Review of chitosan composite as a heavy metal adsorbent: Material preparation and properties

A novel chitosan/cellulose phosphonate composite hydrogel for ultrafast and efficient removal of Pb(II) and Cu(II) from wastewater

Developing green and high-performance adsorbents to separate heavy metals from wastewater is a challenging task. Biomass hydrogel has the advantages of low cost, renewability, and biodegradability, but it has the problem of low adsorption efficiency. Herein, a novel chitosan/cellulose phosphonate composite hydrogel(CS/MCCP) is fabricated by two steps of reactions including the Phosphorylation reaction and the Mannich reaction. As an excellent chelating group, the phosphonate group greatly enhances the adsorption efficiency of the biomass hydrogel. The CS/MCCP shows ultrafast adsorption rate and excellent adsorption capacity for Pb(II) and Cu(II). The saturated adsorption capacity of Pb(II) and Cu(II) is 211.42 and 74.29 mg·g-1, respectively. The adsorption equilibration time is only 10 min. The adsorption performance of the CS/MCCP is superior to that of the reported cellulose/chitosan hydrogels. Besides, an in-depth analysis of the adsorption mechanism is conducted using X-ray photoelectron spectroscopy(XPS) combined with Density Functional Theory(DFT) calculation. The results reveal that the adsorption mechanism is electrostatic attraction and surface complexation, and there is a synergistic coordination between the phosphonate groups and the amino groups.

Effect of biopolymer chitosan on manganese immobilization improvement by microbial‑induced carbonate precipitation

Microbially induced carbonate precipitation (MICP), as an eco-friendly and promising technology that can transform free metal ions into stable precipitation, has been extensively used in remediation of heavy metal contamination. However, its depressed efficiency of heavy metal elimination remains in question due to the inhibition effect of heavy metal toxicity on bacterial activity. In this work, an efficient, low-cost manganese (Mn) elimination strategy by coupling MICP with chitosan biopolymer as an additive with reduced treatment time was suggested, optimized, and implemented. The influences of chitosan at different concentrations (0.01, 0.05, 0.10, 0.15 and 0.30 %, w/v) on bacterial growth, enzyme activity, Mn removal efficiency and microstructure properties of the resulting precipitation were investigated. Results showed that Mn content was reduced by 94.5 % within 12 h with 0.15 % chitosan addition through adsorption and biomineralization as MnCO3 (at an initial Mn concentration of 3 mM), demonstrating a two-thirds decrease in remediation time compared to the chitosan-absent system, whereas maximum urease activity increased by ∼50 %. Microstructure analyses indicated that the mineralized precipitates were spherical-shaped MnCO3, and a smaller size and more uniform distribution of MnCO3 is obtained by the regulation of abundant amino and hydroxyl groups in chitosan. These results demonstrate that chitosan accelerates nucleation and tunes the growth of MnCO3 by providing nucleation sites for mineral formation and alleviating the toxicity of metal ions, which has the potential to upgrade MICP process in a sustainable and effective manner. This work provides a reference for further understanding of the biomineralization regulation mechanism, and gives a new perspective into the application of biopolymer-intensified strategies of MICP technology in heavy metal contamination.

Unveiling the potential of biomaterials and their synergistic fusion in tissue engineering

Inspired by nature, tissue engineering aims to employ intricate mechanisms for advanced clinical interventions, unlocking inherent biological potential and propelling medical breakthroughs. Therefore, medical, and pharmaceutical fields are growing interest in tissue and organ replacement, repair, and regeneration by this technology. Three primary mechanisms are currently used in tissue engineering: transplantation of cells (I), injection of growth factors (II) and cellular seeding in scaffolds (III). However, to develop scaffolds presenting highest potential, reinforcement with polymeric materials is growing interest. For instance, natural and synthetic polymers can be used. Regardless, chitosan and keratin are two biopolymers presenting great biocompatibility, biodegradability and non-antigenic properties for tissue engineering purposes offering restoration and revitalization. Therefore, combination of chitosan and keratin has been studied and results exhibit highly porous scaffolds providing optimal environment for tissue cultivation. This review aims to give an historical as well as current overview of tissue engineering, presenting mechanisms used and polymers involved in the field.

Anisotropic materials based on carbohydrate polymers: A review of fabrication strategies, properties, and applications

Anisotropic structures exist in almost all living organisms to endow them with superior properties and physiological functionalities. However, conventional artificial materials possess unordered isotropic structures, resulting in limited functions and applications. The development of anisotropic structures on carbohydrates is reported to have an impact on their properties and applications. In this review, various alignment strategies for carbohydrates (i.e., cellulose, chitin and alginate) from bottom-up to top-down strategies are discussed, including the rapidly developed innovative technologies such as shear-induced orientation through extrusion-based 3D/4D printing, magnetic-assisted alignment, and electric-induced alignment. The unique properties and wide applications of anisotropic carbohydrate materials across different fields, from biomedical, biosensors, smart actuators, soft conductive materials, to thermal management are also summarized. Finally, recommendations on the selection of fabrication strategies are given. The major challenge lies in the construction of long-range hierarchical alignment with high orientation degree and precise control over complicated architectures. With the future development of hierarchical alignment strategies, alignment control techniques, and alignment mechanism elucidation, the potential of anisotropic carbohydrate materials for scalable manufacture and clinical applications will be fully realized.

Chitosan-Based Beads Incorporating Inorganic-Organic Composites for Copper Ion Retention in Aqueous Solutions

In recent years, there has been a challenging interest in developing low-cost biopolymeric materials for wastewater treatment. In the present work, new adsorbents, based on different types of chitosan (commercial, commercial chitin-derived chitosan and chitosan synthesized from shrimp shell waste) and inorganic-organic composites have been evaluated for copper ions removal. The efficacy of the synthesis of chitosan-based composite beads has been determined by studying various characteristics using several techniques, including FTIR spectroscopy, X-ray diffraction, porosimetry (N2 adsorption), and scanning electron microscopy (SEM). Adsorption kinetics was performed using different adsorption models to determine the adsorption behavior of the materials in the aqueous media. For all composite beads, regardless of the type of chitosan used, good capacity to remove copper ions from simulated waters was observed (up to 17 mg/g), which proves that the new materials hold potential for heavy metal retention. However, the adsorption efficiency was influenced by the type of chitosan used. Thus, for the series where commercial chitosan (CC) was used, the removal efficiency was approximately 29%; for the series with chitosan obtained from commercial chitin (SC), the removal efficiency was approximately 34%; for the series with chitosan enriched with CaCO3 (SH), the removal efficiency was approximately 52%.

Effects of Dietary Supplementation with Chitosan on the Muscle Composition, Digestion, Lipid Metabolism, and Stress Resistance of Juvenile Tilapia (Oreochromis niloticus) Exposed to Cadmium-Induced Stress

The aim of this study was to investigate the effects of dietary chitosan supplementation on the muscle composition, digestion, lipid metabolism, and stress resistance, and their related gene expression, of juvenile tilapia (Oreochromis niloticus) subjected to cadmium (Cd2+) stress. Juvenile tilapia with an initial body weight of 21.21 ± 0.24 g were fed with a formulated feed containing five different levels (0%, 0.5%, 1.0%, 1.5%, and 2.0%) of chitosan for 60 days, while the water in all experimental groups contained a Cd2+ concentration of 0.2 mg/L. The results showed that, compared with the control group (0% chitosan), the contents of crude fat and crude protein in the muscle, the activities of lipase, trypsin, and amylase in the intestine, as well as the relative expression levels of metallothionein (mt), cytochrome P450 1A (cyp1a), carnitine palmitoyltransferase-1 (cpt-1), peroxisome proliferator-activated receptor alpha (pparα), peroxisome proliferator-activated receptor gamma (pparγ), hormone-sensitive lipase (hsl), lipoprotein lipase (lpl), malate dehydrogenase (mdh), leptin (lep), fatty acid synthase (fas), sterol regulatory element-binding protein 1 (srebp1), and stearoyl-CoA desaturase (scd) genes in the liver of juveniles were significantly increased (p < 0.05). In conclusion, dietary chitosan supplementation could alleviate the effects of Cd2+ stress on the muscle composition, digestive enzymes, lipid metabolism, and stress resistance, and their related gene expression, of juvenile tilapia, and to some extent reduce the toxic effect of Cd2+ stress on tilapia.

N-lauric-O-carboxymethyl chitosan: Synthesis, characterization and application as a pH-responsive carrier for curcumin particles

A pH-responsive amphiphilic chitosan derivative, N-lauric-O-carboxymethyl chitosan (LA-CMCh), is synthesized. Its molecular structures are characterized by FTIR, 1H NMR, and XRD methods. The influencing factors are investigated, including the amount of lauric acid (LA), carboxymethyl chitosan (CMCh), N-(3-dimethylaminopropyl)-N'-ethylcarbodiimide hydrochloride (EDC), and N-hydroxysuccinimide (NHS), and their molar ratio, reaction time, and reaction temperature on the substitution. The degrees of substitution (DS) of the lauric groups on the -NH2 groups are calculated based on the integrated data of 1H NMR spectra. The optimum reaction condition is obtained as a reaction time of 6 h, a reaction temperature of 80 °C, and a molar ratio of lauric acid to O-carboxymethyl chitosan to N-(3-dimethylaminopropyl)-N'-ethylcarbodiimide hydrochloride to N-hydroxysuccinimide of 1:3:4.5:4.5, respectively. The crystallinity and initial decomposition temperature of LA-CMCh decrease, but the maximum decomposition temperature increases. The crystallinity is reduced due to the introduction of LA and the degree of hydrogen bonding among LA-CMCh molecules. LA-CMCh could self-aggregate into particles, which size and critical aggregation concentration depend on the degree of substitution and medium pH. LA-CMCh aggregates could load curcumin up to 21.70 %, and continuously release curcumin for >200 min. LA-CMCh shows nontoxicity to fibroblast HFF-1 cells and good antibacterial activity against S. aureus and E. coli, indicating that it could be used as an oil-soluble-drug carrier.

Simultaneous Cr(VI) reduction and Cr(III) sequestration in a wide pH range by using magnetic chitosan-based biopolymer

The simultaneous reduction of Cr(VI) and sequestration of the resulting Cr(III) in one process is highly desirable as a cost-effective and environmental-friendly approach for the decontamination of Cr(VI)-polluted wastewater. However, most of the existing adsorptive materials are only effective in low pH environments (pH = 1-3), severely restricting the adsorption efficiency and cost effectiveness. Herein, we proposed a chitosan-based magnetic porous microsphere (PPy@PMCS) for simultaneous Cr(VI) reduction and Cr(III) sequestration in a wide pH range. Benefiting from its abundant interaction sites, Cr(VI) was effectively adsorbed on the surface and then immediately reduced to Cr(III) with much lower toxicity. Most importantly, the resulting Cr(III) was in-situ sequestrated by the complexation of chitosan matrix. As a result, PPy@PMCS exhibited a maximum Cr(VI) adsorption capacity of 330.42 mg/g at pH 2.0 and an adsorption capacity of 167.82 mg/g even at near neutral pH (6.0), which is superior to most reported adsorbents. Furthermore, the exhausted PPy@PMCS can be rapidly separated from solutions under an external magnetic field and facilely regenerated. The proposed novel biopolymer-based material shows great application potentials in wastewater treatment.

Efficient adsorption of organic pollutants phthalates and bisphenol A (BPA) utilizing magnetite functionalized covalent organic frameworks (MCOFs): A promising future material for industrial applications

The utilization of phthalates and bisphenol A (BPA) as the major component in plastic and its derivative industry has raised concerns among the public due to the harmful effects caused by these organic pollutants. These pollutants are found to exhibit unique physicochemical properties that allow the pollutants to have prolonged existence in the environment, thus causing damage to the environment. Since phthalates and bisphenol A are used in a variety of industrial applications, the industry must recover these compounds from its water before releasing the pollutants into the environment. As a result, these materials have a promising future in industrial applications. Therefore, the discovery of new quick and reliable abatement technologies is important to ensure that these organic pollutants can be detected and removed from the water sources. This review highlights the use of the adsorption method to remove phthalates and BPA from water sources by employing novel modified adsorbent magnetite functionalized covalent organic frameworks (MCOFs). MCOFs is a new class of porous materials that have demonstrated promising features in a variety of applications due to their adaptable structures, significant surface areas, configurable porosity, and customizable chemistry. The structural attributes, functional design strategies, and specialized for environmental applications before offering some closing thoughts and suggestions for further research were discussed in this paper in addition to developing an innovative solution for the industry to the accessibility for clean water.

Recent advances in removal of inorganic anions from water by chitosan-based composites: A comprehensive review

Chitosan is a modified natural carbohydrate polymer that has been found in the exoskeletons of crustaceans (e.g., lobsters, shrimps, krill, barnacles, crayfish, etc.), mollusks (octopus, oysters, squids, snails), algae (diatoms, brown algae, green algae), insects (silkworms, beetles, scorpions), and the cell walls of fungi (such as Ascomycetes, Basidiomycetes, and Phycomycetes; for example, Aspergillus niger and Penicillium notatum). However, it is mostly acquired from marine crustaceans such as shrimp shells. Chitosan-based composites often present superior chemical, physical, and mechanical properties compared to single chitosan by incorporating the benefits of both counterparts in the nanocomposites. The tunable surface chemistry, abundant surface-active sites, facilitation synthesize and functionalization, good recyclability, and economic viability make the chitosan-based materials potential adsorbents for effective and fast removal of a broad range of inorganic anions. This article reviews the different types of inorganic anions and their effects on the environment and human health. The development of the chitosan-based composites synthesis, the various parameters like initial concentration, pH, adsorbent dosage, temperature, the mechanism of adsorption, and regeneration of adsorbents are discussed in detail. Finally, the prospects and technical challenges are emphasized to improve the performance of chitosan-based composites in actual applications on a pilot or industrial scale.

Myrica esculenta Leaf Extract-Assisted Green Synthesis of Porous Magnetic Chitosan Composites for Fast Removal of Cd (II) from Water: Kinetics and Thermodynamics of Adsorption

Heavy metal contamination in water resources is a major issue worldwide. Metals released into the environment endanger human health, owing to their persistence and absorption into the food chain. Cadmium is a highly toxic heavy metal, which causes severe health hazards in human beings as well as in animals. To overcome the issue, current research focused on cadmium ion removal from the polluted water by using porous magnetic chitosan composite produced from Kaphal (Myrica esculenta) leaves. The synthesized composite was characterized by BET, XRD, FT-IR, FE-SEM with EDX, and VSM to understand the structural, textural, surface functional, morphological-compositional, and magnetic properties, respectively, that contributed to the adsorption of Cd. The maximum Cd adsorption capacities observed for the Fe3O4 nanoparticles (MNPs) and porous magnetic chitosan (MCS) composite were 290 mg/g and 426 mg/g, respectively. Both the adsorption processes followed second-order kinetics. Batch adsorption studies were carried out to understand the optimum conditions for the fast adsorption process. Both the adsorbents could be regenerated for up to seven cycles without appreciable loss in adsorption capacity. The porous magnetic chitosan composite showed improved adsorption compared to MNPs. The mechanism for cadmium ion adsorption by MNPs and MCS has been postulated. Magnetic-modified chitosan-based composites that exhibit high adsorption efficiency, regeneration, and easy separation from a solution have broad development prospects in various industrial sewage and wastewater treatment fields.

Physicochemical investigation of mercury sorption on mesoporous thioacetamide/chitosan from wastewater

Mercury is a toxic environmental element, so it was necessary to prepare a new, highly efficient, cheap sorbent to remove it. A mesoporous thioacetamide/chitosan (MTA/CS) was manufactured via a simplistic strategy; the chitin deacetylation to gain chitosan (CS) and the addition of thioacetamide. The as-prepared MTA/CS was characterized using X-ray diffraction, EDX, SEM, FTIR, and BET surface analysis. According to the findings, the MTA/CS was effectively synthesized. The removal behaviors of Hg2+ onto MTA/CS composite were inspected, which suggested that the MTA/CS composite exhibited great sorption properties for Hg2+ in liquid solutions. The maximal Hg2+ sorption capacity was 195 mg/g. The effects of temperature, Hg2+ concentration, contacting time, and MTA/CS concentration on sorption were analyzed. The 2nd-order model and Langmuir isotherm were suitable for the physicochemical adsorption processes. Thermodynamic analysis showed that the Hg2+ adsorption process onto the MTA/CS composite is exothermic and occurred spontaneously. The desorption condition of Hg2+ from its loaded MTA/CS was also gained. Likewise, the MTA/CS sorbent was undoubtedly regenerated by 0.8 M NaNO3 80 min contacting and 1:50 S:L ratio. The versatility and durability of MTA/CS sorbent were investigated via nine sorption-extraction cycles. The optimum parameters were applied to wastewater. Based on the result, the as-prepared MTA/CS might be a potential sorbent for removing Hg2+ from liquid solutions.

A critical review of enzymes immobilized on chitosan composites: characterization and applications

Enzymes with industrial significance are typically used in biological processes. However, instability, high sensitivity, and impractical recovery are the major drawbacks of enzymes in practical applications. In recent years, the immobilization technology has attracted wide attention to overcoming these restrictions and improving the efficiency of enzyme applications. Chitosan (CS) is a unique functional substance with biocompatibility, biodegradability, non-toxicity, and antibacterial properties. Chitosan composites are anticipated to be widely used in the near future for a variety of purposes, including as supports for enzyme immobilization, because of their advantages. Therefor this review explores the effects of the chitosan's structure, molecular weight, degree of deacetylation on the enzyme immobilized, effect of key factors, and the enzymes immobilized on chitosan based composites for numerous applications, including the fields of biosensor, biomedical science, food industry, environmental protection, and industrial production. Moreover, this study carefully investigates the advantages and disadvantages of using these composites as well as their potential in the future.

A review on heavy metal biosorption utilizing modified chitosan

Heavy metal pollution in water bodies is a global concern. The prominent source of metal contamination in aqueous streams and groundwater is wastewater containing heavy metal ions. Elevated concentrations of heavy metals in water bodies can have a negative impact on water quality and public health. The most effective way to remove metal contaminants from drinking water is thought to be adsorption. A deacetylated derivative of chitin, chitosan, has a wide range of commercial uses since it is biocompatible, nontoxic, and biodegradable. Due to its exceptional adsorption behavior toward numerous hazardous heavy metals from aqueous solutions, chitosan and its modifications have drawn a lot of interest in recent years. Due to its remarkable adsorption behavior toward a range of dangerous heavy metals, chitosan is a possible agent for eliminating metals from aqueous solutions. The review has focused on the ideas of biosorption, its kinds, architectures, and characteristics, as well as using modified (physically and chemically modified) chitosan, blends, and composites to remove heavy metals from water. The main objective of the review is to describe the most important aspects of chitosan-based adsorbents that might be beneficial for enhancing the adsorption capabilities of modified chitosan and promoting the usage of this material in the removal of heavy metal pollutants.

Chitosan cross-linked and grafted with epichlorohydrin and 2,4-dichlorobenzaldehyde as an efficient adsorbent for removal of Pb(II) ions from aqueous solution

Epichlorohydrin-modified chitosan-Schiff base composite (CS/24Cl/ECH) prepared via the one-pot reaction as characterized by Fourier transform Infra-Red spectroscopy (FT-IR), X-ray powder diffraction (XRD), Differential scanning calorimetry (DSC) and Scanning electron microscope (SEM). Its removal ability of Pb(II) ions from aqueous solution was investigated. The adsorption of Pb(II) ions carried out at different initial pH, dose of CS/24-Cl/ECH, contact time and co-existing ions. The maximum adsorption capacity of Pb(II) ions was 170 mg/g. Finally, based on the absorption results, the adsorption of Pb(II) ions was fitted by single-layer Langmuir isotherm model and the pseudo-second-order (PSO) kinetics model. The absorption mechanism of Pb(II) ions was controlled by chemical coordination Pb(II) ions with the active sites on the surface of CS/24Cl/ECH composite. Also, CS/24Cl/ECH showed excellent recyclable efficiency up to 5 cycle and potential sorbent for other heavy metal ions.

Chitosan Oligomer as a Raw Material for Obtaining Polyurethane Foams

Decreasing oil extraction stimulates attempts to use biologically available sources to produce polyols, which are the basic components for obtaining polyurethane foams. Plants are inexhaustible source of oils, sugars, starches, and cellulose. Similar substrates to obtain polyols are chitosans. Commercially available modified chitosans are soluble in water, which gives them the possibility to react with hydroxyalkylating agents. We used a water-soluble chitosan previously to obtain polyols suitable for producing rigid polyurethane foams. Here, we described hydroxyalkylation of a low-molecular-weight chitosan (oligomeric chitosan) with glycidol and ethylene carbonate to obtain polyols. The polyols were isolated and studied in detail by IR, ¹H-NMR, and MALDI-ToF methods. Their properties, such as density, viscosity, surface tension, and hydroxyl numbers, were determined. The progress of the hydroxyalkylation reaction of water-soluble chitosan and chitosan oligomer with glycidol was compared in order to characterize the reactivity and mechanism of the process. We found that the hydroxyalkylation of chitosan with glycidol in glycerol resulted in the formation of a multifunctional product suitable for further conversion to polyurethane foams with favorable properties. The straightforward hydroxyalkylation of chitosan with glycidol was accompanied by the oligomerization of glycidol. The hydroxyalkylation of chitosan with glycidol in the presence of ethylene carbonate was accompanied by minor hydroxyalkylation of chitosan with ethylene carbonate. The chosen polyols were used to obtain rigid polyurethane foams which were characterized by physical parameters such as apparent density, water uptake, dimension stability, heat conductance, compressive strength, and heat resistance at 150 and 175 °C. The properties of polyurethane foams obtained from chitosan-oligomer and water-soluble-chitosan sources were compared. Polyurethane foams obtained from polyols synthesized in the presence of glycerol had advantageous properties such as low thermal conductivity, enhanced thermal resistance, dimensional stability, low water uptake, and high compressive strength, growing remarkably upon thermal exposure.

Green composites based on volcanic red algae Cyanidiales, cellulose, and coffee waste biomass modified with magnetic nanoparticles for the removal of methylene blue

In this paper, green nanocomposites based on biomass and superparamagnetic nanoparticles were synthesized and used as adsorbents to remove methylene blue (MB) from water with magnetic separation. The adsorbents were synthesized through the wet co-precipitation technique, in which iron-oxide nanoparticles coated the cores based on coffee, cellulose, and red volcanic algae waste. The procedure resulted in materials that could be easily separated from aqueous solutions with magnets. The morphology and chemical composition of the nanocomposites were characterized by SEM, FT-IR, and XPS methods. The adsorption studies of MB removal with UV-vis spectrometry showed that the adsorption performance of the prepared materials strongly depended on their morphology and the type of the organic adsorbent. The adsorption studies presented the highest effectiveness in neutral pH with only a slight effect on ionic strength. The MB removal undergoes pseudo-second kinetics for all adsorbents. The maximal adsorption capacity for the coffee@Fe₃O₄-2, cellulose@Fe₃O₄-1, and algae@Fe₃O₄-1 is 38.23 mg g^-1, 41.61 mg g^-1, and 48.41 mg g^-1, respectively. The mechanism of MB adsorption follows the Langmuir model using coffee@Fe₃O₄ and cellulose@Fe₃O₄, while for algae@Fe₃O₄ the process fits to the Redlich-Peterson model. The removal efficiency analysis based on UV-vis adsorption spectra revealed that the adsorption effectiveness of the nanocomposites increased as follows: coffee@Fe₃O₄-2 > cellulose@Fe₃O₄-1 > algae@Fe₃O₄-1, demonstrating an MB removal efficiency of up to 90%.

Synthesis and characterization of pendant N,N-dimethylaminobenzaldehyde-functionalized chitosan Schiff base composite (CS@MABA) as a new sorbent for removal of Pb(II) ions from aqueous media

In this work, new pendant N,N-dimethylaminobenzaldehyde-functionalized chitosan Schiff base composite (CS@MABA) was prepared from the simple and convenient condensation reaction between chitosan (CS) and N,N-dimethylaminobenzaldehyde (MABA) in ethanol-glacial acetic acid (1:1 v/v) and characterized by Fourier transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD), differential scanning calorimetry (DSC) and scanning electron microscope (SEM). The as-prepared composite CS@MABA was applied for the removal of Pb(II) ions, due to the presence of imine, hydroxyl and phenyl groups, and the effects of important parameters such as solution pH, contact time and sorbent dosage on the removal percentage and adsorption capacity were investigated and discussed. The optimum conditions were found to be at pH 5, adsorbent dosage of 0.1 g, Pb(II) concentration of 50 mg/L and contact time of 60 min. The maximum Pb(II) removal percentage was found to be 94.28 % with the high adsorption capacity of 165 mg/g. The adsorption capacity of CS@MABA is remain 87 % after 5 adsorption-desorption cycles. The adsorption kinetic and isotherm studies indicated that the Pb(II) removal by CS@MABA follows a pseudo-first order and Langmuir models, respectively. Compared to similar compounds, the synthesized CS@MABA composite has shown a relatively high yield for removing Pb(II) ions. According to these results, the CS@MABA suggested for the sorption of other heavy metals.

Valorization of biowastes for clean energy production, environmental depollution and soil fertility

The mother earth is a source of natural resources that, in conjunction with anthropogenic activities, generates a wide spectrum of different biowastes. These biomaterials can be used as low-cost raw feedstock to produce bioenergy, value-added products, and other commodities. However, the improper management and disposal of these biowastes can generate relevant environmental impacts. Consequently, it is imperative to explore alternative technologies for the valorization and exploitation of these wastes to obtain benefits for the society. This review covers different aspects related to valorization of biowastes and their applications in water pollution, soil fertility and green energy generation. The classification and characteristics of different biowastes (biosolids, animal wastes and effluents, plant biomass, wood and green wastes) including their main generation sources are discussed. Different technologies (e.g., pyrolysis, hydrothermal carbonization, anaerobic digestion, gasification, biodrying) for the transformation and valorization of these residues are also analyzed. The application of biowastes in soil fertility, environmental pollution and energy production are described and illustrative examples are provided. Finally, the challenges related to implement low-cost and sustainable biowaste management strategies are highlighted. It was concluded that reliable simulation studies are required to optimize all the logistic stages of management chain of these residues considering the constraints generated from the economic, environmental and social aspects of the biowaste generation sources and their locations. The recollection and sorting of biowastes are key parameters to minimize the costs associated to their management and valorization. Also, the concepts of Industry 4.0 can contribute to achieve a successful commercial production of the value-added products obtained from the biowaste valorization. Overall, this review provides a general outlook of biowaste management and its valorization in the current context of circular economy.

Polyelectrolyte Coatings-A Viable Approach for Cultural Heritage Protection

The continuous degradation of cultural heritage artifacts (due to different factors, including the rising air pollution, climate change or excessive biological activity, among others) requires the continuous development of protection strategies, technologies and materials. In this regard, polyelectrolytes have offered effective ways to fight against degradation but also to conserve the cultural heritage objects. In this review, we highlight the key developments in the creation and use of polyelectrolytes for the preservation, consolidation and cleaning of the cultural heritage artifacts (with particular focus on stone, metal and artifacts of organic nature, such as paper, leather, wood or textile). The state of the art in this area is presented, as well as future development perspectives.

Preparation of metal organic frameworks modified chitosan composite with high capacity for Hg(II) adsorption

In this study, a novel modified chitosan composite adsorbent (UNCS) was prepared by crosslinking between chitosan and metal organic frameworks (MOFs) material UiO-66-NH₂ using epichlorohydrin as crosslinker. The influence of the prepared conditions was investigated. The structure and morphology of the composite were characterized by FT-IR, XRD, SEM, TGA, BET and zeta potential analysis. Effects of different variables for adsorption of Hg(II) on this adsorbent were explored. The kinetic studies indicated that the adsorption process followed the pseudo-second-order kinetic model and the adsorption equilibrium could be reached within 2 h. The adsorption was mainly controlled by chemical process. Adsorption isothermal studies illustrated that the adsorption fitted Langmuir isotherm model, implying the homogeneous adsorption on the surface of the adsorbent. The adsorbent exhibited high uptake and the maximum capacity from Langmuir model could reach 896.8 mg g^-1 at pH 6. Thermodynamic studies showed the spontaneous nature and exothermic nature of the adsorption process. Additionally, the removal of Hg(II) on UNCS could achieve over 90 %. The adsorption-desorption cycled experiments indicated the appropriate reusability of the adsorbent. Hence, this adsorbent would be promising for the removal of Hg(II) from wastewater.

Preparation of Amphiphilic Chitosan-Loaded Bentonite Adsorbent and Its Performance in Removing Organic Matter from Coking Wastewater

An amphiphilic chitosan-loaded bentonite adsorbent (C18CTS-BT) was prepared for the efficient removal of organic matter from coking wastewater. The structure and surface morphology of adsorbents were characterized by FT-IR, XRD, and SEM. The removal of those organics by C18CTS-BT was investigated by comparing the adsorption performances of C18CTS-BT with bentonite (BT) and chitosan-loaded bentonite (CTS-BT). The results showed that compared with BT and CTS-BT, C18CTS-BT showed the performance advantages of having a low dosage, wide pH range, and short adsorption equilibrium time. The optimized treatment process was as follows: the adsorbent dosage was 1.5 g·L^-1, the adsorption time was 60 min, and the pH of the system was 7.0. The chemical oxygen demand (COD) of the coking wastewater treated with BT, CTS-BT, and C18CTS-BT decreased from 342 mg·L^-1 in the raw water to 264 mg·L^-1, 218 mg·L^-1, and 146 mg·L^-1, corresponding to COD removal rates of 22.81%, 36.26%, and 57.31%, respectively. The results of GC-MS analysis also confirmed that C18CTS-BT could remove most of the organic compounds in coking wastewater, especially long-chain alkanes and their derivatives. The hydrophobic modification of the adsorbent material can effectively improve the removal performance of organic compounds from coking wastewater.

Polyols and Polyurethane Foams Based on Water-Soluble Chitosan

At present, majority of polyols used in the synthesis of polyurethane foams are of petrochemical origin. The decreasing availability of crude oil imposes the necessity to convert other naturally existing resources, such as plant oils, carbohydrates, starch, or cellulose, as substrates for polyols. Within these natural resources, chitosan is a promising candidate. In this paper, we have attempted to use biopolymeric chitosan to obtain polyols and rigid polyurethane foams. Four methods of polyol synthesis from water-soluble chitosan functionalized by reactions of hydroxyalkylation with glycidol and ethylene carbonate with variable environment were elaborated. The chitosan-derived polyols can be obtained in water in the presence of glycerol or in no-solvent conditions. The products were characterized by IR, 1H-NMR, and MALDI-TOF methods. Their properties, such as density, viscosity, surface tension, and hydroxyl numbers, were determined. Polyurethane foams were obtained from hydroxyalkylated chitosan. The foaming of hydroxyalkylated chitosan with 4,4′-diphenylmethane diisocyanate, water, and triethylamine as catalysts was optimized. The four types of foams obtained were characterized by physical parameters such as apparent density, water uptake, dimension stability, thermal conductivity coefficient, compressive strength, and heat resistance at 150 and 175 °C. It has been found that the obtained materials had most of the properties similar to those of classic rigid polyurethane foams, except for an increased thermal resistance up to 175 °C. The chitosan-based polyols and polyurethane foams obtained from them are biodegradable: the polyol is completely biodegraded, while the PUF obtained thereof is 52% biodegradable within 28 days in the soil biodegradation oxygen demand test.

Recent Application Prospects of Chitosan Based Composites for the Metal Contaminants Wastewater Treatment

Heavy metals, known for their toxic nature and ability to accumulate and magnify in the food chain, are a major environmental concern. The use of environmentally friendly adsorbents, such as chitosan (CS)—a biodegradable cationic polysaccharide, has gained attention for removing heavy metals from water. This review discusses the physicochemical properties of CS and its composites and nanocomposites and their potential application in wastewater treatment.

Adsorption and Removal of Cr6+, Cu2+, Pb2+, and Zn2+ from Aqueous Solution by Magnetic Nano-Chitosan

Magnetic nano-chitosan (MNC) was prepared and characterized. The kinetics, thermodynamics, and influencing factors of the adsorption of Cr6+, Cu2+, Pb2+, and Zn2+, as well as their competitive adsorption onto MNC in aqueous solution, were studied. The results showed that the adsorption kinetics and thermodynamics of Cr6+, Cu2+, Pb2+, and Zn2+ were well described by the pseudo-second-order kinetic model and Langmuir isothermal adsorption model, indicating that the adsorption was mainly chemical adsorption and endothermic. Increasing the dosage of MNC, the equilibrium adsorption capacity (qe) of Cr6+, Cu2+, Pb2+, and Zn2+ decreased; their removal rate (η) increased. With the increase in the solution’s pH, the qe and η of Cr6+ first increased and then decreased; the qe and η of Cu2+, Pb2+, and Zn2+ increased. With the increase in the metal ion initial concentration, the qe increased; the η of Cr6+, Cu2+, and Zn2+ decreased, while the η of Pb2+ increased first and then decreased. Temperature had a weak influence on the qe of Cr6+ and Pb2+, while it had a strong influence on Cu2+ and Zn2+, the qe and η were greater when the temperature was higher, and the adsorption was spontaneous and endothermic. The qe and η of Cu2+, Pb2+, and Zn2+ decreased in the presence of co-existing ions. The influences among metal ions existed in a binary and ternary ion system. The current study’s results provide a theoretical support for the simultaneous treatment of harmful metal ions in wastewater by MNC.

Facile preparation of a novel iminodisuccinate modified chitin and its excellent properties as a silver bioadsorbent and antibacterial agent

A novel iminodisuccinate modified chitin (ICH) was prepared using crab shells via a one-step facile procedure. The ICH with grafting degree of 1.46 and deacetylation degree of 47.68 % possessed maximum adsorption capacity of 2572.41 mg/g for silver ions (Ag(I)).The ICH also exhibited good selectivity and reusability. The adsorption followed better with the Freundlich isotherm model, while fitted well with both the Pseudo-first-order and Pseudo-second-order kinetics models. The characteristical results showed that the excellent Ag(I) adsorption capability of ICH should be attributed to both looser porous microstructure as well as additional functional groups-grafting molecular. Moreover, the Ag-loaded ICH (ICH-Ag) showed remarkable antibacterial properties against six typical pathogenic bacteria strains (Escherichia coli, Pseudomonas aeruginosa, Enterobacter aerogenes, Salmonella typhimurium, Staphylococcus aureus, and Listeria monocytogenes), with the corresponding 90 % minimal inhibitory concentrations ranged 0.426-0.685 mg/mL. Further study on the silver release, microcell morphology, and metagenomic analysis suggested that many Ag nanoparticles were formed after the Ag(I) adsorption, and the antibacterial mechanisms of the ICH-Ag involved both cell membranes destruction and intracellular metabolism disturbing. This research presented a coupling solution of crab shell wastes treatment with chitin-based bioadsorbents preparation, metal removal and recovery, as well as antibacterial agent production.

Application of new chitosan 2,4-dihydroxyacetophenone Schiff base @SrFe12O19 nanocomposite for remove of Pb(II) ion from aqueous solution

A new chitosan 2,4-dihydroxyacetophenone Schiff base @SrFe₁₂O₁₉ (Cs-SB@SrFe₁₂O₁₉) nanocomposite was successfully prepared by one-pot reaction and fully characterized for its functional groups, morphology, elemental analysis and thermal behavior by FT-IR, XRD, VSM, DSC, TGA, zeta potential, FE-SEM and EDS techniques. The VSM result showed that Cs-SB@SrFe₁₂O₁₉ has M_s of 11.81 emu/g and H_c of 5488 Oe, known as hard magnetic material. Finally, the as-prepared sample utilized as a new sorbent for the removal of Pb(II) ions from aqueous solution by using batch adsorption experiments. The adsorption of Pb(II) was carried out at different pH, contact time and initial dose of Cs-SB@SrFe₁₂O₁₉. The maximum adsorption capacity was found to be 132 mg/g (99 %) at pH 5 and the contact time of 120 min. Finally, the kinetic studies reveals that the adsorption process of Cs-SB@SrFe₁₂O₁₉ followed by the pseudo second order kinetics model. Also, the sample showed excellent recyclable efficiency up to 5 cycles.

Enhancement of Cerium Sorption onto Urea-Functionalized Magnetite Chitosan Microparticles by Sorbent Sulfonation—Application to Ore Leachate

The recovery of strategic metals such as rare earth elements (REEs) requires the development of new sorbents with high sorption capacities and selectivity. The bi-functionality of sorbents showed a remarkable capacity for the enhancement of binding properties. This work compares the sorption properties of magnetic chitosan (MC, prepared by dispersion of hydrothermally precipitated magnetite microparticles (synthesized through Fe(II)/Fe(III) precursors) into chitosan solution and crosslinking with glutaraldehyde) with those of the urea derivative (MC-UR) and its sulfonated derivative (MC-UR/S) for cerium (as an example of REEs). The sorbents were characterized by FTIR, TGA, elemental analysis, SEM-EDX, TEM, VSM, and titration. In a second step, the effect of pH (optimum at pH 5), the uptake kinetics (fitted by the pseudo-first-order rate equation), the sorption isotherms (modeled by the Langmuir equation) are investigated. The successive modifications of magnetic chitosan increases the maximum sorption capacity from 0.28 to 0.845 and 1.25 mmol Ce g−1 (MC, MC-UR, and MC-UR/S, respectively). The bi-functionalization strongly increases the selectivity of the sorbent for Ce(III) through multi-component equimolar solutions (especially at pH 4). The functionalization notably increases the stability at recycling (for at least 5 cycles), using 0.2 M HCl for the complete desorption of cerium from the loaded sorbent. The bi-functionalized sorbent was successfully tested for the recovery of cerium from pre-treated acidic leachates, recovered from low-grade cerium-bearing Egyptian ore.

Fabrication of a lead-free ternary ceramic system for high energy storage applications in dielectric capacitors

The importance of electroceramics is well-recognized in applications of high energy storage density of dielectric ceramic capacitors. Despite the excellent properties, lead-free alternatives are highly desirous owing to their environmental friendliness for energy storage applications. Herein, we provide a facile synthesis of lead-free ferroelectric ceramic perovskite material demonstrating enhanced energy storage density. The ceramic material with a series of composition (1-z) (0.94Na_0.5Bi_0.5TiO₃-0.06BaTiO₃)-zNd_0.33NbO_3, denoted as NBT-BT-zNN, where, z = 0.00, 0.02, 0.04, 0.06, and 0.08 are synthesized by the conventional solid-state mix oxide route. Microphases, microstructures, and energy storage characteristics of the as-synthesized ceramic compositions were determined by advanced ceramic techniques. Powder X-ray diffraction analysis reveals pure single perovskite phases for z = 0 and 0.02, and secondary phases of Bi₂Ti₂O₇ appeared for z = 0.04 and 0.08. Furthermore, scanning electron microscopy analysis demonstrates packed-shaped microstructures with a reduced grain size for these ceramic compositions. The coercive field (E_c) and remnant polarization (P_r) deduced from polarization vs. electric field hysteresis loops determined using an LCR meter demonstrate decreasing trends with the increasing z content for each composition. Consequently, the maximum energy storage density of 3.2 J/cm³, the recoverable stored energy of 2.01 J/cm³, and the efficiency of 62.5% were obtained for the z content of 2 mol% at an applied electric field of 250 kV/cm. This work demonstrates important development in ceramic perovskite for high power energy storage density and efficiency in dielectric capacitors in high-temperature environments. The aforementioned method makes it feasible to modify a binary ceramic composition into a ternary system with highly enhanced energy storage characteristics by incorporating rare earth metals with transition metal oxides in appropriate proportions.

Arsenic in drinking water: overview of removal strategies and role of chitosan biosorbent for its remediation

Accessibility to clean drinking water often remains a crucial task at times. Among other water pollutants, arsenic is considered a more lethal contaminant and has become a serious threat to human life globally. This review discussed the sources, chemistry, distribution, and toxicity of arsenic and various conventional technologies that are in option for its removal from the water system. Nowadays, biosorbents are considered the best option for arsenic-contaminated water treatment. We have mainly focused on the need and potential of biosorbents especially the role of chitosan-based composites for arsenic removal. The chitosan-based sorbents are economically more efficient in terms of their, low toxicity, cost-effectiveness, biodegradability, eco-friendly nature, and reusability. The role of various modification techniques, such as physical and chemical, has also been evaluated to improve the physicochemical properties of biosorbent. The importance of adsorption kinetic and isotherm models and the role of solution pH and pH_PZC for arsenic uptake from the polluted water have also been investigated. Some other potential applications of chitosan-based biosorbents have also been discussed along with its sustainability aspect. Finally, some suggestions have been highlighted for further improvements in this field.

Reusable kaolin impregnated aminated chitosan composite beads for efficient removal of Congo red dye: isotherms, kinetics and thermodynamics studies

In this investigation, Kaolin (K) impregnated aminated chitosan (AM-CTS) composite beads were fabricated with multi-features including low-cost, high performance, renewable and ease of separation for adsorption of anionic Congo red (CR) dye. Characterization tools such as FTIR, XRD, SEM, TGA, BET, XPS and Zeta potential were thoroughly employed to confirm the successful formulation process. The results revealed that K@ AM-CTS composite beads displayed higher specific surface area (128.52 m²/g), while the thermal stability was prominently improved compared to pure AM-CTS. In addition, the adsorption equilibrium of CR dye was accomplished rapidly and closely gotten within 45 min. The removal efficiency was significantly enriched and reached 90.7% with increasing kaolin content up to 0.75%, compared to 20.3 and 58% for pristine kaolin and AM-CTS, respectively. Moreover, the adsorption process obeyed the pseudo-first order kinetic model, while data were agreed with the Freundlich isotherm model with a maximum adsorption capacity reached 104 mg/g at pH 6. Furthermore, D–R isotherm model demonstrated the physical adsorption process of CR dye, which includes the electrostatic interactions, ion exchange and H-bonding. Thermodynamics evidenced the spontaneous and endothermic nature of the adsorption process. Interestingly, the developed K@AM-CTS composites beads showed better reusability for eight consecutive cycles, suggesting their feasible applicability for adsorptive removal anionic dyes from polluted aquatic bodies.

Selective Removal of Iron, Lead, and Copper Metal Ions from Industrial Wastewater by a Novel Cross-Linked Carbazole-Piperazine Copolymer

A novel cross-linked Copolymer (MXM) was synthesized by the polycondensation reaction of 3,6-Diaminocarbazole and piperazine with p-formaldehyde as a cross-linker. The Copolymer was fully characterized by solid ¹³C-NMR and FT-IR. The thermal stability of MXM was investigated by TGA and showed that the Copolymer was stable up to 300 °C. The synthesized polyamine was tested for the removal of iron (Fe²⁺), lead (Pb²⁺), and copper (Cu²⁺) ions from aqueous and industrial wastewater solutions. The effect of pH, concentration and time on the adsorption of iron (Fe²⁺), lead (Pb²⁺), and copper (Cu²⁺) ions was investigated. The adsorption of the studied ions from aqueous solutions onto the MXM polymer occurs following the Freundlich isotherm and pseudo-second-order kinetic models. The intraparticle diffusion model showed that the adsorption mechanism is controlled by film diffusion. The regeneration of MXM showed practical reusability with a loss in capacity of 2–5% in the case of Fe²⁺ and Cu²⁺ ions. The molecular simulation investigations revealed similarities between experimental and theoretical calculations. Industrial wastewater treatment revealed the excellent capabilities and design of MXM to be a potential adsorbent for the removal of heavy metal ions.

Removal of arsenic by metal organic framework/chitosan/carbon nanocomposites: Modeling, optimization, and adsorption studies

In this work removal of the arsenic (As) spiked in water through adsorption using synthesized nanocomposites as a adsorbent. The Zn-BDC@chitosan/carbon nanotube (Zn-BDC@CT/CNT) and Zn-BDC@chitosan/graphene oxide (Zn-BDC@CT/GO) were synthesized from metal organic framework, carbon nanotube/graphene oxide and natural polysaccharide. Results of adsorption experiments showed that the Zn-BDC@CT/GO possessed a higher adsorption capacity than that of the Zn-BDC@CT/CNT. A study on the adsorption of As onto Zn-BDC@CT/GO was conducted and the process parameters were optimized by response surface methodology (RSM). A five-level, four-factor central composite design (CCD) has been used to determine the effect of various process parameters on As uptake from aqueous solution. By using this design a total of 20 adsorption experimental data were fitted. The regression analysis showed good fit of the experimental data to the second-order polynomial model with coefficient of determination (R²) value of 0.9997 and model F-value of 1099.97. The adsorption matched with the pseudo-second-order model and the Freundlich model. The thermodynamic parameters revealed that the nature of adsorption was feasible, spontaneous and endothermic process. Adsorption of As in the presence of other competitive ions was not significantly affected The effective adsorption performance also sustained even after ten adsorption-desorption cycles, indicating favorable reusability.

Synthesis and characterization of chitosan-vermiculite-lignin ternary composite as an adsorbent for effective removal of uranyl ions from aqueous solution: Experimental and theoretical analyses

Chitosan (Ch), vermiculite (V) and lignin (L) were used as the components of a natural composite adsorbent (Ch-VL) for the removal of the UO₂²⁺ ions in aqueous solutions. During the study, we recorded and analyzed the initial UO₂²⁺ ion concentration, initial pH, contact time, temperature, and recovery. The recycling performance of the Ch-VL composite was assessed by three sequential adsorption/desorption experiments. Adsorption performance of the Ch-VL composite for UO₂²⁺ ions was 600 mg L^-1 at pH 4.5 and temperature of 25 °C. Thermodynamic findings, ΔH⁰:28.1 kJ mol^-1, and ΔG⁰:-14.1 kJ mol^-1 showed that adsorption behavior was endothermic and spontaneous. Its maximum adsorption capacity was 0.322 mol kg^-1, obtained from the Langmuir isotherm model. The adsorption kinetics indicated that it followed the pseudo-second-order and intraparticle diffusion rate kinetics. The adsorption thermodynamic shown indicated that the UO₂²⁺ ion adsorption was both spontaneous and endothermic. The adsorption process was enlightened by FT-IR and SEM-EDX analyses. The study suggested a simple and cost-effective approach for the removal of toxic UO₂²⁺ ions from wastewater. To highlight the adsorption mechanism, DFT calculations were performed. Theoretical results are in good agreement with experimental observations.

Recent Advancements in Microbial Polysaccharides: Synthesis and Applications

Polysaccharide materials are widely applied in different applications including food, food packaging, drug delivery, tissue engineering, wound dressing, wastewater treatment, and bioremediation sectors. They were used in these domains due to their efficient, cost-effective, non-toxicity, biocompatibility, and biodegradability. As is known, polysaccharides can be synthesized by different simple, facile, and effective methods. Of these polysaccharides are cellulose, Arabic gum, sodium alginate, chitosan, chitin, curdlan, dextran, pectin, xanthan, pullulan, and so on. In this current article review, we focused on discussing the synthesis and potential applications of microbial polysaccharides. The biosynthesis of polysaccharides from microbial sources has been considered. Moreover, the utilization of molecular biology tools to modify the structure of polysaccharides has been covered. Such polysaccharides provide potential characteristics to transfer toxic compounds and decrease their resilience to the soil. Genetically modified microorganisms not only improve yield of polysaccharides, but also allow economically efficient production. With the rapid advancement of science and medicine, biosynthesis of polysaccharides research has become increasingly important. Synthetic biology approaches can play a critical role in developing polysaccharides in simple and facile ways. In addition, potential applications of microbial polysaccharides in different fields with a particular focus on food applications have been assessed.

Biodegradation of Polylactic Acid-Based Bio Composites Reinforced with Chitosan and Essential Oils as Anti-Microbial Material for Food Packaging

This study aims to produce and investigate the potential of biodegradable Polylactic Acid (PLA)-based composites mixed with chitosan and Turmeric Essential Oil (TEO) as an anti-microbial biomaterial. PLA has good barrier properties for moisture, so it is suitable for use as a raw material for making packaging and is included in the GRAS (Generally Recognized As Safe). Chitosan is a non-toxic and antibacterial cationic polysaccharide that needs to be improved in its ability to fight microbes. TEO must be added to increase antibacterial properties due to a large number of hydroxyl (-OH) and carbonyl functional groups. The samples were prepared in three different variations: 2 g of chitosan, 0 mL TEO and 0 mL glycerol (Biofilm 1), 3 g of chitosan, 0.3 mL TEO and 0.5 mL of glycerol (Biofilm 2), and 4 g of chitosan, 0.3 of TEO and 0.5 mL of glycerol (Biofilm 3). The final product was characterized by its functional group through Fourier transform infrared (FTIR); the functional groups contained by the addition of TEO are C-H, C=O, O-H, and N-H with the extraction method, and as indicated by the emergence of a wide band at 3503 cm-1, turmeric essential oil interacts with the polymer matrix by creating intermolecular hydrogen bonds between their terminal hydroxyl group and the carbonyl groups of the ester moieties of both PLA and Chitosan. Thermogravimetric analysis (TGA) of PLA as biofilms, the maximum temperature of a biofilm was observed at 315.74 °C in the variation of 4 g chitosan, 0.3 mL TEO, and 0.5 mL glycerol (Biofilm 3). Morphological conditions analyzed under scanning electron microscopy (SEM) showed that the addition of TEO inside the chitosan interlayer bound chitosan molecules to produce solid particles. Chitosan and TEO showed increased anti-bacterial activity in the anti-microbial test. Furthermore, after 12 days of exposure to open areas, the biofilms generated were able to resist S. aureus and E. coli bacteria.

Hydrogels derived from galactoglucomannan hemicellulose with inorganic contaminant removal properties

The adsorption of Cu(ii), Cd(ii), and Pb(ii) ions onto hydrogels derived from modified galactoglucomannan (GGM) hemicellulose was studied. GGM hemicellulose was modified with methacrylate groups (GGM-MA) to incorporate vinyl groups into the polymeric structure, which reacted later with synthetic monomers such as 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS). The results show that all the synthesized hydrogels were capable of adsorbing contaminating ions with high adsorption efficiency during short periods of time. Furthermore, an increase in the content of GGM-MA generated a hydrogel (H3) with a similar ion adsorption property to the other hydrogels but with a lesser degree of swelling. The H3 hydrogel had an adsorption capacity of 60.0 mg g⁻¹ Cd(ii), 78.9 mg g⁻¹ Cu(ii), and 174.9 mg g⁻¹ Pb(ii) at 25 °C. This result shows that modified GGM hemicelluloses can be employed as renewable adsorbents to remove Cu(ii), Cd(ii), and Pb(ii) ions from aqueous solutions.

The adsorption of Cu(ii), Cd(ii), and Pb(ii) ions onto hydrogels derived from modified galactoglucomannan (GGM) hemicellulose was studied.

Adsorption of Metallic Ions on Amidoxime-Chitosan/Cellulose Hydrogels

Adsorption using natural compounds is an attractive separation technique for recovering heavy metals from aqueous media. Although chitosan, which is a natural polysaccharide, is an environmentally benign adsorbent, it dissolves in an acidic aqueous medium. In this study, we prepared adsorbents consisting of chitosan modified with amidoxime groups for improving metal adsorptivity, and cellulose for improving gel stability using an ionic liquid, and examined their adsorption characteristics for metal ions. The prepared amidoxime-chitosan/cellulose hydrogels had a mechanical strength without cross-linking. All the investigated metals were adsorbed on the amidoxime-chitosan/cellulose hydrogels in the following adsorptivity order: Cu ≈ Ag > Ni > Zn. The adsorptivity of the metal ions increased with pH due to a proton exchange reaction. From the Langmuir adsorption isotherm, the Langmuir constant for Cu exceeded those of other metals because amidoxime has higher Cu affinity. The pseudo-second-order reaction model best described the adsorption kinetics with metal chelate formation being the rate-determining step. Because amidoxime-chitosan/cellulose hydrogels had higher physical stability and higher Cu selectivity, they were found to be a promising, environmentally benign adsorbent.