Carbon nanotube/polymer composite electrodes for flexible, attachable electrochemical DNA sensors

Electrochemically Effective Surface Area of a Polyaniline Nanowire-Based Platinum Microelectrode and Development of an Electrochemical DNA Sensor

Electrochemical DNA sensors based on nanocomposite materials of polyaniline nanowires (PANi NWs) have been published in the literature. However, it is interesting that there are very few research studies related to the development of electrochemical DNA sensors based on PANi NWs individually. In this study, PANi NWs were synthesized site-specifically on a Pt microelectrode with only 0.785 mm2 area using an electropolymerization procedure. The electrosynthesis allows direct deposition of PANi NWs onto the Pt microelectrode in a rapid and cost-effective way. The good properties of PANi NWs including uniform size, uniform distribution throughout the Pt working electrode, and H2SO4 doping which improved the conductivity of the PANi material were obtained. Especially, the electrochemically effective surface area of the PANi NW-based Pt microelectrode determined in this work is nearly 19 times larger than that of the Pt working electrode. The PANi NW layer with large electrochemically effective surface area and high biocompatibility is consistent with the application in electrochemical DNA sensors. The fabricated DNA sensors show advantages such as simple fabrication, direct detection, high sensitivity (with the detection limit of 2.48 × 10−14 M), good specificity, and low sample volume requirement. This study also contributes to confirm the role of PANi NWs in DNA probe immobilization as well as in electrochemical signal transmission in the development of electrochemical DNA sensors.

Physical Surface Modification of Carbon-Nanotube/Polydimethylsiloxane Composite Electrodes for High-Sensitivity DNA Detection

The chemical modification of electrode surfaces has attracted significant attention for lowering the limit of detection or for improving the recognition of biomolecules; however, the chemical processes are complex, dangerous, and difficult to control. Therefore, instead of the chemical process, we physically modified the surface of carbon-nanotube/polydimethylsiloxane composite electrodes by dip coating them with functionalized multi-walled carbon nanotubes (F-MWCNTs). These electrodes are used as working electrodes in electrochemistry, where they act as a recognition layer for sequence-specific DNA sensing through π-π interactions. The F-MWCNT-modified electrodes showed a limit of detection of 19.9 fM, which was 1250 times lower than that of pristine carbon/polydimethylsiloxane electrodes in a previous study, with a broad linear range of 1-1000 pM. The physically modified electrode was very stable during the electrode regeneration process after DNA detection. Our method paves the way for utilizing physical modification to significantly lower the limit of detection of a biosensor system as an alternative to chemical processes.

Flexible paper-based Ni-MOF composite/AuNPs/CNTs film electrode for HIV DNA detection

It is very important to develop a rapid, simple, low cost point-of-care (POC) method for the early diagnosis of pathogens. In this work, a flexible paper-based electrode based on nickel metal-organic framework (Ni-MOF) composite/Au nanoparticles/carbon nanotubes/polyvinyl alcohol (Ni-Au composite/CNT/PVA) was constructed to detect target human immunodeficiency virus (HIV) DNA by DNA hybridization using methylene blue (MB) as a redox indicator. The CNT/PVA and Ni-Au composite were deposited on the cellulose membrane by vacuum filtration and drop-coating method in turn to obtain Ni-Au composite/CNT/PVA (CCP) film electrode. Compared to the CNT/PVA film electrode, CCP film electrode makes a higher loading of the probe DNA for its large specific surface area and conjugated π-electron system that can provide hydrogen bond sources to achieve interactions between MOF and single-stranded DNA, which improves the sensitivity for detecting target DNA. The variation of peak current for MB molecules adsorbed onto DNA before and after hybridization with HIV DNA was monitored. Electrochemical results proved that the CCP film maintained stable electrochemical property even after bending 200 times or stretching under different strains from 0% to 20%. The flexible paper electrode showed excellent sensing performance with a linear range of 10 nM-1 μM and a low detection limit of 0.13 nM. The target HIV DNA was successfully detected even in complex serum samples using the flexible CCP film electrode. Therefore, the simple and inexpensive flexible paper-based MOF composite film electrode can also be utilized for other pathogens POC diagnosis.

Rational Design of Amphiphilic Diblock Copolymer/MWCNT Surface Modifiers and Their Application for Direct Electrochemical Sensing of DNA

We demonstrate the application of amphiphilic ionic poly(n-butylmethacrylate)-block- poly(2-(dimethylamino)ethyl methacrylate) diblock copolymers (PnBMA₄₀-b-PDMAEMA₄₀, PnBMA₄₀-b-PDMAEMA₁₂₀, PnBMA₇₀-b-PDMAEMA₁₂₀) for dispersing multiwalled carbon nanotubes (MWCNTs) in aqueous media, a subsequent efficient surface modification of screen-printed electrodes (SPEs), and the application of the modified SPEs for DNA electrochemistry. Stable and fine aqueous dispersions of MWCNTs were obtained with PnBMA_x-b-PDMAEMA_y diblock copolymers, regardless of the structure of the copolymer and the amount of MWCNTs in the dispersions. The effect of the diblock copolymer structure was important when the dispersions of MWCNTs were deposited as modifying layers on surfaces of SPEs, resulting in considerable increases of the electroactive surface areas and great acceleration of the electron transfer rate. The SPE/(PnBMA_x-b-PDMAEMA_y + MWCNT) constructs were further exploited for direct electrochemical oxidation of the guanine (G) and adenine (A) residues in a model salmon sperm double-stranded DNA (dsDNA). Two well-defined irreversible oxidation peaks were observed at about +600 and +900 mV, corresponding to the electrochemical oxidation of G and A residues, respectively. A multi-parametric optimization of dsDNA electrochemistry enables one to get the limits of detection (LOD) as low as 5 μg/mL (0.25 μM) and 1 μg/mL (0.05 μM) for G and A residues, respectively. The achieved sensitivity of DNA assay enables quantification of the A and G residues of dsDNA in the presence of human serum and DNA in isolated human leukocytes.

A miniaturized electrochemical platform with an integrated PDMS reservoir for label-free DNA hybridization detection using nanostructured Au electrodes

We report the fabrication and characterization of a miniaturized electrochemical platform for the label-free detection of DNA hybridization. The proposed platform is fabricated using microfabrication and electrodeposition techniques. Comprising a Ti working electrode with electrodeposited Au nanostructures, and Pt/Au pseudo-reference and counter electrodes, the device accounts for a limit of detection of 0.97 fM and a sensitivity of 20.78 (μA μM-1) cm-2 with respect to Dengue virus specific consensus primer detection in the range of 10 fM-1 μM. Here, the incorporation of nanostructured Au in the active sensing area not only enhances the current response by increasing the overall surface area, but it also facilitates facile probe DNA immobilization by gold-thiol self-assembly. We have used differential pulse voltammetry analysis in this study to monitor the changes in reaction kinetics with respect to target hybridization. Furthermore, the evaluation of reproducibility of the biosensor and its selectivity against interference has yielded acceptable outcomes. Additionally, in order to evaluate the system's selectivity, we have successfully distinguished PCR amplified wild type and mutant target DNAs corresponding to the BRCA1 specific gene. Here, the mutant and the wild type target DNAs differ by a two base deletion, and the fact that the system is able to differentiate even such minute dissimilarities under hybridization conditions is indicative of its superior performance.

Soft and flexible material-based affinity sensors

Recent advances in biosensors and point-of-care (PoC) devices are poised to change and expand the delivery of diagnostics from conventional lateral-flow assays and test strips that dominate the market currently, to newly emerging wearable and implantable devices that can provide continuous monitoring. Soft and flexible materials are playing a key role in propelling these trends towards real-time and remote health monitoring. Affinity biosensors have the capability to provide for diagnosis and monitoring of cancerous, cardiovascular, infectious and genetic diseases by the detection of biomarkers using affinity interactions. This review tracks the evolution of affinity sensors from conventional lateral-flow test strips to wearable/implantable devices enabled by soft and flexible materials. Initially, we highlight conventional affinity sensors exploiting membrane and paper materials which have been so successfully applied in point-of-care tests, such as lateral-flow immunoassay strips and emerging microfluidic paper-based devices. We then turn our attention to the multifarious polymer designs that provide both the base materials for sensor designs, such as PDMS, and more advanced functionalised materials that are capable of both recognition and transduction, such as conducting and molecularly imprinted polymers. The subsequent content discusses wearable soft and flexible material-based affinity sensors, classified as flexible and skin-mountable, textile materials-based and contact lens-based affinity sensors. In the final sections, we explore the possibilities for implantable/injectable soft and flexible material-based affinity sensors, including hydrogels, microencapsulated sensors and optical fibers. This area is truly a work in progress and we trust that this review will help pull together the many technological streams that are contributing to the field.

Aligned Carbon Nanotubes Reduce Hypertrophic Scar via Regulating Cell Behavior

Hypertrophic scars, characterized by excessive cell proliferation, disordered cell growth, and aberrant deposition of collagens, could cause significant clinical problems. Herein, aligned carbon nanotubes (ACNTs) were synthesized via chemical vapor deposition, and bulk ACNTs were pulled out from the arrays. The capacity of the ACNTs to reduce hypertrophic scar formation was evaluated both in vitro and in vivo. The results demonstrated that the ACNTs suppressed the overproliferation of fibroblast cells, directed their growth, and inhibited collagen expression in vitro without cell cytotoxicity. Moreover, in vivo evaluation in a rabbit ear model indicated relieved scar hypertrophy after the ACNTs treatment. The gene expression microarray was further used to understand the mechanism, which showed that ACNTs could inhibit the TGFβ pathway to alter the components in the extracellular matrix, cell proliferation, cell cytoskeleton, and cell motility. These findings may provide a potent strategy of using carbon nanotubes in the bioengineering field.

Evaluation of carbon nanotube based copper nanoparticle composite for the efficient detection of agroviruses

We report a biosensor that combines the construction of a three-dimensional nanocomposite with electrochemical methods for the detection of viruses in plants. This is the first report, where carbon nanotubes are used as a conductive frame to anchor highly electrolytic agglomerates of copper nanoparticles to detect agroviruses. Morphological analysis of nanocomposite revealed the presence of carbon nanotubes having a diameter of 50-100nm with copper nanoparticles of 20-100nm, attached in the form of bunches. This material was applied to assess the infection caused by geminiviruses which are a major threat to the cotton plants in Asian and African countries. The hybridization events were studied by monitoring differential pulse voltammetry signals using methylene blue as a redox indicator. In the presence of target DNA, sensor signals decreased from 7×10^-4 to 1×10^-4Ampere. The probe exhibited 97.14% selectivity and the detection limit was found to be 0.01ngμL^-1. The developed biosensor is stable for at least four weeks, losing only 4.3% of the initial signal value. This sensor was able to detect the presence of viruses in sap extracted from cotton leaves, thus providing a promising platform to detect a range of other crops-infecting viruses.

Development of a porous 3D graphene-PDMS scaffold for improved osseointegration

Osseointegration in orthopedic surgery plays an important role for bone implantation success. Traditional treatment of implant surface aimed at improved osseointegration has limited capability for its poor performance in supporting cell growth and proliferation. Polydimethylsiloxane (PDMS) is a widely used silicon-based organic polymer material with properties that are useful in cosmetics, domestic applications and mechanical engineering. In addition, the biocompatibility of PDMS, in part due to the high solubility of oxygen, makes it an ideal material for cell-based implants. Notwithstanding its potential, a property that can inhibit PDMS bioactivity is the high hydrophobicity, limiting its use to date in tissue engineering. Here, we describe an efficient approach to produce porous, durable and cytocompatible PDMS-based 3D structures, coated with reduced graphene oxide (RGO). The RGO/PDMS scaffold has good mechanical strength and with pore sizes ranging from 10 to 600μm. Importantly, the scaffold is able to support growth and differentiation of human adipose stem cells (ADSCs) to an osteogenic cell lineage, indicative of its potential as a transition structure of an osseointegrated implant.

A liquid-crystal-based DNA biosensor for pathogen detection

A liquid-crystal (LC)-filled transmission electron microscopy (TEM) grid cell coated with the cationic surfactant dodecyltrimethylammonium bromide (DTAB), to which a single-stranded deoxyribonucleic acid probe (ssDNAprobe) was adsorbed at the LC/aqueous interface (TEMDTAB/DNA), was applied for the highly specific detection of target DNA molecules. The DTAB-coated E7 (used LC mixture) in the TEM grid (TEMDTAB) exhibited a homeotropic orientation, and changed to a planar orientation upon adsorption of the ssDNAprobe. The TEMDTAB/DNA was then exposed to complementary (target) ssDNA, which resulted in a planar-to-homeotropic configurational change of E7 that could be observed through a polarized optical microscope under crossed polarizers. The optimum adsorption density (2 μM) of ssDNAprobe enabled the detection of ≥0.05 nM complementary ssDNA. This TEMDTAB/DNA biosensor could differentiate complementary ssDNA from mismatched ssDNA as well as double-stranded DNA. It also successfully detected the genomic DNAs of the bacterium Erwinia carotovora and the fungi Rhazictonia solani. Owe to the high specificity, sensitivity, and label-free detection, this biosensor may broaden the applications of LC-based biosensors to pathogen detection.

Engineered Carbon-Nanomaterial-Based Electrochemical Sensors for Biomolecules

The study of electrochemical behavior of bioactive molecules has become one of the most rapidly developing scientific fields. Biotechnology and biomedical engineering fields have a vested interest in constructing more precise and accurate voltammetric/amperometric biosensors. One rapidly growing area of biosensor design involves incorporation of carbon-based nanomaterials in working electrodes, such as one-dimensional carbon nanotubes, two-dimensional graphene, and graphene oxide. In this review article, we give a brief overview describing the voltammetric techniques and how these techniques are applied in biosensing, as well as the details surrounding important biosensing concepts of sensitivity and limits of detection. Building on these important concepts, we show how the sensitivity and limit of detection can be tuned by including carbon-based nanomaterials in the fabrication of biosensors. The sensing of biomolecules including glucose, dopamine, proteins, enzymes, uric acid, DNA, RNA, and H2O2 traditionally employs enzymes in detection; however, these enzymes denature easily, and as such, enzymeless methods are highly desired. Here we draw an important distinction between enzymeless and enzyme-containing carbon-nanomaterial-based biosensors. The review ends with an outlook of future concepts that can be employed in biosensor fabrication, as well as limitations of already proposed materials and how such sensing can be enhanced. As such, this review can act as a roadmap to guide researchers toward concepts that can be employed in the design of next generation biosensors, while also highlighting the current advancements in the field.

Electrochemically reduced graphene oxide supported poly(indole-5-carboxylic acid) nanocomposite for genosensing application

An ultrasensitive DNA electrochemical biosensing interface was developed for rapid determination of BCR/ABL fusion gene by employing ERGNO supported PICA.