Cellulose nanocrystals as templates for cetyltrimethylammonium bromide mediated synthesis of Ag nanoparticles and their novel use in PLA films

Biocompatible and antibacterial poly(lactic acid)/cellulose nanofiber‑silver nanoparticle biocomposites prepared via Pickering emulsion method

Developing biocompatible and antibacterial materials with biodegradable polymers is an ideal strategy to improve public health problems and plastic pollution simultaneously. In the present study, novel biocompatible and antibacterial poly (L-lactic acid) (PLLA, coded as P)/TEMPO-oxidized cellulose nanofiber (TOCNF, coded as T)‑silver nanoparticle (AgNP, coded as A) films were first developed. The core/shell PT Pickering emulsion was prepared by sonication treatment. The TOCNF shells with -COO-Na+ groups (∼1.5 mmol/g cellulose) were used as the support to in situ synthesize and immobilize AgNPs on the PT emulsion droplets. Silver nitrate (AgNO3) (1.5, 3.0, 4.5, and 6.0 mmol/g cellulose) was added to the PT emulsions. Then, ion-exchange reaction and hydrothermal reduction were conducted to form PTA (PTA1-PTA4) emulsions. After centrifugation to remove the excess Ag+, filtration, oven-drying, and hot-pressing, the PTA composite films were successfully prepared. The PTA3 film contained AgNPs 12.4 ± 2.8 nm in diameter and exhibited the highest antibacterial activities against the E. coli (85.2%) and S. aureus (80.1%) at 37 °C, where the initial bacterial suspension concentrations were approximately 2 × 108 CFU mL-1. Therefore, the biocompatible and antibacterial PTA3 film is a promising candidate for biomedical applications, in particular as an antibacterial bioactive packaging material.

Migration kinetic of silver from polylactic acid nanocomposite film into acidic food simulant after different high-pressure food processing

The migration study of nano-Ag migration from polylactic acid (PLA) films was studied. Samples treated by high-pressure food processing (0, 100, 200, 300, and 400 MPa pressure) were soaked in acetic acid solution and incubated at 20 °C for 90 days. At the end of storage, nano-Ag particles (AgNPs) migration from the PLA/AgNPs composite film treated under 200 MPa high pressure was the lowest. However, AgNPs migration was accelerated under 400 MPa high pressure. High-pressure processing (200 MPa) could cause denser structure and higher crystallinity degree in films than other treatments. Lower amount of AgNPs induced a decline in the intensity of specific characteristic peaks. The diffraction peak intensity of α-crystal for the film sample treated with 400 MPa was the lowest on day 60. The crystallization index of the PLA matrix changed with different high-pressure processing. The result indicated that appropriate high-pressure food processing could effectively suppress AgNPs migration from PLA-based film while contacting with acidic acid food simulant. PRACTICAL APPLICATION: The release of nanoparticles from food packaging material is a very important matter when the migration is concerned with regulatory and toxicity issues. The study described the migration kinetic of AgNPs from PLA nanocomposite film into acidic food simulant after different high-pressure food processing. The results indicated that the PLA/AgNPs nanocomposite film was safe for acidic food after high-pressure treatment.

Acrylic Functionalization of Cellulose Nanocrystals with 2-Isocyanatoethyl Methacrylate and Formation of Composites with Poly(methyl methacrylate)

Cellulose nanocrystals (CNCs) derived from renewable plant-based materials exhibit strong potential for improving properties of polymers by their dispersal in the polymer matrix as a composite phase. However, the hydrophilicity and low thermal stability of CNCs lead to compromised particle dispersibility in common polymers and limit the processing conditions of polymer-CNC composites, respectively. One route that has been explored is the modification of CNCs to alter surface chemistry. Acrylic materials are used in a broad class of polymers and copolymers with wide commercial applications. Yet, the available methods for adding groups that react with acrylics to enhance dispersion are quite limited. In this work, a versatile chemical modification route is described that introduces acryloyl functional groups on CNCs that can in turn be polymerized in subsequent steps to create acrylic-CNC composites. The hydroxyl group on CNC surfaces was reacted with the isocyanate moiety on 2-isocyanatoethyl methacrylate (IEM), a bifunctional molecule possessing both the isocyanate group and acryloyl group. The resulting modified CNCs (mCNCs) showed enhanced hydrophobicity and dispersibility in organic solvent relative to unmodified CNCs. Fourier transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy, solid-state 13C nuclear magnetic resonance (NMR) spectroscopy, and elemental analysis verified the surface modification and allowed an estimation of the degree of modification as high as 0.4 (26.7% surface hydroxyl substitution CNC). The modified CNCs were copolymerized with methyl methacrylate, and the composites had improved dispersion relative to composites with unmodified CNCs and enhanced (104%) tensile strength at 2 wt % CNC when compared to the neat poly(methyl methacrylate) (PMMA), indicating a benefit of the reactive acryloyl groups added to the CNC surface. Overall, the modification strategy was successful in functionalizing CNCs, opening possibilities for their use in organic media and matrices.

Palladium nanoparticles anchored on amphiphilic Janus-type cellulose nanocrystals for Pickering interfacial catalysis

Developing green and sustainable Pickering interfacial catalysts for organic reactions in water is of great importance to both the environment and human health. In this study, Janus-type amphiphilic cellulose nanocrystals (CNCs) were synthesized by the surface modification of hydrophilic CNCs with hydrophobic alkyl chains for efficient Pickering emulsion stabilization. Further deposition of palladium nanoparticles on amphiphilic CNCs provides catalytic activity for organic reactions in water, which occur at the interface of water and the organic reactant phase. Different reactions, hydrogenation and C-C coupling, were performed using the obtained Pickering interfacial catalyst. Excellent results were achieved in both reactions. The catalyst developed in our study is expected to advance the field of environment-friendly catalyst systems for green chemistry.

Preclinical Study of a Multi-Layered Antimicrobial Patch Based on Thin Nanocomposite Amorphous Diamond Like Carbon Films with Embedded Silver Nanoparticles

A growing number of severe infections are related to antibiotic-resistant bacteria, therefore, in recent years, alternative antimicrobial materials based on silver nanoparticles (NPs) attracted a lot of attention. In the current research, we present a medical patch prototype containing diamond-like carbon nanocomposite thin films doped with silver nanoparticles (DLC:Ag), as a source of silver ions, and an aqueous mass of the gelatin/agar mixture as a silver ion accumulation layer. The DLC:Ag thin films with 3.4 at.% of silver were deposited on synthetic silk employing reactive unbalanced DC magnetron sputtering of the silver target with argon ions performed in the acetylene gas atmosphere. The average size of the silver nanoparticles as defined by scanning electron microscope was 24 nm. After the film deposition, the samples were etched with RF oxygen plasma, aiming at efficient silver ion release in aqueous media from the nanocomposite film. In the patch prototype, a mixture of agar and gelatin was applied in silicone carrier with cavities, acting as a silver ion accumulation layer that further enhanced the antimicrobial efficiency. It was found that the DLC:Ag thin film on the silk after soaking in water for 24 h was able to release up to 4 ppm of Ag. The microbiological experiments using S. aureus bacteria were performed with the patch prototype and the silver ion saturated water, demonstrated the inactivation of 99% and 79% of bacteria, respectively. Scanning electron microscopy analysis showed that silver NPs destroyed the bacteria cell and the bacteria affected by Ag ions had spots and perforated cell wall areas with cytoplasm leakage out was obtained. A preliminary preclinical study using the laboratory animals demonstrated that using the patch prototype, the methicillin-resistant S. aureus (MRSA)-infected wound on skin surface healed faster compared with control and was able to kill all MRSA bacteria strains in the wound's bed after 72 h of treatment.

Polyurethane-Based Composites: Effects of Antibacterial Fillers on the Physical-Mechanical Behavior of Thermoplastic Polyurethanes

The challenge to manufacture medical devices with specific antibacterial functions, and the growing demand for systems able to limit bacterial resistance growth, necessitates the development of new technologies which can be easily produced at an industrial level. The object of this work was the study and the development of silver, titanium dioxide, and chitosan composites for the realization and/or implementation of biomedical devices. Thermoplastic elastomeric polyurethane was selected and used as matrix for the various antibacterial functions introduced during the processing phase (melt compounding). This strategy was employed to directly incorporate antimicrobial agents into the main constituent material of the devices themselves. With the exception of the composite filled with titanium dioxide, all of the other tested composites were shown to possess satisfactory mechanical properties. The best antibacterial effects were obtained with all the composites against Staphylococcus aureus: viability was efficiently inhibited by the prepared materials in four different bacterial culture concentrations.

Cellulose Nanocrystal Surface Cationization: A New Fungicide with High Activity against Phycomycetes capsici

At present, the management of Phytophthora capsici (P. capsici) mainly relies on chemical pesticides. However, along with the resistance generated by P. capsici to these chemical pesticides, the toxicity and non-degradability of this chemical molecule may also cause serious environmental problems. Herein, a new bio-based nano-antifungal material (CNC@CTAB) was made with coating hexadecyl trimethyl ammonium bromide (CTAB) on the surface of a cellulose nanocrystal (CNC). This material was then applied to the prevention of P. capcisi. This particle was facilely fabricated by mixing CTAB and sulfuric group modified CNC in an aqueous solvent. Compared to pure CTAB, the enrichment of CTAB on the CNC surface showed a better anti-oomycete activity both in vitro and in vivo. When CNC@CTAB was applied on P. capsici in vitro, the inhibition rate reached as high as 100%, while on the pepper leaf, the particle could also efficiently prevent the infection of P. capsici, and achieve a disease index as low as zero Thus, considering the high safety of CNC@CTAB in agricultural applications, and its high anti-oomycete activity against P. capsici, we believe that this CNC@CTAB has great application potential as a new green nano-fungicide in P. capsici management during the production of peppers or other vegetables.

A review on versatile applications of blends and composites of CNC with natural and synthetic polymers with mathematical modeling

Cellulose is world's most abundant, renewable and recyclable polysaccharide on earth. Cellulose is composed of both amorphous and crystalline regions. Cellulose nanocrystals (CNCs) are extracted from crystalline region of cellulose. The most attractive feature of CNC is that it can be used as nanofiller to reinforce several synthetic and natural polymers. In this article, a comprehensive overview of modification of several natural and synthetic polymers using CNCs as reinforcer in respective polymer matrix is given. The immense activities of CNCs are successfully utilized to enhance the mechanical properties and to broaden the field of application of respective polymer. All the technical scientific issues have been discussed highlighting the recent advancement in biomedical and packaging field.

Cellulose nanowhiskers decorated with silver nanoparticles as an additive to antibacterial polymers membranes fabricated by electrospinning

Antimicrobial films based on distinct polymer matrices, poly (vinyl alcohol) (PVA) or poly (N-isopropylacrylamide) (PNIPAAm), and silver nanoparticles (AgNPs) immobilized onto cellulose nanowhiskers (CWs) were successfully prepared by either casting or electrospinning. CWs were first functionalized with carboxylate groups (labeled as CWSAc) and later they were immersed in a silver nitrate solution (AgNO₃). After Ag⁺ ions anchored in the COO^- groups are chemically reduced to produce AgNPs. The CWSAc/AgNPs biological activity was evaluated against Staphylococcus aureus (S. aureus), Bacillus Subtilis (B. subtilis), Escherichia coli (E. coli), and Candida albicans (C. albicans). The materials were more effective against C. albicans that showed a MIC of 15.6 µg/mL. In the process of AgNPs synthesis, the activity of the stabilizing agent (gelatin) and concentration of precursor and reducing agents were evaluated. The synthesized polymeric films displayed good antimicrobial activity against S. aureus, E. coli, and Pseudomonas aeruginosa (P. aeruginosa) bacteria. The PVA films with CWSAc/AgNPs showed diameter of the inhibition halo of up to 11 mm. The results obtained displayed that the films obtained have a potential application to be used in different fields such as packaging, membrane filtration, wound dressing, clothing and in different biomedical applications.

A facile template approach to preparing stable NFC/Ag/polyaniline nanocomposites for imparting multifunctionality to paper

Nanocomposites of function polymer and inorganic nanoparticles have many beneficial properties and can be used in many applications. However, the formation of aggregates of the polymer and inorganic nanoparticles in the nanocomposites limits their use in practical applications. Here, a facile approach to preparing stable nanofibrillated cellulose (NFC)/Ag/polyaniline nanocomposites by the templates of NFC was developed. The Ag nanoparticles and polyaniline were loaded on the NFC by the reduction of Ag cations and in situ chemical polymerization in the templates of NFC. The network structure of the NFC and the electrostatic repulsion resulted in the formation of stable nanocomposites. Owing to the well-dispersed Ag nanoparticles and polyaniline in the nanocomposites, the nanocomposites can be coated on the paper uniformly, thus imparting excellent conductivity and antibacterial properties to paper. The coated paper can be used as a new type of conductive paper with excellent antibacterial activity.