Advances in antifungal drug measurement by liquid chromatography-mass spectrometry

Multiparametric LC-MS/MS method for simultaneous determination of eleven antifungal drugs and metabolites in human plasma

A multiparametric liquid chromatography-tandem mass spectrometry method has been developed for the simultaneous quantification of 11 antifungal drugs and their metabolites in human plasma. This method addresses the critical need for therapeutic drug monitoring in the treatment of invasive fungal infections, which are increasingly prevalent among immunocompromised patients and those in intensive care units. The method quantifies flucytosin, fluconazole, itraconazole, hydroxy-itraconazole, posaconazole, isavuconazole, voriconazole, voriconazole-N-oxide, anidulafungin, caspofungin, and micafungin. Key challenges in method development included optimising mass spectrometer settings, chromatographic conditions, and sample preparation techniques to ensure accurate, sensitive, and specific detection. Validation of this method was conducted in accordance with the guidelines set by the USA Food and drug administration and the European Medicines Agency covering linearity, precision, accuracy, selectivity, matrix effect, and stability. The method exhibited robust performance with intra- and inter-assay precision under 10 % and average accuracy for intra- and inter-assay comparison of -2.35 % and 0.80 %, respectively. Limits of detection (0.002 to 0.110 mg/L) and a quantification range between 0.005 and 200 mg/L make this method suitable for clinical TDM applications. The ability to simultaneously analyse eleven antifungals and their metabolites within a single 5-minute run enhances its utility in clinical settings, particularly for critically ill patients who may experience significant pharmacokinetic variations. The method requires only 100 µL of plasma, demonstrating good analytical performances rendering it a valuable tool for optimising antifungal therapy and improving patient outcomes in ICU management.

Triazoles in the environment: An update on sample pretreatment and analysis methods

Triazoles, due to their high bactericidal performance, have been widely used in the agricultural, clinical, and chemical industry. However, triazoles have been proven to cause endocrine-toxic and organ impairment in humans as a potentially toxic substance. Besides, because of the improper use and difficulty of degradation, triazoles pesticide residues left in the environment could pose a threat to the environment. Therefore, the rapid, reliable, accurate, and high-sensitivity triazoles analysis methods are significantly essential to effectively monitor their presence in various samples and safeguard human health. This review aims to summarize and update the progress of the pretreatment and analytical methods of triazole fungicides in environmental samples from 2012 to 2024. Common pretreatment methods used to extract and purify targets include simple steps (e.g., protein precipitation and coated blade spray), liquid-liquid extraction, solid-phase extraction, and various microextraction methods such as liquid-phase microextraction and solid-phase microextraction, among others. Detection methods mainly include liquid chromatography-mass spectrometry, gas chromatography-mass spectrometry, supercritical fluid chromatography, sensing methods, and capillary electrophoresis. In addition, we elaborate and compare the advantages and disadvantages of different pretreatment and analytical methods, and their development prospects are discussed.

Comparison of two acquisition modes in mass spectrometry for quantification of 12 antibiotics, including beta-lactams, linezolid, fluoroquinolones and clindamycin: Multiple reactions monitoring (MRM) and fullMS/dd-MS2

The quantification of antibiotics, using mass spectrometry, for monitoring therapeutic drugs is a key benefit in infection management. After an easy work-up of plasma samples, analysis were performed using both two widely used acquisition modes: MRM for the triple quadrupole spectrometer and fullMS/ddMS2 for the HRMS to quantify twelve antibiotics. Comparison between the two acquisition modes were performed. Validation parameters and sample values were used as comparison criteria. The results indicated a good correlation between the two methods, with an advantage for HRMS concerning the matrix effect. Both methods were applied to routine therapeutic drug monitoring.

Divergent mitochondrial responses and metabolic signal pathways secure the azole resistance in Crabtree-positive and negative Candida species

Azole drugs are the main therapeutic drugs for invasive fungal infections. However, azole-resistant strains appear repeatedly in the environment, posing a major threat to human health. Several reports have shown that mitochondria are associated with the virulence of pathogenic fungi. However, there are few studies on the mechanisms of mitochondria-mediated azoles resistance. Here, we first performed mitochondrial proteomic analysis on multiple Candida species (Candida albicans, Nakaseomyces glabrata, Pichia kudriavzevii, and Candida auris) and analyzed the differentially expressed mitochondrial proteins (DEMPs) between azole-sensitive and azole-resistant Candida species. Subsequently, we performed Kyoto Encyclopedia of Genes and Genomes (KEGG) analysis, gene ontology analysis, and protein-protein interaction network analysis of DEMPs. Our results showed that a total of 417, 165, and 25 DEMPs were identified in resistant C. albicans, N. glabrata, and C. auris, respectively. These DEMPs were enriched in ribosomal biogenesis at cytosol and mitochondria, tricarboxylic acid cycle, glycolysis, transporters, ergosterol, and cell wall mannan biosynthesis. The high activations of these cellular activities, found in C. albicans and C. auris (at low scale), were mostly opposite to those observed in two fermenter species-N. glabrata and P. kudriavzevii. Several transcription factors including Rtg3 were highly produced in resistant C. albicans that experienced a complex I activation of mitochondrial electron transport chain (ETC). The reduction of mitochondrial-related activities and complex IV/V of ETC in N. glabrata and P. kudriavzevii was companying with the reduced proteins of Tor1, Hog1, and Snf1/Snf4.IMPORTANCECandida spp. are common organisms that cause a variety of invasive diseases. However, Candida spp. are resistant to azoles, which hinders antifungal therapy. Exploring the drug-resistance mechanism of pathogenic Candida spp. will help improve the prevention and control strategy and discover new targets. Mitochondria, as an important organelle in eukaryotic cells, are closely related to a variety of cellular activities. However, the role of mitochondrial proteins in mediating azole resistance in Candida spp. has not been elucidated. Here, we analyzed the mitochondrial proteins and signaling pathways that mediate azole resistance in Candida spp. to provide ideas and references for solving the problem of azole resistance. Our work may offer new insights into the connection between mitochondria and azoles resistance in pathogenic fungi and highlight the potential clinical value of mitochondrial proteins in the treatment of invasive fungal infections.

Overview of therapeutic drug monitoring and clinical practice

With the rapid development of clinical pharmacy in China, therapeutic drug monitoring (TDM) has become an essential tool for guiding rational clinical drug use and is widely concerned. TDM is a tool that combines pharmacokinetic and pharmacodynamic knowledge to optimize personalized drug therapy, which can improve treatment outcomes, reduce drug-drug toxicity, and avoid the risk of developing drug resistance. To effectively implement TDM, accurate and sophisticated analytical methods are required. By researching the literature published in recent years, we summarize the types of commonly monitored drugs, therapeutic windows, and clinical assays and track the trends and hot spots of therapeutic drug monitoring. The purpose is to provide guidelines for clinical blood drug concentration monitoring, to implement individualized drug delivery programs better, to ensure the rational use of drugs for patients, and to provide a reference for the group to carry out related topics in the future.

Antifungals: From Pharmacokinetics to Clinical Practice

The use of antifungal drugs started in the 1950s with polyenes nystatin, natamycin and amphotericin B-deoxycholate (AmB). Until the present day, AmB has been considered to be a hallmark in the treatment of invasive systemic fungal infections. Nevertheless, the success and the use of AmB were associated with severe adverse effects which stimulated the development of new antifungal drugs such as azoles, pyrimidine antimetabolite, mitotic inhibitors, allylamines and echinochandins. However, all of these drugs presented one or more limitations associated with adverse reactions, administration route and more recently the development of resistance. To worsen this scenario, there has been an increase in fungal infections, especially in invasive systemic fungal infections that are particularly difficult to diagnose and treat. In 2022, the World Health Organization (WHO) published the first fungal priority pathogens list, alerting people to the increased incidence of invasive systemic fungal infections and to the associated risk of mortality/morbidity. The report also emphasized the need to rationally use existing drugs and develop new drugs. In this review, we performed an overview of the history of antifungals and their classification, mechanism of action, pharmacokinetic/pharmacodynamic (PK/PD) characteristics and clinical applications. In parallel, we also addressed the contribution of fungi biology and genetics to the development of resistance to antifungal drugs. Considering that drug effectiveness also depends on the mammalian host, we provide an overview on the roles of therapeutic drug monitoring and pharmacogenomics as means to improve the outcome, prevent/reduce antifungal toxicity and prevent the emergence of antifungal resistance. Finally, we present the new antifungals and their main characteristics.

Excluding interference and detecting Microcystin-LR in the natural lakes and cells based a unique fluorescence method

Cyanobacteria blooms that cause the death of aquatic and terrestrial organisms have attracted considerable attention since the 19th century. The most typical toxin in cyanobacteria blooms is cyanobacteria toxin, particularly microcystin-LR (MC-LR). Therefore, a simple and highly efficient method for detecting MC-LR plays a role in studying the ecological toxicology of MC-LR. However, as MC-LR itself is located in a complex environment, traditional techniques present complex and false-positive defects. To address the above issues, novel technologies should be explored and discovered. Herein, we describe the development of MC-BDKZ as the first paradigm of probes that can concurrently report MC-LR in natural lakes and cells. This novel material shows large Stokes Shift and possesses good photostability and high sensitivity. Considering the properties mentioned above, MC-BDKZ not only achieves the detection of MC-LR in the lake water samples, but also completes the imaging of exogenous MC-LR in cells. Moreover, the interference of many factors in the lake and cells is excluded completely in the process of MC-LR detection. We comprehensively analyzed the response principle and potential application of MC-BDKZ in the process of MC-LR detection. Compared with the conventional MC-LR detection technologies, fluorescence probe technology shows better convenience and greatly reduces distance from the practical application in vitro and in vivo. We envisioned that the development of this visual research tool could provide crucial clues for exploring the pathogenesis of MC-LR in body.

Bio-analytical liquid chromatographic-based method with a mixed mode online solid phase extraction for drug monitoring of fluconazole in human serum

A simple, cost-effective and sensitive liquid chromatography-based bio-analytical method has been developed and validated for therapeutic drug monitoring of fluconazole (FLUC) in human serum. Integration of online mixed-mode solid-phase extraction (SPE) into the analytical system was the key for direct injection of untreated serum samples. A short protein-coated (PC) µBondapak CN silica column (PC-µB-CN-column) as a SPE tool and phosphate buffer saline (PBS) (pH 7.4) as an eluent were applied in the extraction step. PC-µB-CN-column operates in two different chromatographic modes. Using PBS, proteins were extracted from serum samples by size-exclusion liquid chromatography, while FLUC trapping was reversed-phase liquid chromatography dependent. FLUC was then eluted from the PC-µB-CN-column onto the quantification position using a mixture of acetonitrile-distilled deionized water (20:80, v/v) as an eluent and ODS analytical column. FLUC was separated at ambient temperature (22 ± 1 °C) and detected at 260 nm. The method was linear over the range of 200-10000 ng/mL. FLUC recovery in untreated serum samples ranged from 97.8 to 98.8% and showed good accuracy and precision. The reliability of the developed method was evaluated by studying the pharmacokinetic profile of FLUC in humans after an oral administration of a single 150 mg tablet.

Quantification of 15 Antibiotics Widely Used in the Critical Care Unit with a LC-MS/MS System: An Easy Method to Perform a Daily Therapeutic Drug Monitoring

Potential under- or overdose of antibiotics may occur in intensive care units due to high variability in plasma concentrations. The risk is either treatment failure or toxicity. Thus, therapeutic drug monitoring of antibiotics may guide dosing adjustment, maximising antibacterial efficacy and minimising toxicity. The aim of this study was to develop and validate a method for the analysis of 15 antibiotics including beta-lactams, linezolid, fluoroquinolones, daptomycin, and clindamycin to have a complete panel in the management of infections. We proposed to develop a fast, sensitive, and quantitative method for the analysis of 15 antibiotics using ultra-performance liquid chromatography coupled with triple quadrupole mass spectrometer (UPLC-MS/MS) technology. this method required only 100 µL of plasma and consisted of a rapid liquid-liquid deproteinisation using methanol. Calibration curves ranged from 0.078 to 500 mg/L depending on the molecules, and were defined according to a therapeutic range. Inter- and intra-assay precisions values were less than 15%. This work described the development and the full validation of a precise, sensitive and accurate assay using UPLC-MS/MS technology. After validation, this new assay was successfully applied to routine therapeutic drug monitoring.

Natural Compounds With Antimicrobial and Antiviral Effect and Nanocarriers Used for Their Transportation

Due to the increasing prevalence of life-threatening bacterial, fungal and viral infections and the ability of these human pathogens to develop resistance to current treatment strategies, there is a great need to find and develop new compunds to combat them. These molecules must have low toxicity, specific activity and high bioavailability. The most suitable compounds for this task are usually derived from natural sources (animal, plant or even microbial). In this review article, the latest and most promising natural compounds used to combat bacteria, filamentous fungi and viruses are presented and evaluated. These include plant extracts, essential oils, small antimicrobial peptides of animal origin, bacteriocins and various groups of plant compounds (triterpenoids; alkaloids; phenols; flavonoids) with antimicrobial and antiviral activity. Data are presented on the inhibitory activity of each natural antimicrobial substance and on the putative mechanism of action against bacterial and fungal strains. The results show that among the bioactive compounds studied, triterpenoids have significant inhibitory activity against coronaviruses, but flavonoids have also been shown to inhibit SARS-COV-2. The last chapter is devoted to nanocarriers used to improve stability, bioavailability, cellular uptake/internalization, pharmacokinetic profile and reduce toxicity of natural compunds. There are a number of nanocarriers such as liposomes, drug delivery microemulsion systems, nanocapsules, solid lipid nanoparticles, polymeric micelles, dendrimers, etc. However, some of the recent studies have focused on the incorporation of natural substances with antimicrobial/antiviral activity into polymeric nanoparticles, niosomes and silver nanoparticles (which have been shown to have intrinsic antimicrobial activity). The natural antimicrobials isolated from animals and microorganisms have been shown to have good inhibitory effect on a range of pathogens, however the plants remain the most prolific source. Even if the majority of the studies for the biological activity evaluation are in silico or in vitro, their internalization in the optimum nanocarriers represents the future of “green therapeutics” as shown by some of the recent work in the field.

Analytical Methods for Determination of Antiviral Drugs in Different Matrices: Recent Advances and Trends

Viruses are the main pathogenic substances that cause severe diseases in humans and other living things. They are among the most common microorganisms, and consequently, antiviral drugs have emerged to prevent and treat viral infections. Antiviral drugs are an essential drug group considering their prescription and consumption rates for different diseases and indications. Therefore, it is crucial to develop accurate and precise analytical methods to detect antiviral drugs in various matrices. Chromatographic techniques are used frequently for the quantification purpose since they allow simultaneous determination of antivirals. Electrochemical methods have also gained importance since the analysis can be performed quickly without the need for pretreatment. Spectrophotometric and spectrofluorimetric methods are used because they are simple, inexpensive, and less time-consuming methods. The purpose of this review is to present an overview of the analysis of currently used antiviral drugs from 2010 to 2021. Since studies on antiviral drugs are numerous, selected publications were reviewed in this article. The analysis of antiviral drugs was divided into three main groups: chromatographic, spectrometric, and electrochemical methods which were applied to different matrices, including pharmaceutical, biological, and environmental samples.

Rapid and Simple Reversed-Phase High-Performance Liquid Chromatography (RP-HPLC) Method for Simultaneous Quantifications of Triazole Antifungals in Human Serum

PURPOSE

To develop and validate a one-step, rapid and simple reversed-phase high-performance liquid chromatography (HPLC)-based protocol for the simultaneous measurement of voriconazole (VCZ), posaconazole (POSA), itraconazole (ITC) in serum/plasma.

METHODS

Calibration standards (CS) and quality control samples were prepared in drug-free serum by spiking with the triazoles at different concentrations. HPLC was performed with C₁₈ column, isocratic mobile phase after extraction with cold acetonitrile. The standardized method was tested in 2693 patients' serum/plasma samples.

RESULTS

Linearity of CS for ITC, VCZ and POSA was proportional to the nominal concentration (correlation coefficient > 0.999). Limit of detection (mg/L) for ITC, VCZ and POSA was 0.25, 0.25 and 0.125, respectively. The lower limit of quantification (mg/L) for ITC, VCZ and POSA was 0.5, 0.5 and 0.25, respectively. Precision and accuracy were in acceptable range with 100% average percentage recovery. No interferences from endogenous substances and other antimicrobial compounds were noted. In clinical samples, the therapeutic range achieved for VCZ was 39.9%. Whereas, 61.1% and 44% of samples with ITC and POSA, respectively, were in the sub-therapeutic range.

CONCLUSION

We developed a rapid and simple HPLC method to quantify common triazoles in a single chromatographic run allowing simultaneous measurement of different antifungals in a small volume of serum/plasma. Thus, therapeutic drug monitoring requests can be processed in one run without changing the protocol parameters, column or column conditioning thereby improving turnaround time.

Review of Chromatographic Methods Coupled with Modern Detection Techniques Applied in the Therapeutic Drugs Monitoring (TDM)

Therapeutic drug monitoring (TDM) is a tool used to integrate pharmacokinetic and pharmacodynamics knowledge to optimize and personalize various drug therapies. The optimization of drug dosing may improve treatment outcomes, reduce toxicity, and reduce the risk of developing drug resistance. To adequately implement TDM, accurate and precise analytical procedures are required. In clinical practice, blood is the most commonly used matrix for TDM; however, less invasive samples, such as dried blood spots or non-invasive saliva samples, are increasingly being used. The choice of sample preparation method, type of column packing, mobile phase composition, and detection method is important to ensure accurate drug measurement and to avoid interference from matrix effects and drug metabolites. Most of the reported procedures used liquid chromatography coupled with tandem mass spectrometry (LC-MS/MS) techniques due to its high selectivity and sensitivity. High-performance chromatography with ultraviolet detection (HPLC-UV) methods are also used when a simpler and more cost-effective methodology is desired for clinical monitoring. The application of high-performance chromatography with fluorescence detection (HPLC-FLD) with and without derivatization processes and high-performance chromatography with electrochemical detection (HPLC-ED) techniques for the analysis of various drugs in biological samples for TDM have been described less often. Before chromatographic analysis, samples were pretreated by various procedures-most often by protein precipitation, liquid-liquid extraction, and solid-phase extraction, rarely by microextraction by packed sorbent, dispersive liquid-liquid microextraction. The aim of this article is to review the recent literature (2010-2020) regarding the use of liquid chromatography with various detection techniques for TDM.

Therapeutic Drug Monitoring Is a Feasible Tool to Personalize Drug Administration in Neonates Using New Techniques: An Overview on the Pharmacokinetics and Pharmacodynamics in Neonatal Age

Therapeutic drug monitoring (TDM) should be adopted in all neonatal intensive care units (NICUs), where the most preterm and fragile babies are hospitalized and treated with many drugs, considering that organs and metabolic pathways undergo deep and progressive maturation processes after birth. Different developmental changes are involved in interindividual variability in response to drugs. A crucial point of TDM is the choice of the bioanalytical method and of the sample to use. TDM in neonates is primarily used for antibiotics, antifungals, and antiepileptic drugs in clinical practice. TDM appears to be particularly promising in specific populations: neonates who undergo therapeutic hypothermia or extracorporeal life support, preterm infants, infants who need a tailored dose of anticancer drugs. This review provides an overview of the latest advances in this field, showing options for a personalized therapy in newborns and infants.

Antifungal therapeutic drug monitoring: focus on drugs without a clear recommendation

BACKGROUND

The goal of therapeutic drug monitoring (TDM) is to determine the appropriate exposure of difficult-to-manage medications to optimize the clinical outcomes in patients in various clinical situations. Concerning antifungal treatment, and knowing that this procedure is expensive and time-consuming, TDM is particularly recommended for certain systemic antifungals: i.e., agents with a well-defined exposure-response relationship and unpredictable pharmacokinetic profile or narrow therapeutic index. Little evidence supports the routine use of TDM for polyenes (amphotericin B), echinocandins, fluconazole or new azoles such as isavuconazole, despite the fact that a better understanding of antifungal exposure may lead to a better response.

AIMS

The aim of this work is to review published pharmacokinetic/pharmacodynamic data on systemically administered antifungals, focusing on those for which monitoring is not routinely recommended by experts.

SOURCES

A MEDLINE search of the literature in English was performed introducing the following search terms: amphotericin B, fluconazole, itraconazole, voriconazole, posaconazole, triazoles, caspofungin, micafungin, anidulafungin, echinocandins, pharmacokinetics, pharmacodynamics, and therapeutic drug monitoring. Review articles and guidelines were also screened.

CONTENT

This review collects different pharmacokinetic/pharmacodynamic aspects of systemic antifungals and summarizes recent threshold values for clinical outcomes and adverse events. Although for polyenes, echinocandins, fluconazole and isavuconazole extensive clinical validation is still required for a clear threshold and a routine monitoring recommendation, particular points such as liposome structure or complex pathophysiological conditions affecting final exposure are discussed. For the rest, their better-defined exposure-response/toxicity relationships allow access to useful threshold values and to justify routine monitoring. Additionally, clinical data are needed to better define thresholds that can minimize the development of antifungal resistance.

IMPLICATIONS

General TDM for all systemic antifungals is not recommended; however, this approach may help to establish an adequate antifungal exposure for a favourable response, prevention of toxicity or development of resistance in special clinical circumstances.