Ag/Pt-modified TiO2 nanoparticles for toluene photooxidation in the gas phase

The selection of a nitrogen precursor for the construction of N-doped titanium dioxide with enhanced photocatalytic activity for the removal of gaseous toluene

The preparation of nitrogen-doped TiO2 (i.e., N-TiO2) catalysts is a highly effective option to improve the photocatalytic activity of TiO2. Nonetheless, relatively little is known about the effects of dopant precursors selected for their preparation with regard to the photocatalytic efficacy. In this study, three types of dopants are selected and used as N sources (urea (U), melamine (M), and aqueous ammonia (A)) for N-TiO2 samples with the name codes of NTU, NTM, and NTA, respectively. The photocatalytic efficacy of these N-TiO2 samples is examined against toluene in a packed bed flow reactor. Under optimal conditions (e.g., relative humidity (RH) = 20% and gas hourly space velocity (GHSV) = 1698 h-1), the superiority of NTA is evident over others with a quantum efficiency (QE) of 7.03 × 10-4 molecules photon-1, a space time yield (STY) of 1.38 × 10-4 molecules photon-1 mg-1, and a specific clean air delivery rate (SCADR) of 1148.8 L g-1 h-1. The analysis based on in-situ diffuse reflectance infrared Fourier transform spectroscopy and gas chromatography-mass spectrometry confirms the formation of several intermediates such as benzyl alcohol, benzaldehyde, benzoic acid, and alkane species through ring opening reactions. In addition, the prepared NTA photocatalyst exhibits the highest toluene photocatalytic degradation efficiency among all TiO2-based catalysts surveyed to date. Overall, this study offers as a valuable guideline for the development of advanced TiO2 catalytic systems (such as N-TiO2) for the treatment of aromatic hydrocarbons in indoor air.

Enhancing air treatment through controlled fabrication of transition metal-doped titanium dioxide nanocomposites for photocatalytic toluene degradation

Rapid industrial growth and urbanization have resulted in a significant rise in environmental pollution issues, particularly indoor air pollutants. As a result, it is crucial to design and develop technologies and/or catalysts that are not only cost-effective but also promising high performance and practical applicability. However, achieving this goal has been so far remained a challenging task. Herein, a series of transition metal M - TiO2 (M = W, Fe, Mn) nanocrystals was prepared for photocatalytic degradation of volatile organic compounds (VOCs), i.e., toluene. Of the nanocomposites tested, W-TiO2 showed significantly improved photocatalytic activity for VOC degradation under UV irradiation compared to the others. In particular, the optimized W dopant amount of 0.5 wt% resulted in the outstanding degradation performance of toluene (96%) for the obtained W-TiO2(0.5%) nanocomposite. Moreover, W-TiO2(0.5%) nanocomposite exhibited good stability for 32 h working under high toluene concentration (10 ppm) compared to the pristine TiO2. The current work demonstrates the potential usage of M - TiO2 nanocrystals, particularly W-TiO2(0.5%), as a promising photocatalyst for efficient VOCs degradation.

Chemical characterization of volatile organic compounds (VOCs) emitted from multiple cooking cuisines and purification efficiency assessments

Cooking process can produce abundant volatile organic compounds (VOCs), which are harmful to environment and human health. Therefore, we conducted a comprehensive analysis in which VOCs emissions from multiple cuisines have been sampled based on the simulation and acquisition platform, involving concentration characteristics, ozone formation potential (OFP) and purification efficiency assessments. VOCs emissions varied from 1828.5 to 14,355.1 µg/m³, with the maximum and minimum values from Barbecue and Family cuisine, respectively. Alkanes and alcohol had higher contributions to VOCs from Sichuan and Hunan cuisine (64.1%), Family cuisine (66.3%), Shandong cuisine (69.1%) and Cantonese cuisine (69.8%), with the dominant VOCs species of ethanol, isobutane and n-butane. In comparison, alcohols (79.5%) were abundant for Huaiyang cuisine, while alkanes (19.7%), alkenes (35.9%) and haloalkanes (22.9%) accounted for higher proportions from Barbecue. Specially, carbon tetrachloride, n-hexylene and 1-butene were the most abundant VOCs species for Barbecue, ranging from 8.8% to 14.6%. The highest OFP occurred in Barbecue. The sensitive species of OFP for Huaiyang cuisine were alcohols, while other cuisines were alkenes. Purification efficiency assessments shed light on the removal differences of individual and synergistic control technologies. VOCs emissions exhibited a strong dependence on the photocatalytic oxidation, with the removal efficiencies of 29.0%-54.4%. However, the high voltage electrostatic, wet purification and mechanical separation techniques played a mediocre or even counterproductive role in the VOCs reduction, meanwhile collaborative control technologies could not significantly improve the removal efficiency. Our results identified more effective control technologies, which were conductive to alleviating air pollution from cooking emissions.

Enhancing the visible-light photoactivity of silica-supported TiO2 for the photocatalytic treatment of pharmaceuticals in water

Catalyst samples based on SiO₂-supported TiO₂ were prepared with the incorporation of Ag (metal), S (nonmetal), and ZnO@S (semiconductor and nonmetal). The materials were evaluated regarding their morphological, optical, and crystalline properties as well as their photoactivity under visible and ultraviolet light toward the degradation rate of a model emerging pollutant, acetaminophen (ACT). All modified materials exhibited improved performance over the undoped catalyst. The Ag-doped catalyst achieved the largest degradation under visible radiation (about 30% in 120 min), whereas under ultraviolet irradiation, the ZnO@S-doped sample exhibited the best performance (about 62% in 120 min). A Doehlert design was carried out to evaluate the influence of pH and temperature on the photoactivity of Ag-TiO₂/SiO₂. In addition, the role of each reactive species in the photodegradation reaction was investigated by radical scavenger experiments, and the superoxide radical anion O₂^•- was shown to be the predominant reactive species. The stability of the Ag-TiO₂/SiO₂ material under ultraviolet and visible light was confirmed after five successive operation cycles, showing a reasonable (about 50%) loss of activity under visible irradiation and a slight improvement (about 13%) under UV light, as a result of the photo-reduction of Ag⁺. Lastly, the effect of the initial pollutant concentration showed that ACT degradation using Ag-TiO₂/SiO₂ follows the Langmuir-Hinshelwood kinetics, with intrinsic reaction rate k = 2.71 × 10^-4 mmol L^-1 min^-1 under visible-light radiation.

Granular-carbon supported nano noble-metal (Au, Pd, Au-Pd): new dual-functional adsorbent/catalysts for effective removal of toluene at low-temperature and humid condition

Treatment of the volatile organic compounds (VOCs) especially aromatic compounds such as toluene at low temperature and in the highly humid condition is currently a great challenge. New dual functional adsorbent/catalysts have been developed in this study to minimize the mass-transfer limitation at low temperature. The ready-to-practically-use materials, which consisted nano-sized noble metal (Au, Pd, Au-Pd) supported on granular carbon (GC) have been prepared using a metal-sol method. The surface morphology, and structure of these granular materials were characterized to confirm the presence of nano-sized noble metal on the GC as well as the properties of the dual functional adsorbent/catalyst. The results of catalytic performance revealed that the presence of Pd played an important role in the formation of nano Au particles, which were the catalytic active-site for toluene oxidation. At 60% relative humidity and 150°C the dual functional adsorbent/catalyst, Au-Pd/GC, exhibited 97.2% toluene removal. Importantly, the kinetic analysis for the catalytic oxidation of nano-sized 0.5%Au-0.27%Pd/GC catalyst showed that the Langmuir-Hinshelwood mechanism provided a good fit towards the experimental data and allowed to determine the kinetic parameters of the reaction-rate law -rA=k⋅KA⋅CA1+KA⋅CA⋅KO2⋅CO21+KO2.CO2. The activation energy, adsorption enthalpy of toluene, and oxygen on the catalyst were reported.

Bimetallic Catalysts for Volatile Organic Compound Oxidation

In recent years, the impending necessity to improve the quality of outdoor and indoor air has produced a constant increase of investigations in the methodologies to remove and/or to decrease the emission of volatile organic compounds (VOCs). Among the various strategies for VOC elimination, catalytic oxidation and recently photocatalytic oxidation are regarded as some of the most promising technologies for VOC total oxidation from urban and industrial waste streams. This work is focused on bimetallic supported catalysts, investigating systematically the progress and developments in the design of these materials. In particular, we highlight their advantages compared to those of their monometallic counterparts in terms of catalytic performance and physicochemical properties (catalytic stability and reusability). The formation of a synergistic effect between the two metals is the key feature of these particular catalysts. This review examines the state-of-the-art of a peculiar sector (the bimetallic systems) belonging to a wide area (i.e., the several catalysts used for VOC removal) with the aim to contribute to further increase the knowledge of the catalytic materials for VOC removal, stressing the promising potential applications of the bimetallic catalysts in the air purification.

The Response of UV/Blue Light and Ozone Sensing Using Ag-TiO2 Planar Nanocomposite Thin Film

We successfully fabricated a planar nanocomposite film that uses a composite of silver nanoparticles and titanium dioxide film (Ag-TiO₂) for ultraviolet (UV) and blue light detection and application in ozone gas sensor. Ultraviolet-visible spectra revealed that silver nanoparticles have a strong surface plasmon resonance (SPR) effect. A strong redshift of the plasmonic peak when the silver nanoparticles covered the TiO₂ thin film was observed. The value of conductivity change for the Ag-TiO₂ composite is 4–8 times greater than that of TiO₂ film under UV and blue light irradiation. The Ag-TiO₂ nanocomposite film successfully sensed 100 ppb ozone. The gas response of the composite film increased by roughly six and four times under UV and blue light irradiation, respectively. We demonstrated that a Ag-TiO₂ composite gas sensor can be used with visible light (blue). The planar composite significantly enhances photo catalysis. The composite films have practical application potential for wearable devices.

A chemoinformatics approach for the characterization of hybrid nanomaterials: safer and efficient design perspective

In this study, photocatalytic properties and in vitro cytotoxicity of 29 TiO2-based multi-component nanomaterials (i.e., hybrids of more than two composition types of nanoparticles) were evaluated using a combination of the experimental testing and supervised machine learning modeling. TiO2-based multi-component nanomaterials with metal clusters of silver, and their mixtures with gold, palladium, and platinum were successfully synthesized. Two activities, photocatalytic activity and cytotoxicity, were studied. A novel cheminformatic approach was developed and applied for the computational representation of the photocatalytic activity and cytotoxicity effect. In this approach, features of investigated TiO2-based hybrid nanomaterials were reflected by a series of novel additive descriptors for hybrid and hybrid nanostructures (denoted as "hybrid nanosctructure descriptors"). These descriptors are based on quantum chemical calculations and the Smoluchowski equation. The obtained experimental data and calculated hybrid-nanostructure descriptors were used to develop novel predictive Quantitative Structure-Activity Relationship computational models (called "nano-QSARmix"). The proposed modeling approach is an initial step in the understanding of the relationships between physicochemical properties of hybrid nanoparticles, their toxicity, and photochemical activity under UV-vis irradiation. Acquired knowledge supports the safe-by-design approaches relevant to the development of efficient hybrid nanomaterials with reduced hazardous effects.

UV-Vis-Induced Degradation of Phenol over Magnetic Photocatalysts Modified with Pt, Pd, Cu and Au Nanoparticles

The combination of TiO₂ photocatalyst and magnetic oxide nanoparticles enhances the separation and recoverable properties of nanosized TiO₂ photocatalyst. Metal-modified (Me = Pd, Au, Pt, Cu) TiO₂/SiO₂@Fe₃O₄ nanocomposites were prepared by an ultrasonic-assisted sol-gel method. All prepared samples were characterized by X-ray powder diffraction (XRD) analysis, Brunauer-Emmett-Teller (BET) method, X-ray photoelectron spectroscopy (XPS), scanning transmission electron microscopy (STEM), Mott-Schottky analysis and photoluminescence spectroscopy (PL). Phenol oxidation pathways of magnetic photocatalysts modified with Pt, Pd, Cu and Au nanoparticles proceeded by generation of reactive oxygen species, which oxidized phenol to benzoquinone, hydroquinone and catechol. Benzoquinone and maleic acid were products, which were determined in the hydroquinone oxidation pathway. The highest mineralization rate was observed for Pd-TiO₂/SiO₂@Fe₃O₄ and Cu-TiO₂/SiO₂@Fe₃O₄ photocatalysts, which produced the highest concentration of catechol during photocatalytic reaction. For Pt-TiO₂/SiO₂@Fe₃O₄ nanocomposite, a lack of catechol after 60 min of irradiation resulted in low mineralization rate (CO₂ formation). It is proposed that the enhanced photocatalytic activity of palladium and copper-modified photocatalysts is related to an increase in the amount of adsorption sites and efficient charge carrier separation, whereas the keto-enol tautomeric equilibrium retards the rate of phenol photomineralization on Au-TiO₂/SiO₂@Fe₃O₄. The magnetization hysteresis loop indicated that the obtained hybrid photocatalyst showed magnetic properties and therefore could be easily separated after treatment process.

Growth, Structure, and Photocatalytic Properties of Hierarchical V₂O₅-TiO₂ Nanotube Arrays Obtained from the One-step Anodic Oxidation of Ti-V Alloys

V₂O₅-TiO₂ mixed oxide nanotube (NT) layers were successfully prepared via the one-step anodization of Ti-V alloys. The obtained samples were characterized by scanning electron microscopy (SEM), UV-Vis absorption, photoluminescence spectroscopy, energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (DRX), and micro-Raman spectroscopy. The effect of the applied voltage (30-50 V), vanadium content (5-15 wt %) in the alloy, and water content (2-10 vol %) in an ethylene glycol-based electrolyte was studied systematically to determine their influence on the morphology, and for the first-time, on the photocatalytic properties of these nanomaterials. The morphology of the samples varied from sponge-like to highly-organized nanotubular structures. The vanadium content in the alloy was found to have the highest influence on the morphology and the sample with the lowest vanadium content (5 wt %) exhibited the best auto-alignment and self-organization (length = 1 μm, diameter = 86 nm and wall thickness = 11 nm). Additionally, a probable growth mechanism of V₂O₅-TiO₂ nanotubes (NTs) over the Ti-V alloys was presented. Toluene, in the gas phase, was effectively removed through photodegradation under visible light (LEDs, λmax = 465 nm) in the presence of the modified TiO₂ nanostructures. The highest degradation value was 35% after 60 min of irradiation. V₂O₅ species were ascribed as the main structures responsible for the generation of photoactive e- and h⁺ under Vis light and a possible excitation mechanism was proposed.

Noble metal-based bimetallic nanoparticles: the effect of the structure on the optical, catalytic and photocatalytic properties

Nanoparticles composed of two different metal elements show novel electronic, optical, catalytic or photocatalytic properties from monometallic nanoparticles. Bimetallic nanoparticles could show not only the combination of the properties related to the presence of two individual metals, but also new properties due to a synergy between two metals. The structure of bimetallic nanoparticles can be oriented in random alloy, alloy with an intermetallic compound, cluster-in-cluster or core-shell structures and is strictly dependent on the relative strengths of metal-metal bond, surface energies of bulk elements, relative atomic sizes, preparation method and conditions, etc. In this review, selected properties, such as structure, optical, catalytic and photocatalytic of noble metals-based bimetallic nanoparticles, are discussed together with preparation routes. The effects of preparation method conditions as well as metal properties on the final structure of bimetallic nanoparticles (from alloy to core-shell structure) are followed. The role of bimetallic nanoparticles in heterogeneous catalysis and photocatalysis are discussed. Furthermore, structure and optical characteristics of bimetallic nanoparticles are described in relation to the some features of monometallic NPs. Such a complex approach allows to systematize knowledge and to identify the future direction of research.

Mechanistic study of visible light driven photocatalytic degradation of EDC 17α-ethinyl estradiol and azo dye Acid Black-52: phytotoxicity assessment of intermediates

The present study evaluated the phytotoxicity of degraded intermediates of an endocrine-disrupting compound (EDC) 17α-ethinyl estradiol (EE2) and toxic azo dye Acid Black-52 (AB-52) in photocatalytic degradation.

Organic pollutants removal in wastewater by heterogeneous photocatalytic ozonation

Heterogeneous photocatalysis and ozonation are robust advanced oxidation processes for eliminating organic contaminants in wastewater. The combination of these two methods is carried out in order to enhance the overall mineralization of refractory organics. An apparent synergism between heterogeneous photocatalysis and ozonation has been demonstrated in many literatures, which gives rise to an improvement of total organic carbon removal. The present overview dissects the heterogeneous catalysts and the influences of different operational parameters, followed by the discussion on the kinetics, mechanism, economic feasibility and future trends of this integrated technology. The enhanced oxidation rate mainly results from a large amount of hydroxyl radicals generated from a synergistically induced decomposition of dissolved ozone, besides superoxide ion radicals and the photo-induced holes. Six reaction pathways possibly exist for the generation of hydroxyl radicals in the reaction mechanism of heterogeneous photocatalytic ozonation.

Supported copper and cobalt oxides on activated carbon for simultaneous oxidation of toluene and cyclohexane in air

Dispersed nano mixed copper–cobalt oxides bimetallic catalysts were prepared by deposition–precipitation method for simultaneous and complete oxidation of toluene and cyclohexane.