - Naoko Yoshida
- Department of Civil and Environmental Engineering, Nagoya Institute of Technology (Nitech) Gokiso-Cho, Showa-Ku Nagoya Aichi Japan
| | - Mari Sugioka
- Department of Civil and Environmental Engineering, Nagoya Institute of Technology (Nitech) Gokiso-Cho, Showa-Ku Nagoya Aichi Japan
| |
Collapse
|
49
|
Li ZL, Zhu ZL, Lin XQ, Chen F, Li X, Liang B, Huang C, Zhang YM, Sun K, Zhou AN, Wang AJ. Microbial fuel cell-upflow biofilter coupling system for deep denitrification and power recovery: Efficiencies, bacterial succession and interactions. ENVIRONMENTAL RESEARCH 2021; 196:110331. [PMID: 33068576 DOI: 10.1016/j.envres.2020.110331] [Citation(s) in RCA: 14] [Impact Index Per Article: 4.7] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 06/06/2020] [Revised: 08/26/2020] [Accepted: 10/09/2020] [Indexed: 06/11/2023]
Abstract
The excess organic carbon is often added to meet denitrification requirements during municipal wastewater treatment, resulting in the carbon waste and increased risk of secondary pollution. In this study, microbial fuel cell (MFC) was coupled with an up-flow denitrification biofilter (BF), and the long-term performances of denitrification and power output were investigated under the different carbon source concentration. With sodium acetate (NaAc) of 600 mg/L and 300 mg/L, the favorable denitrification efficiencies were obtained (98.60%) and the stable current output was maintained (0.44 mÃ0.48 mA). By supplying NaAc of 150 mg/L, the high denitrification efficiency remained in a high range (89.31%) and the current output maintained at 0.12 mA, while, the denitrification efficiency dropped to 71.34% without coupling MFC. Electron balance analysis indicated that both nitrate removal and electron recovery efficiencies were higher in MFC-BF than that in BF, verifying the improved denitrification and carbon utilization performance. Coupling MFC significantly altered the bacterial community structure and composition, and while, the diversified abundance and distribution of bacterial genera were observed at the different locations. Compared with BF, the more exoelectrogenic genera (Desulfobacterium, Trichococcus) and genera holding both denitrifying and electrogenic functions (Dechloromonas, Geobacter) were found dominated in MFC-BF. Instead, the dominating genera in BF were Dechloromonas, Desulfomicrobium, Acidovorax and etc. By coupling MFC, the more complex and diversified network and the closer interaction relationships between the dominant potential functional genera were found. The study provides a feasible approach to effectively improve the denitrification efficiency and organic carbon recovery for deep denitrification process.
Collapse
Affiliation(s)
- Zhi-Ling Li
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, Harbin, 150090, China
| | - Zhong-Li Zhu
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, Harbin, 150090, China
| | - Xiao-Qiu Lin
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, Harbin, 150090, China
| | - Fan Chen
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, Harbin, 150090, China
| | - Xu Li
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, Harbin, 150090, China
| | - Bin Liang
- Key Laboratory of Environmental Biotechnology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing, 100085, China
| | - Cong Huang
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, Harbin, 150090, China
| | - Yuan-Ming Zhang
- Key Lab of Structures Dynamic Behavior and Control of China Ministry of Education, School of Civil Engineering, Harbin Institute of Technology, Harbin, 150090, China
| | - Kai Sun
- Key Lab of Structures Dynamic Behavior and Control of China Ministry of Education, School of Civil Engineering, Harbin Institute of Technology, Harbin, 150090, China.
| | - An-Nan Zhou
- Civil and Infrastructure Engineering, School of Engineering, RMIT University, Melbourne, Vic, 3001, Australia
| | - Ai-Jie Wang
- State Key Laboratory of Urban Water Resource and Environment, School of Environment, Harbin Institute of Technology, Harbin, 150090, China; Key Laboratory of Environmental Biotechnology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing, 100085, China.
| |
Collapse
|
50
|
Removal of Antibiotics and Nutrients by Vetiver Grass ( Chrysopogon zizanioides) from a Plug Flow Reactor Based Constructed Wetland Model. TOXICS 2021; 9:toxics9040084. [PMID: 33921009 PMCID: PMC8071396 DOI: 10.3390/toxics9040084] [Citation(s) in RCA: 4] [Impact Index Per Article: 1.3] [Reference Citation Analysis] [Abstract] [Key Words] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 03/10/2021] [Revised: 04/09/2021] [Accepted: 04/13/2021] [Indexed: 11/29/2022]
Abstract
Overuse of antibiotics has resulted in widespread contamination of the environment and triggered antibiotic resistance in pathogenic bacteria. Conventional wastewater treatment plants (WWTPs) are not equipped to remove antibiotics. Effluents from WWTPs are usually the primary source of antibiotics in aquatic environments. There is an urgent need for cost-effective, environment-friendly technologies to address this issue. Along with antibiotics, nutrients (nitrogen and phosphorus) are also present in conventional WWTP effluents at high concentrations, causing environmental problems like eutrophication. In this study, we tested vetiver grass in a plug flow reactor-based constructed wetland model in a greenhouse setup for removing antibiotics ciprofloxacin (CIP) and tetracycline (TTC), and nutrients, N and P, from secondary wastewater effluent. The constructed wetland was designed based on a previous batch reaction kinetics study and reached a steady-state in 7 days. The measured concentrations of antibiotics were generally consistent with the modeling predictions using first-order reaction kinetics. Vetiver grass significantly (p < 0.05) removed 93% and 97% of CIP and TTC (initial concentrations of 10 mg/L), simultaneously with 93% and 84% nitrogen and phosphorus, respectively. Results show that using vetiver grass in constructed wetlands could be a viable green technology for the removal of antibiotics and nutrients from wastewater.
Collapse
|