Effect of water quality on the yield and quality of the products from hydrothermal liquefaction and carbonization of rice straw

Hydrothermal liquefaction: Exploring biomass/plastic synergies and pathways for enhanced biofuel production

The worsening environmental conditions, diminishing fossil fuel reserves, and increasing waste accumulation have redirected the attention of researchers and scientists towards the exploration of sustainable and non-exhaustive energy sources, as well as waste mitigation techniques. Among the various thermochemical technologies producing biofuels, hydrothermal liquefaction stands out as an effective technique for the simultaneous waste valorization and the production of sustainable biofuels. Under optimal conditions, hydrothermal liquefaction converts 70-80 % of feedstock energy into bio-oil, representing approximately 30-50 % of the feedstock's original mass. The review meticulously discusses and summarizes the process and reaction mechanism along with the influence of various factors on the hydrothermal liquefaction process, including the types of feedstocks (lignocellulosic biomass and plastic waste), operating conditions (temperature, residence time, pressure, substrate-to-water ratio, particle size, and heating rate), and catalyst types. According to the data documented in existing literature, the preferred temperature and residence time for attaining maximum bio-oil yields are reported to be within the range of 260-340 °C and 10-30 min for biomass, and 300-425 °C and 15-30 min for plastics. This review highlights the critical challenges in developing and scaling up the HTL process, proposing potential solutions to enhance feedstock conversion into value-added products. Additionally, it emphasizes the significance of understanding the chemical composition and synergistic interactions between lignocellulosic biomass and plastic waste to optimize product yields and enhance the overall process efficiency. Moreover, it discusses the different products of the hydrothermal liquefaction process-bio-oil, biochar, aqueous phase, and gaseous fraction-and their potential applications, while proposing techniques to upgrade the quality of biocrude.

A study on value addition of cow dung-based anaerobic sludge for biomethane and bio-oil production via co-liquefaction with rice straw and clam shells as a catalyst

The waste management sector is moving towards sustainable approaches for facilitating resource-recovery possibilities. Agriculture residue (rice straw), cow dung (cattle waste), and clam shells from the ocean are the primary waste materials possessing a huge value addition opportunity. In this study, the effective usage of rice straw and anaerobic sludge from cow dung for bio-energy production was studied. Cow dung was initially anaerobically processed for the generation of biomethane and sludge in a digester for a retention time of 40 days. The anaerobic sludge with rice straw was hydrothermally processed in varying proportions of 1 : 0, 0 : 1, 1 : 1,1 : 2, 2 : 1, 3 : 1, 1 : 3 and temperatures of 240-360 °C for 1 hour with varying biomass loads of 50, 75, 100, 125, and 150 g. Additionally, clam shells, one of the best bioresources, were used as a catalyst in the hydrothermal process at concentrations of 0.2-1 wt%. The maximum bio-oil produced was 36.23 wt% at a temperature of 320 °C, with a biomass load of 100 g, mixed proportion of 2 : 1 and catalyst loading of 0.6 wt%. The produced bio-oil comprised hydrocarbons, aldehydes, and carboxylic acids, as confirmed through GC-MS. In the anaerobic study, ≈0.018 m3 cumulative gas was produced at a retention time of 40 days. The biochar had a higher carbon content and its feasibility for further usage shows promise towards sustainability.

Lignocellulosic biomass for biochar production: A green initiative on biowaste conversion for pharmaceutical and other emerging pollutant removal

Lignocellulosic waste generation and their improper disposal has accelerated the problems associated with increased greenhouse gas emissions and associated environmental pollution. Constructive ways to manage and mitigate the pollution associated with lignocellulosic waste has propelled the research on biochar production using lignocellulose-based substrates. The sustainability of various biochar production technologies in employing lignocellulosic biomass as feedstock for biochar production not only aids in the lignocellulosic biomass valorization but also helps in carbon neutralization and carbon utilization. Functionalization of biochar through various physicochemical methods helps in improving their functional properties majorly by reducing the size of the biochar particles to nanoscale and modifying their surface properties. The usage of engineered biochar as nano adsorbents for environmental applications like dye absorption, removal of organic pollutants and endocrine disrupting compounds from wastewater has been the thrust areas of research in the past few decades. This review presents a comprehensive outlook on the up-to-date research findings related to the production and engineering of biochar from lignocellulosic biomass and their applications in environmental remediation especially with respect to wastewater treatment. Further a detailed discussion on various biochar activation methods and the future scope of biochar research is presented in this review work.

Distribution characteristics and migration pathways of metals during hydrothermal liquefaction of municipal sewage sludge in the presence of various catalysts

A series of hydrothermal liquefaction (HTL) experiments with two different samples of municipal sewage sludge (MSS) were conducted at 350 °C for 30 min residence time in a high pressure batch reactor. The main aim of the study was to explore the distribution and migration pathways of a broad range of metals and metalloids in the HTL products (bio-oil, char and aqueous phase) obtained in the presence of various homogeneous and heterogeneous catalysts (Na2CO3, Li2CO3, K2CO3, Ba(OH)2, Fe2O3, CeO2, NiMo/MoO3, MoS2, Ni/NiO, SnO2, FeS). The elements under study included 16 environmentally significant metals and metalloids (As, B, Ba, Cd, Co, Cr, Cu, Mn, Mo, Ni, Pb, Sb, Se, Sn, Zn and Hg). The study showed that the quantitative migration of the tested metals and metalloids to the particular HTL products, relative to their initial content in the raw sludge, is different for the individual elements. Most metals exhibited a particularly strong affinity to the solid fraction (biochar). In the obtained HTL bio-oils, all tested elements were identified, except of Cd. It was also found that B and As have high affinity to the aqueous phase. A direct effect of catalysts on the contents of some elements in the products was also proved by the study, e.g. increased concentration of Cr in the biochar when Fe2O3 was used as a process catalyst. Due to the wide scope of the tested elements and broad range of catalyst used, the results obtained represent a unique and comprehensive set of environmental data compared to similar HTL studies previously conducted for MSS.

Utilization of solid residue from hydrothermal liquefaction of breadfruit pulp for the production of bio-briquette using cassava starch as binder

The generation of agro-waste as a result of increase in agro and food processing activities is on the increase due to rapid increase in human population. Hence the need to eliminate these waste by converting them into a useful product or energy source. This work presents the use of bio-char from hydrothermal liquefaction of breadfruit pulp to produce bio-briquettes with cassava starch as a binder. The response surface method using design expert was used to design the experiment with particle size, press pressure and binder dosage as factors, to determine the parameter combination that will produce briquettes of high energy density. The briquette with the highest calorific value 26.75 MJ/kg was produced at the parameter combination of 450 mm-6 particle size, 5 MPa press pressure, and 20 % binder dosage. The ultimate analysis carried on the produced briquette gave carbon, hydrogen, nitrogen and sulphur content of 47.22 %, 3.88 %, 0.69 %, and 0.42 % respectively, with oxygen content of 4.79 % by percentage mass difference. While the proximate analysis gave moisture, ash, volatile matter, and fixed carbon content of 7.8 %, 3.9 %, 43.7 %, and 44.6 % respectively. Other characterization test carried out gave combustion rate of 4.5 g/min, ignition time of 3.5 min, density of 0.86 g/cm3, compressive strength of 8.31 N/mm2, shatter index of 0.89, and hydrophobicity of 61.3 %. These findings shows that briquettes produced with bio-char from HTL of breadfruit pulp can be used as solid fuel for domestic and mini-industrial heating purposes, as well as eliminate waste from processing of breadfruit.

Simultaneous nitrate and phosphorus removal in novel steel slag biofilters: Optimization and mechanism study

The simultaneous nitrate (NO3--N) and phosphorus (P) removal systems are considered to be an effective wastewater treatment technology. However, so far, there are few studies on system optimization to improve NO3--N and P removal. In this study, nine simultaneous NO3--N and P removal biofilters (SNPBs) were constructed to treat simulated wastewater. In order to optimize the NO3--N and P removal, different material loading positions were set: (1) red soil, steel slag, and rice straw (RSR), (2) steel slag, red soil, and rice straw (SRR), and (3) red soil, rice straw, and steel slag (RRS). Results showed that the above three treatments had mean removal efficiencies of 58%-91% for NO3--N and 55%-81% for TP, with the best N and P removal occurring in the SRR. The TN mass balance indicated that microbial removal was responsible for 78.2% of the influent TN in the SRR biofilter. The key microorganisms were Enterobacter, Klebsiella, Pseudomonas, Diaphorobacter, and unclassified_f_Enterobacteriaceae, which accounted for 61.9% of the total microorganisms. The main P-removal mechanism was the formation of Al-P, Fe-P, and Ca-P in red soil or steel slag layer. In addition, the decrease of SRR effluent pH from 11.86 in 1-7 days to 7.75 in 8-50 days indicated that red soil and rice straw had a synergistic effect on water pH reduction. These results suggest that a reasonable combination of steel slag with red soil and rice straw not only simultaneously removes NO3--N and P but also additionally solves the problem of high pH caused by steel slag.

Seawater as supplemental moisture: The effect of Co-hydrothermal carbonization products obtained from chicken manure and cornstalk

The use of seawater as a substitute for pure water as supplemental moisture raises questions about its effect on the physicochemical properties of hydrochar. Therefore, this study aimed to investigate the feasibility of using seawater as supplemental moisture by comparing the physicochemical properties of products obtained through Co-hydrothermal carbonization of chicken manure and cornstalk under seawater and deionized water conditions. By varying the HTC temperature and blending ratios of CM and CS to investigate comprehensively the effect of seawater. Results indicated that the hydrochar yield experienced a variation from 54.54% to 57.40%, while the IC value changed from 7.69% to 8.46% as the ratio of CM:CS shifted from 3:1 to 1:3 under seawater conditions. The higher heating value of the hydrochars obtained under seawater conditions was lower than those obtained under deionized water conditions. This suggests that seawater conditions promote the hydrolysis reaction of organic solid waste. Furthermore, it was observed that when no lignin hydrolysis reaction occurred, seawater conditions had no discernible effect on the fuel quality of the hydrochar. However, at an HTC temperature of 250 °C, the fuel quality of the hydrochar obtained under seawater conditions was notably inferior to that of the hydrochar obtained under deionized water. Thus, an HTC temperature lower than 250 °C is necessary for the hydrothermal carbonization of organic solid waste under seawater conditions. Moreover, the relative content of surface -C-(C, H)/CC of the hydrochar obtained under seawater conditions was lower than that obtained under deionized water conditions, indicating that the hydrochar had a low degree of aromatization. Additionally, there was a significant increase in the immobilized Mg atoms in the hydrochar under seawater conditions, which affected the hydrochar yield and higher heating value of the hydrochar. This research presents a theoretical foundation for preparing solid fuels and materials using hydrothermal carbonization of saltwater as supplemental moisture.

Directional regulation and mechanism analysis of the surface properties of hydrothermal carbon by circulating liquid in the hydrothermal carbonization procedure

The complexity of the chemistry behind the hydrothermal conversion is enormous. Components interact with their own physical and chemical structure, making it harsh to understand the conversion as a whole. Herein, the six-water recirculation and loading nano SiO₂ experiment in a one-pot hydrothermal carbonization procedure was designed to elucidate the mechanism of regulating the functional groups and microporous structure of the hydrochar surface. The hydrochar prepared by the second circulating liquid and loading nano-SiO₂ (HBC-R2/Si) was equipped most enriched functional groups (carboxyl = 11.48 μmol/g, phenolic hydroxyl = 52.98 μmol/g, lactone groups = 46.52 μmol/g) and suitable pore size (1.90 nm-1.93 nm) as a sorbent riched in hemicellulose. The sorption kinetics (equilibrium reached ≈ 480 min) are approximately evenly fitted by the pseudo-second-order, Weber and Morris, and Elovich models, indicating that membranes and particles diffusion, pore diffusion, and surface sorption coexisted in the sorption of methylene blue (MB) on the hydrochar materials. Simultaneously, all hydrochar materials achieved over 25% MB removal within 90 min (liquid membrane diffusion) and over 40% for HBC-R2 and HBC-R2/Si, suggesting that liquid membrane diffusion is the predominant rate-limiting step. Pearson's correlation analysis and Mantel's analysis announced that the cation exchange capacity (CEC), pore size, and carboxyl groups on the hemicellulose affect the sorption capacity by limiting the pore diffusion procedure. However, the CEC and the phenolic hydroxyl groups on the cellulose and hemicellulose affect the sorption rate by limiting membrane diffusion. Three consecutive sorption/desorption cycles confirmed the high stability and reusability of HBC-R2/Si composites.

Production of biochar from rice straw and its application for wastewater remediation - An overview

The valorization of biochar as a green and low-cost adsorbent provides a sustainable alternative to commercial wastewater treatment technologies that are usually chemical intensive and expensive. This review presents an in-depth analysis focusing on the rice straw-derived biochar (RSB) for removal of various types of contaminants in wastewater remediation. Pyrolysis is to date the most established technology to produce biochar. Subsequently, biochar is upgraded via physical, chemical or hybrid activation/modification techniques to enhance its adsorption capacity and robustness. Thus far, acid-modified RSB is able to remove metal ions and organic compounds, while magnetic biochar and electrochemical deposition have emerged as potential biochar modification techniques. Besides, temperature and pH are the two main parameters that affect the efficiency of contaminants removal by RSB. Lastly, the limitations of RSB in wastewater remediation are elucidated based on the current advancements of the field, and future research directions are proposed.

Exploring agricultural waste biomass for energy, food and feed production and pollution mitigation: A review

Globally agricultural production system generates a huge amount of solid waste. Improper agri-waste management causes environmental pollution which resulted in economic losses and human health-related problems. Hence, there is an urgent need to design and develop eco-friendly, cost-effective, and socially acceptable agri-waste management technologies. Agri-waste has high energy conversion efficiency as compared to fossil fuel-based energy generation materials. Agri-waste can potentially be exploited for the production of second-generation biofuels. However, composted agri-waste can be an alternative to energy-intensive chemical fertilizers in organic production systems. Furthermore, value-added agri-waste can be a potential feedstock for livestock and industrial products. But comprehensive information concerning agri-waste management is lacking in the literature. Therefore, the present study reviewed the latest advancements in efficient agri-waste management technologies. This latest review will help the researchers and policy planners to formulate environmentally robust residue management practices for achieving a green economy in the agricultural production sector.