Composite catalytic systems: A strategy for developing the low temperature NH3-SCR catalysts with satisfactory SO2 and H2O tolerance

Facile H2O-Contributed O2 Activation Strategy over Mn-Based SCR Catalysts to Counteract SO2 Poisoning

Mn-based catalysts preferred in low-temperature selective catalytic reduction (SCR) are susceptible to SO2 poisoning. The stubborn sulfates make insufficient O2 activation and result in deficient reactive oxygen species (ROS) for activating reaction molecules. H2O has long been regarded as an accomplice to SO2, hastening catalyst deactivation. However, such a negative impression of the SCR reaction was reversed by our recent research. Here, we reported a H2O contribution over Mn-based SCR catalysts to counteract SO2 poisoning through accessible O2 activation, in which O2 was synergistically activated with H2O to generate ROS for less deactivation and more expected regeneration. The resulting ROS benefited from the energetically favorable route supported by water-induced Ea reduction and was actively involved in the NH3 activation and NO oxidation process. Besides, ROS maintained high stability over the SO2 + H2O-deactivated γ-MnO2 catalyst throughout the mild thermal treatment, achieving complete regeneration of its own NO disposal ability. This strategy was proven to be universally applicable to other Mn-based catalysts.

Catalytic oxidation of chlorobenzene and PCDD/Fs over V2O5-WO3/TiO2: insights into the component effect and reaction mechanism

In this work, titania supported catalysts (V-W/Ti) with different vanadium-tungsten contents were prepared and evaluated in the catalytic oxidation of chlorobenzene, which was used as the model compound of dioxins. The results showed that V₂O₅ is the main active component for chlorobenzene oxidation, and doping of WO₃ affects the valence distributions of vanadium, contributing a bimetallic synergistic effect. The catalysts were investigated by XRD, SEM-EDS mapping, Raman, and XPS, and the changes in V element valence state and chlorine content on fresh and used catalysts were observed by XPS. Moreover, in situ FTIR studies and chlorine balance were also conducted, the addition of WO₃ is helpful to the breakage of C-Cl, and a reaction mechanism for the catalytic oxidation of chlorobenzene was proposed. 3 V-5 W/Ti catalyst with better catalytic activity was selected for catalytic oxidation of PCDD/Fs using a lab scale PCDD/Fs generating and decomposing system. The degradation efficiency was 66.5% at 200 °C and 62.2% at 300 °C, which indicated that the low reaction temperature of 200 °C was conducive to the catalytic degradation of PCDDs, while the high temperature of 300 °C was facilitated the degradation of PCDFs.

Recent advances and perspectives in the resistance of SO2 and H2O of cerium-based catalysts for NOx selective catalytic reduction with ammonia

This review emphasizes the aspects related to cerium-based catalysts at different levels: metal modification, preparation methods, structures, and reaction mechanisms.

Exceptional Low-Temperature CO Oxidation over Noble-Metal-Free Iron-Doped Hollandites: An In-Depth Analysis of the Influence of the Defect Structure on Catalytic Performance

A family of iron-doped manganese-related hollandites, K_xMn_1–yFe_yO_2−δ (0 ≤ y ≤ 0.15), with high performance in CO oxidation have been prepared. Among them, the most active catalyst, K_0.11Mn_0.876Fe_0.123O_1.80(OH)_0.09, is able to oxidize more than 50% of CO at room temperature. Detailed compositional and structural characterization studies, using a wide battery of thermogravimetric, spectroscopic, and diffractometric techniques, both at macroscopic and microscopic levels, have provided essential information about this never-reported behavior, which relates to the oxidation state of manganese. Neutron diffraction studies evidence that the above compound stabilizes hydroxyl groups at the midpoints of the tunnel edges as in isostructural β-FeOOH. The presence of oxygen and hydroxyl species at the anion sublattice and Mn³⁺, confirmed by electron energy loss spectroscopy, appears to play a key role in the catalytic activity of this doped hollandite oxide. The analysis of these detailed structural features has allowed us to point out the key role of both OH groups and Mn³⁺ content in these materials, which are able to effectively transform CO without involving any critical, noble metal in the catalyst formulation.

The effect of SO2 on the structural evolution of a supported Mn2V2O7 catalyst and its DeNOx performance

Mn₂V₂O₇/TiO₂ can decompose to form sulfated VO_x and MnSO₄ on TiO₂ in the presence of SO₂, and the corresponding DeNO_x efficiency increases above 250 °C but it decreases below 250 °C.

Density functional theory (DFT) studies of vanadium-titanium based selective catalytic reduction (SCR) catalysts

Based on density functional theory (DFT) and basic structure models, the chemical reactions on the surface of vanadium-titanium based selective catalytic reduction (SCR) denitrification catalysts were summarized. Reasonable structural models (non-periodic and periodic structural models) are the basis of density functional calculations. A periodic structure model was more appropriate to represent the catalyst surface, and its theoretical calculation results were more comparable with the experimental results than a non-periodic model. It is generally believed that the SCR mechanism where NH₃ and NO react to produce N₂ and H₂O follows an Eley-Rideal type mechanism. NH₂NO was found to be an important intermediate in the SCR reaction, with multiple production routes. Simultaneously, the effects of H₂O, SO₂ and metal on SCR catalysts were also summarized.

Preparation of Mesoporous Mn-Ce-Ti-O Aerogels by a One-Pot Sol-Gel Method for Selective Catalytic Reduction of NO with NH3

Novel Mn-Ce-Ti-O composite aerogels with large mesopore size were prepared via a one-pot sol-gel method by using propylene oxide as a network gel inducer and ethyl acetoacetate as a complexing agent. The effect of calcination temperature (400, 500, 600, and 700 °C) on the NH3-selective catalytic reduction (SCR) performance of the obtained Mn-Ce-Ti-O composite aerogels was investigated. The results show that the Mn-Ce-Ti-O catalyst calcined at 600 °C exhibits the highest NH3-SCR activity and lowest apparent activation energy due to its most abundant Lewis acid sites and best reducibility. The NO conversion of the MCTO-600 catalyst maintains 100% at 200 °C in the presence of 100 ppm SO2, showing the superior resistance to SO2 poisoning as compared with the MnOx-CeO2-TiO2 catalysts reported the literature. This should be mainly attributed to its large mesopore sizes with an average pore size of 32 nm and abundant Lewis acid sites. The former fact facilitates the decomposition of NH4HSO4, and the latter fact reduces vapor pressure of NH3. The NH3-SCR process on the MCTO-600 catalyst follows both the Eley-Rideal (E-R) mechanism and the Langmuir-Hinshelwood (L-H) mechanism.

A Critical Review of Recent Progress and Perspective in Practical Denitration Application

Nitrogen oxides (NOx) represent one of the main sources of haze and pollution of the atmosphere as well as the causes of photochemical smog and acid rain. Furthermore, it poses a serious threat to human health. With the increasing emission of NOx, it is urgent to control NOx. According to the different mechanisms of NOx removal methods, this paper elaborated on the adsorption method represented by activated carbon adsorption, analyzed the oxidation method represented by Fenton oxidation, discussed the reduction method represented by selective catalytic reduction, and summarized the plasma method represented by plasma-modified catalyst to remove NOx. At the same time, the current research status and existing problems of different NOx removal technologies were revealed and the future development prospects were forecasted.

Annealing Strategies for the Improvement of Low-Temperature NH3-Selective Catalytic Reduction Activity of CrMnO x Catalysts

Annealing strategies for the citrate complexation-combustion method have been explored as a simple approach for improving the catalytic activity of mixed Cr-Mn oxides for the NH3-selective catalytic reduction of NO x . Materials prepared at 300 and 400 °C possess largely amorphous structures, consistent with highly dispersed Cr/Mn components. Annealing at 300 °C for 10 h facilitates the formation of catalysts possessing the largest surface area, reducibility, acidity, and activity window (92-239 °C), while areal activity is measured at 3.8 nmol s-1 m-2 and is comparable to values obtained for materials prepared at 400 °C. Conversely, shorter annealing times of 1 and 5 h at 300 °C produce materials that transform NO x about 2-3 times faster at equivalent surface area. Characterization demonstrates that simple annealing strategies have significant impact on the physiochemical and textural properties of these materials. Moreover, reducibility, Oα species, and acidity were correlated against areal activity, but only the latter exhibited a near-linear correlation, indicating its dominance in controlling surface reaction rates.