Crosslinked polymeric ionic liquids as solid-phase microextraction sorbent coatings for high performance liquid chromatography

Multivariate optimization for extraction of 2-methylimidazole and 4-methylimidazole from açaí-based food products using polymeric ionic liquid-based sorbent coatings in solid-phase microextraction coupled to gas chromatography-mass spectrometry

In this study, polymeric ionic liquids featuring different functional moieties were applied as sorbent coatings in direct-immersion solid-phase microextraction (DI-SPME) for the extraction of 2-methylimidazole (2-MI) and 4-methylimidazole (4-MI) from açaí-based food products followed by gas chromatography-mass spectrometry (GC-MS) analysis. The analytical method was optimized using a sequential experimental design. Variables used in GC-MS such as desorption time, as well as for SPME-DI, including extraction time, extraction temperature, incubation time of extraction, amount of NaCl in the extract, and stirring rate, were optimized. The fitness-for-purpose of the method was verified by the linearity of matrix-matched calibration curves (R2 ≥ 0.9921), adequate recoveries (81.7-89.7 %), and precision (relative standard deviations ≤11.2 %). The method was applied to twenty-five samples of açaí-based food products. 4-MI was found in four samples whereas 2-MI was not detected above the limit of detection. The method was found to be suitable for quality control analysis.

Understanding the influence of polymeric ionic liquid sorbent coating substituents on cannabinoid and pesticide affinity in solid-phase microextraction

To understand factors that drive pesticide-cannabinoid selectivity in solid-phase microextraction (SPME), eight new polymeric ionic liquid (PIL) sorbent coatings were designed and compared to four previously reported PIL sorbent coatings for the extraction of pesticides. The four PIL sorbent coatings consisted of either vinylimidazolium or vinylbenzylimidazolium ILs with long alkyl chain substituents (i.e., -C8H17 or -C12H25) and bis[(trifluoromethyl)sulfonyl]imide ([NTf2-]) anions, from which the eight new PIL sorbent coatings were adapted. Modifications to the chemical structure of IL monomers and crosslinkers included incorporation of polymerizable p-styrenesulfonate or 3-sulfopropyl acrylate anions, the addition of aromatic moieties, and/or the addition of polar functional groups (i.e., -OH or -O- groups). A total of ten commonly regulated pesticides and six cannabinoids were examined in this study. The effect of salt on the solubility of pesticides and cannabinoids in aqueous solutions was assessed by determining their extraction efficiencies in the presence of varied methanol content. Differences in their solubilities appear to play a dominant role in enhancing pesticide-cannabinoid selectivity. The selectivity, represented as the ratio of pesticide total peak areas to cannabinoid total peak areas, also exhibited a moderate correlation to the affinity of the sorbent coatings towards both the pesticides and the cannabinoids. A positive correlation was observed for the pesticides and a negative correlation was observed for the cannabinoids, suggesting that selectivity was driven by more than the presence of salt in the samples. The sorbent coatings' affinity towards each class of analytes were examined to determine specific interactions that might influence selectivity. The two main structural modifications increasing pesticide-cannabinoid selectivity included the absence of aromatic moieties and the addition of hydrogen bond donor functional groups. Extractions of simple aromatic molecules as probes were performed under similar extraction conditions as the cannabinoids and confirmed the influence of hydrogen bonding interactions on sorbent coating affinity.

Batch Scale Production of 3D Printed Extraction Sorbents Using a Low-Cost Modification to a Desktop Printer

This study reports a simple modification to a commercial resin 3D printer that significantly reduces the amount of prepolymer material needed for the production of extraction sorbents. The modified printing platform is demonstrated in the printing of two imidazolium-based ionic liquid (IL) monomers. Two geometries resembling a blade-type polymeric ionic liquid (PIL) sorbent used in thin-film microextraction and a fiber-type sorbent used in solid-phase microextraction (SPME) were printed. The SPME PIL sorbents were used to extract 10 organic contaminants, including plasticizers, antimicrobial agents, UV filters, and pesticides, from water followed by high-performance liquid chromatographic (HPLC) analysis. To compare the extraction performance of the SPME sorbents, seven fibers printed with the same prepolymer composition from the same printing batch as well as different batches were evaluated. The results revealed highly reproducible extraction efficiencies for all tested sorbents with no statistical difference in their extraction performance. Method validation showed acceptable linearity (R2 > 0.92) for all analytes with limits of detection and limits of quantification ranging from 0.13 to 45 μg L-1 and 0.43 to 150 μg L-1, respectively.

Selective isolation of pesticides and cannabinoids using polymeric ionic liquid-based sorbent coatings in solid-phase microextraction coupled to high-performance liquid chromatography

The high abundance of cannabinoids within cannabis samples presents an issue for pesticide testing as cannabinoids are often co-extracted with pesticides using various sample preparation techniques. Cannabinoids may also chromatographically co-elute with moderate polarity pesticides and inhibit the ionization of pesticides when using mass spectrometry. To circumvent these issues, we have developed a new approach to isolate commonly regulated pesticides and cannabinoids from aqueous samples using tunable, crosslinked imidazolium polymeric ionic liquid (PIL)-based sorbent coatings for direct immersion solid-phase microextraction (DI-SPME). The selectivity of four PIL sorbent coatings towards 20 pesticides and six cannabinoids, including cannabidiol and Δ⁹-THC, was investigated and compared against a commercial PDMS/DVB fiber. Extraction and desorption conditions, including salt content, extraction temperature, pH, extraction time, desorption solvent, and desorption time, were optimized using high-performance liquid chromatography (HPLC) with ultraviolet (UV) detection. Under optimized conditions, the PIL fiber consisting of 1-vinylbenzyl-3-octylimidazolium bis[(trifluoromethyl)sulfonyl]imide ([VBIMC₈⁺][NTf₂^-]) and 1,12-di(3-vinylbenzylimidazolium)dodecane dibis[(trifluoromethyl)sulfonyl]imide ([(VBIM)₂C₁₂²⁺]2[NTf₂^-]) sorbent coating provided the best selectivity towards pesticides compared to other PILs and the PDMS/DVB fibers and was able to reach limits of detection (LODs) as low as 1 µg/L. When compared to a previously reported PIL-based SPME HPLC-UV method for pesticide analysis, the amount of cannabinoids extracted from the sample was decreased 9-fold while a 4-fold enhancement in the extraction of pesticides was achieved. Additionally, the PIL-based SPME method was applied to samples containing environmentally-relevant concentrations of pesticides and cannabinoids to assess its feasibility for Cannabis quality control testing. Relative recoveries between 95% and 141% were obtained using the PIL sorbent coating while recoveries ranging from 50% to 114% were obtained using the PDMS/DVB fiber.

Ionic Liquid-Assisted DLLME and SPME for the Determination of Contaminants in Food Samples

Developing effective and green methods for food analysis and separation has become an urgent issue regarding the ever-increasing concern of food quality and safety. Ionic liquids (ILs) are a new chemical medium and soft functional material developed under the framework of green chemistry and possess many unique properties, such as low melting points, low-to-negligible vapor pressures, excellent solubility, structural designability and high thermal stability. Combining ILs with extraction techniques not only takes advantage of ILs but also overcomes the disadvantages of traditional extraction methods. This subject has attracted intensive research efforts recently. Here, we present a brief review of the current research status and latest developments regarding the application of IL-assisted microextraction, including dispersive liquid–liquid microextraction (DLLME) and solid-phase microextraction (SPME), in food analysis and separation. The practical applications of ILs in determining toxic and harmful substances in food specimens with quite different natures are summarized and discussed. The critical function of ILs and the advantages of IL-based microextraction techniques over conventional extraction techniques are discussed in detail. Additionally, the recovery of ILs using different approaches is also presented to comply with green analytical chemistry requirements.

Highly Sensitive and Selective Eco-Toxic 4-Nitrophenol Chemical Sensor Based on Ag-Doped ZnO Nanoflowers Decorated with Nanosheets

Herein, we have developed a novel sensing electrode to detect the eco-toxic 4-nitrophenol (4-NP). Ag-doped-ZnO nanoflowers were synthesized by facile hydrothermal method and examined by several characterization techniques in order to understand the morphology, crystal structure, composition, and surface properties. Morphological results were confirmed by the formation of Ag-doped ZnO nanoflowers decorated with nanosheets. Ag-doped ZnO/glassy carbon electrode (GCE) electrode-material-matrix was used for electrochemical sensing of toxic 4-NP. Under optimized conditions, Ag-doped ZnO/GCE modified electrode exhibits high-sensitivity and selectivity compared to the bare GCE electrode. The Ag-doped ZnO/GCE modified electrode exhibits high electrocatalytic oxidation towards 4-NP. Anodic peak current of 4-NP is increased linearly by increasing the concentration of nitrophenol. Additionally, Ag-doped ZnO/GCE shows a wide range of sensitivity from 10 µM to 500 µM, and a linear calibration plot with a good detection limit of 3 µM (S/N = 3). The proposed Ag-doped ZnO/GCE modified electrode showed high sensing stability. In addition, the oxidation mechanism was studied. The obtained results revealed that the Ag-ZnO/GCE electrode could be the promising sensing electrode for 4-NP sensing.

Surface-tuned hierarchical ɤ-Fe2O3-N-rGO nanohydrogel for efficient catalytic removal and electrochemical sensing of toxic nitro compounds

4- Nitrophenol (4-NP) is a top rated hazardous environmental pollutant and secondary explosive chemicals. For the sake of ecology and environment safety, the catalytic reduction and detection of 4-NP is highly important. In this work, ɤ-Fe₂O₃-nitrogen doped rGO (ɤ-Fe₂O₃-N-rGO) nanohydrogel was synthesized by green hydrothermal method. The morphology and phase purity of prepared ɤ-Fe₂O₃-N-rGO nanohydrogel were confirmed by various analytical (SEM, TEM, XRD, and XPS) and electrochemical techniques. The morphological structure of ɤ-Fe₂O₃-N-rGO nanohydrogel confirmed that the nanocrystals are well covered over the 2D N-rGO layer. Further, ɤ-Fe₂O₃-N-rGO nanohydrogel was applied for the catalytic reduction and electrochemical detection of ecotoxic 4-NP. A low cost, ɤ-Fe₂O₃-N-rGO nanohydrogel displayed an excellent catalytic activity, high recyclability (>5 cycles) and high conversion efficiency of 4-NP to 4-Aminophenol (4-AP). In addition, ɤ-Fe₂O₃-N-rGO nanohydrogel modified GCE displayed a wide linear sensing range (0.1-1000 μM), and a low detection limit (LOD) of 0.1 μM with excellent sensitivity, high selectivity (<1.2%) and good stability (>4 weeks). The developed sensor electrode shows the low reduction potential of -0.3 V and -0.60 V for the determination of 4-NP. The proposed ɤ-Fe₂O₃-N-rGO nanohydrogel is promising catalyst for the detection and removal of toxic aromatic nitro compounds in real site applications.

Switchable solvent-based micro-extraction of pesticides in food and environmental samples

Switchable solvents are new generation solvents that are environmentally friendly and can be used for the effective pre-concentration of pesticide residues in food and environmental matrices. They have physico-chemical properties that can be switched abruptly and reversibly between two opposite forms. The common switchable solvents used commonly during pesticide pre-concentration involve polarity switch. Such solvent switch between hydrophobic and hydrophilic forms during pesticide pre-concentration. Secondary and tertiary amines are typical switchable hydrophilicity solvents. The amines are hydrophobic but they abruptly and reversibly switch to their hydrophilic forms on addition of CO₂ to them. The application of amine-based switchable solvents during pre-concentration of pesticide residue in food and environmental samples are discussed in this paper. Medium-chain fatty acids can also be used as switchable solvents. Their switch between hydrophobic and hydrophilic forms is usually triggered by pH changes. Applications of fatty acid-based switchable solvents during pre-concentration of pesticide residues are reviewed in this paper. Switchable solvent-based micro-extraction can be combined with other pre-concentration techniques to enhance selectivity resulting in clean chromatograms. This paper has a section dedicated to the application of hyphenated switchable solvent-based micro-extraction techniques during pre-concentration of pesticides in food and environmental samples. In addition, the challenges associated with the use of switchable solvents during micro-extraction of pesticide residues are also discussed.

Overview of Sample Preparation and Chromatographic Methods to Analysis Pharmaceutical Active Compounds in Waters Matrices

In the environment, pharmaceutical residues are a field of particular interest due to the adverse effects to either human health or aquatic and soil environment. Because of the diversity of these compounds, at least 3000 substances were identified and categorized into 49 different therapeutic classes, and several actions are urgently required at multiple steps, the main ones: (i) occurrence studies of pharmaceutical active compounds (PhACs) in the water cycle; (ii) the analysis of the potential impact of their introduction into the aquatic environment; (iii) the removal/degradation of the pharmaceutical compounds; and, (iv) the development of more sensible and selective analytical methods to their monitorization. This review aims to present the current state-of-the-art sample preparation methods and chromatographic analysis applied to the study of PhACs in water matrices by pinpointing their advantages and drawbacks. Because it is almost impossible to be comprehensive in all PhACs, instruments, extraction techniques, and applications, this overview focuses on works that were published in the last ten years, mainly those applicable to water matrices.

Multi-Walled Carbon Nanotubes for Magnetic Solid-Phase Extraction of Six Heterocyclic Pesticides in Environmental Water Samples Followed by HPLC-DAD Determination

Magnetic multi-walled carbon nanotubes were prepared as magnetic solid-phase extraction (MSPE) adsorbent for the enrichment of six heterocyclic pesticides in environmental water samples, including imidacloprid, triadimefon, fipronil, flusilazole, chlorfenapyr and fenpyroximate. Then six heterocyclic pesticides were separated and determined by high-performance liquid chromatography-diode-array detector (HPLC-DAD). Major factors influencing MSPE efficiency, including the dose of mag-multi-walled carbon nanotubes (mag-MWCNTs), extraction time, solution pH, salt concentration, type and volume of eluent and desorption time were investigated. Under the optimized conditions, the enrichment factor of the method reached to 250. The linearity was achieved within 0.05–10.0 μg/L for imidacloprid and chlorfenapyr, 0.10–10.0 μg/L for fipronil, flusilazole, triadimefon and fenpyroximate. Limits of detection were in the range of 0.01–0.03 μg/L. Good precision at three spiked levels were 1.1–11.2% (intra-day) and 1.7–11.0% (inter-day) with relative standard deviation of peak area, respectively. The developed method was utilized to analyze tap water, river water and reservoir water samples and recoveries at three spiked concentration levels ranged from 72.2% to 107.5%. The method was proved to be a convenient, rapid and practical method for sensitive determination of heterocyclic pesticides.

Highly efficient solid-phase microextraction of polycyclic aromatic hydrocarbons in water based on worm-like nickel-titanium oxide nanocomposites coating grown on a nickel-titanium alloy wire by low-voltage anodization

A novel worm-like nickel-titanium oxide nanocomposite coating was directly grown on a nickel-titanium alloy wire by low-voltage electrochemical anodization in alkaline ethylene glycol and water solution. The in situ growth of nickel-titanium oxide nanocomposites greatly depended on the volume ratio of ethylene glycol to water and temperature. Coupled to high-performance liquid chromatography with UV detection by static desorption in the mobile phase, the adsorption performance of the as-prepared fiber was evaluated for solid-phase microextraction of representative environmental analytes in water. The results indicate that the as-prepared fiber exhibits higher extraction capability for polycyclic aromatic hydrocarbons than commercial polydimethylsiloxane and polyacrylate fibers. After optimizing the extraction parameters, the calibration graphs of the developed method was linear in the range of 0.05-200 μg/L with correlation coefficients above 0.998. Limit of detection ranged from 0.013 to 0.145 μg/L for seven target analytes. Relative standard deviations of intraday and interday analyses varied from 4.0 to 5.3% and from 4.7 to 6.3% with the single fiber, respectively. The relative recoveries of 84.4-109% were achieved for highly efficient enrichment and determination of target analytes in spiked river and snow water. Moreover, the as-prepared fiber can be used more than 200 times.

Determination of Volatile Water Pollutants Using Cross-Linked Polymeric Ionic Liquid as Solid Phase Micro-Extraction Coatings

Ionic liquids found a wide application in catalysis and extraction due to their unique properties. Herein, ethylene glycol dimethacrylate as the cross-linker and 1-vinyl-3- butylimidazolium tetrafluoroborate as functional monomer via thermally initiated free-radical polymerization was prepared as a novel copolymer solid phase micro-extraction (SPME) coating. A surface modified stainless-steel wire was implemented as the substrate. Factors affecting the extraction performances of the copolymer, including the molar ratio of monomers to cross-linkers, the amount of porogen agent, and polymerization time were evaluated and optimized. To evaluate the extraction performance, five commonly seen polycyclic aromatic hydrocarbons (PAHs) were taken as the analytical targets. The potential factors affecting extraction efficiency were optimized. The as-prepared SPME device, coupled with gas chromatography, was successfully applied for the determination of PAHs in water samples. The wide linear range, low detection limit, good reproducibility, selectivity, and excellent thermal stability indicate the promising application of the newly developed SPME fiber in environmental monitoring as well as in other samples having complex matrices.

The Influence of Ionic Liquids on the Effectiveness of Analytical Methods Used in the Monitoring of Human and Veterinary Pharmaceuticals in Biological and Environmental Samples-Trends and Perspectives

Recent years have seen the increased utilization of ionic liquids (ILs) in the development and optimization of analytical methods. Their unique and eco-friendly properties and the ability to modify their structure allows them to be useful both at the sample preparation stage and at the separation stage of the analytes. The use of ILs for the analysis of pharmaceuticals seems particularly interesting because of their systematic delivery to the environment. Nowadays, they are commonly detected in many countries at very low concentration levels. However, due to their specific physiological activity, pharmaceuticals are responsible for bioaccumulation and toxic effects in aquatic and terrestrial ecosystems as well as possibly upsetting the body's equilibrium, leading to the dangerous phenomenon of drug resistance. This review will provide a comprehensive summary of the use of ILs in various sample preparation procedures and separation methods for the determination of pharmaceuticals in environmental and biological matrices based on liquid-based chromatography (LC, SFC, TLC), gas chromatography (GC) and electromigration techniques (e.g., capillary electrophoresis (CE)). Moreover, the advantages and disadvantages of ILs, which can appear during extraction and separation, will be presented and attention will be given to the criteria to be followed during the selection of ILs for specific applications.

Recent Applications and Newly Developed Strategies of Solid-Phase Microextraction in Contaminant Analysis: Through the Environment to Humans

The present review aims to describe the recent and most impactful applications in pollutant analysis using solid-phase microextraction (SPME) technology in environmental, food, and bio-clinical analysis. The covered papers were published in the last 5 years (2014–2019) thus providing the reader with information about the current state-of-the-art and the future potential directions of the research in pollutant monitoring using SPME. To this end, we revised the studies focused on the investigation of persistent organic pollutants (POPs), pesticides, and emerging pollutants (EPs) including personal care products (PPCPs), in different environmental, food, and bio-clinical matrices. We especially emphasized the role that SPME is having in contaminant surveys following the path that goes from the environment to humans passing through the food web. Besides, this review covers the last technological developments encompassing the use of novel extraction coatings (e.g., metal-organic frameworks, covalent organic frameworks, PDMS-overcoated fiber), geometries (e.g., Arrow-SPME, multiple monolithic fiber-SPME), approaches (e.g., vacuum and cold fiber SPME), and on-site devices. The applications of SPME hyphenated with ambient mass spectrometry have also been described.

Bract as a novel extraction phase in thin-film SPME combined with 96-well plate system for the high-throughput determination of estrogens in human urine by liquid chromatography coupled to fluorescence detection

In this study, an environmentally friendly and high-throughput method was developed for the determination of estrone (E1), 17β-estradiol (E2), 17α-ethinylestradiol (EE2) and estriol (E3) in human urine by liquid chromatography-fluorescence detector (HPLC-FLD). A biosorbent (bract) was proposed as extraction phase for Thin-Film SPME combined with 96-well system. The characterization of the biosorbent was performed by Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The optimizations were carried out through univariate and multivariate approaches with optimal conditions comprised of urine samples diluted 40-fold, liquid desorption performed in methanol and addition of 20% (w/v) of NaCl in the sample. Considering an extraction/desorption cycle using the 96-well plate system, the sample preparation time was 1.7 min per sample, which contributes to the high-throughput of the method proposed. The analytical parameters of merit were determined and satisfactory results were achieved, including limits of detection ranging from 0.3 μg L^-1 for estradiol to 3 μg L^-1 for estrone, while limits of quantification varied from 1 μg L^-1 for estradiol to 10 μg L^-1 for estrone. The correlation coefficients ranged from 0.9947 for estrone to 0.9999 for estriol. The accuracy and intra-assay and intermediate precisions (RSD) were evaluated through extractions in diluted urine samples (40-fold) spiked with each analyte (1, 200 and 400 μg L^-1 for E3; 0.1, 200 and 400 μg L^-1 for E2; 0.5, 200 and 400 μg L^-1 for EE2 and 10, 200 and 400 μg L^-1 for E1). The relative recoveries (n = 3) ranged from 71 to 105%, intra-assay precision (n = 3) varied from 1 to 17% and intermediate precision (n = 9) ranged from 2 to 19%. The method developed can be successfully used for the quantification of estrogens in human urine samples.

Oriented ZnO nanoflakes on nickel-titanium alloy fibers for solid-phase microextraction of polychlorinated biphenyls and polycyclic aromatic hydrocarbons

ZnO nanoflakes (ZnONFs) were electrochemically grown on a nickel-titanium alloy (NiTi) wire for use in solid-phase microextraction. Prior to the growth of ZnONFs, the NiTi wire was hydrothermally treated for in-situ growth of TiO₂/NiO nanoflakes as a seeding base. The applied potential was used to control the dimensions of vertically oriented hexagonal ZnONFs. After annealing at 600 °C, the resulting fiber display fairly selective affinity for polychlorinated biphenyls (PCBs) and polycyclic aromatic hydrocarbons. The fibers were applied to the preconcentration of PCBs which then were quantified by HPLC with UV detection. Compared to commercial polydimethylsiloxane coatings, the new coating displays high extraction capability, rapid extraction kinetics and superior cycling stability. This is assumed to be due to its high surface-to-volume ratio, double-sided open access structure, and enhanced structural stability. The assay excels by (a) a wide analytical range (0.10 to 200 μg L^-1 of PCBs), (b) low limits of detection (20-17 ng L^-1), and (c) low standard deviations for the single fiber repeatability (<9.8%) and for the fiber-to-fiber reproducibility (<7.5%). Satisfactory accuracy and precision were achieved when PCBs were determined by this method in spiked rain water, river water and wastewater samples. Graphical abstract ZnO nanoflakes were fabricated on a superelastic nickel-titanium alloy wire in desired orientation with enhanced extraction capability and good extraction selectivity. The fabricated fiber was suitable for the determination of PCBs in environmental water samples.

Dispersive liquid–liquid microextraction using magnetic room temperature ionic liquid for extraction of ultra-trace amounts of parabens

In this work, a dispersive liquid–liquid microextraction method using methyltrioctylammonium tetrachloroferrate was employed for the extraction of ultratrace amounts of parabens in water, beer and beverage samples.

A low-cost biosorbent-based coating for the highly sensitive determination of organochlorine pesticides by solid-phase microextraction and gas chromatography-electron capture detection

In this study, an environmentally friendly and low-cost biosorbent coating was evaluated, for the first time, as the extraction phase for solid-phase microextraction (SPME) supported on a nitinol alloy. The characterization of the new fiber was performed by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA) and scanning electron microscopy (SEM). The applicability of the biosorbent-based fiber in the determination of δ-hexachlorocyclohexane, aldrin, heptachlor epoxide, α-endosulfan, endrin and 4,4'-DDD in water samples was verified, with separation/detection by gas chromatography coupled to electron capture detection (GC-ECD). The influencing parameters (temperature, extraction time and ionic strength) were optimized simultaneously using a central composite design. The optimum conditions were: extraction time of 80min at 80°C and sodium chloride concentration of 15% (w/v). Satisfactory analytical performance was achieved with limits of detection (LOD) between 0.19 and 0.71ngL^-1 and limits of quantification (LOQ) between 0.65 and 2.38ngL^-1. The relative recoveries for the analytes were determined using river and lake water samples spiked at different concentrations and ranged from 60% for α-endosulfan to 113% for δ-hexachlorocyclohexane, with relative standard deviations (RSD) lower than 21%. The fiber-to-fiber reproducibility (n=3) was also evaluated and the RSD was lower than 14%. The extraction efficiency obtained for the proposed biosorbent coating was compared to a commercially available DVB/Car/PDMS coating. The proposed fiber provided very promising results, including LODs at the level of parts per trillion and highly satisfactory thermal and mechanical stability.

Development of a New Microextraction Fiber Combined to On-Line Sample Stacking Capillary Electrophoresis UV Detection for Acidic Drugs Determination in Real Water Samples

A new analytical method coupling a (off-line) solid-phase microextraction with an on-line capillary electrophoresis (CE) sample enrichment technique was developed for the analysis of ketoprofen, naproxen and clofibric acid from water samples, which are known as contaminants of emerging concern in aquatic environments. New solid-phase microextraction fibers based on physical coupling of chromatographic supports onto epoxy glue coated needle were studied for the off-line preconcentration of these micropollutants. Identification and quantification of such acidic drugs were done by capillary zone electrophoresis (CZE) using ultraviolet diode array detection (DAD). Further enhancement of concentration sensitivity detection was achieved by on-line CE “acetonitrile stacking” preconcentration technique. Among the eight chromatographic supports investigated, Porapak Q sorbent showed higher extraction and preconcentration capacities. The screening of parameters that influence the microextraction process was carried out using a two-level fractional factorial. Optimization of the most relevant parameters was then done through a surface response three-factor Box-Behnken design. The limits of detection and limits of quantification for the three drugs ranged between 0.96 and 1.27 µg∙L⁻¹ and 2.91 and 3.86 µg∙L⁻¹, respectively. Recovery yields of approximately 95 to 104% were measured. The developed method is simple, precise, accurate, and allows quantification of residues of these micropollutants in Genil River water samples using inexpensive fibers.

Review of geometries and coating materials in solid phase microextraction: Opportunities, limitations, and future perspectives

The development of new support and geometries of solid phase microextraction (SPME), including metal fiber assemblies, coated-tip, and thin film microextraction (TFME) (i.e. self-supported, fabric and blade supported), as well as their effects on diffusion and extraction rate of analytes were discussed in the current review. Application of main techniques widely used for preparation of a variety of coating materials of SPME, including sol-gel technique, electrochemical and electrospinning methods as well as the available commercial coatings, were presented. Advantages and limitations of each technique from several aspects, such as range of application, biocompatibility, availability in different geometrical configurations, method of preparation, incorporation of various materials to tune the coating properties, and thermal and physical stability, were also investigated. Future perspectives of each technique to improve the efficiency and stability of the coatings were also summarized. Some interesting materials including ionic liquids (ILs), metal organic frameworks (MOFs) and particle loaded coatings were briefly presented.

Determination of piperidinium ionic liquid cations in environmental water samples by solid phase extraction and hydrophilic interaction liquid chromatography

This paper presents a novel analytical method for the determination of piperidinium ionic liquid cations in environmental water by hydrophilic interaction liquid chromatography and solid-phase extraction technology. The left standing, centrifuged and filtered river water samples were first purified and concentrated through the C18 solid phase extraction column, and eluted with 0.02mol/L hydrochloric acid prepared in methanol and deionized water (80/20, v/v). Then the eluents were analyzed by a hydrophilic column combined with 0.8mmol/L 1-propyl-3-methyl imidazolium tetrafluoroborate aqueous solution/acetonitrile (40/60, v/v) as the mobile phase and indirect ultraviolet detection. The detection limits of piperidinium cations were less than 0.4mg/L. The relative standard deviations were less than 0.6%. The method has been successfully applied to the determination of piperidinium cations in Songhua River water samples. Recoveries were 80.0%-98.3%. This research may provide a reference for studying the environmental effect of ionic liquids.