Extraction of nanocellulose fibrils from lignocellulosic fibres: A novel approach

Potential of Plantain Pseudostems (Musa AAB Simmonds) for Developing Biobased Composite Materials

A plantain pseudostem was harvested and processed on the same day. The process began with manually separating the sheaths (80.85%) and the core (19.14%). The sheaths were subjected to a mechanical shredding process using paddles, extracting 2.20% of lignocellulosic fibers and 2.12% of sap, compared to the fresh weight of the sheaths. The fibers were washed, dried, combed, and spun in their native state and subjected to a steam explosion treatment, while the sap was subjected to filtration and evaporation. In the case of the core, it was subjected to manual cutting, drying, grinding, and sieving to separate 12.81% of the starch and 6.39% of the short lignocellulosic fibers, compared to the fresh weight of the core. The surface modification method using steam explosion succeeded in removing a low proportion of hemicellulose and lignin in the fibers coming from the shims, according to what was shown by Fourier Transform Infrared Spectroscopy (FT-IR), Thermogravimetric Analysis (TGA), and Differential Scanning Calorimetry (DSC), achieving increased σmax and ε from the tensile test and greater thermal stability compared to its native state. The sap presented hygroscopic behavior by FT-IR and the highest thermal stability from TGA, while the starch from the core presented the lowest hygroscopic character and thermal stability. Although the pseudostem supplied two types of fibers, lower lignin content was identified in those from the core. Finally, the yarns were elaborated by using the fibers of the sheaths in their native and steam-exploded states, identifying differences in the processing and their respective physical and mechanical properties.

Nanocellulose-Based Hybrid Scaffolds for Skin and Bone Tissue Engineering: A 10-Year Overview

Cellulose, the most abundant polymer on Earth, has been widely utilized in its nanoform due to its excellent properties, finding applications across various scientific fields. As the demand for nanocellulose continues to rise and its ease of use becomes apparent, there has been a significant increase in research publications centered on this biomaterial. Nanocellulose, in its different forms, has shown tremendous promise as a tissue engineered scaffold for regeneration and repair. Particularly, nanocellulose-based composites and scaffolds have emerged as highly demanding materials for both soft and hard tissue engineering. Medical practitioners have traditionally relied on collagen and its analogue, gelatin, for treating tissue damage. However, the limited mechanical strength of these biopolymers restricts their direct use in various applications. This issue can be overcome by making hybrids of these biopolymers with nanocellulose. This review presents a comprehensive analysis of the recent and most relevant publications focusing on hybrid composites of collagen and gelatin with a specific emphasis on their combination with nanocellulose. While bone and skin tissue engineering represents two areas where a majority of researchers are concentrating their efforts, this review highlights the use of nanocellulose-based hybrids in these contexts.

Extraction and characterization of cellulose microfibers from cornhusk for application as reinforcing agent in biocomposite

This study aims to extract and characterize cellulose microfibers from cornhusk, an agricultural by-product. The extracted fibers will then be used as a reinforcing agent in a biocomposite made of thermoplastic corn starch. The process of extracting cellulose microfibers involved two treatments: sequential alkali treatment (using sodium hydroxide at 120 °C for 120 min) and peroxide bleach treatment (using hydrogen peroxide at 90 °C for 60 min). Various techniques such as Fourier transform infrared (FTIR), X-Ray diffraction (XRD), scanning electron microscopy (SEM), and thermogravimetric analysis (TGA) were employed to characterize the extracted fibers. The properties of the composite were examined through tensile strength tests, contact angle measurements, and UV-Vis spectrophotometry. The study found that cellulose microfibers were successfully extracted from cornhusks, with a diameter of 7 to 30 μm and a crystallinity of 65 %. The treated fibers showed gradual degradation between 150 °C and 350 °C, indicating a lower amount of non-cellulosic substances compared to untreated cornhusks. Adding 10 % of the microfibers to the thermoplastic starch composite increased the tensile stress at breaking and the Young's modulus, but decreased the contact angle of water droplets and the film's transparency.

Biodegradable films from the lignocellulosic fibers of wheat straw biomass and the effect of calcium ions

Plastics are hazardous to human health, and plastic waste results in environmental pollution and ecological catastrophe. Biobased polymers from renewable sources have recently become promising for developing biodegradable packaging films. Among them, lignocellulosic residue from agricultural biomass is inexpensive, renewable, and biodegradable. This study aims to develop biodegradable films using lignocellulosic residue from wheat straw biomass. The methodology is a green process that solubilizes lignocellulosic chains using Zn2+ ions and crosslinks with Ca2+ ions of different concentrations (200-800 mM). The results reveal that the increase of Ca2+ ions significantly decreases moisture content, water solubility, water vapor permeability, transparency, and elongation of films. The tensile strength is recorded as 6.61 ± 0.07 MPa with the addition of 800 mM of CaCl2, which is approximately 2.5 times higher than commercial polyethylene films. Around 90 % of films biodegrade within a month in soil containing 20 % moisture content. Overall, lignocellulosic residue from wheat straw biomass could be an excellent replacement for synthetic polymer to fabricate strong, transparent, and biodegradable plastic films.

A Versatile Shaping Method of Very-High Loading Porous Solids Paper Adsorbent Composites

Owing to their high porosity and tunability, porous solids such as metal-organic frameworks (MOFs), zeolites, or activated carbons (ACs) are of great interest in the fields of air purification, gas separation, and catalysis, among others. Nonetheless, these materials are usually synthetized as powders and need to be shaped in a more practical way that does not modify their intrinsic property (i.e., porosity). Elaborating porous, freestanding and flexible sheets is a relevant shaping strategy. However, when high loadings (>70 wt.%) are achieved the mechanical properties are challenged. A new straightforward and green method involving the combination softwood bleached kraft pulp fibers (S) and nano-fibrillated cellulose (NFC) is reported, where S provides flexibility while NFC acts as a micro-structuring and mechanical reinforcement agent to form high loadings porous solids paper sheets (>70 wt.%). The composite has unobstructed porosity and good mechanical strength. The sheets prepared with various fillers (MOFs, ACs, and zeolites) can be rolled, handled, and adapted to different uses, such as air purification. As an example of potential application, a MOF paper composite has been considered for the capture of polar volatile organic compounds exhibiting better performance than beads and granules.

Bio-based Pickering emulsifier from mangosteen residues-derived sodium caseinate grafted spherical cellulose nanocrystals: Stability, rheological properties and microstructure studies

This study focuses on the preparation of mangosteen rind-derived nanocellulose via green ascorbic acid hydrolysis. Subsequently, milk protein-grafted nanocellulose particles were developed as a renewable Pickering emulsifier for water-oil stabilization. The stabilizing efficiency of modified nanocellulose (NC-S) at different caseinate (milk protein) concentrations (1.5, 3.0, and 4.0 % w/v) was tested in a water-in-oil emulsion (W/O ratio of 40:60). At a concentration 3.0 % w/v of caseinate (3.0NC-S), the emulsion exhibited a stronger network of adsorption between water, Pickering emulsifier, and oil. This resulted in reduced oil droplet flocculation, increased stability over a longer period, and favorable emulsifying properties, as depicted in the creaming index profile, oil droplet distribution, and rheology analysis. Since 3.0NC-S demonstrated the best colloidal stability, further focus will be placed on its microstructural properties, comparing them with those of mangosteen rind (MG), cellulose, and nanocellulose (NC-L). The XRD profile indicated that both NC-L and NC-S possessed a cellulose nanocrystal structure characterized as type I beta with a high crystallinity index above 60 %. Morphology investigation shown that the NC-L present in the spherical shape of particles with nanosized ranging at diameters of 11.27 ± 0.50 nm and length 11.76 ± 0.46 nm, while modified NC-S showed increase sized at 14.26 ± 4.60 nm and length 14.96 ± 4.94 nm. The increment of particle sizes from NC-L to NC-S indicated 2.82 × 10-15 mg/m2 of surface protein coverage by caseinate functional groups.

Preparation of nanocellulose and its applications in wound dressing: A review

Nanocellulose, as a nanoscale polymer material, has garnered significant attention worldwide due to its numerous advantages including excellent biocompatibility, thermal stability, non-toxicity, large specific surface area, and good hydrophilicity. Various methods can be employed for the preparation of nanocellulose. Traditional approaches such as mechanical, chemical, and biological methods possess their own distinct characteristics and limitations. However, with the growing deterioration of our living environment, several green and environmentally friendly preparation techniques have emerged. These novel approaches adopt eco-friendly technologies or employ green reagents to achieve environmental sustainability. Simultaneously, there is a current research focus on optimizing traditional nanocellulose preparation methods while addressing their inherent drawbacks. The combination of mechanical and chemical methods compensates for the limitations associated with using either method alone. Nanocellulose is widely used in wound dressings owing to its exceptional properties, which can accelerate the wound healing process and reduce patient discomfort. In this paper, the principle, advantages and disadvantages of each preparation method of nanocellulose and the research findings in recent years are introduced Moreover, this review provides an overview of the utilization of nanocellulose in wound dressing applications. Finally, the prospective trends in its development alongside corresponding preparation techniques are discussed.

Nanocellulose: A comprehensive review investigating its potential as an innovative material for water remediation

Rapid growth in industrialization sectors, the wastewater treatment plants become exhausted and potentially not able to give desirable discharge standards. Many industries discharge the untreated effluent into the water bodies which affects the aquatic diversity and human health. The effective disposal of industrial effluents thus has been an imperative requirement. For decades nanocellulose based materials gained immense attraction towards application in wastewater remediation and emerged out as a new biobased nanomaterial. It is light weighted, cost effective, mechanically strong and easily available. Large surface area, versatile surface functionality, biodegradability, high aspect ratio etc., make them suitable candidate in this field. Majorly cellulose based nanomaterials are used in the form of cellulose nanocrystals (CNCs), cellulose nanofibers (CNFs), or bacterial nanocellulose (BNC). This review specifically describes about a variety of extraction methods to produced nanocellulose and also discusses the modification of nanocellulose by adding functionalities in its surface chemistry. We majorly focus on the utilization of nanocellulose based materials in water remediation for the removal of different contaminants such as dyes, heavy metals, oil, microbial colony etc. This review mainly emphasizes in ray of hope towards nanocellulose materials to achieve more advancement in the water remediation fields.

Effect of chitosan-based bio coating on mechanical, structural and physical characteristics of microfiber based paper packaging: An alternative to wood pulp/plastic packaging

Limnocharis flava is a noxious aquatic weed that poses a threat to paddy cultivation. The high cellulose and low lignin contents in this plant make it a potential raw material for papermaking. Against this backdrop, this study was taken up to develop Limnocharis flava (LF) based sheets containing natural fibres from Banana (B), Pineapple (P), and Rice Straw (RS) as reinforcing agents. The influence of carboxymethyl cellulose (CMC) as a binder on the LF-based sheets was also studied. To enhance the mechanical and moisture resistance properties, a chitosan coating was provided to the sheets. Analytical tests for mechanical properties, water barrier properties, functional groups, structure and microstructure, thermal properties and biodegradability were performed. Among the samples, LF + B showed the highest tensile strength (34.86 Mpa) and bursting strength (13.055 kg/cm2), while LF + R had higher puncture and tearing strengths. Chitosan coating was found to enhance the sheets and improve the water barrier properties mechanically. The contact angle of LF + B increased from 91.6° to 110.65°, while the water vapour transmission rate of LF reduced from 532.18 to 404.47 on providing chitosan coating. The significant interactions of reinforcing agents were confirmed by the results of FTIR and that of the coating by the SEM micrographs. The LF-based sheets were also found to have decent thermal stability. The high value of the crystallinity index in LF + R samples supported their remarkable mechanical properties. This study proclaims the notable suitability of Limnocharis flava in manufacturing paper for packaging applications.

Biodegradation of polysaccharide-based biocomposites with acetylated cellulose nanocrystals, alginate and chitosan in aqueous environment

Biocomposite films from renewable sources are seen to be viable candidates as sustainable, zero-waste packaging materials. In this study, biocomposites films using chitosan and alginate as matrices, and pristine or acetylated cellulose nanocrystals (CNCs) as reinforcement agents, were fabricated, thoroughly characterized in terms of structure (with ATR-FTIR and XRD), morphology (SEM), thermal stability (TGA coupled with FTIR), water content and solubility and mechanical properties and subjected to controlled biological degradation in aqueous environment with added activated sludge. Biodegradation activity was followed through respirometry by measurement of change in partial O2 pressure using OxiTop® system. While the initial rate of biodegradation is higher in chitosan-based films with incorporated CNCs (both pristine and modified) compared to any other tested biocomposites, it was observed that chitosan-based films are not completely degradable in activated sludge medium, whereas alginate-based films reached complete biodegradation in 107 h to 112 h. Additional study of the aqueous medium with in situ FTIR during biodegradation offered an insight into biodegradation mechanisms. Use of advanced statistical methods indicated that selection of material (ALG vs CH) has the highest influence on biodegradability, followed by solubility of the material and its thermal stability.

Optimized high-yield synthesis of chitin nanocrystals from shrimp shell chitin by steam explosion

This study attempted for the first time to prepare chitin nanocrystals (ChNCs) from shrimp shell chitin using steam explosion (SE) method. Response surface methodology (RSM) approach was used to optimize the SE conditions. Optimum SE conditions to acquire a maximum yield of 76.78 % were acid concentration (2.63 N), time (23.70 min), and chitin to acid ratio (1:22). Transmission electron microscopy (TEM) revealed the ChNCs produced by SE had an irregular spherical shape with an average diameter of 55.70 ± 13.12 nm. FTIR spectra showed ChNCs were slightly different than chitin due to a shift in peak positions to higher wavenumber and higher peak intensities. XRD patterns indicated ChNCs were a typical α-chitin structure. Thermal analysis revealed ChNCs were less thermally stable than chitin. Compared to conventional acid hydrolysis, the SE approach described in this study is simple, fast, easy, and requires less acid concentration and acid quantity, making it more scalable and efficient for synthesizing ChNCs. Furthermore, the characteristics of the ChNCs will shed light on the potential industrial uses for the polymer.

Green synthesis of sulfonated cellulose/polyether block amide/polyethylene glycol diacrylate (SC/PEBAX/PEGDA) composite membrane by gamma radiation and sulfonation techniques for battery application

Sulfonated cellulose (SC) was successfully prepared through a two-step process of gamma radiation and subsequently sulfonation with potassium metabisulfite of microcrystalline cellulose extracted from sugarcane bagasse. The effect of gamma radiation dose on cellulose showed an increment of oxidation degree, which was evidenced by the intensity ratio of I1718 (carbonyl)/ I2892 (aliphatic) from FTIR analysis. The obtained SC was introduced into polyether block amide/polyethylene glycol diacrylate (PEBAX/PEGDA) polymer matrix as a reinforcement and hydrophilic filler for improving electrolyte affinity and thermal stability of its composite membrane. The increase of SC in PEBAX/PEGDA composite membranes resulted in enhancement of hydrophilicity, electrolyte uptake, and thermal stability compared to pristine composite membranes. However, the excess SC content in the composite membrane exhibited the low physical properties, caused by negligible dispersion on the surface membrane. With the optimum 2.0 wt% SC in PEBAX/PEGDA, the porosity, contact angle and electrolyte uptake capacity was found to be 64.0 %, 12.8° and 37.5 %, respectively. 2.0 wt% SC/PEBAX/PEGDA showed the outstanding thermal stability with negligible shrinkage <10 % at 150 °C whereas pristine PEBAX/PEGDA showed the shrinkage of 29 %. The obtained SC/PEBAX/PEGDA composite membrane is considered as a potential candidate to replace the commercial polyolefin-based separator in lithium-ion batteries.

Banana biomass waste: A prospective nanocellulose source and its potential application in food industry - A review

Bananas are among the most produced and consumed fruit all over the world. However, a vast amount of banana biomass is generated because banana trees bear fruit only once in their lifetime. This massive amount of biomass waste is either disposed of in agricultural fields, combusted, or dumped at plantations, thus posing environmental concerns. Nanocellulose (NC) extraction from this source can be one approach to improve the value of banana biomass. Owing to its superb properties, such as high surface area and aspect ratio, good tensile strength, and high thermal stability, this has facilitated nanocellulose application in the food industry either as a functional ingredient, an additive or in food packaging. In this review, two different applications of banana biomass NC were identified: (i) food packaging and (ii) food stabilizers. Relevant publications were reviewed, focusing on the nanocellulose extraction from several banana biomass applications as food additives, as well as on the safety and regulatory aspects. Ultimately, further research is required to prompt a perspicuous conclusion about banana biomass NC safety, its potential hazards in food applications, as well as its validated standards for future commercialization.

Ballistic Performance, Thermal and Chemical Characterization of Ubim Fiber (Geonoma baculifera) Reinforced Epoxy Matrix Composites

The search for unexplored natural materials as an alternative to synthetic components has driven the development of novel polymeric composites reinforced with environmentally-friendly materials. Natural lignocellulosic fibers (NLFs) have been highlighted as potential reinforcement in composite materials for engineering applications. In this work, a less known Amazonian fiber, the ubim fiber (Geonoma baculifera), is investigated as a possible reinforcement in epoxy composites and was, for the first time, thermally characterized by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). Additionally, its chemical structure was elucidated by Fourier transform infrared spectroscopy (FTIR). Ballistic tests were also performed against the threat of a 7.62 mm high-speed lead projectile. The results were statistically analyzed by the Weibull statistical analysis method. FTIR analysis showed the functional groups normally found for NLFs highly rich in cellulose, hemicellulose, and lignin. The TGA/DTG results showed the onset of thermal degradation for the composites (325~335 °C), which represents better thermal stability than isolated ubim fiber (259 °C), but slightly lower than that of pure epoxy (352 °C). The DSC results of the composites indicate endothermic peaks between 54 and 56 °C, and for the ubim fibers, at 71 °C. Ballistic tests revealed higher energy absorption in composites with lower fiber content due to the more intense action of the brittle fracture mechanisms of the epoxy resin, which tended to dissipate more energy. These failure mechanisms revealed the presence of river marks, cracks, and broken fibers with a detachment interface. These results may contribute to the production of ubim fiber-reinforced composites in engineering applications, such as ballistic armors.

Production and characterization of nanofibrillated cellulose gels simultaneously exhibiting thermally stable green color and oil-in-water emulsion stabilizing capability from Centella asiatica

Nanofibrillated cellulose (NFC) gels simultaneously exhibiting Pickering stabilizing capability and thermally stable green color were developed for use as food additive in thermally processed food emulsion requiring the expression of color. Chopped Centella asiatica plant was mixed with zinc amino acid chelate solution and subject to autoclaving at 130°C for 2 h to form zinc-chlorophylls complex and to remove noncellulosic components. Autoclaved sample was high-shear homogenized at 26,000 rpm for 15 min and microfluidized at either 80, 120, or 160 MPa for 5 passes. An increase in microfluidization pressure resulted in a decrease in NFC diameters; microfluidization at 160 MPa did not nevertheless yield any further reduction in the diameters when compared with that at 120 MPa. From energy consumption point of view, microfluidization at 120 MPa for 5 passes was then noted as optimal condition for preparation of NFC coloring gel; NFC with diameters of 8-42 nm and crystallinity index of 35% was obtained. Freshly prepared gel exhibited gel-like behavior and dark green color. Heating at 121°C for 1 h did not affect diameters, viscoelasticity, and color of the gel. Addition of the gel at 0.9% or 1.2% (w/w) into soybean oil-in-water emulsion, in combination with high-shear homogenization at 18,000 rpm for 5 min, resulted in adequate emulsion stability. The emulsion exhibited stable dark green color and no phase separation after heating at 121°C for 1 h and during storage for 8 weeks. PRACTICAL APPLICATIONS: Information presented here can serve as a guideline for further development of a multifunctional food ingredient exhibiting thermally stable green color and oil-in-water emulsion stabilizing capability. In other words, one simple ingredient can serve at the same time as both natural food colorant and emulsion stabilizer.

Biosynthesis of cellulose from Ulva lactuca, manufacture of nanocellulose and its application as antimicrobial polymer

Green nanotechnology has recently been recognized as a more proper and safer tool for medical applications thanks to its natural reductions with low toxicity and avoidance of injurious chemicals. The macroalgal biomass was used for nanocellulose biosynthesis. Algae are abundant in the environment and have a high content of cellulose. In our study, we extracted parent cellulose from Ulva lactuca where consecutive treatments extracted cellulose to obtain an insoluble fraction rich in cellulose. The extracted cellulose has the same results obtained by matching it with reference cellulose, especially the same Fourier transform infrared (FTIR) and X-Ray diffraction (XRD) analysis peaks. Nanocellulose was synthesized from extracted cellulose with hydrolysis by sulfuric acid. Nanocellulose was examined by Scanning electron microscope (SEM) shown by a slab-like region as Fig. 4a and Energy dispersive X-ray (EDX) to examine the chemical composition. The size of nanocellulose in the range of 50 nm is calculated by XRD analysis. Antibacterial examination of nanocellulose was tested against Gram+ bacteria like Staphylococcus aureus (ATCC6538), Klebsiella pneumonia (ST627), and Gram-negative bacteria such as Escherichia coli (ATCC25922), and coagulase-negative Staphylococci (CoNS) to give 4.06, 4.66, 4.93 and 4.43 cm as respectively. Comparing the antibacterial effect of nanocellulose with some antibiotics and estimating minimal Inhibitory Concentration (MIC) of nanocellulose. We tested the influence of cellulose and nanocellulose on some fungi such as Aspergillus flavus, Candida albicans, and Candida tropicalis. These results demonstrate that nanocellulose could be developed as an excellent solution to these challenges, making nanocellulose extracted from natural algae a very important medical material that is compatible with sustainable development.

Preparation and Adsorption Properties of Lignin/Cellulose Hydrogel

With the development of global industry, industrial wastewater pollution has caused serious environmental problems, and the demand for green and sustainable adsorbents is increasingly strong in the society. In this article, lignin/cellulose hydrogel materials were prepared using sodium lignosulfonate and cellulose as raw materials and 0.1% acetic acid solution as a solvent. The results showed that the optimal adsorption conditions for Congo red were as follows: an adsorption time of 4 h, a pH value of 6, and an adsorption temperature of 45 °C. The adsorption process was in line with the Langmuir isothermal model and a quasi-second-order kinetic model, which belonged to single molecular layer adsorption, and the maximum adsorption capacity was 294.0 mg/g. The optimal adsorption conditions for Malachite green were as follows: an adsorption time of 4 h, a pH value of 4, and an adsorption temperature of 60 °C. The adsorption process was consistent with the Freundlich isothermal model and a pseudo-second-order kinetic model, which belonged to the chemisorption-dominated multimolecular layer adsorption with the maximum adsorption capacity of 129.8 mg/g.

An efficient approach to extract nanocrystalline cellulose from sisal fibers: Structural, morphological, thermal and antibacterial analysis

Nanocellulose has been proposed by many researchers as a suitable bio-reinforcement material for the development of sustainable bio-nanocomposites in advanced applications due to its excellent properties. Conventional techniques for extracting nanocellulose from plant biomass are time-consuming and involve chemical wastage. This study aims to extract nanocellulose using simple processes with minimal consumption of chemicals in a minimum time. In the present work, cellulose nanocrystalline has been extracted from sisal fibers efficiently by chemical treatment assisted with steam explosion and mechanical grinding. The morphology of extracted sisal cellulose nanocrystalline (CNC-S) was analyzed by FESEM, whereas the DLS, TEM and AFM confirmed its nanosize. The average aspect ratio and zeta potential (ζ) of CNC-S were measured as 7.4 and -14.3 mV, respectively. The XRD analysis indicated that the crystallinity of the fibers considerably improved from 48.74 % for untreated fibers (UT-S) to 74.28 % for CNC-S. The chemical structure of the fibers was changed as hemicellulose and lignin were found to be eliminated after the chemical treatment which FTIR confirmed. From TGA-DTG results, it was observed that CNC-S has good thermal stability. It was also noticed that CNC-S did not show any antibacterial properties against E. coli and S. aureus due to the complete removal of lignin. This study suggests that the present extraction process can be considered as an efficient process to convert fibers into high performance nanocellulose to be used as potential reinforcing material in advanced applications.

Understanding Nanocellulose-Water Interactions: Turning a Detriment into an Asset

Modern technology has enabled the isolation of nanocellulose from plant-based fibers, and the current trend focuses on utilizing nanocellulose in a broad range of sustainable materials applications. Water is generally seen as a detrimental component when in contact with nanocellulose-based materials, just like it is harmful for traditional cellulosic materials such as paper or cardboard. However, water is an integral component in plants, and many applications of nanocellulose already accept the presence of water or make use of it. This review gives a comprehensive account of nanocellulose-water interactions and their repercussions in all key areas of contemporary research: fundamental physical chemistry, chemical modification of nanocellulose, materials applications, and analytical methods to map the water interactions and the effect of water on a nanocellulose matrix.

Experimental study on evaluation and optimization of heavy metals adsorption on a novel amidoximated silane functionalized Luffa cylindrica

This study aimed to synthesize an amidoximated Luffa cylindrica (AO-LC) bioadsorbent, and evaluate its efficiency in the adsorption of heavy metals from the aqueous solutions. For this purpose, NaOH solution was used to alkaline treatment of Luffa cylindrica (LC) fibers. The silane modification of LC was performed using 3-(trimethoxysilyl)propyl methacrylate (MPS). Polyacrylonitrile (PAN)/LC biocomposite (PAN-LC) was synthesized by PAN grafting onto the MPS-modified LC (MPS-LC). Finally, the AO-LC was obtained by the amidoximation of PAN-LC. The chemical structures, morphology, and thermal properties of biocomposites were characterized by the infrared spectroscopy, X-ray diffraction, thermogravimetric analysis, and field emission scanning electron microscopy. The results showed a successful grafting of MPS and PAN on the surface of LC. The order of heavy metals adsorption on AO-LC was: Pb²⁺ > Ag⁺ > Cu²⁺ > Cd²⁺ > Co²⁺ > Ni²⁺. The effects of operational parameters on the Pb²⁺ adsorption were studied using Taguchi experimental design method. Statistical analysis of the results showed that the initial Pb²⁺ concentration and the bioadsorbent dosage significantly affect the adsorption efficiency. The adsorption capacity and removal percentage of Pb²⁺ ions were obtained as 18.88 mg/g and 99.07%, respectively. The Langmuir isotherm and Pseudo-second order kinetics models were found to be better compatible with experimental data as a consequence of the isotherm and kinetics analysis.

Effects of ultrasonic-assisted pH shift treatment on physicochemical properties of electrospinning nanofibers made from rapeseed protein isolates

Electrospinning nanofibers (NFs) made from natural proteins have drawn increasing attention recently. Rapeseed meal is a by-product that rich in protein but not fully utilized due to poor properties. Therefore, modification of rapeseed protein isolates (RPI) is necessary to expand applications. In this study, pH shift alone or ultrasonic-assisted pH shift treatment was adopted, the solubility of RPI, along with the conductivity and viscosity of the electrospinning solution were detected. Moreover, the microstructure and functional characteristics of the electrospinning NFs, as well as the antibacterial activity of clove essential oil loaded-NFs were investigated. The tested parameters were remarkably improved after different treatments compared with the control, and synergistic effects were observed, especially under alkaline conditions. Hence, pH_12.5 + US showed the maximum value of solubility, conductivity, and viscosity, which was more than 7-fold, 3-fold, and almost 1-fold higher than the control respectively. Additionally, SEM and AFM images showed a finer and smoother surface of NFs after treatments, and the finest diameter of 216.7 nm was obtained after pH_12.5 + US treatment in comparison with 450.0 nm in control. FTIR spectroscopy of NFs demonstrated spatial structure changes of RPI, and improved thermal stability and mechanical strength of NFs were achieved after different treatments. Furthermore, an inhibition zone with a diameter of 22.8 mm was observed from the composite NFs. This study indicated the effectiveness of ultrasonic-assisted pH shift treatment on the physicochemical properties improvement and functional enhancement of NFs made from RPI, as well as the potential antibacterial application of the composite NFs in the future.

Nanocellulose reinforced lightweight composites produced from cotton waste via integrated nanofibrillation and compounding

Cotton is a natural fiber containing more than 95% of cellulose. With worldwide cotton consumption continuously increasing, the amount of cotton waste generated is enormous. Most of the cotton waste ends up in landfill or incinerators, resulting in a huge waste of this excellent natural resource. In this project, cotton waste was recycled to produce polypropylene nanocomposites. Instead of using the traditional two-step nanofiber extraction and compounding technique, an integrated process was adopted to combine nanofibrillation and compounding into one step. Results showed that cotton fibers with a slight prefibrillation and hydrophobic surface modification were successfully fibrillated into tens to hundreds of nanometers in width during compounding. The nanofibers reinforced polypropylene composites exhibited significantly enhanced tensile and flexural strength and moduli. For instance, when 30% fibers from bleached white and indigo-dyed denim fabrics were introduced, the tensile moduli of the resultant composites reached 4.57 and 4.59 GPa, respectively, compared to 1.60 GPa, the modulus of neat PP. Meanwhile, denim fabrics had a remarkable reinforcing effect on the composites' impact strength attributing to the hydrophobic indigo dyes that improved the interfacial bonding between cotton fibers and the matrix. The highest impact strength of denim reinforced composites was 4.96 kJ/m² with 20% fiber loading; while the impact strength of neat polypropylene was 2.46 kJ/m². The low water uptake of the composites further indicated the excellent adhesion at the filler/matrix interface. In general, a very promising processing technique to recycle cotton waste for high-value products was demonstrated.

Characteristics and Functional Application of Cellulose Fibers Extracted from Cow Dung Wastes

The widespread use of petroleum-based products has led to increasing environmental and ecological problems, while the extraction and application of various natural cellulose fibers have received increasing attention. This research focuses on the extraction of cellulose fibers from cow dung using different treatments: hot water, hydrogen peroxide (H₂O₂), sodium hydroxide (NaOH) and potassium hydroxide (KOH) boilings, as well as a selection of the best quality cow dung fibers for papermaking with quality control. The study's objective is to find a sustainable method to extract as much material as possible from renewable biomass feedstock. The results show that the best extraction rate is obtained by KOH boiling with 42% cellulose fibers extracted. Corresponding handmade paper has a burst index of 2.48 KPam²/g, a tear index of 4.83 mNm²/g and a tensile index of 26.72 Nm/g. This project expands the sources of natural cellulose fibers to an eco-friendly and sustainable one and opens up new applications for cow dung.

Development of New Bio-Composite of PEO/Silk Fibroin Blends Loaded with Piezoelectric Material

New bio-composite nanofibers composed of polyethylene oxide (PEO)/silk fibroin (SF)/barium titanate (BaTiO₃) are introduced in this study. The SF solution was added to the PEO solution to form a PEO/SF blend with different weight percentages (5, 10, 15, 20 wt.%). The PEO/15 wt.% SF blend was selected to continue the experimental plan based on the optimum nanofiber morphology. Different wt.% of BaTiO₃ particles (0.2, 0.4, 0.8, 1 wt.%) were added to the PEO/15 wt.% SF blend solution, and the suspensions obtained were introduced to an electrospinning device. The fabricated tissue was characterized by scanning electron microscope (SEM), X-ray diffraction (XRD) and Fourier-transform infrared (FTIR) spectroscopy. The zeta potential of the solution and the piezoelectric performance of the fabricated tissue were characterized. A newly designed pizoTester was used to investigate piezoelectric properties. The results showed that a well-organized, smooth PEO/15 wt.% SF/0.2 wt.% BaTiO₃ nanofiber composite with low bead contents was obtained. Improved properties and electrical coupling were achieved in the newly introduced material. Electrospun PEO/15 wt.% SF/0.2 wt.% BaTiO₃ mats increased the output voltage (1150 mV) compared to pristine PEO and PEO/SF composite fibers (410 and 290 mV, respectively) upon applying 20 N force at 5 Hz frequency. The observed enhancement in piezoelectric properties suggests that the prepared composite could be a promising material in cardiac tissue engineering (CTE).

Nanocellulose-Based Nanocomposites for Sustainable Applications: A Review

Nanocellulose has emerged in recent years as one of the most notable green materials available due to its numerous appealing factors, including its non-toxic nature, biodegradability, high aspect ratio, superior mechanical capabilities, remarkable optical properties, anisotropic shape, high mechanical strength, excellent biocompatibility and tailorable surface chemistry. It is proving to be a promising material in a range of applications pertinent to the material engineering to biomedical applications. In this review, recent advances in the preparation, modification, and emerging application of nanocellulose, especially cellulose nanocrystals (CNCs), are described and discussed based on the analysis of the latest investigations. This review presents an overview of general concepts in nanocellulose-based nanocomposites for sustainable applications. Beginning with a brief introduction of cellulose, nanocellulose sources, structural characteristics and the extraction process for those new to the area, we go on to more in-depth content. Following that, the research on techniques used to modify the surface properties of nanocellulose by functionalizing surface hydroxyl groups to impart desirable hydrophilic-hydrophobic balance, as well as their characteristics and functionalization strategies, were explained. The usage of nanocellulose in nanocomposites in versatile fields, as well as novel and foreseen markets of nanocellulose products, are also discussed. Finally, the difficulties, challenges and prospects of materials based on nanocellulose are then discussed in the last section for readers searching for future high-end eco-friendly functional materials.

Copaiba oil and vegetal tannin as functionalizing agents for açai nanofibril films: valorization of forest wastes from Amazonia

The applicability of cellulose nanofibrils (CNFs) has received attention due to their attractive properties. This study proposes the functionalization of açai CNFs with copaiba oil and vegetal tannins to produce films with potential for packaging. Bio-based films were evaluated by vapor permeability, colorimetry, and mechanical strength. CNFs were produced by mechanical fibrillation, from suspensions of bleached açai fibers and commercial eucalipytus pulp. Moreover, copaiba oil and vegetal tannin were added to the CNFs to produce films/nanopapers by casting from both suspensions with concentrations of 1% (based on CNF dry mass). The bulk densities of the eucalyptus CNF films were higher (1.126-1.171 g cm^-3) compared to the açai CNF ones. Films from eucalyptus and açai pulps containing copaiba oil and tannins presented higher Tonset and Tmax, respectively (312 and 370 °C). Films with açaí CNFs functionalized with copaiba oil and tannin showed the lowest permeability value (370 g day^-1 m^-2). Films produced with eucalyptus pulp, and eucalyptus pulp functionalized with copaiba oil highlighted by superior mechanical strength, achieving 133.8 and 121.4 MPa, respectively. The evaluation of colorimetry showed a greater tendency to yellowing for açai films, especially those functionalized with vegetal tannins. Besides the low cost, functionalized vegetal-based nanomaterials could have attractive properties, with potential for application as some kind of packaging, for transporting basic products, such as breads, flours, or products with low moisture content, enabling efficient utilization of forest wastes.

Effects of enzyme-assisted ultrasonic treatment to the properties of nanofibrils isolated from wheat straw

This study aimed to prepare cellulose nanofibrils (CNF) with tunable morphology and properties from wheat straw using enzyme-assisted ultrasonic treatment. The effects of different enzymatic hydrolysis duration on the morphology and the properties of the CNF were studied. The effects of different enzymatic hydrolysis duration on the morphology and the properties of the CNF were studied. AFM analysis showed that average height distribution for CNF-0 (without enzymatic pretreatment) decreased from 11.86 to 8.18 nm for CNF-4 (with the enzymatic hydrolysis duration of 4 h), while the crystallinity and water reserve value (WRV) for CNF-0 increased from 36 and 485% to 47 and 789% for CNF-4, respectively. The transmittance, wettability properties, and mechanical performances of CNF-based films were systematically studied. The results show that the film properties are highly dependent on the morphology of their corresponding CNF and can be effectively modulated by controlling the structural characteristics of CNF. The discoveries of this study provide an environment-friendly approach for the production of CNF with tunable morphology and fibril size, which can promote the production of cellulose-based nanomaterial as well as their related applications.

Molecular Insight into the Self-Assembly Process of Cellulose Iβ Microfibril

The self-assembly process of β-D-glucose oligomers on the surface of cellulose Iβ microfibril involves crystallization, and this process is analyzed herein, in terms of the length and flexibility of the oligomer chain, by means of molecular dynamics (MD) simulations. The characterization of this process involves the structural relaxation of the oligomer, the recognition of the cellulose I microfibril, and the formation of several hydrogen bonds (HBs). This process is monitored on the basis of the changes in non-bonded energies and the interaction with hydrophilic and hydrophobic crystal faces. The oligomer length is considered a parameter for capturing insight into the energy landscape and its stability in the bound form with the cellulose I microfibril. We notice that the oligomer–microfibril complexes are more stable by increasing the number of hydrogen bond interactions, which is consistent with a gain in electrostatic energy. Our studies highlight the interaction with hydrophilic crystal planes on the microfibril and the acceptor role of the flexible oligomers in HB formation. In addition, we study by MD simulation the interaction between a protofibril and the cellulose I microfibril in solution. In this case, the main interaction consists of the formation of hydrogen bonds between hydrophilic faces, and those HBs involve donor groups in the protofibril.

Grape stalk valorization for fermentation purposes

•

Integrated valorization of grape stalks generated lignin, fermentable sugars and nanocellulose.

•

For the first time, xylose was recover from grape stalk.

•

First cellulose nanocrystals recovered from grape stalk.

•

First proof of concept of use of a generated stream from an integrated valorization process.

•

Grape stalks fermentable sugars are consumed to produce bioethanol.

•

Biorefinery is a sustainable way for the processing of grape stalk.

White and red grape stalks biomass were fractioned to maximize its economic value by the production of fermentable sugars, as other value streams. High yields of extractives and lignin were first obtained, originating a biomass rich in cellulose and hemicellulose, which was subject to acid and enzymatic hydrolysis for production of fermentable sugars. Higher concentrations of sugars were obtained by enzymatic than by dilute acid hydrolysis. These biosugars were used for fermentation processes with Pichia stipitis and Saccharomyces cerevisiae. The presence of higher quantities of xylose favoured P. stipitis to produce higher ethanol yields than S. cerevisiae which is glucose lover. Cellulose nanocrystals were produced from the resulting biomass without monosaccharides. For the first time an integrated valorization of grape stalks followed by an application of one of the valorized streams is presented.

Anionic Dye Removal Using a Date Palm Seed-Derived Activated Carbon/Chitosan Polymer Microbead Biocomposite

The discharge of textile wastewater into aquatic streams is considered a major challenge due to its effect on the water ecosystem. Direct blue 78 (DB78) dye has a complex structure. Therefore, it is difficult to separate it from industrial wastewater. In this study, carbon obtained from the pyrolysis of mixed palm seeds under different temperatures (400 °C and 1000 °C) was activated by a thermochemical method by using microwave radiation and an HCl solution in order to improve its adsorption characteristics. The generated activated carbon was used to synthesize a novel activated carbon/chitosan microbead (ACMB) for dye removal from textile wastewater. The obtained activated carbon (AC) was characterized by a physicochemical analysis that included, namely, particle size, zeta potential, SEM, EDX, and FTIR analyses. A series of batch experiments were conducted in terms of the ACMB dose, contact time, pH, and activated carbon/chitosan ratios in synthetic microbeads for enhancing the adsorption capacity. A remarkable improvement in the surface roughness was observed using SEM analysis. The particle surface was transformed from a slick surface with a minor-pore structure to a rough surface with major-pore structure. The zeta potential analysis indicated a higher improvement in the carbon surface charge, from -35 mv (before activation) to +20 mv (after activation). The adsorption tests showed that the dye-removal efficiency increased with the increasing adsorbent concentration. The maximum removal efficiencies were 97.8% and 98.4% using 3 and 4 g/L of AC_400°C MB-0.3:1 and AC_1000°C MB-0.3:1, respectively, with initial dye concentrations of 40 mg/L under acidic conditions (pH = 4-5), and an optimal mixing time of 50 min. The equilibrium studies for AC_400°C MB-0.3:1 and AC_1000°C MB-0.3:1 showed that the equilibrium data best fitted to the Langmuir isothermal model with R² = 0.99. These results reveal that activated carbon/chitosan microbeads are an effective adsorbent for the removal of direct blue 78 dye and provide a new platform for dye removal.

Nanocellulose in tissue engineering and bioremediation: mechanism of action

Nanocellulose are nano-sized components which are biodegradable, biocompatible and renewable. It offers mechanical strength and chemical stability in plants and bacteria. The environmental contamination is reduced by employing various bioremediation techniques which usesmicroorganisms like algae, bacteria and fungi as bio-adsorbents. The bio adsorbent property of nanocellulose contribute more for the bioremediation methods and the detailed study of its mechanism and application is essential which is discussed here. The mechanism happening between the contaminant and nanocellulose adsorbent should be explored in detail in order to develop effective new bioremediation strategies. Nanocellulose structural functionalization helps to modify the nanocellulose structure based on which it can be utilized for specific functions. Exploring the mechanisms that contribute to the implementation of nanocellulose in tissue engineering helps for further developments and advancement in the biomedical application of nanocellulose. Not much studies are available that elucidate and study the basic steps involved in the biomedical and environmental usage of nanocellulose. This review has focussed on the basic mechanisms involved in the use of nanocellulose in tissue engineering and bioremediation processes.

Preparation of Cellulose Nanocrystals from Jujube Cores by Fractional Purification

Jujube cores are fiber-rich industrial waste. Dewaxing, alkali treatment, bleaching, and sulfuric acid hydrolysis were used to generate cellulose nanocrystals (CNCs) from the jujube cores in this study. The morphological, structural, crystallinity, and thermal properties of the fibers were investigated using FE-SEM, TEM, AFM, FT-IR, XRD, and TGA under various processes. CNCs’ zeta (ζ) potential and water contact angle (WAC) were also investigated. The findings demonstrate that non-fibrous components were effectively removed, and the fiber particles shrunk over time because of many activities. CNCs had a rod-like shape, with a length of 205.7 ± 52.4 nm and a 20.5 aspect ratio. The crystal structure of cellulose Iβ was preserved by the CNCs, and the crystallinity was 72.36%. The temperature of the fibers’ thermal degradation lowered during the operations, although CNCs still had outstanding thermal stability (>200 °C). Aside from the CNCs, the aqueous suspension of CNCs was slightly agglomerated; thus, the zeta (ζ) potential of the CNCs’ suspension was −23.72 ± 1.7 mV, and the powder had high hydrophilicity. This research will be valuable to individuals who want to explore the possibility for CNCs made of jujube cores.

Preparation and characterization of cellulose nanocrystals from spent edible fungus substrate

BACKGROUND

Spent edible fungus substrates were identified as potential sources to produce cellulose derivatives, namely purified cellulose and dicarboxyl cellulose nanocrystal (DCNC). Purified celluloses were obtained via chemical treatments and then oxidized by sequential periodate-chlorite without mechanical process. The structural properties of the DCNCs were characterized by transmission electron microscopy (TEM), Fourier-transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD) and thermal gravimetric analysis (TGA).

RESULTS

XRD results showed that the cellulose I structure was maintained, however, the crystallinity index decreased after oxidation process. The initial pyrolysis temperature of DCNCs ranged from 242 to 344 °C. TEM results revealed that DCNC was rod-shaped with an average length and width of 130.88 nm and 7.3 nm, respectively. The average specific surface area (SSA) was 366.67 m²  g^-1 . The carboxyl content was around 3.485 mmol g^-1 . Finally, the adsorption capacity for contaminations was 76.98, 126.22, 64.44 and 9.63 mg g^-1 for copper ion (Cu²⁺ ), lead ion (Pb²⁺ ), chromium (Cr³⁺ ) and amoxicillin (AMX), respectively.

CONCLUSION

This work showed a sequentially chemical oxidation for preparing nanocellulose from secondary agricultural waste with many functional applications. © 2021 Society of Chemical Industry.

Extraction of Nanocellulose for Eco-Friendly Biocomposite Adsorbent for Wastewater Treatment

In the present study, nanocellulose was extracted from palm leaves to synthesize nanocellulose/chitosan nanocomposites for the removal of dyes from textile industrial wastewater. Nanocellulose is of interest in water purification technologies because of its high surface area and versatile surface chemistry. Following bleach, alkali, and acid treatments on palm leaves, nanocellulose is obtained as a white powder. The produced nanocellulose was investigated. The adsorption capacity of chitosan, nanocellulose, and novel synthetic nanocellulose/chitosan microbeads (CCMB) for direct blue 78 dye (DB78) removal was studied. A series of batch experiments were conducted in terms of adsorbent concentration, mixing time, pH, dye initial concentration, and nanocellulose concentration in synthetic microbeads. The CCMB was characterized by using physicochemical analysis, namely Brunauer–Emmett–Teller (BET), scanning electron microscope (SEM), zeta potential analysis, and Fourier-transform infrared spectroscopy (FTIR). It was found that the surface area of synthetic CCMB is 10.4 m²/g, with a positive net surface charge. The adsorption tests showed that the dye removal efficiency increases with an increasing adsorbent concentration. The maximum removal efficiencies were 91.5% and 88.4%, using 14 and 9 g/L of CCMB-0.25:1. The initial dye concentrations were 50 and 100 mg/L under acidic conditions (pH = 3.5) and an optimal mixing time of 120 min. The equilibrium studies for CCMB-0.25:1 showed that the equilibrium data were best fitted to Langmuir isothermal model with R² = 0.99. These results revealed that nanocellulose/chitosan microbeads are an effective eco-adsorbent for the removal of direct blue 78 dye and provide a new platform for dye removal.

Extraction and Characterization of Cellulose from Agricultural By-Products of Chiang Rai Province, Thailand

Cellulose is an abundant component of the plant biomass in agricultural waste valorization that may be exploited to mitigate the excessive use of synthetic non-biodegradable materials. This work aimed to investigate the cellulose utilized by alkaline extraction with a prior bleaching process from rice straw, corncob, Phulae pineapple leaves, and Phulae pineapple peels. The bleaching and alkaline extraction process was performed using 1.4% acidified sodium chlorite (NaClO2) and 5% potassium hydroxide (KOH) in all the samples. All the samples, without and with the alkaline process, were characterized for their physico-chemical, microstructure, thermal properties and compared to commercial cellulose (COM-C). The extraction yield was the highest in alkaline-extracted cellulose from the corncob (AE-CCC) sample (p < 0.05), compared to the other alkaline-treated samples. The undesired components, including mineral, lignin, and hemicellulose, were lowest in the AE-CCC sample (p < 0.05), compared to raw and alkaline-treated samples. The microstructure displayed the flaky AE-CCC structure that showed a similar visibility in terms of morphology with that of the alkaline-treated pineapple peel cellulose (AE-PPC) and COM-C samples compared to other alkaline-treated samples with a fibrous structure. Fourier Transform Infrared (FTIR) and X-ray Diffraction (XRD) of AE-CCC samples showed the lowest amorphous regions, possibly due to the elimination of hemicellulose and lignin during bleaching and alkaline treatment. The highest crystallinity index obtained in the AE-CCC sample showed a close resemblance with the COM-C sample. Additionally, the AE-CCC sample showed the highest thermal stability, as evidenced by its higher Tonset (334.64 °C), and Tmax (364.67 °C) compared to the COM-C and alkaline-treated samples. Therefore, agricultural wastes after harvesting in the Chiang Rai province of Thailand may be subjected to an alkaline process with a prior bleaching process to yield a higher cellulose content that is free of impurities. Thus, the extracted cellulose could be used as an efficient, eco-friendly, and biodegradable material for packaging applications.

Production of Nanocellulose Film from Abaca Fibers

Abaca fibers were subjected to a TEMPO mediated oxidation to extract nanocellulose on a 500 L capacity locally fabricated reactor. A yield of 46.7% white gel material with 2.23% solid content was obtained from an overnight reaction. Transmission electron microscopy scan of the white gel material confirms the production of relatively short highly individualized cellulose nanofibril (CNF) as the diameter of abaca fiber was reduced from 16.28 μm to 3.12 nm with fiber length in the range of 100 nm to 200 nm. Nanocellulose film was prepared using air drying (CNF-VC) and vacuum oven drying (CNF-OD). The effect of CNF concentration on the physical, morphological, thermal and mechanical properties were evaluated. FTIR spectra showed cellulose I spectra between abaca fiber with both the CNF-VC film and CNF-OD film with two distinct peaks at 1620 cm−1 and 1720 cm−1 attributed to the carboxyl group resulting from the TEMPO oxidation. In addition, the carboxyl group decreases in thermal stability of cellulose. Moreover, the XRD scan showed a decrease in crystallinity index of CNF films compared to abaca fibers. CNF-VC film showed the highest tensile strength at 0.4% concentration with 88.30 MPa, while a 89.72 MPa was observed for CNF-OD film at 0.8% concentration.

Integrated pretreatment of banana agrowastes: Structural characterization and enhancement of enzymatic hydrolysis of cellulose obtained from banana peduncle

An integrated treatment coupling alkali, steam explosion and ammonia/chlorine-free bleaching with sequential mild acid pretreatment were performed to isolate and characterize cellulose from banana agrowastes followed by optimized enzymatic hydrolysis to glucose. The cellulose yield, compositional, microstructural, and morphological analysis initially obtained from three post-harvest banana agrowastes (peel, pseudostem, and peduncle) were surveyed. Isolation parameters for banana peduncle agrowastes, the most efficient precursor, were reconfigured for acid hydrolysis by applying an orthogonal L₉ array of Taguchi design. Effects of solution-to-pulp ratio, acid concentration, temperature, and reaction time on physicochemical parameters were assessed resulting in ~81% cellulose recovery. Subsequently, cellulase driven enzymatic conversion to glucose was modelled using response surface methodology (RSM), where the mutual influences of incubation time, enzyme concentration, substrate concentration, and surfactant concentration were investigated. Artificial Neural Network (ANN) modelling further improved upon RSM optimizations ensuing ~97% optimized glucose yield, verified experimentally.

Chemical Modification of Cellulose Using a Green Route by Reactive Extrusion with Citric and Succinic Acids

Cellulose is a natural, unbranched, and fibrous homopolymer that is a major component in several agroindustrial residues. The aim of this study was to extract cellulose from oat hulls and then to modify it using a green route to obtain esterified cellulose through reaction with organic acids employing the reactive extrusion process, which is a process that presents some advantages, including low effluent generation, short reaction times, and it is scalable for large scale use. Citric (CA) and succinic (SA) acids were employed as esterifying agents in different concentrations (0, 5, 12.5, and 20%). Modified cellulose samples were characterized by their degree of substitution (DS), Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (DRX), scanning electron microscopy (SEM), wettability, oil and water absorption capacities, and thermal stability. DS of modified samples ranged from 2.28 to 3.00, and FTIR results showed that the esterification occurred in all samples for both acids by observation of important bands at 1720 and 1737 cm−1 for samples modified with CA and SA, respectively. All modified samples presented increased hydrophobicity. The modification did not have an influence on the morphological structure or crystallinity pattern of all samples. This study proved to be possible to modify cellulose using a simple and ecofriendly process based on reactive extrusion with organic acids.

Chlorine-free extraction and structural characterization of cellulose nanofibers from waste husk of millet (Pennisetum glaucum)

This study aims to extract cellulose nanofibers (CNFs) from a sustainable source, millet husk, which is considered as an agro-waste worthy of consideration. Pre-treatments such as mercerisation, steam explosion, and peroxide bleaching (chlorine-free) were applied for the removal of non-cellulosic components. The bleached millet husk pulp was subjected to acid hydrolysis (5% oxalic acid) followed by homogenization to extract CNFs. The extracted CNFs were characterized using Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), Dynamic Light Scattering (DLS), Energy Dispersive X-ray Spectroscopy (EDX), Thermogravimetry (TG and DTG), Differential scanning calorimetry (DSC), and Solid state ¹³C nuclear magnetic resonance spectroscopy (solid state ¹³C NMR). The isolated CNFs show a typical cellulose type-I structure with a diameter of 10-12 nm and a crystallinity index of 58.5%. The appearance of the specific peak at 89.31 ppm in the solid state ¹³C NMR spectra validates the existence of the type-I cellulose phase in the prepared CNFs. The prepared CNFs had a maximum degradation temperature (T_max) of 341 °C, that was 31 °C greater than raw millet husk (RMH). The outcome of the study implies that the nanofibers are prominent alternatives for synthetic fibers for assorted potential applications, especially in manufacturing green composites.