Highly sensitive and chemically stable NH3 sensors based on an organic acid-sensitized cross-linked hydrogel for exhaled breath analysis

Bi2Sn2O7 Overlayer Assists Bilayer Chemiresistor in Humidity-Independent and Highly Selective Detection of Expiratory Acetone

Constructing a bilayer structure has not been reported as a method to mitigate the adverse effect of water poisoning on oxide chemiresistors while simultaneously enhancing gas selectivity and sensitivity. To address this challenge, pyrochlore-Bi2Sn2O7 has been first utilized as an overlayer on a ZnO sensing layer for constructing a bilayer acetone chemiresistor, leading to remarkable improvement in the performance for trace-level (500 p-p-b) acetone detection under high humidity (80% relative humidity). In addition, owing to the catalytic predecompositions of ethanol across the overlayer, an outstanding acetone gas selectivity (Sacetone/Sethanol = 2.9) has been achieved, with a more than 4-fold improvement compared with monolayer ZnO chemiresistor (Sacetone/Sethanol = 0.7). More significantly, comprehensive experiments coupled with in situ characterizations have verified the generation of hydroxyl radicals (•OH) on the Bi2Sn2O7 overlayer. These radicals are capable of enhancing the kinetics between •OH and acetone, reducing the activation energy required for the gas sensing reaction, and thus leading to an unexpected phenomenon of enhanced acetone sensitivity under high humid conditions (Sacetone at 80% RH > Sacetone at 5% RH). These demonstrations offer crucial insight into the precise design of highly efficient overlayers for breath sensing.

MoS2-Based NH3 Sensor for In Situ Helicobacter pylori Detection

Detection of Helicobacter pylori is essential for the prevention of gastric cancer. By detecting the metabolized NH3, it was able to noninvasively reveal the state of H. pylori; however, it is still a challenge since the metabolized NH3 concentration is much lower for conventional gas sensors. Herein, we developed a MoS2-based NH3 sensor for continuous, real-time monitoring of H. pylori growth. The atomic thin layer and the all-exposed surface of MoS2 facilitate NH3 adsorption and charge transferring. A high-response NH3 sensor was prepared by surface decoration of MoS2 by depositing metal nanoparticles. The Fe-decorated MoS2 sensor outperformed with a high response of 40.9% for 5.7 ppm of NH3 at 25 ± 2 °C, low LOD (6.2 ppb), and long-term stability with a response of 12.5% for 5.7 ppm of NH3 after 5 months. The Fe-decorated MoS2 sensor was applied to the detection of H. pylori and the real-time in situ monitoring of its 92 h growth cycle. The NH3 release curve of the exponential phase during H. pylori growth was continuously monitored, and the NH3 concentration was quantified. The maximum specific rate of NH3 release was 0.195 ± 0.005 h-1, which is well-consistent with the nature of H. pylori growth. This study opens up a technological roadmap for noninvasive detection of H. pylori in the future.

Portable and Hand-Held Ammonia Gas Sensor Enables Noninvasive Prediagnosis of Helicobacter pylori Infection

Disease diagnosis of Helicobacter pylori (Hp) through human exhaled breath analysis has attracted considerable attention. However, conventional methods, such as carbon 13 (13C) breath test and infrared spectrometers, are facing the challenge of achieving portability and reliability synchronously. Herein, we report a portable and hand-held Hp analyzer using a bimetallic PtRu@SnO2-based gas sensor for the prediagnosis of Hp infection, which is based on detecting ammonia (NH3) as a potential biomarker in exhaled breath. Owing to the surface functionalization through highly catalytically active bimetallic PtRu nanoparticles (NPs) prepared by a photochemical reduction strategy, the PtRu@SnO2-based sensor exhibits high sensitivity and selectivity toward trace-level (200 ppb) NH3 even at high-humidity surroundings (80% RH). Consequently, the designed portable and hand-held Hp analyzer makes the accurate determination of NH3 at 800 ppb in exhaled breath. The tuning of energy band structure and electrical characteristics and the catalytic modulation of NH3 oxidation by PtRu NPs are proposed to be the reasons behind the enhanced NH3 gas-sensing performance, as confirmed by in situ analysis using an online MKS MultiGas 2030 FTIR gas analyzer. This work paves the way for the prediagnosis of Hp infection using a metal oxide gas sensor.

From lab to wearables: Innovations in multifunctional hydrogel chemistry for next-generation bioelectronic devices

Functional hydrogels have emerged as foundational materials in diagnostics, therapy, and wearable devices, owing to their high stretchability, flexibility, sensing, and outstanding biocompatibility. Their significance stems from their resemblance to biological tissue and their exceptional versatility in electrical, mechanical, and biofunctional engineering, positioning themselves as a bridge between living organisms and electronic systems, paving the way for the development of highly compatible, efficient, and stable interfaces. These multifaceted capability revolutionizes the essence of hydrogel-based wearable devices, distinguishing them from conventional biomedical devices in real-world practical applications. In this comprehensive review, we first discuss the fundamental chemistry of hydrogels, elucidating their distinct properties and functionalities. Subsequently, we examine the applications of these bioelectronics within the human body, unveiling their transformative potential in diagnostics, therapy, and human-machine interfaces (HMI) in real wearable bioelectronics. This exploration serves as a scientific compass for researchers navigating the interdisciplinary landscape of chemistry, materials science, and bioelectronics.

Smart materials for flexible electronics and devices: hydrogel

In recent years, flexible conductive materials have attracted considerable attention for their potential use in flexible energy storage devices, touch panels, sensors, memristors, and other applications. The outstanding flexibility, electricity, and tunable mechanical properties of hydrogels make them ideal conductive materials for flexible electronic devices. Various synthetic strategies have been developed to produce conductive and environmentally friendly hydrogels for high-performance flexible electronics. In this review, we discuss the state-of-the-art applications of hydrogels in flexible electronics, such as energy storage, touch panels, memristor devices, and sensors like temperature, gas, humidity, chemical, strain, and textile sensors, and the latest synthesis methods of hydrogels. Describe the process of fabricating sensors as well. Finally, we discussed the challenges and future research avenues for flexible and portable electronic devices based on hydrogels.

Self-Healing, Laminated, and Low Resistance NH3 Sensor Based on 6,6',6″-(Nitrilotris(benzene-4,1-diyl))tris(5-phenylpyrazine-2,3-dicarbonitrile) Sensing Material Operating at Room Temperature

With the rapid development of the concept of the Internet of Things (IoT), gas sensors with the function of simulating the human sense of smell became irreplaceable as a key element. Among them, ammonia (NH3) sensors played an important role in respiration tests, environmental monitoring, safety, and other fields. However, the fabrication of the high-performance device with high stability and resistance to mechanical damages was still a challenge. In this work, polyurethane (PU) with excellent self-healing ability was applied as the substrate, and the sensor was designed from new sensitive material design and device structure optimization, through applying the organic molecule with groups which could absorb NH3 and the laminated structure to shorten the electronic transmission path to achieve a low resistance state and favorable sensing properties. Accordingly, a room temperature flexible NH3 sensor based on 6,6',6″-(nitrilotris(benzene-4,1-diyl))tris(5-phenylpyrazine-2,3-dicarbonitrile) (TPA-3DCNPZ) was successfully developed. The device could self-heal by means of a thermal evaporation assisted method. It exhibited a detection limit of 1 ppm at 98% relative humidity (RH), as well as great stability, selectivity, bending flexibility, and self-healing properties. The improved NH3 sensing performance under high RH was further investigated by complex impedance plots (CIPs) and density functional theory (DFT), attributing to the enhanced adsorption of NH3. The TPA-3DCNPZ based NH3 sensors proved to have great potential for application on simulated exhaled breath to determine the severity of kidney diseases and the progress of treatment. This work also provided new ideas for the construction of high-performance room temperature NH3 sensors.

Humidity activated ultra-selective room temperature gas sensor based on W doped MoS2/RGO composites for trace level ammonia detection

The lack of highly efficient, cost effective and stable ammonia gas sensors functionable at room temperature even in extreme humid environments poses significant challenge for the future generation gas sensors. The prime factors that impede the development of such next generation gas sensors are the strong interference of humidity and sluggish selectivity. Herein, we fabricated tungsten doped molybdenum disulphide/reduced graphene oxide composite by an in-situ hydrothermal method to exploit the adsorption, dissolution (solubility), ionization and transmission process of ammonia and thereby to effectuate its trace level detection even in indispensable humid environments. The protype based on 5 at.% Tungsten doped MoS2/RGO (W5) gas sensor exhibited 3.8-fold increment in its response to 50 ppm of ammonia when the relative humidity varied from 20 % to 70 % with ultra-high selectivity at room temperature. The as prepared gas sensor revealed a practical detection limit down to 1 ppm with a substantial response and rapid recovery time. Furthermore, W5 gas sensor exhibited a 42-fold increment in response to 50 ppm of ammonia relative to its pristine (MoS2/RGO) MG composite with a RH of 70 %. The proton hopping mechanism accountable for such an enormous enhancement in ammonia sensing and its potential for breath sensor are briefly annotated.

Highly Conductive, Anti-Freezing Hemicellulose-Based Hydrogels Prepared via Deep Eutectic Solvents and Their Applications

Hydrogels containing renewable resources, such as hemicellulose, have received a lot of attention owing to their softness and electrical conductivity which could be applied in soft devices and wearable equipment. However, traditional hemicellulose-based hydrogels generally exhibit poor electrical conductivity and suffer from freezing at lower temperatures owing to the presence of a lot of water. In this study, we dissolved hemicellulose by employing deep eutectic solvents (DESs), which were prepared by mixing choline chloride and imidazole. In addition, hemicellulose-based DES hydrogels were fabricated via photo-initiated reactions of acrylamide and hemicellulose with N, N'-Methylenebisacrylamide as a crosslinking agent. The produced hydrogels demonstrated high electrical conductivity and anti-freezing properties. The conductivity of the hydrogels was 2.13 S/m at room temperature and 1.97 S/m at -29 °C. The hydrogel's freezing point was measured by differential scanning calorimetry (DSC) to be -47.78 °C. Furthermore, the hemicellulose-based DES hydrogels can function as a dependable and sensitive strain sensor for monitoring a variety of human activities.

Functionalized Hydrogel-Based Wearable Gas and Humidity Sensors

Breathing is an inherent human activity; however, the composition of the air we inhale and gas exhale remains unknown to us. To address this, wearable vapor sensors can help people monitor air composition in real time to avoid underlying risks, and for the early detection and treatment of diseases for home healthcare. Hydrogels with three-dimensional polymer networks and large amounts of water molecules are naturally flexible and stretchable. Functionalized hydrogels are intrinsically conductive, self-healing, self-adhesive, biocompatible, and room-temperature sensitive. Compared with traditional rigid vapor sensors, hydrogel-based gas and humidity sensors can directly fit human skin or clothing, and are more suitable for real-time monitoring of personal health and safety. In this review, current studies on hydrogel-based vapor sensors are investigated. The required properties and optimization methods of wearable hydrogel-based sensors are introduced. Subsequently, existing reports on the response mechanisms of hydrogel-based gas and humidity sensors are summarized. Related works on hydrogel-based vapor sensors for their application in personal health and safety monitoring are presented. Moreover, the potential of hydrogels in the field of vapor sensing is elucidated. Finally, the current research status, challenges, and future trends of hydrogel gas/humidity sensing are discussed.

Online mass spectrometry of exhaled breath with a modified ambient ion source

Exhaled breath (EB) may contain metabolites that are closely related to human health conditions. Real time analysis of EB is important to study its true composition, however, it has been difficult. A robust ambient ionization mass spectrometry method using a modified direct analysis in real time (DART) ion source was developed for the online analysis of breath volatiles. The modified DART ion source can provide a confined region for direct sampling, rapid transmission and efficient ionization of exhaled breath. With different sampling methods, offline analysis and near real-time evaluation of exhaled breath were also achieved, and their unique molecular features were characterized. High resolution MS data aided the putative metabolite identification in breath samples, resulting in hundreds of volatile organic compounds being identified in the exhalome. The method was sensitive enough to be used for monitoring the breath feature changes after taking different food and over-the-counter medicine. Quantification was performed for pyridine and valeric acid with fasting and after ingesting different food. The developed method is fast, simple, versatile, and potentially useful for evaluating the true state of human exhaled breath.

Wearable Dual-Signal NH3 Sensor with High Sensitivity for Non-invasive Diagnosis of Chronic Kidney Disease

NH₃ gas in human exhaled breath contains abundant physiological information related to human health, especially chronic kidney disease (CKD). Unfortunately, up to now, most wearable NH₃ sensors show inevitable defects (low sensitivity, easy to be interfered by the environment, etc.), which may lead to misdiagnosis of CKD. To solve the above dilemma, a nanoporous, heterogeneous, and dual-signal (optical and electrical) wearable NH₃ sensor mask is developed successfully. More specifically, a polyacrylonitrile/bromocresol green (PAN/BCG) nanofiber film as a visual NH₃ sensor and a polyacrylonitrile/polyaniline/reduced graphene oxide (PAN/PANI/rGO) nanofiber film as a resistive NH₃ sensor are constructed. Due to the high specific surface area and abundant NH₃ binding sites of these two nanofiber films, they exhibit good NH₃ sensing performance. However, although the visual NH₃ sensor (PAN/BCG nanofiber film) is simple without the need of any detecting facilities and quite stable when temperature and humidity change, it shows poor sensitivity and resolution. In comparison, the resistive NH₃ sensor (PAN/PANI/rGO nanofiber film) is of high sensitivity, fast response, and good resolution, but its electrical signal is easily interfered by the external environment (such as humidity, temperature, etc.). Considering that the sensing principles between a visual NH₃ sensor and resistive NH₃ sensor are significantly different, a wearable dual-signal NH₃ sensor containing both a visual NH₃ sensor and resistive NH₃ sensor is further explored. Our data prove that the two sensing signals in this dual-signal NH₃ sensor mask can not only work well without interference with each other but also complement each other to improve the sensing accuracy, indicating its potential application in non-invasive diagnosis of CKD.

Constructing Netlike Nanosheets of ZnO/BiOCl with Heterojunction as Robust Material for Electrochemical Amine Detection

The electrochemical sensing is a potential method for detection of trace toxic substance. Herein, the heterojunction of netlike ZnO/BiOCl nanosheets was constructed for the enhanced electrochemical detection of ammonia. Cyclic voltammetry and linear sweep voltammetry were used to investigate the electrochemical performance. The results show that the ZnO/BiOCl-modified electrode exhibits higher sensitivity towards ammonia compared with the ZnO and BiOCl-based electrodes, which is ascribed to band structure and fast electron transfer. The high response of 11.8 μA mM^-1 and a low detection limit (LOD) of 0.25 μM are achieved. In addition, the ZnO/BiOCl material exhibits high selectivity, repeatability and stability. The better linear relationship between concentration and current (R² =0.99) is significant for quantitative detection of ammonia, implying that netlike ZnO/BiOCl nanosheets can serve as electrochemical sensing platform for detecting toxic substance. This research provides a strategy for fabricating two-dimensional netlike materials and regulating heterojunctions used for electrochemical application.

Humidity-Tolerant Room-Temperature Selective Dual Sensing and Discrimination of NH3 and NO Using a WS2/MWCNT Composite

Continuous detection of toxic and hazardous gases like nitric oxide (NO) and ammonia (NH₃) is needed for environmental management and noninvasive diagnosis of various diseases. However, to the best of our knowledge, dual detection of these two gases has not been previously reported. To address the challenge, we demonstrate the design and fabrication of low-cost NH₃ and NO dual gas sensors using tungsten disulfide/multiwall carbon nanotube (WS₂/MWCNT) nanocomposites as sensing channels which maintained their performance in a humid environment. The composite-based device has shown successful dual detection at temperatures down to 18 °C and relative humidity of 90%. For 0.1 ppm ammonia, it exhibited a p-type conduction with response and recovery times of 102 and 261 s, respectively; on the other hand, with NO (10 ppb, n-type), these times were 285 and 198 s, respectively. The device with 5 mg MWCNTs possesses a superior selectivity along with a relative response of ≈7% (5 ppb) and ≈5% (0.1 ppm) for NO and NH₃, respectively, at 18 °C. The response is less affected by relative humidity, and this is attributed to the presence of MWCNTs that are hydrophobic in nature. Upon simultaneous exposure to NO (5-10 ppb) and NH₃ (0.1-5 ppm), the response was dominated by NO, implying clear discrimination to the simultaneous presence of these two gases. We propose a sensing mechanism based on adsorption/desportion and accompanied charge transfer between the adsorbed gas molecules and sensing surface. The results suggest that an optimized weight ratio of WS₂ and MWCNTs could govern favorable sensing conditions for a particular gas molecule.

Hydrogel- and organohydrogel-based stretchable, ultrasensitive, transparent, room-temperature and real-time NO2 sensors and the mechanism

Highly stretchable, sensitive and room-temperature nitrogen dioxide (NO₂) sensors are fabricated by exploiting intrinsically stretchable, transparent and ion-conducting hydrogels and active metals as the novel transducing materials and electrodes, respectively. The NO₂ sensor exhibits high sensitivity (60.02% ppm^-1), ultralow theoretical limit of detection (6.8 ppb), excellent selectivity, linearity and reversibility at room temperature. Notably, the sensitivity can be maintained even under 50% tensile strain. For the first time, it's found that the metal electrodes significantly impact the sensing performance. Specifically, the sensitivity is boosted from 31.18 to 60.02% ppm^-1 by replacing the anodic silver with copper-tin alloy. Importantly, by applying specially designed sensing tests, and microscopic and composition analyses, we have obtained the inherent NO₂ sensing mechanism: the anodic metal tends to be oxidized and the NO₂ molecules tend to react in the cathode-gel interface. The introduction of glycerol converts the hydrogel into the organohydrogel with remarkably enhanced anti-drying and anti-freezing capacities and toughness, which effectively improved the long-time stability of the sensors. Importantly, we execute sound/light alarms and a wireless smartphone alarm by utilizing a designed circuit board and applet. This work gives an incisive investigation for the preparation, performance improvement, mechanism and application of hydrogel-based NO₂ sensors, promoting the evolution of hydrogel ionotronics.

Human Blood Platelets Adsorption on Polymeric Materials for Liquid Biopsy

Platelets are emerging as a promising source of blood biomarkers for several pathologies, including cancer. New automated techniques for easier manipulation of platelets in the context of lab-on-a-chips could be of great support for liquid biopsy. Here, several polymeric materials were investigated for their behavior in terms of adhesion and activation of human platelets. Polymeric materials were selected among the most used in microfabrication (PDMS, PMMA and COC) and commercial and home-made resins for 3D printing technology with the aim to identify the most suitable for the realization of microdevices for human platelets isolation and analysis. To visualize adherent platelets and their activation state scanning, electron microscopy was used, while confocal microscopy was used for evaluating platelets’ features. In addition, atomic force microscopy was employed to further study platelets adherent to the polymeric materials. Polymers were divided in two main groups: the most prone to platelet adhesion and materials that cause few or no platelets to adhere. Therefore, different polymeric materials could be identified as suitable for the realization of microdevices aimed at capturing human platelets, while other materials could be employed for the fabrication of microdevices or parts of microdevices for the processing of platelets, without loss on surfaces during the process.

Copper Oxide/Functionalized Graphene Hybrid Nanostructures for Room Temperature Gas Sensing Applications

Oxide semiconductors are conventionally used as sensing materials in gas sensors, however, there are limitations on the detection of gases at room temperature (RT). In this work, a hybrid of copper oxide (CuO) with functionalized graphene (rGO) is proposed to achieve gas sensing at RT. The combination of a high surface area and the presence of many functional groups in the CuO/rGO hybrid material makes it highly sensitive for gas absorption and desorption. To prepare the hybrid material, a copper oxide suspension synthesized using a copper acetate precursor is added to a graphene oxide solution during its reduction using ascorbic acid. Material properties of the CuO/rGO hybrid and its drop-casted thin-films are investigated using Raman, FTIR, SEM, TEM, and four-point probe measurement systems. We found that the hybrid material was enriched with oxygen functional groups (OFGs) and defective sites, along with good electrical conductivity (Sheet resistance~1.5 kΩ/□). The fabricated QCM (quartz crystal microbalance) sensor with a thin layer of the CuO/rGO hybrid demonstrated a high sensing response which was twice the response of the rGO-based sensor for CO2 gas at RT. We believe that the CuO/rGO hybrid is highly suitable for existing and future gas sensors used for domestic and industrial safety.

An Overview on Recent Progress of the Hydrogels: From Material Resources, Properties to Functional Applications

Hydrogels, as the most typical elastomer materials with three-dimensional network structures, have attracted wide attention owing to their outstanding features in fields of sensitive stimulus response, low surface friction coefficient, good flexibility and bio-compatibility. Because of numerous fresh polymer materials (or polymerization monomers), hydrogels with various structure diversities and excellent properties are emerging, and the development of hydrogels is very vigorous over the past decade. This review focuses on state-of-the-art advances, systematically reviews the recent progress on construction of novel hydrogels utilized several kinds of typical polymerization monomers, and explores the main chemical and physical cross-linking methods to develop the diversity of hydrogels. Following the aspects mentioned above, the classification and emerging applications of hydrogels, such as pH response, ionic response, electrical response, thermal response, biomolecular response, and gas response, are extensively summarized. Finally, we have done this review with the promises and challenges for the future evolution of hydrogels and their biological applications. cross-linking methods; functional applications; hydrogels; material resources This article is protected by copyright. All rights reserved.

Overview of Quartz Crystal Microbalance Behavior Analysis and Measurement

Quartz Crystal Microbalance (QCM) is one of the many acoustic transducers. It is the most popular and widely used acoustic transducer for sensor applications. It has found wide applications in chemical and biosensing fields owing to its high sensitivity, robustness, small sized-design, and ease of integration with electronic measurement systems. However, it is necessary to coat QCM with a sensing film. Without coating materials, its selectivity and sensitivity are not obtained. At present, this is not an issue, mainly due to the advancement of oscillator circuits and dedicated measurement circuits. Since a new researcher may seek to understand QCM sensors, we provide an overview of QCM from its fundamental knowledge. Then, we explain some of the recent QCM applications both in gas-phase and liquid-phase. Next, the theory of QCM is introduced by using piezoelectric stress equations and the Mason equivalent circuit, which explains how the QCM behavior is obtained. Then, the conventional equations that govern QCM behaviors in terms of resonant frequency and resistance are described. We show the behavior of QCM with a viscous film based on the acoustic wave equation and Mason equivalent circuit. Then, we present various existing QCM electronic measurement methods. Furthermore, we describe the experiment on QCM with viscous loading and its interpretation based on the Mason equivalent circuit. Lastly, we review some theoretical models to describe QCM behavior with various models.

Ion-Conductive Hydrogel-Based Stretchable, Self-Healing, and Transparent NO2 Sensor with High Sensitivity and Selectivity at Room Temperature

Here stretchable, self-healable, and transparent gas sensors based on salt-infiltrated hydrogels for high-performance NO₂ sensing in both anaerobic environment and air at room temperature, are reported. The salt-infiltrated hydrogel displays high sensitivity to NO₂ (119.9%/ppm), short response and recovery time (29.8 and 41.0 s, respectively), good linearity, low theoretical limit of detection (LOD) of 86 ppt, high selectivity, stability, and conductivity. A new gas sensing mechanism based on redox reactions occurring at the electrode-hydrogel interface is proposed to understand the sensing behaviors. The gas sensing performance of hydrogel is greatly improved by incorporating calcium chloride (CaCl₂ ) in the hydrogel via a facile salt-infiltration strategy, leading to a higher sensitivity (2.32 times) and much lower LOD (0.06 times). Notably, both the gas sensing ability, conductivity, and mechanical deformability of hydrogels are readily self-healable after cutting off and reconnection. Such large deformations as 100% strain do not deprive the gas sensing capability, but rather shorten the response and recovery time significantly. The CaCl₂ -infiltrated hydrogel shows excellent selectivity of NO₂ , with good immunity to the interference gases. These results indicate that the salt-infiltrated hydrogel has great potential for wearable electronics equipped with gas sensing capability in both anaerobic and aerobic environments.