Chlorobenzene levels, component distribution, and ambient severity in wastewater from five textile dyeing wastewater treatment plants

Determination of hazardous vapors from the thermal decomposition of organochlorinated silica xerogels with adsorptive properties

The incorporation of organic groups into sol-gel silica materials is known to have a noticeable impact on the properties and structure of the resulting xerogels due to the combination of the properties inherent to the organic fragments (functionality and flexibility) with the mechanical and structural stability of the inorganic matrix. However, the reduction of the inorganic content in the materials could be detrimental to their thermal stability properties, limiting the range of their potential applications. Therefore, this work aims to evaluate the thermal stability of hybrid inorganic-organic silica xerogels prepared from mixtures of tetraethoxysilane and organochlorinated triethoxysilane precursors. To this end, a series of four materials with a molar percentage of organochlorinated precursor fixed at 10%, but differing in the type of organic group (chloroalkyls varying in the alkyl-chain length and chlorophenyl), has been selected as model case study. The gases and vapors released during the thermal decomposition of the samples under N2 atmosphere have been analyzed and their components determined and quantified using a thermogravimetric analyzer coupled to a Fourier-transform infrared spectrophotometer and to a gas chromatography-mass spectrometry unit. These analyses have allowed to identify up to three different thermal events for the pyrolysis of the organochlorinated xerogel materials and to elucidate the reaction pathways associated with such processes. These mechanisms have been found to be strongly dependent on the specific nature of the organic group.

Reduction characteristic of chlorobenzene by a newly isolated Paenarthrobacter ureafaciens LY from a pharmaceutical wastewater treatment plant

A highly efficient chlorobenzene-degrading strain was isolated from the sludge of a sewage treatment plant associated with a pharmaceutical company. The strain exhibited a similarity of over 99.9% with multiple strains of Paenarthrobacter ureafaciens. Therefore, the strain was suggested to be P. ureafaciens LY. This novel strain exhibited a broad spectrum of pollutant degradation capabilities, effectively degrading chlorobenzene and other organic pollutants, such as 1, 2, 4-trichlorobenzene, phenol, and xylene. Moreover, P. ureafaciens LY co-metabolized mixtures of chlorobenzene with 1, 2, 4-trichlorobenzene or phenol. Evaluation of its degradation efficiency showed that it achieved an impressive degradation rate of 94.78% for chlorobenzene within 8 h. The Haldane-Andrews model was used to describe the growth of P. ureafaciens LY under specific pollutants and its concentrations, revealing a maximum specific growth rate (μmax ) of 0.33 h-1 . The isolation and characterization of P. ureafaciens LY, along with its ability to degrade chlorobenzene, provides valuable insights for the development of efficient and eco-friendly approaches to mitigate chlorobenzene contamination. Additionally, investigation of the degradation performance of the strain in the presence of other pollutants offers important information for understanding the complexities of co-metabolism in mixed-pollutant environments.

Homogeneous and heterogeneous atmospheric ozonolysis of chlorobenzene:Mechanism, kinetics and ecotoxicity assessment

The reactions between chlorobenzene(CB) and ozone have been studied comprehensively in this paper. Chlorobenzene is a commonly found chlorinated aromatic volatile organic compound(VOC), and its emission into the atmosphere can cause harm to the ecosystem and human health. The frequent occurrence of mineral particles from sandstorms exerts a significant influence on the atmospheric chemistry of the troposphere. Mineral particles are abundant in SiO2 and Al2O3 content. Therefore, we investigated the homogeneous and heterogeneous reaction processes of CB and ozone in the atmosphere by using density functional theory (DFT) method at the M06-2X/6-311++g(3df,2p)//M06-2X/6-31+g(d,p) level. The atmospheric fate, reaction rate and toxicity evaluation of CB ozonation were studied in the gas-phase section. Toxicity evaluation results showed that ozonation of CB could effectively reduce its toxicity. For the heterogeneous process, we simulated three types of SiO2 clusters and nine types of (Al2O3)n clusters, and studied the configurations of CB adsorbed on the cluster surfaces. We found that adsorption of CB on the SiO2 clusters was achieved through hydrogen bonding, while adsorption of CB on the Al2O3 clusters was achieved through both hydrogen bonding and metal bonding. The energy for CB adsorption on the (Al2O3)n cluster surface was higher than that for the SixOy(OH)z cluster surface, and both types of clusters exhibited efficient adsorption of CB. As the SixOy(OH)z clusters grew larger, the rates for the reactions between O3 and CB increased. CB travelled long distances along the Al2O3 clusters, leading to an extended influence range.

Pollutants in aquatic system: a frontier perspective of emerging threat and strategies to solve the crisis for safe drinking water

Water is an indispensable natural resource and is the most vital substance for the existence of life on earth. However, due to anthropogenic activities, it is being polluted at an alarming rate which has led to serious concern about water shortage across the world. Moreover, toxic contaminants released into water bodies from various industrial and domestic activities negatively affect aquatic and terrestrial organisms and cause serious diseases such as cancer, renal problems, gastroenteritis, diarrhea, and nausea in humans. Therefore, water treatments that can eliminate toxins are very crucial. Unfortunately, pollution treatment remains a difficulty when four broad considerations are taken into account: effectiveness, reusability, environmental friendliness, and affordability. In this situation, protecting water from contamination or creating affordable remedial techniques has become a serious issue. Although traditional wastewater treatment technologies have existed since antiquity, they are both expensive and inefficient. Nowadays, advanced sustainable technical approaches are being created to replace traditional wastewater treatment processes. The present study reviews the sources, toxicity, and possible remediation techniques of the water contaminants.

Current status and future challenges of chlorobenzenes pollution in soil and groundwater (CBsPSG) in the twenty-first century: a bibliometric analysis

The global industrial structure had undertaken significant changes since the twenty-first century, making a severe problem of chlorobenzene pollution in soil and groundwater (CBsPSG). CBsPSG receives increasing attention due to the high toxicity, persistence, and bioaccumulation of chlorobenzenes. To date, despite the gravity of this issue, no bibliometric analysis (BA) of CBsPSG does exist. This study fills up the gap by conducting a BA of 395 articles related to CBsPSG from the Web of Science Core Collection database using CiteSpace. Based on a comprehensive analysis of various aspects, including time-related, related disciplines, keywords, journal contribution, author productivity, and institute and country distribution, the status, development, and hotspots of research in the field were shown visually and statistically. Moreover, this study has also delved into the environmental behavior and remediation techniques of CBsPSG. In addition, four challenges (unequal research development, insufficient cooperation, deeply mechanism research, and developing new technologies) have been identified, and corresponding suggestions have been proposed for the future development of research in the field. Afterwards, the limitations of BA were discussed. This work provides a powerful insight into CBsPSG, enabling to quickly identify the hotspot and direction of future studies by relevant researchers.

SBBGR technology for reducing waste sludge production during plastic recycling process: Assessment of potential increase in sludge hazardousness

Sludge production in the wastewater treatment sector is consistently increasing and represents a critical environmental and economic issue. This study evaluated an unconventional approach for treating wastewater generated from the cleaning of non-hazardous plastic solid waste during the plastic recycling process. The proposed scheme was based on sequencing batch biofilter granular reactor (SBBGR) technology, which was compared with the activated sludge-based treatment currently in operation. These treatment technologies were compared regarding sludge quality, specific sludge production, and effluent quality to highlight whether the reduced sludge production shown by SBBGR corresponded to an increase in the concentration of hazardous compounds in the sludge. The SBBGR technology showed remarkable removal efficiencies (TSS, VSS, and NH₃ > 99 %; COD >90 %; TN and TP > 80 %) and a sludge production six-fold lower than the conventional plant (in terms of kgTSS/kg COD_removed). Biomass from the SBBGR did not show a significant accumulation of organic micropollutants (i.e., long-chain hydrocarbons, chlorinated pesticides and chlorobenzenes, PCB, PCDD/F, PAH, chlorinated and brominated aliphatic compounds, and aromatic solvents), whereas a certain accumulation of heavy metals was observed. Furthermore, an initial attempt to compare the operating costs of the two treatment approaches revealed that the SBBGR technology would provide 38 % savings.

Degradation behaviors and accumulative effects of coexisting chlorobenzene congeners on the dechlorination of hexachlorobenzene in soil by nanoscale zero-valent iron

It is well known that many chlorinated organic pollutants can be dechlorinated by nanoscale zero-valent iron. However, in the real chlorinated organic compounds contaminated soil, the congeners of high- and low-chlorinated isomer often coexist and their dechlorination behaviors are poorly known, such as hexachlorobenzene (HCB). In this work, the degradation behaviors of three coexisting chlorobenzene congeners pentachlorobenzene (PeCB), 1,2,4,5-tetrachlorobenzene (1,2,4,5-TeCB) and 1,2,4-trichlorobenzene (1,2,4-TCB) and the influence of initial pH and reaction temperature on the dechlorination of HCB in HCB-contaminated soil by nanoscale zero-valent iron were studied. The amount and extent of accumulated coexisting chlorobenzenes was analyzed under different environmental conditions. The results indicate that nanoscale zero-valent iron can improve the degradation efficiency of highly toxic chlorinated benzenes and reduce the accumulative effects of highly toxic chlorinated benzenes on dechlorination of HCB. The accumulative effects of three coexisting chlorobenzene congeners on the dechlorination of HCB were ranked as follows: 1,2,4-TCB > 1,2,4,5-TeCB > PeCB.

A novel iron molybdate photocatalyst with heterojunction-like band gap structure for organic pollutant degradation by activation of persulfate under simulated sunlight irradiation

Advanced oxidation processes (AOPs) applied to wastewater treatment have become increasingly well developed and the ability of a single technology to remove difficult organic pollutants is limited. One of the main limiting factors is the insufficient variety and quantity of active species generated during the reaction process and catalyst failure. The coupling of the two methods is a practical and effective approach. In this study, different types of semiconductor persulfate (PS) activators, iron molybdate nanoparticles (I-FeMoO₄, II-FeMoO₄, and III-FeMoO₄), were synthesized by simple solvothermal and calcination methods and applied to photo-assisted activation of PS systems. In addition, the relationship between the intrinsic physicochemical and optoelectronic properties of FeMoO₄ and the catalytic degradation performance was revealed by a series of characterization tools, and the dominant catalysts were screened. At an unadjusted pH of 4.86, 0.6 g L^-1 of PS and 0.4 g L^-1 of I-FeMoO₄ could achieve efficient degradation of several difficult organic dye contaminants (rhodamine b (Rh B), methylene blue (MB), malachite green (MG), methyl orange (MO), and tartrazine (TTZ)) and other antibiotic contaminants (sulfamethoxazole (SMX), tetracycline (TC), norfloxacin (NOR), and carbamazepine (CBZ)) within 5-60 min. Possible degradation mechanisms in the I-FeMoO₄/PS/Light reaction system were suggested by radical trapping experiments and electron paramagnetic resonance (EPR) tests. Recovery tests demonstrated that I-FeMoO₄ has good recoverable stability and did not cause secondary pollution. Finally, our study provided a new perspective on the application of coupled wastewater treatment technologies in the practical treatment of organic wastewater.

Quantitative acquisition of differential absorption cross sections of chlorobenzenes at different temperatures

Chlorobenzene is considered an essential organic synthesis intermediate and a precursor for the generation of persistent organic compounds in the waste disposal process, for which accurate detection of gaseous chlorobenzene can further help understand and control various chemical processes and effectively reduce pollution. Differential optical absorption spectroscopy is a reliable online method for detecting gaseous chlorobenzenes. It is crucial to investigate the effect of temperature on the optical absorption of the chlorobenzenes to quantify chlorobenzenes more precisely at various temperatures. A method to fix the effect of temperature variation on absorption spectra of chlorobenzene is initially proposed in this study, and it gave accurate concentrations. The proposed method can effectively improve the accuracy of chlorobenzene concentration measurements with an inverse concentration deviation of 3.2 % or less. The differential absorption cross sections at various temperatures are studied to understand how chlorobenzene absorption cross sections vary with temperature. Such a study is also helpful in reducing the concentration inversion errors induced by the variation of absorption cross sections of chlorobenzene with temperature. A novel method of introducing the binary function of the differential absorption cross sections with respect to wavelength and temperature is also proposed. The fitting of the binary function is done by downscaling functions at fixed wavelength and fixed temperature,respectively. Both fitting approaches obtained continuous differential absorption cross sections in the 201-220 nm wavelength band and 288-473 K temperature range, along with less than 2.74 % deviation in the concentration inversion measurements. Finally,based on the temperature specificity of the shape of the differential absorption cross sections,we developed another method using differential absorption spectroscopy for the simultaneous measurement of temperature and concentration, with a temperature prediction error of less than 1.89 %. This method is favorable to the applications of differential absorption spectroscopy in simultaneous measurement of temperature and concentration.

Chemical fingerprinting of organic micropollutants in different industrial treated wastewater effluents and their effluent-receiving river

Industry wastewater is considered one of the worst polluters of our precious water ecologies. However, the types of pollutants present in wastewater from industrial wastewater treatment plants (IWTPs) are still unclear. In this study, a simple and effective chemical fingerprinting method for checking the source-sink relationships among different industrial wastewaters and their effluent-receiving river was established. 107, 228, 155, and 337 chemicals were screened out in wastewater from electronics, steel, textile, and printing and dyeing plants, respectively. Chemical fingerprinting of the detected chemicals was performed, and results showed that aromatic compounds were the most prevalent among the pollutant categories (i.e., 56, 189, and 168 in electronics, iron and steel, and printing and dyeing plants, respectively). The traceability analysis of the chemicals selected in the effluent determined the characteristic pollutants of different industrial enterprises. Sixty-eight compounds were identified as the characteristic pollutants in the different process stages of wastewater of the four IWTPs. Of the 84 effluent-receiving river water signature pollutants, 47.6% (n = 40) were also detected in the effluent from the four IWTPs. Effective screening of organic pollutants in industrial wastewater and determining their sources will help accelerate the improvement of industrial wastewater treatment technology.

The Separation of Chlorobenzene Compounds from Environmental Water Using a Magnetic Molecularly Imprinted Chitosan Membrane

In this work, a magnetic molecularly imprinted chitosan membrane (MMICM) was synthesized for the extraction of chlorobenzene compounds in environmental water using the membrane separation method. The optimal extraction amount for chlorobenzene (9.64 mg·L⁻¹) was found to be a 1:2 solid to liquid ratio, with a 20 min extraction time and 35 °C extraction temperature. This method proved to be successfully applied for the separation and trace quantification of chlorobenzene compounds in environmental water, with the limit of detection (LOD) (0.0016–0.057 ng·L⁻¹), limit of quantification (LOQ) (0.0026–0.098 ng·L⁻¹), and the recoveries ranging (89.02–106.97%).

Occurrence, source, and ecological risk assessment of organochlorine pesticides and polychlorinated biphenyls in the water-sediment system of Hangzhou Bay and East China Sea

The pollution characteristics, potential sources, and potential ecological risk of organochlorine pesticides (OCPs) and polychlorinated biphenyls (PCBs) were investigated in the Hangzhou Bay (HZB) and East China Sea (ECS). Total OCPs concentration ranged from 2.62 to 102.07 ng/L and 4.41 to 75.79 μg/kg in the seawater and sediment samples, with PCBs concentration in the range of 0.40-51.75 ng/L and 0.80-45.54 μg/kg, respectively. The OCPs were positively correlated with nutrients, whereas PCBs presented a negative correlation. The newly imported dichlorodiphenyltrichloroethane (DDT) in HZB is mainly the mixing of technical DDT and dicofol sources. The PCB source composition is more likely related to the mixture of Kanechlor 300, 400, Aroclor 1016, 1242, and Aroclor 1248. Risk assessment results indicate that OCPs posed low risk in seawater. The potential risk of DDTs in the sediments is a cause of concern.

Effect of Chronic Exposure to Textile Wastewater Treatment Plant Effluents on Growth Performance, Oxidative Stress, and Intestinal Microbiota in Adult Zebrafish (Danio rerio)

The ever-increasing production and processing of textiles will lead to greater risks of releasing pollutants into the environment. Textile wastewater treatment plants (TWTPs) effluent are an important source of persistent toxic pollutants in receiving water bodies. The effects of specific pollutants on organisms are usually studied under laboratory conditions, and therefore, comprehensive results are not obtained regarding the chronic combined effects of pollutants under aquatic environmental conditions. Thus, this study aimed to determine the combined effects of TWTP effluents on the growth performance, oxidative stress, inflammatory response, and intestinal microbiota of adult zebrafish (Danio rerio). Exposure to TWTP effluents significantly inhibited growth, exacerbated the condition factor, and increased the mortality of adult zebrafish. Moreover, markedly decreases were observed in the activities of antioxidant enzymes, such as CAT, GSH, GSH-Px, MDA, SOD, and T-AOC, mostly in the intestine and muscle tissues of zebrafish after 1 and 4 months of exposure. In addition, the results demonstrated that TWTP effluent exposure affected the intestinal microbial community composition and decreased community diversity. Slight changes were found in the relative abundance of probiotic Lactobacillus, Akkermansia, and Lactococcus in zebrafish guts after chronic TWTP effluent exposure. The chronic toxic effects of slight increases in opportunistic pathogens, such as Mycoplasma, Stenotrophomonas, and Vibrio, deserve further attention. Our results reveal that TWTP effluent exposure poses potential health risks to aquatic organisms through growth inhibition, oxidative stress impairment of the intestine and muscles, and intestinal microbial community alterations.

Adsorption mechanisms of chlorobenzenes and trifluralin on primary polyethylene microplastics in the aquatic environment

Microplastics are ubiquitous in aqueous media, and the importance of considering their impact on the behaviour of other compounds in water has often been highlighted. This work thus investigates the adsorption mechanism of six priority substances (as defined by European Union legislation: trichlorobenzenes (1,2,3-TeCB, 1,3,5-TeCB, 1,2,4-TeCB), pentachlorobenzene (PeCB), hexachlorobenzene (HeCB), and trifluralin (TFL)) on primary polyethylene (PE) microplastics (polyethylene standard and polyethylene microparticles isolated from two personal care products) in Danube river water and a synthetic matrix. The maximum adsorbed amounts of the compounds investigated on PEs ranged from 227 μg/g for 1,2,3-TeCB to 333 μg/g for TFL. Equilibrium data was analysed using five isotherm models, with the best fit being described by the Langmuir model and the Dubinin-Radushkevich model indicating chemisorption as the likely sorption mechanism. In general, the Langmuir model showed that the investigated compounds will be better adsorbed on PEs in real river water, with the exception of 1,3,5-TeCB on all studied PEs, where the model predicts better sorption in the synthetic matrix. Compound characteristics and the polymer properties were the most important factors affecting the sorption process, while a significant matrix effect was also observed on PE behaviour. The fact that polyethylene particles derived from personal care products showed greater adsorption capacities than virgin PE demonstrates the necessity of investigating real-world PE samples when assessing the potential impact of MPs in the environment.

Comprehensive insights into core microbial assemblages in activated sludge exposed to textile-dyeing wastewater stress

Microorganisms in activated sludge are widely recognized for their roles in wastewater treatment. However, previous studies were mainly concerned with the diversity and driving factors of microbial communities within domestic wastewater treatment, and those of domestic wastewater treatment systems mixed with industrial wastewater are poorly understood. In this research, three different full-scale aerobic activated sludge (AS) wastewater treatment systems fed with municipal, textile-dyeing, and mixed wastewater, respectively, were monitored over the operation course of three months. 16S rRNA amplicon sequencing analysis revealed that the microbial communities in textile-dyeing wastewater activated sludge (AS) exhibited significantly lower richness and diversity (p < 0.01, Adonis) compared to those fed with municipal wastewater. In contrast, textile-dyeing derived AS selectively enriched microbial taxa with aromatic degradation and denitrification potentials. Further, FARPROTAX and metabolomics indicated the inhibition of 72.5% metabolic functions (p < 0.01) in AS from the system fed with textile-dyeing wastewater, including the pathways of pentose phosphate metabolism, purine metabolism, and glycerophospholipid metabolism. Overall, this study corroborates textile-dyeing wastewater is a novel microbial niche and could suppress sludge performance by inhibiting microbial activity and metabolism, raising concerns on AS-based systems for industrial wastewater treatment.

Sublethal Effect Concentrations for Nonpolar Narcosis in the Zebrafish Embryo

Nonpolar narcosis, also known as baseline toxicity, has been described as the minimal toxicity that an organic chemical may elicit based on its lipophilicity. Although lethal effects of narcosis-inducing chemicals (NICs) have been thoroughly investigated, knowledge of sublethal effects is still very limited. We investigated the effects of 3 well-known NICs (phenanthrene, 1,3,5-trichlorobenzene, and pentachlorobenzene) on a variety of organismal endpoints (malformations, swim bladder inflation, respiration, heart rate, swimming activity, and turning angles), which can be plausibly linked to narcosis in zebrafish embryos. Baseline toxicity recorded as mortality is typically observed in similar exposure ranges in a wide variety of species including fish, corresponding to a chemical activity range between 0.01 and 0.1. In the present study, we found that sublethal effects occurred at concentrations approximately 5 times below lethal concentrations. Altered swimming activity and impaired swim bladder inflation were the most sensitive endpoints occurring at exposure levels below the generally accepted threshold for baseline toxicity for 2 out of 3 compounds. Overall, most effective exposure levels across the sublethal endpoints and compounds did fall within the range typically associated with baseline toxicity, and deviations were generally limited to a factor 10. Although there could be benefit in adding sublethal endpoints to toxicity tests, such as the fish embryo acute toxicity (FET) test, based on the present sublethal endpoints and available evidence from our and other studies, the underestimation of toxicity as a result of the sole assessment of mortality as an endpoint in an FET test may be limited for narcosis. Environ Toxicol Chem 2021;40:2802-2812. © 2021 SETAC.

Study on Start-Up Membraneless Anaerobic Baffled Reactor Coupled with Microbial Fuel Cell for Dye Wastewater Treatment

In this study, the antitoxicity performance of the traditional anaerobic baffled reactor (ABR) and the newly constructed membraneless anaerobic baffled reactor coupled with microbial fuel cell (ABR-MFC) was compared for the treatment of simulated printing and dyeing wastewater under the same hydraulic residence time. The sludge performances of ABR-MFC and ABR were evaluated on the dye removal rate, extracellular polymer (EPS) content, sludge particle size, methane yield, and the surface morphology of granular sludge. It was found that the maximum power density of the ABR-MFC reactor reached 1226.43 mW/m³, indicating that the coupled system has a good power generation capacity. The concentration of the EPS in the ABR-MFC reactor was about 3 times that in the ABR, which could be the result of the larger average particle size of sludge in the ABR-MFC reactor than in the ABR. The dye removal rate of the ABR-MFC reactor (91.71%) was higher than that of the ABR (1.49%). The methane production and microbial species in the ABR-MFC system were higher than those in the ABR. Overall, the MFC embedded in the ABR can effectively increase the resistance of the reactor, promote the formation of granular sludge, and improve the performance of the reactor for wastewater treatment.

Nitrogen-doped porous biochar derived from marine algae for efficient solid-phase microextraction of chlorobenzenes from aqueous solution

Nitrogen-doped porous biochar (NPB) with a large specific surface area, wide pore size distribution, graphitized structure, nitrogen doping, and hydrophobicity was fabricated by high-temperature modification of algal biochar with potassium carbonate. This NPB was then uniformly coated on stainless steel wire as a novel solid-phase microextraction (SPME) fiber. The extraction efficiency of NPB-coated fiber for seven chlorobenzenes (CBs) was excellent; it was 1.0-112.2 times higher than that of commercial SPME fibers. A trace determination method was developed for seven CBs in water with the optimized extraction conditions by NPB-coated fiber and gas chromatography-electron capture detector, which showed wide linear ranges (1-1000 ng L^-1), low detection limits (0.007-0.079 ng L^-1), great repeatability (2.5-6.5% for intra-day, and 3.1-6.8% for inter-day), and excellent reproducibility (3.5-6.3%, n = 5). The practicality of the developed method was evaluated using real water samples and showed great recoveries (89.55-105.19%). This study showed that low-cost biomass wastes could be converted to advanced biochar materials by a facile method, and displayed excellent performance in SPME applications.

Integrated Membrane-Electrocoagulation System for Removal of Celestine Blue Dyes in Wastewater

The textile industry provides for the needs of people especially in apparel and household items. The industry also discharges dye-containing wastewater that is typically challenging to treat. Despite the application of the biological and chemical treatments for the treatment of textile wastewater, these methods have their own drawbacks such as non-environment friendly, high cost and energy intensive. This research investigates the efficiency of the celestine blue dye removal from simulated textile wastewater by electrocoagulation (EC) method using iron (Fe) electrodes through an electrolytic cell, integrated with nylon 6,6 nanofiber (NF) membrane filtration for the separation of the flocculants from aqueous water. Based on the results, the integrated system achieves a high dye removal efficiency of 79.4%, by using 1000 ppm of sodium chloride as the electrolyte and 2 V of voltage at a constant pH of 7 and 10 ppm celestine blue dye solution, compared to the standalone EC method in which only 43.2% removal was achieved. Atomic absorption spectroscopy analysis was used to identify the traces of iron in the residual EC solution confirming the absence of iron. The EC-integrated membrane system thus shows superior performance compared to the conventional method whereby an additional 10–30% of dye was removed at 1 V and 2 V using similar energy consumptions.

Fe3O4/PVDF catalytic membrane treatment organic wastewater with simultaneously improved permeability, catalytic property and anti-fouling

Fe₃O₄/Polyvinylidene fluoride (PVDF) three-channel hollow fiber catalytic membrane was successfully fabricated via non-solvent induced phase inversion and used for organic wastewater degradation in this work. The effects of Fe₃O₄ nanoparticles addition on the surface and cross-section morphologies, hydrophilicity and thermal properties of the catalytic membrane were characterized by the field emission scanning electron microscopy (SEM), water contact angle and thermogravimetric analysis (TGA), respectively. The obtained catalytic membrane exhibited good hydrophilicity, a high pure water flux of 175.8 L m^-2 h^-1 and a high removal of methylene blue (up to 97.6%) with Fenton catalytic reaction. Meanwhile, the catalytic membrane shows excellent anti-fouling property due to the presence of Fenton reaction. Our results show that Fe₃O₄/PVDF three-channel hollow fiber catalytic membrane was a promising alternative for the degradation of organic contaminants.