Sunlight photocatalytic degradation of ofloxacin using UiO-66/wood composite photocatalysts

Efficient Photocatalytic Degradation of Highly Concentrated Perfluorooctanoic Acid by Bi Self-Doped Bi2MoO6

Bi self-doped Bi2MoO6 was synthesized by a solvothermal method. The introduction of Bi enhanced the absorption of visible light by the catalyst, and the Bi could act as an electron transfer site to facilitate the separation of photogenerated carriers and enhance the photocatalytic activity of the catalyst for the degradation of PFOA. The oxidation of PFOA by ·O2- as the main reactive oxygen species of degradation facilitated its degradation. Under full spectrum illumination for 40 min, the degradation rate of PFOA (100 mg/L) by Bi3MoO6 reached 88.1%, which is 3 times that of the original Bi2MoO6. The degradation amount reached 88.1 mg·gcat-1, and the degradation rate was 2.20 mg·gcat-1·min-1. This work provides new ideas for the modification of catalysts.

Fabrication of S-scheme heterojunction consisting of W-doped BiVO4 and biperovskite Cs2AgBiBr6 for photocatalytic degradation of antibiotics

Photocatalysis technology can degrade organic pollutants in wastewater, improving the ecological environment and protecting biodiversity. The BiVO4 stable chemical properties of BiVO4 make it a robust candidate for photochemical applications. Moreover, its broad light absorption spectrum and optimal band structure further enhance its potential, driving widespread research interest. The introduction of the eco-friendly biperovskite Cs2AgBiBr6 enhanced BiVO4's surface area and visible light absorbance. Simultaneously, the doping process introduces impurities that modify charge transfer pathways, thereby enhancing the separation efficiency of photogenerated electron-hole pairs. When contrasted with pure BiVO4, the W-BiVO4/Cs2AgBiBr6 composite demonstrates superior surface area characteristics and exhibits stronger absorption within the visible light spectrum. Within 40 min after exposure to visible light, the efficiency of W-BiVO4/Cs2AgBiBr6 photocatalyst to degrade ofloxacin (OFX) and meloxicam (MEL) was 93.15 % and 92.70 %, respectively. Based on the toxicity analyses and antimicrobial assays simulated by the software, no highly toxic substances were found in the degradation intermediate products of OFX and MEL. The catalysts' energy band structure and photoelectrochemical properties showed that W-BiVO4/Cs2AgBiBr6 followed the S-scheme heterojunction charge transfer mechanism. By integrating BiVO4 with other semiconductors in the form of S-scheme heterojunctions, this study explores a strategy that may effectively improve photocatalytic efficiency, particularly in pollutant degradation applications.

Synergistic photocatalysis for bacteria inactivation and organic pollutant removal by S-scheme heterojunction InVO4/Bi5O7I: Performance evaluation and mechanism investigation

The low efficiency of charge carrier separation is a major limitation hindering the application of photocatalytic technology. Constructing S-scheme heterojunction photocatalysts not only effectively promotes the separation of charge carriers, but also maximizes the oxidative and reductive capabilities of the two monomers. In this study S-scheme heterogeneous InVO4/Bi5O7I photocatalyst was synthesized by hydrothermal method combined with calcination. The optimal sample 20 % InVO4/Bi5O7I can completely deactivate Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli) in 30 min, remove 20 mg/L TC 76.0 % in 60 min and 20 mg/L BPA 93.0 % in 90 min. Intermediate products of TC and BPA degradation were detected using LC-MS, and possible degradation pathways were proposed. The photocurrent and electrochemical impedance spectroscopy (EIS) tests confirm that InVO4/Bi5O7I exhibits excellent photocurrent intensity and photocarrier migration ability, which are crucial reasons for the enhancement of the photocatalytic performance of the InVO4/Bi5O7I composite. Capture experiments indicate that OH, O2-, h+ and e-are reactive species. EPR further confirms the generation of OH and O2-. Combined with Kelvin probe force microscopy (KPFM) and band structure analysis, it is proposed that InVO4/Bi5O7I has an S-scheme charge transfer mechanism.

Advanced BiVO4-deoxygenated lignocellulosic photocatalyst for effective degradation of organic and heavy metal pollutants in aqueous system

Bismuth vanadate (BiVO4) is a common photocatalyst for water remediation, yet its powder form renders difficult to disperse, recycle, and regenerate, limiting photodegradation efficiency. In this study, a lignocellulosic-templated BiVO4 photocatalyst was fabricated from BiVO4 precursor and lignocellulose using a simple vacuum impregnation (w/o heat treatment on wood template). Results showed that the modified template retained original hierarchical structure with an increased specific surface area and reduced hemicellulose content, leading to a promising template for uniform distribution of BiVO4. Moreover, compared to untreated, heat treatment cleaved acetyl groups in the hemicellulose chain, broke down fatty ether bonds, and oxidized lignin side chains, resulting in no disruption to the catalysis of BiVO4. The BiVO4-pyrolyzed lignocellulosic photocatalyst achieved remarkable degradation efficiencies of 90.03 % (approximately 7-fold increase compared to untreated) for RhB and complete degradation of Cr (VI) within 60 min. Furthermore, the efficiency remained >80 % after seven cycles. The mechanism was hypothesized that BiVO4 and template play distinct roles, as deoxygenated lignocellulosic template only acts as a carrier for BiVO4 growth, and BiVO4 serves as the photocatalyst. However, untreated template can react with BiVO4 and impair photocatalytic efficiency. The BiVO4-pyrolyzed lignocellulosic photocatalyst holds great promise for the remediation of aqueous contaminants.

Synergistic enantioseparation system based on a novel nanomaterial synthesized by chiral metal-organic framework and chiral molecularly imprinted polymer in capillary electrochromatography

A capillary electrochromatography (CEC) synergistic enantioseparation system based on a novel nanomaterial synthesized by chiral molecularly imprinted polymers (CMIPs) and chiral metal organic frameworks (CMOFs) was developed. Compared with CMIPs and CMOFs alone, the enantioseparation performance of ofloxacin (OFL) of the CEC with the novel nanomaterial as stationary phases was greatly improved. CMOFs with chiral recognition ability have synergize with CMIPs to greatly improve the chiral selectivity of the novel stationary phases in CEC. As a proof-of-concept demonstration, a coated capillary column was prepared by a sol-gel method using S-OFL (template), iron-based cyclodextrin MOF (Fe-CD-MOF, a CMOF), 3-aminopropyltriethoxysilane (functional monomer), and tetraethyl orthosilicate (cross-linking agent). Then, the newly constructed CEC system has excellent enantioseparation performance of OFL with a resolution of 3.92. Finally, computerized molecular docking revealed that the difference in the binding ability of Fe-CD-MOF to ofloxacin enantiomers was an important mechanism for CEC chiral separation. This innovative development of synergistic chiral stationary phases based on CMOFs and CMIPs creates a highly efficient potential direction for enantiomer separation.

Light-driven photocatalysis as an effective tool for degradation of antibiotics

Antibiotic contamination has become a severe issue and a dangerous concern to the environment because of large release of antibiotic effluent into terrestrial and aquatic ecosystems. To try and solve these issues, a plethora of research on antibiotic withdrawal has been carried out. Recently photocatalysis has received tremendous attention due to its ability to remove antibiotics from aqueous solutions in a cost-effective and environmentally friendly manner with few drawbacks compared to traditional photocatalysts. Considerable attention has been focused on developing advanced visible light-driven photocatalysts in order to address these problems. This review provides an overview of recent developments in the field of photocatalytic degradation of antibiotics, including the doping of metals and non-metals into ultraviolet light-driven photocatalysts, the formation of new semiconductor photocatalysts, the advancement of heterojunction photocatalysts, and the building of surface plasmon resonance-enhanced photocatalytic systems.

A Wooden Carbon-Based Photocatalyst for Water Treatment

Due to a large number of harmful chemicals flowing into the water source in production and life, the water quality deteriorates, and the use value of water is reduced or lost. Biochar has a strong physical adsorption effect, but it can only separate pollutants from water and cannot eliminate pollutants fundamentally. Photocatalytic degradation technology using photocatalysts uses chemical methods to degrade or mineralize organic pollutants, but it is difficult to recover and reuse. Woody biomass has the advantages of huge reserves, convenient access and a low price. Processing woody biomass into biochar and then combining it with photocatalysts has played a complementary role. In this paper, the shortcomings of a photocatalyst and biochar in water treatment are introduced, respectively, and the advantages of a woody biochar-based photocatalyst made by combining them are summarized. The preparation and assembly methods of the woody biochar-based photocatalyst starting from the preparation of biochar are listed, and the water treatment efficiency of the woody biochar-based photocatalyst using different photocatalysts is listed. Finally, the future development of the woody biochar-based photocatalyst is summarized and prospected.

Enhanced degradation and removal of ciprofloxacin and ofloxacin through advanced oxidation and adsorption processes using environmentally friendly modified carbon nanotubes

This study explores the utilization of adsorption and advanced oxidation processes for the degradation of ofloxacin (OFL) and ciprofloxacin (CIP) using a green functionalized carbon nanotube (MWCNT-OH/COOH-E) as adsorbent and catalyst material. The stability and catalytic activity of the solid material were proved by FT-IR and TG/DTG, which also helped to elucidate the reaction mechanisms. In adsorption kinetic studies, both antibiotics showed similar behavior, with an equilibrium at 30 min and 60% removal. The adsorption kinetic data of both antibiotics were well described by the pseudo-first-order (PFO) model. Different advanced oxidation processes (AOPs) were used, and the photolytic degradation was not satisfactory, whereas heterogeneous photocatalysis showed high degradation (⁓ 70%), both processes with 30 min of reaction. Nevertheless, ozonation and catalytic ozonation have resulted in the highest efficiencies, 90%, and 70%, respectively, after 30-min reaction. For AOP data modeling, the first-order model better described CIP and OFL in photocatalytic and ozonation process. Intermediates were detected by MS-MS analysis, such as P313, P330, and P277 for ciprofloxacin and P391 and P332 for ofloxacin. The toxicity test demonstrated that a lower acute toxicity was observed for the photocatalysis method samples, with only 3.1 and 1.5 TU for CIP and OFL, respectively, thus being a promising method for its degradation, due to its lower risk of inducing the proliferation of bacterial resistance in an aquatic environment. Ultimately, the analysis of MWCNT reusability showed good performance for 2 cycles and regeneration of MWCNT with ozone confirmed its effectiveness up to 3 cycles.

Bio-based matrix photocatalysts for photodegradation of antibiotics

Antibiotics development during the last century permitted unprecedent medical advances. However, it is undeniable that there has been an abuse and misuse of antimicrobials in medicine and cosmetics, food production and food processing, in the last decades. The pay toll for human development and consumism is the emergence of extended antimicrobial resistance and omnipresent contamination of the biosphere. The One Health concept recognizes the interconnection of human, environmental and animal health, being impossible alter one without affecting the others. In this context, antibiotic decontamination from water-sources is of upmost importance, with new and more efficient strategies needed. In this framework, light-driven antibiotic degradation has gained interest in the last few years, strongly relying in semiconductor photocatalysts. To improve the semiconductor properties (i.e., efficiency, recovery, bandgap width, dispersibility, wavelength excitation, etc.), bio-based supporting material as photocatalysts matrices have been thoroughly studied, exploring synergetic effects as operating parameters that could improve the photodegradation of antibiotics. The present work describes some of the most relevant advances of the last 5 years on photodegradation of antibiotics and other antimicrobial molecules. It presents the conjugation of semiconductor photocatalysts to different organic scaffolds (biochar and biopolymers), then to describe hybrid systems based on g-C3N4 and finally addressing the emerging use of organic photocatalysts. These systems were developed for the degradation of several antibiotics and antimicrobials, and tested under different conditions, which are analyzed and thoroughly discussed along the work.

Advances in surface properties characterization and modification for lignin

Renewed interests on lignin and its derivatives have led to increasingly more investigations due to the problems in environmental impact while with the great reuse possibilities for producing them-based new and advanced materials to reduce the petroleum achieving sustainable development. The related studies have shown more integrated database on the surface properties characterization and modification of those renewable materials. Based on numerous works did at our group and others reported elsewhere, this review covers the surface properties of lignin and its derivatives in relation to various methods and theories. In this work, the progress on the recent developments of advanced methods for lignin surface characterization and modification are also documented. Of this review, a perspective is finally presented.

Construction of graphene quantum dots ratiometric fluorescent probe by intermolecular electron transfer effect for intelligent and real-time visual detection of ofloxacin and its L-isomer in daily drink

The design of intelligent and real-time sensing devices is significant in the medical drug monitoring field, but it is still highly challenging. Here, ratiometric fluorescent detections of ofloxacin (OFL) and its L-isomer levofloxacin (LEV) constructed from tri-doped graphene quantum dots (T-GQDs) are reported, and the detection limits reach as low as 46/67 nM toward OFL/LEV due to the intermolecular electron transfer (intermolecular ET) effect. After adding OFL/LEV, the generation of electrostatic bond provides a channel for the intermolecular ET from the edge of T-GQDs to OFL/LEV, resulting in the fluorescence quenching at 414 nm and the fluorescence promoting at 498 nm. Furthermore, a smartphone can be used for the visual and quantitative detection of OFL and LEV by identifying the RGB values of test paper and drink samples. This work not only reveals the physics mechanism of ratiometric detection, but also develops a convenient smartphone diagnostic for OFL and LEV.

Highly efficient degradation of ofloxacin and diclofenac by composite photocatalyst aloe-emodin/PMMA

Photocatalysis is one of the most effective methods to remove pollutants from water. Photocatalyst is the core of photocatalysis. The composite photocatalyst combines the photosensitizer with the support and uses the photosensitivity of the photosensitizer and the stability and adsorption of the support to achieve efficient and rapid degradation of pharmaceuticals in water. In this study, natural aloe-emodin with π-conjugated structure was used as photosensitizer to react with macroporous resin polymethylmethacrylate (PMMA) under mild conditions to prepare composite photocatalysts AE/PMMAs. The photocatalyst underwent photogenerated electron migration under visible light to form ^•O₂^- and holes with high oxidation activity, which could realize efficient photocatalytic degradation of ofloxacin and diclofenac sodium and showed excellent stability, recyclability and industrial feasibility. This research has developed an efficient method of composite photocatalyst and realized the application of a natural photosensitizer in pharmaceutical degradations.

A novel Zn/Eu-MOF for the highly sensitive, reversible and visualized sensing of ofloxacin residues in pork, beef and fish

The study investigates a bimetallic organic framework (Zn/Eu-MOF) based fluorescent probe for visual detection of ofloxacin (OFL) in pork, beef and fish. The developed sensing probe recognizes OFL through internal filtration and cation-π interaction between OFL and Zn/Eu-MOF, resulting in a distinct color change from orange-red to light green. The content of OFL can be determined through RGB analysis by a mobile-phone. The developed sensing probe offers several advantages such as broad linear range (0.1 ∼ 80 μM), rapid response time (30 s), low detection line (0.44 μM). The effectiveness of the sensing probe can last for five rounds with good recovery. Moreover, the application of the sensing probe on pork, beef and fish samples are reliable, with recoveries ranging from 93.4 to 112.1%, and the relative standard deviations (RSD) within 1.17% to 2.06%. These results suggest that the developed sensing probe could have significant potential for practical on-site test in food.

In-situ construction of Zr-based metal-organic framework core-shell heterostructure for photocatalytic degradation of organic pollutants

Photocatalysis is an eco-friendly promising approach to the degradation of textile dyes. The majority of reported studies involved remediation of dyes with an initial concentration ≤50 mg/L, which was away from the existing values in textile wastewater. Herein, a simple solvothermal route was utilized to synthesize CoFe2O4@UiO-66 core-shell heterojunction photocatalyst for the first time. The photocatalytic performance of the as-synthesized catalysts was assessed through the photodegradation of methylene blue (MB) and methyl orange (MO) dyes at an initial concentration (100 mg/L). Under simulated solar irradiation, improved photocatalytic performance was accomplished by as-obtained CoFe2O4@UiO-66 heterojunction compared to bare UiO-66 and CoFe2O4. The overall removal efficiency of dyes (100 mg/L) over CoFe2O4@UiO-66 (50 mg/L) reached >60% within 180 min. The optical and photoelectrochemical measurements showed an enhanced visible light absorption capacity as well as effective interfacial charge separation and transfer over CoFe2O4@UiO-66, emphasizing the successful construction of heterojunction. The degradation mechanism was further explored, which revealed the contribution of holes (h+), superoxide (•O2 -), and hydroxyl (•OH) radicals in the degradation process, however, h+ were the predominant reactive species. This work might open up new insights for designing MOF-based core-shell heterostructured photocatalysts for the remediation of industrial organic pollutants.

Preparation and photocatalytic performance of UIO-66/La-MOF composite

To improve the photocatalytic degradation efficiency of photocatalytic materials UIO-66 and La-MOFs under visible-light irradiation, a series of photocatalytic materials with La and Zr as metal centers and terephthalic acid (H₂BDC) and 2-amino terephthalic acid (H₂ATA) as organic ligands were prepared by solvothermal method. The photocatalytic materials were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), UV-visible (UV-vis) spectroscopy, Fourier transform infrared (FT-IR) spectroscopy, and Mott-Schottky test. The photocatalytic degradation performance to Rhodamine B of the catalysts was fully investigated. Results show that the H₂ATA series had stronger visible-light absorption capacity and better photocatalytic performance. The 0.35 La/Zr-H₂ATA composite showed the best photocatalytic degradation. The quenching experiments confirmed that the active species in the photocatalytic degradation were the holes and superoxide radicals. The possible mechanisms of the carrier migration paths in the energy level matching for La/Zr-H₂BDC and La/Zr-H₂ATA were also discussed in detail.

Facile fabrication of electrospun g-C3N4/Bi12O17Cl2/poly(acrylonitrile-co-maleic acid) heterojunction nanofibers for boosting visible-light catalytic ofloxacin degradation

Electrospun g-C3N4/Bi12O17Cl2/poly(acrylonitrile-co-maleic acid) nanofibers were fabricated and applied for highly efficient removal of ofloxacin.