Experimental composites containing quaternary ammonium methacrylates reduce demineralization at enamel-restoration margins after cariogenic challenge

Evaluation of a multifunctional orthodontic adhesive incorporating zinc oxide quantum dots

INTRODUCTION

The objective of this study was to further evaluate the long-term antibiofilm and fluorescence properties as well as enamel demineralization prevention ability, removal efficiency, and biocompatibility of an orthodontic adhesive modified with zinc oxide quantum dots (ZnQDs).

METHODS

ZnQDs were synthesized and characterized by transmission electron microscope and fluorescence observation. Minimal inhibitory concentration and minimum bactericidal concentration of ZnQDs against Streptococcus mutans were evaluated. ZnQDs (20% by weight) were incorporated into Transbond XT adhesive paste to form the multifunctional orthodontic adhesive (quantum dots adhesive 20 [QDA20]). Long-term antibiofilm capability and fluorescence properties were evaluated after saliva storage aging. A biofilm demineralization model was constructed, and the enamel demineralization degree was evaluated by color analysis, Raman analysis and microcomputed tomography. Bracket bonding and debonding procedures were performed on a head simulator, and the effectiveness of adhesive removal was assessed. Subcutaneous tissue, blood, and organ compatibility assays were performed on a rat subcutaneous tissue implant model.

RESULTS

ZnQDs had a diameter of approximately 5 nm, and the minimal inhibitory concentration and minimum bactericidal concentration against S mutans were 0.32 and 1.25 mg/mL. ZnQDs showed long-lasting antibiofilm and fluorescent properties and could reduce the color change and mineral loss of enamel during the biofilm demineralization process. On the head simulator, QDA20 could help the operator remove adhesive more thoroughly without damaging enamel. Histologic analysis of subcutaneous tissue and organs, and blood analysis proved that QDA20 was well-biocompatible.

CONCLUSIONS

ZnQDs showed excellent antibiofilm and fluorescent properties and thus could be a multifunctional adhesive to overcome the 2 major challenges of enamel demineralization and difficulty in recognizing adhesives during fixed orthodontic treatment.

Regulating the surface charge and reactivity of cellulose through quaternized modification to achieve salt-free reactive dyeing process

Limited research exists on how the structure of quaternary ammonium salt (QAS) affects the electrostatic attraction and hydroxyl reactivity of cationic cotton, which strongly affects reactive dye adsorption, diffusion, and fixation. Thus, in our work, the effects of QAS structure on the electrostatic attraction, hydroxyl reactivity, and dyeing properties were investigated. The intensity at 402.5 eV (-N+(CH3)3) in the XPS rose from 34 % to 70 % as the QAS alkyl chain length increased from 4 to 18 carbon atoms, signifying an enhancement of the positive charge and electrostatic attraction between reactive dye and QAS modified cotton. However, molecular dynamic (MD) simulations of the QAS-modified cotton with octadecyl chains revealed that the reactive dye demonstrated slower molecular mobility compared to the untreated cotton. This is not conducive to the diffusion and fixation of reactive dyes. The QAS-modified cotton with hexyl chains not only alters the activity of hydroxyl at the 6th but also generates additional hydroxyl at the β-position that contributes to enhancing the improvement of fixation through Gaussian simulations. Therefore, cationic cotton treated with 60 g/L of (3-chloro-2-hydroxypropyl)-dimethyl-octadecylazanium chloride (CT-8) exhibits superior dye uptake levels (91.84 %), K/S values (13.10), and dye fixation percent (88.38 %).

Development and effect of orodispersible film incorporated with Biosilicate for remineralization of dental enamel subjected to cariogenic and erosive challenge

OBJECTIVES

The objective of this in vitro study was to assess the efficiency of incorporating Biosilicate particles (30 and 50 mg) into an experimental orodispersible film and its efficacy in the remineralization process of bovine dental enamel under cariogenic and erosive challenges.

METHODS

Ninety-nine intact incisors, devoid of cracks or fractures, yielding 198 samples (6 × 6 × 2 mm) via vestibular sectioning using a low-speed diamond disc under water cooling. After flattening the enamel surface with 600, 1200, and 2000 grit sandpaper, the samples were divided into two groups based on the challenges they underwent: cariogenic (0.1 M lactic acid at pH 5.0) or erosive (0.05 M citric acid solution at pH 2.3). Samples from each challenge were further categorized into 11 groups (n = 9) according to the duration of cariogenic (3, 7, and 14 days) or erosive (3, 7, and 10 days) challenge, along with positive control groups (fragments untreated with challenges and treated with different Biosilicate concentrations) and negative controls (fragments treated with artificial saliva for the same periods established for cariogenic and erosive challenges). Treatments with orodispersible films containing Biosilicate (30 and 50 mg) were administered for 2 min per day for 15 days.

RESULTS

The highest remineralizing potential was observed in samples treated with Biosilicate after 14 days of cariogenic challenge, irrespective of the concentration tested. For samples subjected to erosive challenge, erosion time did not affect Biosilicate's remineralizing potential.

CONCLUSION

Biosilicate shows promise in terms of remineralizing potential in enamel subjected to cariogenic challenge due to its ability to form hydroxycarbonapatite in mineralized tissues.

Novel bioactive nanospheres show effective antibacterial effect against multiple endodontic pathogens

Aim

The current study evaluated the antibacterial activity of a newly developed quaternary ammonium polymethacrylate (QAPM)-containing bioactive glasses (BGs) via a two-step method by our group, namely BGs-HAEMB, and explored its cytotoxicity and biocompatibility.

Methods

The antibacterial effects of the BGs-HAEMB against planktonic bacteria, bacterial biofilm formation, and experimental root canal biofilms of persistent pathogens (Enterococcus faecalis, Streptococcus sanguis and Porphyromonas endodontalis) associated with endodontic infection were evaluated in vitro by agar diffusion tests, direct contact tests and live/dead staining. The cytotoxicity and biocompatibility of BGs-HAEMB were evaluated by CCK-8 assays in vitro and a skin implantation model in vivo.

Results

Compared to three clinically used endodontic sealers (Endofill, AH Plus, and iRoot SP), BGs-HAEMB exhibited the relatively strongest antibacterial effect against E. faecalis, S. sanguis and P. endodontalis after sitting for 14 and 28 days (P < 0.01). SEM images and CLSM images also showed that for each tested bacteria, BGs-HAEMB killed the most microorganism among all the experimental groups, regardless of treatment for 7 days or 28 days (P < 0.05). Besides, the BGs-HAEMB-treated groups showed a relatively low cytotoxicity (RGRs ranging from 88.6% to 102.9%) after 1, 3, and 7 days of exposure. Meanwhile, after 28 days of implantation, the inflammatory grade in BGs-HAEMB treated group was assessed as Grade I, in which the average numbers of inflammatory cells (6.7 ± 2.1) were less than 25.

Conclusions

BGs-HAEMB exerted a long-term and stable antibacterial effect. The remarkable biocompatibility of BGs-HAEMB in vitro and in vivo confirmed its possible clinical application as a potential alternative in the development of the next generation of endodontic sealers.

Demineralization prevention with a new antibacterial restorative composite containing QASi nanoparticles: an in situ study

OBJECTIVES

To investigate whether a newly developed dental composite with quaternary ammonium silica dioxide (QASi) nanoparticles incorporated with other fillers into the restorative material demonstrates antibacterial activity by reducing enamel demineralization in an in situ gap model.

MATERIALS AND METHODS

Twenty subjects wearing a lower removable partial denture (RPD) with acrylic flanges on both sides of the mouth were recruited into the 4-week in situ study. The gap model consisted of an enamel slab placed next to a composite, separated by a 38-μm space. In the split-mouth design on one side of the RPD, the composite was the Nobio Infinix composite (Nobio Ltd., Kadima, Israel), and the contralateral side used a control composite. Each participant received enamel slabs from one tooth. The gap model was recessed into the RPD buccal flange, allowing microbial plaque to accumulate within the gap. After 4 weeks of continuous wearing, decalcification (∆Z mineral loss) of the enamel slabs adjacent to the gap was determined by cross-sectional microhardness testing in the laboratory.

RESULTS

The ∆Z for the antibacterial composite test side was 235±354 (mean±standard deviation [SD]; data reported from 17 participants) and statistically significantly lower compared to ∆Z of the control side (774±556; mean±SD) (paired t-test, P<0.0001; mean of test minus control -539 (SD=392), 95% confidence interval of difference: -741, -338).

CONCLUSIONS

This in situ clinical study showed that composites with QASi antibacterial particles significantly reduced demineralization in enamel adjacent to a 38-μm gap over a 4-week period in comparison to a conventional composite.

CLINICAL RELEVANCE

Composites with QASi nanoparticle technology have the potential to reduce the occurrence of secondary caries.

TRIAL REGISTRATION

ClinicalTrials.gov #NCT04059250.

Enamel Demineralization Resistance and Remineralization by Various Fluoride-Releasing Dental Restorative Materials

The aim of this study is to investigate the resistance of various fluoride-releasing restorative materials against the demineralization and remineralization of enamel surfaces, including those that have been recently introduced to the market. Three different fluoride-releasing restorative materials were considered: glass ionomer (FI), resin-modified glass ionomer (RL), and an alkasite restorative material (CN). The acid neutralization ability was investigated using pH measurement, and the concentrations of released fluoride and calcium ions were measured. Finally, the demineralization resistance and remineralization effects of enamel were observed using a microhardness tester and SEM. CN showed an initial substantial increase in pH followed by a steady increase, with values higher than those of the other groups (p < 0.05). All three groups released fluoride ions, and the CN group released more calcium ions than the other groups (p < 0.05). In the acid resistance test, from the microhardness and SEM images, the CN group showed effective resistance to demineralization. In the remineralization test, the microhardness results showed that the FI and CN groups recovered the microhardness from the values of the demineralized enamel surface (p < 0.05). This was confirmed by the SEM images from remineralization tests; the CN group showed a recovered demineralized surface when immersed in artificial saliva for 7 days. In conclusion, alkasite restorative material can be an effective material when used in cariogenic environments.

Thiourethane-functionalized fillers: biological properties and degradation resistance

This study determined the effect of thiourethane-functionalized fillers (TU) on the antimicrobial properties, cytotoxicity, degree of conversion (DC), water sorption (Wsp) and solubility (Wsl) of experimental composites. TU-modified fillers were added at different ratios in experimental composites: 0 (Control-TU0), 25% (TU25), 50% (TU50), 75% (TU75) and 100wt% (TU100). The antimicrobial properties were detected through the exhaustion test and counting of Streptococus mutans colonies for biofilm formation. Cytotoxicity to human gingival fibroblasts was evaluated in three different parameters: XTT (2,3-Bis-(2-Methoxy-4-Nitro-5-Sulfophenyl)-2H-Tetrazolium-5-Carboxanilide), NRU (Neutral Red Uptake assay) and CVDE (Crystal Violet Dye Exclusion test)) at the same cells. ELISA was used to measure the IL-6 and b-FGF biomarkers. DC was determined by Fourier-transformed infrared spectroscopy, while Wsp and Wsl by mass variations. Inhibitory capacity of biofilm formation was not observed for any material. All groups presented at least 70% of cell survival within the observed periods (24h and 7 days). Positive control (toxic) had high IL-6 values and low b-FGF values. No significant variations in DC, Wsp, and Wsl were observed among the experimental groups. The use of thiourethane did not present antimicrobial and cytotoxic activity and the tested materials presented equivalent properties to those conventionally used in dentistry.

Bibliometric Analysis of Literature Published on Antibacterial Dental Adhesive from 1996-2020

This study aimed to investigate the current state of research on antibacterial dental adhesives. The interest in this field can be drawn from an increasing number of scholarly works in this area. However, there is still a lack of quantitative measurement of this topic. The main aim of this study was to consolidate the research published on the antibacterial adhesive from 1996 to 2020 in Web of Science indexed journals. The bibliometric method, a quantitative study of investigating publishing trends and patterns, was used for this study. The result has shown that a gradual increase in research was found, whereby a substantial increase was observed from 2013. A total of 248 documents were published in 84 journals with total citations of 5107. The highly cited articles were published mainly in Q1 category journals. Most of the published articles were from the USA, China, and other developed countries; however, some developing countries contributed as well. The authorship pattern showed an interdisciplinary and collaborative approach among researchers. The thematic evaluation of keywords along with a three-factor analysis showed that 'antibacterial adhesives' and 'quaternary ammonium' have been used commonly. This bibliometric analysis can provide direction not only to researchers but also to funding organizations and policymakers.

Nanoparticles of Quaternary Ammonium Polyethylenimine Derivatives for Application in Dental Materials

Various quaternary ammonium polyethylenimine (QA-PEI) derivatives have been synthesized in order to obtain nanoparticles. Due to their antibacterial activity and non-toxicity towards mammalian cells, the QA-PEI nanoparticles have been tested extensively regarding potential applications as biocidal additives in various dental composite materials. Their impact has been examined mostly for dimethacrylate-based restorative materials; however, dental cements, root canal pastes, and orthodontic adhesives have also been tested. Results of those studies showed that the addition of small quantities of QA-PEI nanoparticles, from 0.5 to 2 wt.%, led to efficient and long-lasting antibacterial effects. However, it was also discovered that the intensity of the biocidal activity strongly depended on several chemical factors, including the degree of crosslinking, length of alkyl telomeric chains, degree of N-alkylation, degree of N-methylation, counterion type, and pH. Importantly, the presence of QA-PEI nanoparticles in the studied dental composites did not negatively impact the degree of conversion in the composite matrix, nor its mechanical properties. In this review, we summarized these features and functions in order to present QA-PEI nanoparticles as modern and promising additives for dental materials that can impart unique antibacterial characteristics without deteriorating the products' structures or mechanical properties.

Novel Nanocomposite Inhibiting Caries at the Enamel Restoration Margins in an In Vitro Saliva-Derived Biofilm Secondary Caries Model

Secondary caries often occurs at the tooth-composite margins. This study developed a novel bioactive composite containing DMAHDM (dimethylaminohexadecyl methacrylate) and NACP (nanoparticles of amorphous calcium phosphate), inhibiting caries at the enamel restoration margins in an in vitro saliva-derived biofilm secondary caries model for the first time. Four composites were tested: (1) Heliomolar nanocomposite, (2) 0% DMAHDM + 0% NACP, (3) 3% DMAHDM + 0% NACP, (D) 3% DMAHDM + 30% NACP. Saliva-derived biofilms were tested for antibacterial effects of the composites. Bovine enamel restorations were cultured with biofilms, Ca and P ion release of nanocomposite and enamel hardness at the enamel restoration margins was measured. Incorporation of DMAHDM and NACP into composite did not affect the mechanical properties (p > 0.05). The biofilms’ CFU (colony-forming units) were reduced by 2 logs via DMAHDM (p < 0.05). Ca and P ion release of the nanocomposite was increased at cariogenic low pH. Enamel hardness at the margins for DMAHDM group was 25% higher than control (p < 0.05). With DMAHDM + NACP, the enamel hardness was the greatest and about 50% higher than control (p < 0.05). Therefore, the novel composite containing DMAHDM and NACP was strongly antibacterial and inhibited enamel demineralization, resulting in enamel hardness at the margins under biofilms that approached the hardness of healthy enamel.

Ten Years of Micro-CT in Dentistry and Maxillofacial Surgery: A Literature Overview

Micro-computed tomography (micro-CT) is a consolidated imaging technology allowing non-destructive three-dimensional (3D) qualitative and quantitative analysis by the observation of microstructures with high resolution. This paper aims at delivering a structured overview of literature about studies performed using micro-CT in dentistry and maxillofacial surgery (MFS) by analyzing the entire set of articles to portray the state of the art of the last ten years of scientific publications on the topic. It draws the scenario focusing on biomaterials, in vitro and in/ex vivo applications, bone structure analysis, and tissue engineering. It confirms the relevance of the micro-CT analysis for traditional research applications and mainly in dentistry with respect to MFS. Possible developments are discussed in relation to the use of the micro-CT combined with other, traditional, and not, techniques and technologies, as the elaboration of 3D models based on micro-CT images and emerging numerical methods. Micro-CT results contribute effectively with whose ones obtained from other techniques in an integrated multimethod approach and for multidisciplinary studies, opening new possibilities and potential opportunities for the next decades of developments.

Structural stability of DHMAI antibacterial dental composite following in vitro biological aging

OBJECTIVE

To assess the impact of the quaternary ammonium antibacterial agent, Dimethyl-Hexadecyl-Methacryloxyethyl-Ammonium Iodide (DHMAI), on structural stability of an experimental resin composite after biological aging.

METHODS

Experimental resin composites containing 7.5% of DHMAI were incubated in a biological medium in the presence of a Streptococcus Mutans (SM) strain during 3 months. The physicochemical, mechanical, and thermal properties, before and after 3 months of aging, were evaluated using: Degree of Conversion (DC), Residual Functions (RF), Vitreous Transition (Tg), Thermal Expansion Coefficient (CTE) and thermal degradation using Fourier Transform Infrared Spectroscopy Analysis (FTIRATR), Differential Scanning Calorimetry (DSC), Thermo Mechanical analyses (TMA) and Thermo Gravimetric Analysis (TG).

RESULTS

Incorporation of DHAMI increased DC and decreased RF. After aging, DHMAI decreased and slowed RF release. Incorporation of 7.5% DHAMI provided significant modification of the thermal behavior (Tg and thermal degradation) but did not affect CTE. After aging, DHMAI enhanced the structural stability and improved resistance against biodegradation compared to the control composite.

SIGNIFICANCE

The development of an antibacterial dental composite based on DHMAI improved its physical, mechanical, and thermal behaviors, possibly enhancing dental composite longevity. Results suggest that DHMAI could be used in the composition of other bioactive dental materials.