Visible photoresponse of TiO2 nanotubes in comparison to that of nanoparticles and anodic thin film

The Challenges and Opportunities for TiO2 Nanostructures in Gas Sensing

Chemiresistive gas sensors based on metal oxides have been widely applied in industrial monitoring, medical diagnosis, environmental pollutant detection, and food safety. To further enhance the gas sensing performance, researchers have worked to modify the structure and function of the material so that it can adapt to different gas types and environmental conditions. Among the numerous gas-sensitive materials, n-type TiO2 semiconductors are a focus of attention for their high stability, excellent biosafety, controllable carrier concentration, and low manufacturing cost. This Perspective first introduces the sensing mechanism of TiO2 nanostructures and composite TiO2-based nanomaterials and then analyzes the relationship between their gas-sensitive properties and their structure and composition, focusing also on technical issues such as doping, heterojunctions, and functional applications. The applications and challenges of TiO2-based nanostructured gas sensors in food safety, medical diagnosis, environmental detection, and other fields are also summarized in detail. Finally, in the context of their practical application challenges, future development technologies and new sensing concepts are explored, providing new ideas and directions for the development of multifunctional intelligent gas sensors in various application fields.

Photoactivity of amorphous and crystalline TiO2 nanotube arrays (TNA) films in gas phase CO2 reduction to methane with simultaneous H2 production

This study assessed the photoactivity of amorphous and crystalline TiO2 nanotube arrays (TNA) films in gas phase CO2 reduction. The TNA photocatalysts were fabricated by titanium anodization and submitted to an annealing treatment for crystallization and/or cathodic reduction to introduce Ti3+ and oxygen vacancies into the TiO2 structure. The cathodic reduction demonstrated a significant effect on the generated photocurrent. The photoactivity of the four TNA catalysts in CO2 reduction with water vapor was evaluated under UV irradiation for 3 h, where CH4 and H2 were detected as products. The annealed sample exhibited the best performance towards methane with a production rate of 78 μmol gcat-1 h-1, followed by the amorphous film, which also exhibited an impressive formation rate of 64 μmol gcat-1 h-1. The amorphous and reduced-amorphous films exhibited outstanding photoactivity regarding H2 production (142 and 144 μmol gcat-1 h-1, respectively). The annealed catalyst also revealed a good performance for H2 production (132 μmol gcat-1 h-1) and high stability up to five reaction cycles. Molecular dynamic simulations demonstrated the changes in the band structure by introducing oxygen vacancies. The topics covered in this study contribute to the Sustainable Development Goals (SDG), involving affordable and clean energy (SDG#7) and industry, innovation, and infrastructure (SDG#9).

Wide Response Range Photoelectrochemical UV Detector Based on Anodized TiO2-Nanotubes@Ti@quartz Structure

Conventional sandwich structure photoelectrochemical UV detectors cannot detect UV light below 300 nm due to UV filtering problems. In this work, we propose to place the electron collector inside the active material, thus avoiding the effect of electrodes on light absorption. We obtained a TiO2-nanotubes@Ti@quartz photoanode structure by precise treatment of a commercial Ti mesh by anodic oxidation. The structure can absorb any light in the near-UV band and has superior stability to other metal electrodes. The final encapsulated photoelectrochemical UV detectors exhibit good switching characteristics with a response time below 100 ms. The mechanism of the oxidation conditions on the photovoltaic performance of the device was investigated by the electrochemical impedance method, and we obtained the optimal synthesis conditions. Response tests under continuous spectroscopy confirm that the response range of the device is extended from 300-400 nm to 240-400 nm. This idea of a built-in collector is an effective way to extend the response range of a photoelectrochemical detector.

Experimental Studies on TiO2 NT with Metal Dopants through Co-Precipitation, Sol-Gel, Hydrothermal Scheme and Corresponding Computational Molecular Evaluations

In the last decade, TiO₂ nanotubes have attracted the attention of the scientific community and industry due to their exceptional photocatalytic properties, opening a wide range of additional applications in the fields of renewable energy, sensors, supercapacitors, and the pharmaceutical industry. However, their use is limited because their band gap is tied to the visible light spectrum. Therefore, it is essential to dope them with metals to extend their physicochemical advantages. In this review, we provide a brief overview of the preparation of metal-doped TiO₂ nanotubes. We address hydrothermal and alteration methods that have been used to study the effects of different metal dopants on the structural, morphological, and optoelectrical properties of anatase and rutile nanotubes. The progress of DFT studies on the metal doping of TiO₂ nanoparticles is discussed. In addition, the traditional models and their confirmation of the results of the experiment with TiO₂ nanotubes are reviewed, as well as the use of TNT in various applications and the future prospects for its development in other fields. We focus on the comprehensive analysis and practical significance of the development of TiO₂ hybrid materials and the need for a better understanding of the structural-chemical properties of anatase TiO₂ nanotubes with metal doping for ion storage devices such as batteries.

Inactivation of SARS-CoV-2 and Other Human Coronaviruses Aided by Photocatalytic One-Dimensional Titania Nanotube Films as a Self-Disinfecting Surface

SARS-CoV-2 and its variants that continue to emerge have necessitated the implementation of effective disinfection strategies. Developing self-disinfecting surfaces can be a potential route for reducing fomite transmissions of infectious viruses. We show the effectiveness of TiO₂ nanotubes (T_NTs) on photocatalytic inactivation of human coronavirus, HCoV-OC43, as well as SARS-CoV-2. T_NTs were synthesized by the anodization process, and their impact on photocatalytic inactivation was evaluated by the detection of residual viral genome copies (quantitative real-time quantitative reverse transcription polymerase chain reaction) and infectious viruses (infectivity assays). T_NTs with different structural morphologies, wall thicknesses, diameters, and lengths were prepared by varying the time and applied potential during anodization. The virucidal efficacy was tested under different UV-C exposure times to understand the photocatalytic reaction's kinetics. We showed that the T_NT presence boosts the inactivation process and demonstrated complete inactivation of SARS-CoV-2 as well as HCoV-OC43 within 30 s of UV-C illumination. The remarkable cyclic stability of these T_NTs was revealed through a reusability experiment. The spectroscopic and electrochemical analyses have been reported to correlate and quantify the effects of the physical features of T_NT with photoactivity. We anticipate that the proposed one-dimensional T_NT will be applicable for studying the surface inactivation of other coronaviruses including SARS-CoV-2 variants due to similarities in their genomic structure.