Analysis of estrogenic compounds in environmental and biological samples by liquid chromatography–tandem mass spectrometry with stable isotope-coded ionization-enhancing reagent

Rapid Analysis of Estrogens in Meat Samples by High Performance Liquid Chromatography with Fluorescence Detection

A novel reagent named 4-(N-methyl-1,3-dioxo-benzoisoquinolin-6-yl-oxy)benzene sulfonyl chloride (MBIOBS-Cl) for the determination of estrogens in food samples by high-performance liquid chromatography (HPLC) with fluorescence detection has been developed. Estrogens could be easily labeled by MBIOBS-Cl in Na2CO3-NaHCO3 buffer solution at pH 10.0. The complete labeling reaction for estrogens could be accomplished within five minutes, the corresponding derivatives exhibited strong fluorescence with the maximum excitation and emission wavelengths at 249 nm and 443 nm, respectively. The derivatization conditions, such as the molar ratio of reagent to estrogens, derivatization time, pH, temperature, and buffers were optimized. Derivatives were sufficiently stable to be efficiently analyzed by HPLC with a reversed-phase Agilent ZORBAX 300SB-C18 column with a good baseline resolution. Excellent linear correlations were obtained for all estrogen derivatives with correlation coefficients greater than 0.9998. Ultrasonic-Assisted extraction was used to optimize the extraction of estrogens from meat samples with a recovery higher than 82%. The detection limits (LOD, S/N = 3) of the method ranged from 0.95 to 3.3 μg· kg-1. The established method, which is fast, simple, inexpensive, and environment friendly, can be successfully applied for the detection of four steroidal estrogens from meat samples with little matrix interference.

Pyridinium and ammonium stable isotope labeling agents and their performance in the analysis of alkylamines in food and food packaging materials

Two pairs of stable isotope labeling (SIL) agents, (4-carboxyphenyl)trimethylammonium iodide (d₀-CPTA) and its deuterated counterpart d₃-CPTA, 1-methyl-nicotinamide iodide (d₀-MNA) and its deuterated counterpart d₃-MNA, were designed and synthesized. Their mass spectrometry (MS) sensitivity enhancement effect was studied and compared with commercial dansyl chloride to provide inspiration for labeling agent design. CPTA with quaternary ammonium group showed much higher MS sensitivity enhancement effect and was applied to the SIL analysis of alkylamines in food and food packaging materials. The matrix effect was minimized due to the SIL strategy and the permanent charge of the CPTA. The limits of detection (LODs) were in the range of 2.9-5.1 ng/L, and the limits of quantitation (LOQs) were in the range of 9.6-16.8 ng/L. The recoveries ranged from 91.2 % to 97.1 % with relative standard deviations of less than 6.6 %, and the matrix effect ranged from -1.8 % to -4.9 %.

Analytical derivatizations in environmental analysis

Analytical derivatization is a technique that alters the structure of an analyte and produces a product more suitable for analysis. While this process can be time-consuming and add reagents to the procedure, it can also facilitate the isolation of the analyte(s), enhance analytes' stability, improve separation and sensitivity, and reduce matrix interferences. Since derivatization is a functional group analysis, it improves selectivity by separating reactive from neutral compounds during sample preparation. This technique introduces detector-orientated tags into analytes that lack suitable physicochemical properties for detection at low concentrations. Notably, many regulatory bodies, especially those in the environmental field, require these characteristics in analytical methods. This review focuses on note-worthy analytical derivatization methods employed in environmental analyses with functional groups, phenol, carboxylic acid, aldehyde, ketone, and thiol in aqueous, soil, and atmospheric sample matrices. Both advantages and disadvantages of analytical derivatization techniques are discussed. In addition, we discuss the future directions of analytical derivatization methods in environmental analysis and the potential challenges.

Options of the Main Derivatization Approaches for Analytical ESI and MALDI Mass Spectrometry

The inclusion of preliminary chemical labeling (derivatization) in the analysis process by such powerful and widespread methods as electrospray ionization (ESI) and matrix-assisted laser desorption/ionization (MALDI) mass spectrometry (MS) is a popular and widely used methodological approach. This is due to the need to remove some fundamental limitations inherent in these powerful analytic methods. Although a number of special reviews has been published discussing the utilization of derivatization approaches, the purpose of the present critical review is to comprehensively summarize, characterize and evaluate most of the previously developed and practically applied, as well as recently proposed representative derivatization reagents for ESI-MS and MALDI-MS platforms in their mostly sensitive positive ion mode and frequently hyphenated with separation techniques. The review is focused on the use of preliminary chemical labeling to facilitate the detection, identification, structure elucidation, quantification, profiling or MS imaging of compounds within complex matrices. Two main derivatization approaches, namely the introduction of permanent charge-fixed or highly proton affinitive residues into analytes are critically evaluated. In situ charge-generation, charge-switch and charge-transfer derivatizations are considered separately. The potential of using reactive matrices in MALDI-MS and chemical labeling in MS-based omics sciences is given.

Preparation of sheet-like covalent organic frameworks and their application for efficient preconcentration of 4-(tert-octyl)-phenol and 4-nonylphenol in textiles

In the design of highly ordered (covalent organic frameworks) COFs with "ordered domains size and orientation" construction in a well-defined arrangement, the molecular monomers are the key factors. Here, the effect of molecular monomers on the construction of COFs has been studied, and two kinds of molecular monomers, i.e., ethanediamine (flexible amine ligand) and 4,4'-diaminobiphenyl (rigid amine ligand) have been used for developing sheet-like COFs-I and sheet-like COFs-II, respectively. Furthermore, they have been evaluated in the dispersive solid phase extraction (dSPE) procedure for textiles prior to the analysis of alkylphenol by liquid chromatography-tandem quadrupole mass spectrometry (LC-MS/MS). The results showed that, the optimal usage amount of sheet-like COFs-II used in the dSPE procedure was less than that of sheet-like COFs-I, which may be explained by much higher adsorption capacity of sheet-like COFs via hydrogen-bonding and π-π stacking interactions. Rectilinear calibration graphs were obtained for 4-(tert-octyl)-phenol (4-tOP) and 4-nonylphenol (4-NP) in the range 0.2-20 µg/kg with determination coefficient (r²) higher than 0.9990, and the limits of detection (LODs) of 4-tOP and 4-NP were 0.039 µg/kg and 0.048 µg/kg, respectively. The developed method has been successfully applied to analysis of 50 textile samples, in which 4-tOP and 4-NP were found in six samples with concentrations in the range of 1.6 μg/kg-20.9 μg/kg.

Permanently Positively Charged Stable Isotope Labeling Agents and Its Application in the Accurate Quantitation of Alkylphenols Migrated from Plastics to Edible Oils

A new permanently positively charged stable isotope labeling (SIL) agent pair, 4-(((2,5-dioxopyrrolidin-1-yl)oxy)carbonyl)-N,N,N-trimethylbenzenaminium iodide(DPTBA) and its deuterated counterpart d₃-DPTBA, was designed and synthesized. The SIL agents were applied to the liquid chromatography-tandem mass spectrometry analysis of alkylphenols. Light labeled standards and heavy labeled samples were mixed and analyzed simultaneously. Matrix effect which mainly occurred during the ionization process was minimized because of the identical ionization processes between samples and standards. Meanwhile, derivatization made alkylphenols be positively charged, and thus the sensitivity was enhanced. The limits of detection were in the range of 1.5-1.8 ng/L, and the limits of quantitation were in the range of 4.8-6.1 ng/L. The developed method was applied to analyze alkylphenols migrated from plastics to edible oils. The recoveries for all analytes were in the range of 88.6-95.3%, while the matrix effects for all analytes were in the range of 96.2-99.6%.

Quantitative amino acid analysis by liquid chromatography-tandem mass spectrometry using low cost derivatization and an automated liquid handler

Amino acid analysis is central to newborn screening and the investigation of inborn errors of metabolism. Ion‐exchange chromatography with ninhydrin derivatization remains the reference method for quantitative amino acid analysis but offers slow chromatography and is susceptible to interference from other co‐eluting compounds. Liquid‐chromatography tandem mass spectrometry (LC‐MS/MS) provides a rapid and highly specific alternative, but sample preparation is frequently laborious and sometimes cost prohibitive. To address these limitations, we validated an LC‐MS/MS method using the aTRAQ Reagents Application Kit with a modified protocol consuming only half reagents. Adequate performance for clinical specimen measurement of 26 amino acids with high clinical relevance was achieved. An automated liquid handler and modified calibration and normalization approaches were used to ensure reproducible assay performance. Linear measurement between 5 and 2000 μM was achieved for most analytes despite use of a small, 10 μl sample size. Overall the method achieved near substantially improved throughput and enabled use of smaller samples volumes for batched analyses of clinical samples.

Amino and organic acid analysis: Essential tools in the diagnosis of inborn errors of metabolism

Inborn errors of metabolism (IEMs) are a large class of genetic disorders that result from defects in enzymes involved in energy production and metabolism of nutrients. For every metabolic pathway, there are defects that can occur and potentially result in an IEM. While some defects can go undetected in one's lifetime, some have moderate to severe clinical consequences. In the latter case, the biochemical defect leads to accumulation of metabolites and byproducts that are toxic or interfere with normal biological function. Disorders of amino acid metabolism, organic acid metabolism and the urea cycle comprise a large portion of IEMs. Two essential tools required for the diagnosis of these categories of disorders are amino acid and organic acid profiling. Most all clinical laboratories offering metabolic testing perform amino acid analysis, while organic acid profiling is restricted to more specialized pediatric hospitals and reference laboratories. In this chapter, we will provide an overview of various methodologies employed for amino acid and organic acid profiling as well as specific examples to demonstrate how these techniques are applied in clinical laboratories for the diagnosis of IEMs.

Azo coupling-based derivatization method for high-sensitivity liquid chromatography-tandem mass spectrometry analysis of tetrahydrocannabinol and other aromatic compounds

An azo coupling-based derivatization method is reported for high-sensitivity liquid chromatography-tandem mass spectrometry (LC-MS/MS) quantitation of tetrahydrocannabinol (THC) and other aromatic compounds, i.e. phenols and amines. Through the azo coupling of a diazonium to an analyte, it produces a derivatized analyte which has enhanced ionization efficiency and results in high-response fragments in tandem mass spectrometry. The derivatization method was applied to six typical aromatic compounds using three different diazonium salts as derivatization reagents, demonstrating its applicability to a variety of analytes and reagents. The derivatization reaction can be directly carried out in neat samples, and after derivatization the samples can be immediately sent to the LC-MS/MS instrument for analysis. These advantages facilitate a one-step sample preparation procedure that can be completed in less than one hour, allowing for a "derivatize & shoot" lab workflow. The derivatization method was applied to establish an LC-MS/MS assay for the quantitation of THC in human breath samples. The derivatization conditions were studied in this application, including the effects of acidity, organic solvent, and diazonium concentration in the reaction. The THC derivatization assay was validated and achieved a limit of quantitation (LOQ) of 0.50 pg/ml using either of the two regio-isomers of the azo-derivative of THC (THC-DRV). To prove that the derivatization method has compatibility with complex-matrix samples, a THC derivatization assay for serum samples was established, in which the azo coupling reaction was directly carried out in crude protein-precipitated supernatants. An LOQ of 5.0 pg/ml was achieved. In addition, excellent correlation between THC derivatization and non-derivatization assays was found in the analysis of whole blood samples.

Cationic gemini surfactant-resorcinol-aldehyde resin and its application in the extraction of endocrine disrupting compounds from food contacting materials

A new cationic gemini surfactant-resorcinol/formaldehyde resin was designed and synthesized. Cationic gemini surfactant was introduced into the resorcinol/formaldehyde resin for the first time and led to the retention of negatively charged endocrine disrupting compounds (EDCs) through electrostatic interactions, hydrogen bonding and π-π interactions. The synthesized material showed good performance in the dispersive micro-solid phase extraction (D-μ-SPE) of EDCs such as alkylphenol and phenoxy acid herbicides from food packaging migrants. Extraction parameters such as pH, adsorbent dose, extraction time and salting out effect were optimized. The limits of detections were in the range of 0.5-0.8 ng/mL, and the recoveries were in the range of 90-100%. The developed method was applied to the analysis of EDCs from food contacting materials migrants with pentachlorophenol, 2,4-dichlorophenoxyacetic acid and bisphenol A detected in the concentration range of 0.2-1.2 mg/kg. It also showed great potential in the D-μ-SPE of other compounds with negative charge or high hydrophobicity.

Rapid and sensitive determination of multiple endocrine-disrupting chemicals by ultrasound-assisted in situ derivatization dispersive liquid-liquid microextraction coupled with ultra-high-performance liquid chromatography/tandem mass spectrometry

RATIONALE

Endocrine-disrupting chemicals (EDCs) in environment samples and food stuffs are an increasing serious public health issue due to their potency to interfere and deregulate several aspects of the endocrine system. Because of their extremely low abundance, it remains a challenging task to develop a sensitive detection method.

METHODS

4'-Carbonyl chloride rosamine (CCR) was used as a derivatization reagent for EDCs for the first time. A new ultrasound-assisted in situ derivatization/dispersive liquid-liquid microextraction (UA-DLLME with in situ derivatization) method for multiple EDCs including five estrogens, two alkylphenols, eight bisphenols, seven parabens and triclosan coupled with ultra-high-performance liquid chromatography/tandem mass spectrometry (UHPLC/MS/MS) has been developed and validated.

RESULTS

The ionization efficiency of EDCs was greatly enhanced through the introduction of a permanent charged moiety of CCR into the derivatives during electrospray ionization (ESI)-MS analysis. The main variables potentially affecting the UA-DLLME with in situ derivatization process are optimized. The recoveries and matrix effects of 23 EDCs for the spiking samples were in the range of 83.0-116.0% and 85.8-114.6%, respectively. Good method reproducibility was achieved.

CONCLUSIONS

The limits of detection (LODs) for 23 EDCs were 0.05-0.40 ng/L and 0.03-0.25 ng/g (dry weight, d.w.) for environment samples and food stuffs, respectively. The proposed method has been demonstrated to be suitable for simultaneous determination of multiple EDCs in real samples with high sensitivity, speediness, and good sample clean-up ability. Copyright © 2017 John Wiley & Sons, Ltd.

Gas Purge Microextraction Coupled with Stable Isotope Labeling-Liquid Chromatography/Mass Spectrometry for the Analysis of Bromophenols in Aquatic Products

A green, sensitive, and accurate method was developed for the extraction and determination of bromophenols (BPs) from aquatic products by using organic solvent-free gas purge microsyringe extraction (GP-MSE) technique in combination with stable isotope labeling (SIL) strategy. BPs were extracted by NaHCO₃ buffer solution, with recoveries varying from 92.0% to 98.5%. The extracted solution was analyzed by SIL strategy, during which analytes and standards were labeled by 10-methyl-acridone-2-sulfonyl chloride (d₀-MASC) and its deuterated counterpart d₃-MASC, respectively. The labeling reaction was finished within 10 min with good stability. The liquid chromatography-tandem mass spectrometry (HPLC-MS/MS) sensitivity of BPs was greatly enhanced due to the mass-enhancing property of MASC, while the matrix effect was effectively minimized by the SIL strategy. The limits of detection (LODs) were in the range of 0.10-0.30 μg/kg, while the limits of quantitations (LOQs) were in the range of 0.32-1.0 μg/kg. The proposed method also showed great potential in the qualitative analysis of other bromophenols in the absence of standard.

DnsID in MyCompoundID for rapid identification of dansylated amine- and phenol-containing metabolites in LC-MS-based metabolomics

High-performance chemical isotope labeling (CIL) liquid chromatography-mass spectrometry (LC-MS) is an enabling technology based on rational design of labeling reagents to target a class of metabolites sharing the same functional group (e.g., all the amine-containing metabolites or the amine submetabolome) to provide concomitant improvements in metabolite separation, detection, and quantification. However, identification of labeled metabolites remains to be an analytical challenge. In this work, we describe a library of labeled standards and a search method for metabolite identification in CIL LC-MS. The current library consists of 273 unique metabolites, mainly amines and phenols that are individually labeled by dansylation (Dns). Some of them produced more than one Dns-derivative (isomers or multiple labeled products), resulting in a total of 315 dansyl compounds in the library. These metabolites cover 42 metabolic pathways, allowing the possibility of probing their changes in metabolomics studies. Each labeled metabolite contains three searchable parameters: molecular ion mass, MS/MS spectrum, and retention time (RT). To overcome RT variations caused by experimental conditions used, we have developed a calibration method to normalize RTs of labeled metabolites using a mixture of RT calibrants. A search program, DnsID, has been developed in www.MyCompoundID.org for automated identification of dansyl labeled metabolites in a sample based on matching one or more of the three parameters with those of the library standards. Using human urine as an example, we illustrate the workflow and analytical performance of this method for metabolite identification. This freely accessible resource is expandable by adding more amine and phenol standards in the future. In addition, the same strategy should be applicable for developing other labeled standards libraries to cover different classes of metabolites for comprehensive metabolomics using CIL LC-MS.

Rapid analysis of biogenic amines from rice wine with isotope-coded derivatization followed by high performance liquid chromatography-tandem mass spectrometry

A pair of isotope-coded derivatization reagents, d0-10-methyl-acridone-2-sulfonyl chloride (d0-MASC, light form) and d3-10-methyl-acridone-2-sulfonyl chloride (d3-MASC, heavy form), were used for labeling biogenic amines (BAs). On basis of the isotope-coded derivatization, a global isotope internal standard quantitative method for determining seven BAs by high-performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS) was developed. The d0-MASC and d3-MASC can easily label BAs under mild conditions within 15 min at 50 °C. The obtained light and heavy labeled BAs were monitored by the transitions of [M+H](+) → 208 and [M+H](+) → 211, respectively. Relative quantification of BAs was achieved by calculation of the peak area ratios of d0-MASC/d3-MASC labeled derivatives. Excellent linear responses for relative quantification were observed in the range of 1/10-10/1. The developed method has been successfully applied to the quantification of BAs in Chinese rice wine with recoveries ranging from 94.9% to 104.5%.

Measurement of Estradiol in Human Serum by LC-MS/MS Using a Novel Estrogen-Specific Derivatization Reagent

A liquid chromatography-tandem mass spectrometry (LC-MS/MS) method is described that employs a novel derivatization reagent for the measurement of serum estradiol (E2), with simultaneous analysis of underivatized testosterone (T) and dihydrotestosterone (DHT). The main advantage of the new derivatization reagent 1,2-dimethylimidazole-5-sulfonyl chloride is its analyte-specific fragmentation that enables monitoring of confirmatory mass transitions with high sensitivity. The reaction mixture can be analyzed without additional purification steps using a 9.5 min gradient run, and sensitive detection is achieved with a triple quadrupole mass spectrometer using atmospheric pressure photoionization. Method validation was performed with human serum samples, including a comparison with a standard LC-MS/MS method using 120 samples from a clinical study, and analysis of certified E2 serum reference materials BCR-576, BCR-577, and BCR-578. The lower limits of quantification for E2, T, and DHT were 0.5 pg/mL, 25 pg/mL, and 0.10 ng/mL, respectively, from a 200-μL sample. Validation results indicated good accuracy and agreement with established, conventional LC-MS/MS assays, demonstrating suitability for analysis of samples containing E2 in the low pg/mL range, such as serum from men, children, and postmenopausal women.

Accurate Determination of Amino Acids in Serum Samples by Liquid Chromatography-Tandem Mass Spectrometry Using a Stable Isotope Labeling Strategy

An accurate and sensitive liquid chromatography-tandem mass spectrometry method was developed for the analysis of amino acids (isoleucine, leucine, valine, tyrosine, phenylalanine and tryptophan) in serum samples using a stable isotope labeling strategy. Amino acid samples and standards were, respectively, derivatized by 10-methyl-acridone-2-sulfonyl chloride (d0-MASC) and its deuterated counterpart d3-MASC to form isotopic pairs which co-eluted and were detected by an MS detector at the same time. Accurate internal standard-based quantification was thereby achieved without the use of any internal standard analogy. The labeling reaction of MASC with amino acids is fast, simple and robust. Besides, derivatization increased the molecular weight of amino acids, and therefore they were shifted out of the background noise which was often observed in low mass region. The instrument LODs were in the range of 1.0-2.5 nmol/L. Linearities calculated by comparing theoretical peak area ratios of d0-/d3-MASC derivatives with the experimental peak area ratios were excellent with correlation coefficients of >0.995. The proposed method was successfully applied to the analysis of amino acids in serum samples with high sensitivity and accuracy.

Effects of sample injection amount and time-of-flight mass spectrometric detection dynamic range on metabolome analysis by high-performance chemical isotope labeling LC-MS

The effect of sample injection amount on metabolome analysis in a chemical isotope labeling (CIL) liquid chromatography-mass spectrometry (LC-MS) platform was investigated. The performance of time-of-flight (TOF) mass spectrometers with and without a high-dynamic-range (HD) detection system was compared in the analysis of (12)C2/(13)C2-dansyl labeled human urine samples. An average of 1635 ± 21 (n = 3) peak pairs or putative metabolites was detected using the HD-TOF-MS, compared to 1429 ± 37 peak pairs from a conventional or non-HD TOF-MS. In both instruments, signal saturation was observed. However, in the HD-TOF-MS, signal saturation was mainly caused by the ionization process, while in the non-HD TOF-MS, it was caused by the detection process. To extend the MS detection range in the non-HD TOF-MS, an automated switching from using (12)C to (13)C-natural abundance peaks for peak ratio calculation when the (12)C peaks are saturated has been implemented in IsoMS, a software tool for processing CIL LC-MS data. This work illustrates that injecting an optimal sample amount is important to maximize the metabolome coverage while avoiding the sample carryover problem often associated with over-injection. A TOF mass spectrometer with an enhanced detection dynamic range can also significantly increase the number of peak pairs detected.

BIOLOGICAL SIGNIFICANCE

In chemical isotope labeling (CIL) LC-MS, relative metabolite quantification is done by measuring the peak ratio of a (13)C2-/(12)C2-labeled peak pair for a given metabolite present in two comparative samples. The dynamic range of peak ratio measurement does not need to be very large, as only subtle changes of metabolite concentrations are encountered in most metabolomic studies where relative metabolome quantification of different groups of samples is performed. However, the absolute concentrations of different metabolites can be very different, requiring a technique to provide a wide detection dynamic range to allow the detection of as many peak pairs as possible. In this work, we demonstrated that controlling the sample injection amount into LC-MS was critical to achieve the optimal detectability while avoiding sample carry-over problem. In addition, the use of a high-dynamic-range TOF system increased the number of peak pairs detected, compared to a conventional TOF system. We also investigated the ionization and detection saturation factors limiting the dynamic range of detection. This article is part of a Special Issue entitled: Protein dynamics in health and disease. Guest Editors: Pierre Thibault and Anne-Claude Gingras.

An in-advance stable isotope labeling strategy for relative analysis of multiple acidic plant hormones in sub-milligram Arabidopsis thaliana seedling and a single seed

A sensitive and reliable in-advance stable isotope labeling strategy was developed for simultaneous relative quantification of 8 acidic plant hormones in sub-milligram amount of plant materials. Bromocholine bromide (BETA) and its deuterated counterpart D9-BETA were used to in-advance derivatize control and sample extracts individually, which were then combined and subjected to solid-phase extraction (SPE) purification followed by UPLC-MS/MS analysis. Relative quantification of target compounds was obtained by calculation of the peak area ratios of BETA/D9-BETA labeled plant hormones. The in-advance stable isotope labeling strategy realized internal standard-based relative quantification of multiple kinds of plant hormones independent of availability of internal standard of every analyte with enhanced sensitivity of 1-3 orders of magnitude. Meanwhile, the in-advance labeling contributes to higher sample throughput and more reliability. The method was successfully applied to determine 8 plant hormones in 0.8mg DW (dry weight) of seedlings and 4 plant hormones from single seed of Arabidopsis thaliana. The results show the potential of the method in relative quantification of multiple plant hormones in tiny plant tissues or organs, which will advance the knowledge of the crosstalk mechanism of plant hormones.