Results from a round robin test for the ecotoxicological evaluation of construction products using two leaching tests and an aquatic test battery

Eco-toxicity assessment of industrial by-product-based alkali-activated binders using the sea urchin embryogenesis bioassay

New cement-based materials such as alkali-activated binders (AABs) or geopolymers allow the incorporation of waste or industrial by-products in their formulation, resulting an interesting valorization technique. Therefore, it is essential to inquire about the potential environmental and health impacts throughout their life cycle. In the European context, a minimum aquatic toxicity tests battery has been recommended for construction products, but their potential biological effects on marine ecosystems have not been considered. In this study, three industrial by-products, PAVAL® (PV) aluminum oxide, weathered bottom ash (WBA) resulting from incinerator bottom ash and glass cullet recycling waste (CSP), were evaluated as precursors in the AAB formulation from an environmental point of view. To determine the potential effects on marine environment caused by the leaching of contaminants from these materials into seawater, the leaching test EN-12457-2 and an ecotoxicity test using the model organism sea urchin Paracentrotus lividus were conducted. The percentage of abnormal larval development was selected as endpoint of the toxicity test. Based on the results obtained from the toxicity tests, AABs have less damaging impact (EC₅₀ values: 49.2%-51.9%) on the marine environment in general than raw materials. The results highlight the need to stablish a specific battery of toxicity tests for the environmental assessment of construction products on marine ecosystem.

Assessment of the environmental acceptability of potential artificial reef materials using two ecotoxicity tests: Luminescent bacteria and sea urchin embryogenesis

Ecotoxicological analysis of construction products is a relatively unexplored area at international level. Aquatic toxicity tests on construction products has been recommended recently for freshwater environment. However, the biological effects of alternative materials on marine ecosystem are still not considered. In this study, the main aim was to assess the environmental impact of alternative mortars proposed as artificial reefs (ARs) materials. The ARs specimens were developed by 3D printing, based on cement and geopolymer mortars using recycled sands of glass and seashells. For this purpose, a leaching test and two different toxicity bioassays, luminosity reduction of marine bacteria Vibrio fischeri (Microtox®) and the success of embryo-larval development of sea-urchin Paracentrotus lividus, were conducted. From the leaching results it should be noted that the mobility of all trace elements considered in both, raw materials and mortars, meet the inert landfill limits, except As, Mo, Se or Sb in the leachates geopolymer mortars. However, the results obtained from the both bioassays show low environmental acceptability for those mortars containing shell sand, probably due to the degradation of the organic matter adhered to the shells. On the other hand, cement mortars obtain better results than geopolymer mortars, regardless of the aggregate used, showing certain consistency with the leaching behaviour, since they present the lowest mobility of trace chemical elements. Therefore, the results supporting the environmental acceptability of its potential use as alternative materials in the production of ARs.

Ecotoxic emissions generated by illegal burning of household waste

The practice of burning household waste including different types of plastic is illegal in Hungary, still an existing problem. As environmental consequences are hardly known, this study attempts to give an initial estimation of the ecotoxicity generated during controlled combustion of different waste types. These samples included polystyrene (PS), polyethylene (PE), polypropylene (PP), polyvinyl chloride (PVC), polyurethane (PU), oriented strand board (OSB) and rag (RAG). Ecotoxicological profiling was completed using the following test battery: Vibrio fischeri bioluminescence inhibition assay, Daphnia magna immobility test and the seedling emergence assay. Also, genotoxicity of plastic waste samples was assessed using the SOS Chromotest. Concerning main pollutants in the samples, the samples could be distinguished as 'PAH-type' and 'heavy metal-type' samples. PVC, PU and PS samples showed the highest toxicity in the Vibrio and Daphnia assays. The PVC sample was characterized by an extremely high cadmium concentration (22.4 μg/L), PS, PP and PU samples on the contrary had high total PAH content. While Vibrio and Daphnia showed comparable sensitivity, the phytotoxicity assay had no response for any of the samples tested. Samples originating from the controlled burning of different plastic types such as PU, PVC, PS and PP were classified as genotoxic, PS sample showed extremely high genotoxicity. Genotoxicity expressed as SOSIF showed strong correlation with most of the PAHs detected.

Testing of Eluates from Waterproof Building Materials for Potential Environmental Effects Due to the Behavior of Enchytraeus albidus

In order to determine the potential environmental impact of construction products, it is necessary to evaluate their influence on organisms exposed to them or their eluates under environmental conditions. The behavior of the white worm Enchytraeus albidus is a useful tool for assessing the potential environmental impact of construction products in contact with water and soil. This study investigates the environmental effects of eluates from two construction products, a reactive waterproofing product, and an injection resin, on the reproduction and avoidance behavior of E. albidus. The eluates were prepared according to existing guidelines. The soil used for the tests was moistened with the eluates of the construction products. The reproduction results of the worms were collected after six weeks of exposure. Offsprings were counted under the microscope and statistically analyzed. Results from the avoidance behavior were collected after 48 h of exposure, and results were compared with the reproduction results. The eluates from both construction products induced significant changes in the reproduction behavior of E. albidus. Undiluted or only slightly diluted eluates of the injection resin drastically reduced the reproduction of the worms, whereas the leaches of the reactive waterproofing product only had a minor effect. The avoidance results for the injection resin indicates that its presence in the habitat is clearly detrimental to the survival of E. albidus, while the avoidance results for the waterproofing resin showed an initial avoidance of the eluates, but no harmful effects were observed. The avoidance test is a way of rapid toxicity screening of environmental samples when time is a critical parameter to measure possible environmental effects. This study shows that ecotoxicological tests using Enchytraeids are a valuable and important tool for understanding the mode of action of eluates from construction products in the environment.

Ecotoxicological characterization of emissions from steel coatings in contact with water

In order to prevent corrosion damage, steel structures need to be protected. Coating systems achieve this by the isolation of the steel from its environment. Common binding agents are epoxide and polyurethane resins which harden by polyaddition reactions. In contact with water, various organic substances might be leached out and released into the aquatic environment potentially causing adverse effects. So far, no legal requirements are mandatory for the environmental sustainability of coating systems. To characterize emissions from steel coatings, recommendations for the ecotoxicological assessment of construction products were utilized. Seven different coating systems based on epoxide or polyurethane resins were leached in 8 steps (6 h-64 d), followed by the testing of acute toxic effects on bacteria and algae as well as estrogen-like and mutagenic effects. In addition, chemical analysis by GC-MS was performed to identify potentially toxic compounds released from the coating systems. Two systems tested did not show any significant effects in the bioassays. One coating system caused significant algal toxicity, none was found to cause mutagenic effects. The other coating systems mainly showed estrogenic effects and bacterial toxicity. The effects increased with increasing leaching time. 4-tert-butylphenol, which is used in epoxy resins as a hardener, was identified as the main contributor to acute and estrogenic effects in two coatings. The release mechanism of 4-tert-butylphenol was characterized by two different modelling approaches. It was found that the release from the most toxic coating is not explainable by an elevated content of 4-tert-butylphenol but more likely by the release mechanism that - in contrast to the less toxic coating - is controlled not only by diffusion. This finding might indicate a sub-optimal formulation of this coating system resulting in a less stable layer and thus an increased release of toxic compounds.

Assessment of leachates from reactive fire-retardant coatings by chemical analysis and ecotoxicity testing

The environmental compatibility of reactive fire-retardant coatings (intumescent paints) was investigated by a combination of leaching and ecotoxicological tests. Three representative fire-retardant coating systems were tested using two leaching procedures: "Horizontal Dynamic Surface Leaching Test" (DSLT) and the "Intermittent Immersion Test" (IIT). All eluate fractions (8 for DSLT and 9 for IIT) were analyzed for pH, conductivity, concentration of total organic carbon and selected anions und cations. Additionally, a GC-MS screening of selected fractions was conducted for identification of organic compounds. Eluate fractions 1 + 2 and fraction 7 of the DSLT were analyzed in four ecotoxicological tests (algae, daphnia, fish egg, luminescent bacteria) and in one genotoxicity test (umu). Concentration of most analytes was rather low or below limit of detection for many eluates. Analytes detected in eluates of all three products are Zn, Ba, SO₄^2- and PO₄^3-. Release patterns do not indicate a general trend: some compounds show maximum release in the first fractions while for others the maximum was observed in later test stages. Ecotoxic effects in eluates were found, which were higher in the eluate fraction 7 (maximum lowest ineffective dilution for luminescent bacteria (LID_L) 256) than in the eluate fraction 1 + 2 (maximum LID_L = 24). The sensitivity of the test systems was very different with highest effects for luminescent bacteria, followed by algae and daphnia and without effects in the fish egg test and umu test. A biotest battery for the comprehensive assessment is therefore advisable.

Ecotoxicological Assessment of Immersion Samples from Facade Render Containing Free or Encapsulated Biocides

To protect house facades from fouling by microorganisms, biocides can be added to a render or paint before it is applied. During driving rain events, these biocides gradually leach out and have the potential to pollute soil or aquatic ecosystems. We studied the leaching behavior of biocides and toxicity of leachates from renders with either free or encapsulated biocides. Both render types contained equal amounts of terbutryn, 2-octyl-3(2H)-isothiazolinone (OIT), and 4,5-dichloro-2-n-octyl-4-isothiazolino-3-one (DCOIT). Nine leachate samples were generated over 9 immersion cycles according to a European standard, and biocides were quantified. The first and ninth leachate samples were tested using bioassays with algae, bacteria, and water fleas, the first sample was also tested with earthworms and springtails. Encapsulation reduced leaching of terbutryn, OIT, and DCOIT by 4-, 17-, and 27-fold. For aquatic organisms, the toxicity of water from render containing encapsulated biocides was always lower than that of render with free biocides. Furthermore, toxicity decreased by 4- to 5-fold over the 9 immersion cycles. Inhibition of photosynthesis was the most sensitive endpoint, followed by algal growth rate, bacterial bioluminescence, and water flea reproduction. Toxicity to algae was due to terbutryn and toxicity to bacteria was due to OIT. None of the samples affected soil organisms. Results demonstrate that combining standardized leaching tests with standardized bioassays is a promising approach to evaluate the ecotoxicity of biocides that leach from facade renders. Environ Toxicol Chem 2018;37:2246-2256. © 2018 SETAC.

Evaluation of the impact of construction products on the environment by leaching of possibly hazardous substances

Construction products are in contact with water (e.g., rain, seepage water) during their service lifetime and may release potentially harmful compounds by leaching processes. Monitoring studies showed that compounds attributed to construction products are found in storm water and the receiving bodies of water and that the release of biocides in urban areas can be comparable to the input of pesticides from agricultural uses. Therefore, a prospective risk assessment of such products is necessary. Laboratory leaching tests have been developed by the Technical Committee CEN/TC 351 and are ready to use. One major task in the future will be the evaluation of the leaching test results, as concentrations found in laboratory experiments are not directly comparable to the field situations. Another task will be the selection of compounds to be considered for construction products, which are often a complex mixture and contain additives, pigments, stabilization agents, etc. The formulations of the products may serve as a starting point, but total content is a poor predictor for leachability, and analysis of the eluates is necessary. In some cases, non-targeted approaches might be required to identify compounds in the eluates. In the identification process, plausibility checks referring to available information should be included. Ecotoxicological tests are a complementary method to test eluates, and the combined effects of all compounds-including degradation products-are included. A bio test battery has been applied in a round robin test and was published in a guidance document. Published studies on the ecotoxicity of construction products show the tests' suitability to distinguish between products with small and larger effects on the environment.