Unravelling the biodegradation performance and mechanisms of acid orange 7 by aerobic granular sludge at different salinity levels

Single and combined treatment processes for rhodamine B removal by coagulation-flocculation and adsorption

In this paper, two physico-chemical methods were adopted for the removal of rhodamine B from aqueous solutions. The first one is the adsorption process using biochar derived from olive stones (OSB). Results demonstrated that the removal efficiency reached 97.79% within an equilibrium time of one hour. It was observed that the pH had no significant effect on the degradation of rhodamine B by OSB. The adsorption process was characterized by the endothermic nature, spontaneity, favorability, and disorder at the solid-liquid interface. Langmuir isotherm analysis revealed a maximum adsorption capacity of 11.82 mg g-1, and the prepared biochar could be reused for up to four cycles. For the second method, coagulation-flocculation using FeCl3 as a coagulant was investigated. The findings displayed that an increase in the dosage of FeCl3 enhanced the degradation process, with the best performance registered at a dose of 2000 mg L-1 of FeCl3. The optimum pH for this process was found to be 2. A combination approach by these two methods, starting with coagulation-flocculation and followed by adsorption, was also investigated. The results showed that the combined approach improved the removal performance compared to each process alone, with minimal doses of both coagulant and adsorbent. Thus, the combination of these two physico-chemical processes allows benefits from the advantages and reduces the disadvantages of each individual method.

Mechanisms underlying the detrimental impact of micro(nano)plastics on the stability of aerobic granular sludge: Interactions between micro(nano)plastics and extracellular polymeric substances

Microplastics (MPs) and nanoplastics (NPs) present in wastewater can pose a negative impact to aerobic granular sludge (AGS). Herein, this study found that MPs and NPs (20 mg/L) deteriorated the sludge settleability and granule integrity, resulting in a 15.7 % and 21.9 % decrease in the total nitrogen removal efficiency of the AGS system, respectively. This was possibly due to the reduction of the extracellular polymeric substances (EPS) content. The subsequent analysis revealed that tyrosine, tryptophan, and humic acid-like substances in EPS exhibited a higher propensity for chemisorption and inhomogeneous multilayer adsorption onto NPs compared to MPs. The binding of EPS onto the surface of plastic particles increased the electronegativity of the MPs, but facilitated the aggregation of NPs through reducing the electrostatic repulsion, thereby mitigating the adverse effects of MPs/NPs on the AGS stability. Additionally, comprehensive analysis of the extended Derjaguin-Landau-Verwey-Overbeek theory indicated that the suppressed aggregation of microorganisms was the internal mechanisms contributing to the inadequate stability of AGS induced by MPs/NPs. This study provides novel insights into the detrimental mechanisms of MPs/NPs on the AGS stability, highlighting the key role of EPS in maintaining the structural stability of AGS when exposed to MPs/NPs.

Frequency-modulated alternating current-driven bioelectrodes for enhanced mineralization of Alizarin Yellow R

The alternating current (AC)-driven bioelectrochemical process, in-situ coupling cathodic reduction and anodic oxidation in a single electrode, offers a promising way for the mineralization of refractory aromatic pollutants (RAPs). Frequency modulation is vital for aligning reduction and oxidation phases in AC-driven bioelectrodes, potentially enhancing their capability to mineralize RAPs. Herein, a frequency-modulated AC-driven bioelectrode was developed to enhance RAP mineralization, exemplified by the degradation of Alizarin Yellow R (AYR). Optimal performance was achieved at a frequency of 1.67 mHz, resulting in the highest efficiency for AYR decolorization and subsequent mineralization of intermediates. Performance declined at both higher (3.33 and 8.30 mHz) and lower (0.83 mHz) frequencies. The bioelectrode exhibited superior electron utilization, bidirectional electron transfer, and redox bifunctionality, effectively aligning reduction and oxidation processes to enhance AYR mineralization. The 1.67 mHz frequency facilitated the assembly of a collaborative microbiome dedicated to AYR bio-mineralization, characterized by an increased abundance of functional consortia proficient in azo dye reduction (e.g., Stenotrophomonas and Shinella), aromatic intermediates oxidation (e.g., Sphingopyxis and Sphingomonas), and electron transfer (e.g., Geobacter and Pseudomonas). This study reveals the role of frequency modulation in AC-driven bioelectrodes for enhanced RAP mineralization, offering a novel and sustainable approach for treating RAP-bearing wastewater.

Henna plant biomass enhanced azo dye removal: Operating performance, microbial community and machine learning modeling

The bio-reduction of azo dyes is significantly dependent on the availability of electron donors and external redox mediators. In this study, the natural henna plant biomass was supplemented to promote the biological reduction of an azo dye of Acid Orange 7 (AO7). Besides, the machine learning (ML) approach was applied to decipher the intricate process of henna-assisted azo dye removal. The experimental results indicated that the hydrolysis and fermentation of henna plant biomass provided both electron donors such as volatile fatty acid (VFA) and redox mediator of lawsone to drive the bio-reduction of AO7 to sulfanilic acid (SA). The high henna dosage selectively enriched certain bacteria, such as Firmicutes phylum, Levilinea and Paludibacter genera, functioning in both the henna fermentation and AO7 reduction processes simultaneously. Among the three tested ML algorithms, eXtreme Gradient Boosting (XGBoost) presented exceptional accuracy and generalization ability in predicting the effluent AO7 concentrations with pH, oxidation-reduction potential (ORP), soluble chemical oxygen demand (SCOD), VFA, lawsone, henna dosage, and cumulative henna as input variables. The validating experiments with tailored optimal operating conditions and henna dosage (pH 7.5, henna dosage of 2 g/L, and cumulative henna of 14 g/L) confirmed that XGBoost was an effective ML model to predict the efficient AO7 removal (91.6%), with a negligible calculating error of 3.95%. Overall, henna plant biomass addition was a cost-effective and robust method to improve the bio-reduction of AO7, which had been demonstrated by long-term operation, ML modeling, and experimental validation.

Microbial communities drive flux of acid orange 7 and crystal violet dyes in water-sediment system

Unchecked dye effluent discharge poses escalating environmental and economic concerns, especially in developing nations. While dyes are well-recognized water pollutants, the mechanisms of their environmental spread are least understood. Therefore, the present study examines the partitioning of Acid Orange 7 (AO7) and Crystal Violet (CV) dyes using water-sediment microcosms and reports that native microbes significantly affect AO7 decolorization and transfer. Both dyes transition from infused to pristine matrices, reaching equilibrium in a fortnight. While microbes influence CV partitioning, their role in decolorization is minimal, emphasizing their varied impact on the environmental fate of dyes. Metagenomic analyses reveal contrasting microbial composition between control and AO7-infused samples. Control water samples displayed a dominance of Proteobacteria (62%), Firmicutes (24%), and Bacteroidetes (9%). However, AO7 exposure led to Proteobacteria reducing to 57% and Bacteroidetes to 3%, with Firmicutes increasing to 34%. Sediment samples, primarily comprising Firmicutes (47%) and Proteobacteria (39%), shifted post-AO7 exposure: Proteobacteria increased to 53%, and Firmicutes dropped to 38%. At the genus level, water samples dominated by Niveispirillum (34%) declined after AO7 exposure, while Bacillus and Pseudomonas increased. Notably, Serratia and Sphingomonas, known for azo dye degradation, rose post-exposure, hinting at their role in AO7 decolorization. Conversely, sediment samples showed a decrease in the growth of Bacillus and an increase in that of Pseudomonas and Serratia. These findings emphasize the significant role of microbial communities in determining the environmental fate of dyes, providing insights on its environmental implications and management.

When aerobic granular sludge faces emerging contaminants: A review

The evolution of emerging contaminants (ECs) has caused greater requirements and challenges to the current biological wastewater treatment technology. As one of the most promising biological treatment technologies, the aerobic granular sludge (AGS) process also faces the challenge of ECs. This study summarizes the recent progress and characteristics of several representative ECs (persistent organic pollutants, endocrine disrupting chemicals, antibiotics, and microplastics) in AGS systems that have garnered widespread attention. Additionally, the biodegradation and adsorption mechanisms of ECs were discussed, and the interactions between various ECs and AGS was elucidated. The importance of extracellular polymeric substances for the stabilization of AGS and the removal of ECs is also discussed. Knowledge gaps and future research directions that may enable the practical application of AGS are highlighted. Overall, AGS processes show great application potential and this review provides guidance for the future implementation of AGS technology as well as elucidating the mechanism of its interaction with ECs.

Evolution of aniline degradation and nitrogen removal performance in electro-enhanced sequence batch reactor under salinity stress: Sludge characteristics and microbial diversity

To explore the influence mechanism of different concentrations of salinity on the electro-enhanced aniline biodegradation system, a control group and experimental groups (0%-NaCl, 0.5%-NaCl, 1.5%-NaCl, 2.5%-NaCl, 3.5%-NaCl) were established. The experimental results showed that the electric field strengthened the denitrification performance, while salinity had little effect on the degradation efficiency of aniline and chemical oxygen demand (COD). The removal rate of TN reached 79.6% and 74.9% in 0.5%-NaCl and 1.5%-NaCl, respectively, which were superior than 0%-NaCl. As salinity increased, the nitrogen removal effect was negatively affected. Microbial diversity analysis indicated that the microbial community structure was uniform in the control group, 0%-NaCl, and 0.5%-NaCl, with the dominant genus OLB8 ensuring the nitrogen removal performance. In contrast, in the 2.5%-NaCl and 3.5%-NaCl experimental groups, the organic degrading bacteria were still active, while nitrifiers and denitrifiers were severely damaged. In conclusion, this study suggested that low concentrations of salinity can improve the decontamination performance of the electro-enhanced aniline biodegradation system, while high concentrations of salinity could lead to the collapse of the decontamination mechanism.

Impact of zero-valent iron on nitrifying granular sludge for 17α-ethinylestradiol removal and its mechanism

Aerobic granulation of nitrifying activated sludge could enhance the removal of 17α-ethinylestradiol (EE2) via abiotic nitration induced by reactive nitrogen species, cometabolism by ammonia-oxidizing bacteria and biodegradation by heterotrophic bacteria. Zero-valent iron (ZVI), a promising and low-cost material, has previously been applied to effectively enhance biological wastewater treatment. The impact and the effect mechanism of ZVI on nitrifying granular sludge (NGS) for EE2 removal was investigated in this study. The results showed that the addition of ZVI achieved better EE2 removal, though ZVI was not conducive to the accumulation of nitrite in NGS which reduced the abiotic transformation of EE2. Moreover, ZVI enriched heterotrophic denitrifying bacteria such as Arenimonas, thus changing the EE2 removal pathway and improving the degradation and mineralization of EE2. In addition, ZVI reduced the emission risk of the greenhouse gas N₂O and strengthened the stability of the granules. Metagenomic analysis further revealed that the functional genes related to EE2 mineralization, nitrite oxidation, N₂O reduction and quorum sensing in NGS were enriched with ZVI addition. This study provides meaningful guidance for ZVI application in the NGS process to achieve efficient and simultaneous removal of ammonia and emerging contaminants.

Low salinity enhances azo dyes degradation in aerobic granular sludge systems: Performance and mechanism analysis

The biodegradation performance of azo dyes can be enhanced under low salinity conditions, but the internal biodegradation mechanism is still unclear. Aerobic granular sludge (AGS), a salt-tolerant biological wastewater treatment technology, was used in this study to explore the enhancement mechanism of acid orange 7 (AO7) degradation at low salinity level (1.0 %). Results indicated that the AGS structure and reactor performance were almost unaffected by different AO7 concentrations (5-10 mg/L). Compared with salt-free conditions, the AO7 removal efficiency was elevated by 9.9 %-19.0 % at 1.0 % salinity level, owing to the enrichment of AO7 decolorizing bacteria (e.g. Acinetobacter) and functional enzymes (e.g. FMN-dependent azoreductase). The up-regulated genes involving in the key metabolic functions (e.g. carbon metabolism and oxidative phosphorylation) promoted the electron and energy production, thereby facilitating the AO7 decolorization and degradation. These results aid understanding of the enhancement mechanism of AO7 biodegradation under low salinity conditions from macroscopic and microscopic perspectives.

An overview of deploying membrane bioreactors in saline wastewater treatment from perspectives of microbial and treatment performance

The discharged saline wastewater has severely influenced the aquatic environment as the treatment performance of many wastewater treatment techniques is limited. In addition, the sources of saline wastewater are also plentiful from agricultural and various industrial fields such as food processing, tannery, pharmaceutical, etc. Although high salinity levels negatively impact the performance of both physicochemical and biological processes, membrane bioreactor (MBR) processes are considered as a potential technology to treat saline wastewater under different salinity levels depending on the adaption of the microbial community. Therefore, this study aims to systematically review the application of MBR widely used in the saline wastewater treatment from the perspectives of microbial structure and treatment efficiencies. At last, the concept of carbon dioxide capture and storage will be proposed for the MBR-treating saline wastewater technologies and considered toward the circular economy with the target of zero emission.

Metagenomics unraveled the characteristics and microbial response to hypersaline stress in salt-tolerant aerobic granular sludge

In this study, the salt-tolerant aerobic granular sludge (SAGS) was cultivated with the increased salinity (0-9% NaCl), showing oval shape, and clear outline. The related sludge characteristics in the formation process of SAGS as well as the effects of salinity on the performance (removal ability, sludge biomass and EPS component) of SAGS were evaluated. Increased salinity accelerated the formation of SAGS, and resulted in the excess secretion of EPS. Relationship between EPS and settling capacity of SAGS was determined, with the increase of salinity, SVI decreased linearly and the sedimentation performance of granular sludge was enhanced. Pearson correlation analysis showed that shorter settling time (3 min) and longer anaerobic influent time (30 min) were beneficial to the operation of SAGS reactor. Metagenomics results showed that the SAGS was dominated by Candida, Halomonas and other salt-tolerant bacteria, the enrichment of these salt-tolerant microbes played an important role in maintaining the stability of granular sludge system and improving the overall salt-tolerant performance. Compared with S9 samples, the proteome regulation in S0 sample was more active and the abundance of Cell motility related proteins was 5 times higher than that in S9 samples. Extracellular structure related proteins was more active in S9, and its abundance was 3.6 times that of S0.