A thionine-modified carbon paste amperometric biosensor for catechol and bisphenol A determination

Disposable biosensor based on nanodiamond particles, ionic liquid and poly-l-lysine for determination of phenolic compounds

This study describes the development of a highly sensitive amperometric biosensor for the analysis of phenolic compounds such as catechol. The biosensor architecture is based on the immobilization of tyrosinase (Tyr) on a screen-printed carbon electrode (SPE) modified with nanodiamond particles (ND), 1-butyl-3-methylimidazolium hexafluorophosphate (IL) and poly-l-lysine (PLL). Surface morphologies of the electrodes during the modification process were evaluated by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) were used to investigate the electrochemical characteristics of the modified electrodes. Owing to the synergistic effect of the modification materials, the Tyr/PLL/ND-IL/SPE exhibited high sensitivity (328.2 μA mM-1) towards catechol with a wide linear range (5.0 × 10-8 - 1.2 × 10-5 M) and low detection limit (1.1 × 10-8 M). Furthermore, the method demonstrated good reproducibility and stability. The amperometric response of the biosensor towards other phenolic compounds such as bisphenol A, phenol, p-nitrophenol, m-cresol, p-cresol and o-cresol was also investigated. The analytical applicability of the biosensor was tested by the analysis of catechol in tap water. The results of the tap water analysis showed that the Tyr/PLL/ND-IL/SPE can be used as a practical and effective method for catechol determination.

Quantitative detection of phenol in wastewater using square wave voltammetry with pre-concentration

Phenol is a common pollutant found in wastewater, and its allowable discharge limit is 0.5 parts-per-million (ppm). Therefore, it is critical to monitor phenol in the sub-ppm range with high sensitivity and a low limit of detection. Herein, we report a quantitative method for detecting phenol in industrial wastewater through square wave voltammetry (SWV), in which phenol is oxidized to phenoxyl radicals and then became catechol and hydroquinone for detection. By using this method, phenol in the sub-ppm range can be detected reliably over a wide pH range. The sensitivity can be further improved by using a pre-concentration step for phenol before scanning. The method has a limit of detection of 0.1 ppb for phenol. Finally, three graphite electrodes were applied as working, counter and reference electrodes, respectively, in a millifluidic device for continuous detection of phenol in industrial wastewater flowing at 300 μL/min. Because of its simplicity, the sensor can be mass-produced and deployed on a large scale to monitor phenol in industrial wastewater.

Analytical performance of functional nanostructured biointerfaces for sensing phenolic compounds

Electrochemical biointerfaces are constructed with a wide range of nanomaterials and conducting polymers that strongly affect the analytical performance of biosensors. The analysis of progress toward electrochemical sensing platforms offers opportunities to provide devices for commercial use. The investigation of different methods for the synthesis of phenol biointerfaces leads to design challenges in the field of monitoring phenolic compounds. This paper review the innovative strategies and feature techniques in the construction of phenolic compound biosensors. The focus was made on the preparation methods of nanostructures and nanomaterials design for catalytic improvements of sensing interfaces. The paper also provides a comprehensive overview in the field of enzyme immobilization approaches at solid supports and technical formation of polymer nanocomposites, as well as applications of hybrid organic-inorganic nanocomposites in phenolic biosensors. This review also highlights the recent progress in the electrochemical detection of phenolic compounds and summarizes analytical performance parameters including sensitivity, storage stability, limit of detection, linear range, and Michaelis-Menten kinetic analysis. It also emphasizes advances from the past decade including technical challenges for the construction of suitable biointerfaces for monitoring phenolic compounds.

Promotion effect of Zn on 2D bimetallic NiZn metal organic framework nanosheets for tyrosinase immobilization and ultrasensitive detection of phenol

Environmental monitoring of pollutants is essential to guarantee the human health and maintain the ecosystem. The exploration of both simple and sensitive detection method has aroused widespread attentions. Herein, 2D bimetallic metal organic framework nanosheets (NiZn-MOF NSs) with tunable Ni/Zn ratios were synthesized, and for the first time employed to construct a tyrosinase biosensor. It is revealed that Zn element not only tuned the porosity structure and electronic structure of MOF NSs, but also modified their electrochemical activity. As a result, enzyme immobilization and electrochemical sensing performance of the NiZn-MOF NSs based biosensor were significantly enhanced by a suitable Zn addition. The fabricated tyrosinase biosensor exhibited excellent analytical detections, with a wide linear range from 0.08 μM to 58.2 μM, a high sensitivity of 159.3 mA M^-1, and an ultralow detection limit of 6.5 nM. In addition, the proposed biosensing approach also demonstrated good repeatability, superior selectivity, long-term stability, and high recovery for phenol detection in the real tap water samples.

Highly sensitive paper-based electrochemical sensor for reagent free detection of bisphenol A

Bisphenol A is one the most relevant endocrine disruptors for its toxicity and ubiquity in the environment, being largely employed as raw material for manufacturing processes of a wide number of compounds. Furthermore, bisphenol A is released in the drinking water when plastic-based bottles are incorrectly transported under sunlight, delivering contaminated drinking water. For the health of human beings and the environment, rapid and on site detection of bisphenol A in drinking water is an important issue. Herein, we report a novel and cost-effective printed electrochemical sensor for an enzymatic-free bisphenol A detection. This sensor encompasses the entire electrochemical cell printed on filter paper and the reagents for the measurement loaded in the cellulose fiber network, for delivering a reagent-free analytical tool. The working electrode was printed using ink modified with carbon black, a cost effective nanomaterial for sensitive and sustainable bisphenol A determination. Several parameters including pH, frequency, and amplitude were optimized allowing for a detection limit of 0.03 μM with two linear ranges 0.1-0.9 μM and 1 μM-50 μM, using square wave voltammetry as electrochemical technique. The satisfactory recovery values found in river and drinking water samples demonstrated the suitability of this sensor for screening analyses in water samples. These results revealed the attractiveness of this paper-based device thanks to the synergic combination of paper and carbon black as cost-effective materials.

Development of a new bisphenol A electrochemical sensor based on a cadmium(ii) porphyrin modified carbon paste electrode

In this study, the (5,10,15,20-tetrakis[(4-methoxyphenyl)]porphyrinato)cadmium(ii) complex ([Cd(TMPP)]) was successfully used as a modifier in a carbon paste electrode (CPE) and exploited for bisphenol A (BPA) detection. Analytical performance revealed two linear ranges from 0.0015–15 μM and 0.015–1.5 mM with a detection limit of 13.5 pM. The proposed method was implemented in water samples, which resulted in quantitative signals over the range 6.5–1000 μM with recoveries between 92.6 and 107.7% for tap water and between 96.6 to 106.0% for mineral water.

In this study, the (5,10,15,20-tetrakis[(4-methoxyphenyl)]porphyrinato)cadmium(ii) complex ([Cd(TMPP)]) was successfully used as a modifier in a carbon paste electrode (CPE) and exploited for bisphenol A (BPA) detection.

Fabrication of a novel biosensor for biosensing of bisphenol A and detection of its damage to DNA

In this work, a novel electrochemical biosensor has been fabricated based on step-by-step modification of a glassy carbon electrode (GCE) with methylene blue (MB)-DNA/multiwalled carbon nanotubes (MWCNTs)-chitosan (CS)/palladium nanoparticles (Pd NPs)/fullerene C₆₀ (C₆₀) for voltammetric and impedimetric detection of DNA damage induced by bisphenol A (BPA). Modifications applied to the GCE were characterized by cyclic voltammetry (CV), differential pulse voltammetry (DPV), electrochemical impedance spectroscopy (EIS) and scanning electron microscopy. The EIS and DPV responses of the biosensor were increased and decreased, respectively, by the DNA damage induced by BPA which led us to develop novel systems for detection of DNA damage. Our records confirmed that the biosensor was able to rapid and sensitive detection of DNA damage induced by BPA. Finally, according to the developed systems for detection of DNA damage, we have developed voltammetric and impedimetric methods for determination of BPA.

A novel non-enzymatic zinc oxide thin film based electrochemical recyclable strip with device interface for quantitative detection of catechol in water

Catechol, one of the major effluents released by various chemical and metal processing industries, causes severe pollution of groundwater. Monitoring of catechol in water using cost-effective, handheld sensor is demanding for the safety of the environment. In this work, non-enzymatic zinc oxide thin film based electrochemical strip sensor is developed on conducting glass substrate for detection of catechol. The preparation of strip without employing standard Pt or Ag/AgCl electrodes and simply depositing ZnO through wet chemical process represents a cost-effective innovative technique. The ZnO thin film is characterized using field emission scanning electron microscope (FESEM), energy dispersive X-ray spectroscopy (EDS), atomic force microscopy (AFM) and grazing incidence X-ray diffractometer (GIXRD). Catechol is electrochemically detected by means of cyclic voltammetry and amperometry. A prominent redox peak of the developed strip attributed to the detection of catechol is observed at -0.26 V in cyclic voltammetry. The strip is integrated with readout meter and an algorithm is built based on the experimentally observed linear variation of amperometric current with catechol concentration. The quantitative detection performance is demonstrated by testing 0.1-12 ppm catechol solutions.

Novel grafted electrochemical interface for covalent glucose oxidase immobilization using reactive pentafluorophenyl methacrylate

One of the most important factors for the proper functioning of enzymatic electrochemical biosensors is the enzyme immobilization strategy. In this work, glucose oxidase was covalently immobilized using pentafluorophenyl methacrylate (PFM) by applying two different surface modification techniques (plasma polymerization and plasma-grafting). The grafted surface was specifically designed to covalently anchor enzyme molecules. It was observed using QCM-D measurements the PFM plasma-grafted surfaces were able to retain a higher number of active enzyme molecules than the PFM polymerized surfaces. An amperometric glucose biosensor using titanium dioxide nanotubes array (TiO₂NTAs) modified by PFM plasma-grafted surface was prepared. The resulting biosensor exhibited a fast response and short analysis time (approximately eight minutes per sample). Moreover, this biosensor achieved high sensitivity (9.76 μA mM^-1) with a linear range from 0.25 to 1.49 mM and a limit of detection (LOD) equal to 0.10 mM of glucose. In addition, the glucose content of 16 different food samples was successfully measured using the developed biosensor. The obtained results were compared with the respective HPLC value and a deviation smaller than 10% was obtained in all the cases. Therefore, the biosensor was able to overcome all possible interferences in the selected samples/matrices.

A novel copper(ıı) phthalocyanine-modified multiwalled carbon nanotube-based electrode for sensitive electrochemical detection of bisphenol A

A novel copper(ii) phthalocyanine (CuPc)-modified multiwalled carbon nanotube-based electrode was prepared for the sensitive electrochemical detection of bisphenol A, by the modification of a pencil graphite electrode via the adsorption method.

Advances in sensing and biosensing of bisphenols: A review

Bisphenols (BPs) are well known endocrine disrupting chemicals (EDCs) that cause adverse effects on the environment, biotic life and human health. BPs have been studied extensively because of an increasing concern for the safety of the environment and for human health. They are major raw materials for manufacturing polycarbonates, thermal papers and epoxy resins and are considered hazardous environmental contaminants. A vast array of sensors and biosensors have been developed for the sensitive screening of BPs based on carbon nanomaterials (carbon nanotubes, fullerenes, graphene and graphene oxide), quantum dots, metal and metal oxide nanocomposites, polymer nanocomposites, metal organic frameworks, ionic liquids and molecularly imprinted polymers. This review is devoted mainly to a variety of sensitive, selective and reliable sensing and biosensing methods for the detection of BPs using electrochemistry, fluorescence, colorimetry, surface plasmon resonance, luminescence, ELISAs, circular dichroism, resonance Rayleigh scattering and adsorption techniques in plastic products, food samples, food packaging, industrial wastes, pharmaceutical products, human body fluids and many other matrices. It summarizes the advances in sensing and biosensing methods for the detection of BPs since 2010. Furthermore, the article discusses challenges and future perspectives in the development of novel sensing methods for the detection of BP analogs.

Direct Electrochemical Detection of Bisphenol A Using a Highly Conductive Graphite Nanoparticle Film Electrode

We developed an accurate and sensitive sensor for electrochemical detection of bisphenol A (BPA) with a high-conductivity graphite nanoparticle (GN) film electrode. The GNs consisted of several stacked graphene sheets and showed a homogenous spherical shape, high conductivity, large surface area and good adsorption properties to BPA. The constructed GN film electrode exhibited improved amperometric current responses such as decreased impedance and lowered BPA oxidation potential compared with those of a pristine electrode, and also possessed a large surface area to allow fast electron transfer and BPA accumulation. A pre-accumulation process with BPA adsorption resulted in considerable current signal enhancement during BPA detection. The loading amount of GNs on the film electrode and the time for target BPA enrichment were optimized. The GN film electrode-based sensor showed high reproducibility and high selectivity for BPA over other reagents. Differential pulse voltammetry experiments revealed that the concentrations of BPA were linearly correlated with the current changes, and the lowest limit of detection of the sensor was 35 nM. Furthermore, the sensor showed great accuracy and reliability, as confirmed by high-performance liquid chromatography measurements. The sensor was also successfully used for BPA determination in groundwater samples, demonstrating its potential for real environmental analysis.

Photoelectrochemical sensing of bisphenol a based on graphitic carbon nitride/bismuth oxyiodine composites

Graphitic carbon nitride/bismuth oxyiodine composites with excellent photoelectrochemical performance had been designed for sensitive PEC monitoring platform of bisphenol A.

Graphene-bimetallic nanoparticle composites with enhanced electro-catalytic detection of bisphenol A

This study brings for the first time novel knowledge about the synthesis by catalytic chemical vapor deposition with induction heating of graphene-bimetallic nanoparticle composites (Gr-AuCu and Gr-AgCu) and their morphological and structural characterization by transmission electron microscopy, Raman spectroscopy, and x-ray powder diffraction. Gold electrodes modified with the obtained materials exhibit an enhanced electro-catalytic effect towards one of the most encountered estrogenic disruptive chemicals, bisphenol A (BPA). The BPA behavior in varying pH solutions was investigated using the electrochemical quartz crystal microbalance, which allowed the accurate determination of the number of molecules involved in the oxidation process. The modified electrodes promote the oxidation of BPA at significantly lower potentials (0.66 V) compared to bare gold (0.78 V). In addition, the peak current density recorded with such electrodes greatly exceeded that obtained with bare gold (e.g. one order of magnitude larger, for a Au/Gr-AgCu electrode). The two modified electrodes have low detection limits, of 1.31 × 10^-6 M and 1.91 × 10^-6 M for Au/Gr-AgCu and Au/Gr-AuCu, respectively. The bare gold electrode has a higher detection limit of 5.1 × 10^-6 M. The effect of interfering species (e.g. catechol and 3-nitrophenol) was also investigated. Their presence influenced not only the BPA peak potential, but also the peak current. With both modified electrodes, no peak currents were recorded below 3 × 10^-5 M BPA.

Acetylene black paste electrode modified with molecularly imprinted polymers/graphene for the determination of bisphenol A

A novel nanocomposite of molecularly imprinted polymers and graphene sheets was fabricated and used to obtain a highly conductive acetylene black paste electrode with high conductivity for the detection of bisphenol A. The two-dimensional structure and the chemical functionality of graphene provide an excellent surface for the enhancement of the sensitivity of the electrochemical sensor and the specificity of molecularly imprinted polymers to improve detection of bisphenol A. The synergistic effect between graphene and molecularly imprinted polymers confers the nanocomposite with superior conductivity, broadened effective surface area and outstanding electrochemical performance. Factors affecting the performance of the imprinted sensor such as molecularly imprinted polymers concentration, foster time and scan rate are discussed. The sensor successfully detects bisphenol A with a wide linear range of 3.21 × 10^-10 to 2.8 × 10^-1 g/L (R = 0.995) and a detection limit of 9.63 × 10^-11 g/L. The fabricated sensor also possessed high selectivity and stability and exhibits potential for environmental detection of contaminants and food safety inspection.

Tyrosinase conjugated reduced graphene oxide based biointerface for bisphenol A sensor

We have fabricated a nanocomposite of reduced graphene oxide (rGO) sheets and chitosan (Cn) polymer based highly sensitive electrochemical biosensor for detection of bisphenol A (BPA). The two-dimensional structure and chemical functionality of rGO and Cn provide an excellent electrode surface for loading of tyrosinase enzyme molecules. This rGO-Cn nanocomposite is capable of effectively utilizing their superior conductivity, larger effective surface area and superior electrochemical performance due to its synergistic effect between rGO and Cn. The structural, morphological and electrochemical characterizations of nanocomposite sheets have been performed by electron microscopy, X-ray diffraction, FTIR and Potentiostat/Galvanostat techniques. This fabricated biosensor is sensitive to nanomolar (0.74 nM) concentration of BPA and detection time is 10s compared to conventional BPA ELISA kit (0.3 µg/L and 2.5h). The rGO-Cn based biosensor exhibits a higher sensitivity (83.3 µA nM(-1) cm(-2)), wider linearity (0.01-50 µM) with good selectivity towards BPA. This biosensor is capable to quantify real sample of BPA using packaged drinking water bottles. This rGO-Cn nanocomposite sheets emerges as a potential electrode material for detection of other estrogenic substrate.

Monitoring bisphenol A and its biodegradation in water using a fluorescent molecularly imprinted chemosensor

In this paper, we present a simple and rapid method for monitoring bisphenol A (BPA) and its biodegradation in environmental water using a fluorescent molecularly imprinted polymer chemosensor (fMIPcs). A fluorescent molecularly imprinted polymer (fMIP) was first synthesized by precipitation polymerization method using BPA as template, dansyl methacrylate as functional monomer. Then a fMIPcs was constructed by combining the fMIP with a fluorescent microplate reader. The fMIPcs displayed selective, concentration-dependent fluorescence quenching in response to BPA in water even in the existence of interferences, thereby allowing reliable high through-put quantification of BPA via simple fluorescence measurements. The fMIPcs was able to directly quantify BPA (from 10 to 2000 μg L(-1)) in different environmental water samples (distilled water, distilled water containing heavy metals and humic acid, tap water, and river water) with high accuracy, and to monitor BPA biodegradation in real-time. Using the fMIPcs, it was possible to achieve fast analytical results with lower limit of detection for BPA (3 μg L(-1)) from smaller sample volume (250 μL), which are superior to many relevant methods reported in the literature. Moreover, BPA levels and biodegradation rates measured by fMIPcs are comparable to the instrument-based method (HPLC). The fMIPcs developed in this work offers a new solution for simple, rapid, accurate and high through-put BPA quantification, and makes it possible to monitor BPA biodegradation in real time.

A highly sensitive electrochemical sensor for simultaneous determination of hydroquinone and bisphenol A based on the ultrafine Pd nanoparticle@TiO2 functionalized SiC

A titanium dioxide-silicon carbide nanohybrid (TiO2-SiC) with enhanced electrochemical performance was successfully prepared through a facile generic in situ growth strategy. Monodispersed ultrafine palladium nanoparticles (Pd NPs) with a uniform size of ∼2.3 nm were successfully obtained on the TiO2-SiC surface via a chemical reduction method. The Pd-loaded TiO2-SiC nanohybrid (Pd@TiO2-SiC) was characterized by transmission electron microscopy and X-ray diffractometry. A method for the simultaneous electrochemical determination of hydroquinone (HQ) and bisphenol A (BPA) using a Pd@TiO2-SiC nanocomposite-modified glassy carbon electrode was established. Utilizing the favorable properties of Pd NPs, the Pd@TiO2-SiC nanohybrid-modified glassy carbon electrode exhibited electrochemical performance superior to those of TiO2-SiC and SiC. Differential pulse voltammetry was successfully used to simultaneously quantify HQ and BPA within the concentration range of 0.01-200 μM under optimal conditions. The detection limits (S/N=3) of the Pd@TiO2-SiC nanohybrid electrode for HQ and BPA were 5.5 and 4.3 nM, respectively. The selectivity of the electrochemical sensor was improved by introducing 10% ethanol to the buffer medium. The practical application of the modified electrode was demonstrated by the simultaneous detection of HQ and BPA in tap water and wastewater samples. The simple and straightforward strategy presented in this paper are important for the facile fabrication of ultrafine metal NPs@metal oxide-SiC hybrids with high electrochemical performance and catalytic activity.