Dose reduction in maxillofacial imaging using low dose Cone Beam CT

Investigation of the effect of thyroid collar, radiation safety glasses, and lead apron on radiation dose in cone beam CT

OBJECTIVES

Due to the increasing use of cone-beam CT (CBCT) in dentistry and considering the effects of radiation on radiosensitive organs, the aim of this study was to investigate the effect of shielding on absorbed dose of eyes, thyroid, and breasts in scans conducted with different parameters using 2 different fields of view (FOV).

METHODS

Dose measurements were calculated on a tissue-equivalent female phantom by repeating each scanning parameter 3 times and placing at least 2 thermoluminescent dosimeters (TLD) on each organ, with the averages then taken. The same CBCT scans were performed in 2 different FOV with shielding including thyroid collar, radiation safety glasses, and lead apron and without shielding. The differences between them were analysed statistically. Descriptive statistics and the Wilcoxon test were used for data analysis.

RESULTS

The difference between measurements with and without shielding was statistically significant for all scans (P < .001). The dose reduction associated with the use of shielding ranged from 26.81% to 52.95%. The dose related to the FOV has shown a significant increase, ranging from 8.30% to 623.54%, due to both the variation in the area affected by the primary beam on the organs and changes in the amount of radiation.

CONCLUSION

There are significant differences in the absorbed dose depending on shielding and FOV usage. Therefore, the CBCT imaging protocol should be optimized by the operator, and special attention should be paid to the use of thyroid collars and radiation safety glasses, considering their effects on image quality.

An Evaluation of the Relationship Between the Mesiobuccal Canal Configuration, the Interorifice Distance, and the Root Lengths of the Permanent Maxillary First Molars with Cone Beam Computed Tomography

This study aimed to investigate the relationship between the mesiobuccal root canal configuration (MB RCC), the interorifice distance (IOD) and the corresponding root and other root lengths of the permanent maxillary first molars; Methods: Cone beam computed tomography (CBCT) images were acquired between 2020 and 2023 for different purposes unrelated to this study. Overall, 1550 CBCT images were retrospectively evaluated. A dentomaxillofacial radiologist with 15 years of experience evaluated the CBCT images and performed the measurements; Results: According to the MB RCC, there was no statistically significant difference between the Vertucci type II and Vertucci type IV groups in terms of the mean age and sex distribution (p = 0.694 and p = 0.273). There was no statistically significant difference in the IOD between the MB RCC groups (p = 0.755). Moreover, according to the MB RCC, there was no statistically significant difference between the Vertucci type II and Vertucci type IV groups in terms of the mesiobuccal, distobuccal, palatinal, and mean root lengths (p > 0.05); Conclusions: There was no association between the IOD and the type of RCC in the maxillary first molars. New studies conducted by collecting data from different centers to explore the different morphological features of maxillary first molars and detect their anatomical differences will provide more reliable and accurate results.

Comparison of 96-kV and 120-kV cone-beam CT for the assessment of cochlear implants

BACKGROUND

To compare the diagnostic value of 120-kV with conventional 96-kV Cone-Beam CT (CBCT) of the temporal bone after cochlear implant (CI) surgery.

METHODS

This retrospective study included CBCT scans after CI surgery between 06/17 and 01/18. CBCT allowed examinations with 96-kV or 120-kV; other parameters were the same. Two radiologists independently evaluated following criteria on 5-point Likert scales: osseous spiral lamina, inner and outer cochlear wall, semi-circular canals, mastoid trabecular structure, overall image quality, metal and motion artefacts, depiction of intracochlear electrode position and visualisation of single electrode contacts. Effective radiation dose was assessed.

RESULTS

Seventy-five patients (females, n = 39 [52.0%], mean age, 55.8 ± 16.5 years) were scanned with 96-kV (n = 32, 42.7%) and 120-kV (n = 43, 57.3%) protocols including CI models from three vendors (vendor A n = 7; vendor B n = 43; vendor C n = 25). Overall image quality, depiction of anatomical structures, and electrode position were rated significantly better in 120-kV images compared to 96-kV (all p < = 0.018). Anatomical structures and electrode position were rated significantly better in 120-kV CBCT for CI models from vendor A and C, while 120-kV did not provide improved image quality in CI models from vendor B. Radiation doses were significantly higher for 120-kV scans compared to 96-kV (0.15 vs. 0.08 mSv, p < 0.001).

CONCLUSIONS

120-kV and 96-kV CBCT provide good diagnostic images for the postoperative CI evaluation. While 120-kV showed improved depiction of temporal bone and CI electrode position compared to 96-kV in most CI models, the 120-kV protocol should be chosen wisely due to a substantially higher radiation exposure.

Determination of Mouth Width for Facial Reconstruction Based on Statistical Regression Model

INTRODUCTION

It is important to generate predictable statistical models by increasing the number of variables on the human skeletal and soft tissue structures on the face to increase the accuracy of human facial reconstructions. The purpose of this study was to determine mouth width 3-dimensionally based on statistical regression model.

MATERIAL AND METHODS

Cone-beam computed tomography scan data from 130 individuals were used to measure the horizontal and vertical dimensions of orbital and nasal structures and intercanine width. The correlation between these hard tissue variables and the mouth width was evaluated using the statistical regression model.

RESULTS

Orbital width, nasal width, and intercanine width were found to be strong predictors of the mouth width determination and were used to generate the regression formulae to find the most approximate position of the mouth.

CONCLUSION

These specific variables may contribute to improving the accuracy of mouth width determination for oral and maxillofacial reconstructions.

Image fusion-based low-dose CBCT enhancement method for visualizing miniscrew insertion in the infrazygomatic crest

Digital dental technology covers oral cone-beam computed tomography (CBCT) image processing and low-dose CBCT dental applications. A low-dose CBCT image enhancement method based on image fusion is proposed to address the need for subzygomatic small screw insertion. Specifically, firstly, a sharpening correction module is proposed, where the CBCT image is sharpened to compensate for the loss of details in the underexposed/over-exposed region. Secondly, a visibility restoration module based on type II fuzzy sets is designed, and a contrast enhancement module using curve transformation is designed. In addition to this, we propose a perceptual fusion module that fuses visibility and contrast of oral CBCT images. As a result, the problems of overexposure/underexposure, low visibility, and low contrast that occur in oral CBCT images can be effectively addressed with consistent interpretability. The proposed algorithm was analyzed in comparison experiments with a variety of algorithms, as well as ablation experiments. After analysis, compared with advanced enhancement algorithms, this algorithm achieved excellent results in low-dose CBCT enhancement and effective observation of subzygomatic small screw implantation. Compared with the best performing method, the evaluation metric is 0.07-2 higher on both datasets. The project can be found at: https://github.com/sunpeipei2024/low-dose-CBCT .

Impact of dental imaging on pregnant women and recommendations for fetal radiation safety: A systematic review

Purpose

This study was conducted to investigate the safety of dental imaging in pregnant women with respect to fetal health.

Materials and Methods

Searches were conducted of the PubMed, Scopus, and Web of Science databases in May 2023. The inclusion criteria encompassed cross-sectional and longitudinal studies that focused on the analysis of diagnostic dental imaging in pregnant women, as well as studies utilizing phantoms to simulate imaging examinations. The exclusion criteria consisted of reviews, letters to the editor, book chapters, and abstracts from scientific conferences and seminars.

Results

A total of 3,913 articles were identified. Based on a review of the titles and abstracts, 3,892 articles were excluded, leaving 21 articles remaining for full-text review. Of these, 18 were excluded, and 4 additional articles were included as cross-references. Ultimately, 7 articles underwent quantitative-qualitative analysis. Three retrospective studies were focused on pregnant women who underwent dental imaging procedures. The remaining 4 studies utilized female phantoms to simulate imaging examinations and represent the radiation doses absorbed by the uterus or thyroid.

Conclusion

Few dental radiology studies have been conducted to determine the safe radiation threshold for pregnant women. Additionally, the reviewed articles did not provide numbers of dental examinations, by type, corresponding to this dose. Dental imaging examinations of pregnant women should not be restricted if clinically indicated. Ultimately, practitioners must be able to justify the examination and should adhere to the "as low as diagnostically acceptable, being indication-oriented and patient-specific" (ALADAIP) principle of radioprotection.

Patient shielding during dentomaxillofacial radiography: Recommendations from the American Academy of Oral and Maxillofacial Radiology

BACKGROUND

The American Academy of Oral and Maxillofacial Radiology established an ad hoc committee to draft evidence-based recommendations and clinical guidance for the application of patient contact shielding during dentomaxillofacial imaging.

TYPES OF STUDIES REVIEWED

The committee reviewed monographs and reports from radiation protection organizations and studies that reported radiation dose to gonads, breasts, and thyroid gland from dentomaxillofacial imaging.

RESULTS

Considering the absence of radiation-induced heritable effects in humans and the negligible dose to the gonads and fetus from dentomaxillofacial imaging, the committee recommends discontinuing shielding of the gonads, pelvic structures, and fetuses during all dentomaxillofacial radiographic imaging procedures. On the basis of radiation doses from contemporaneous maxillofacial imaging, the committee considered that the risks from thyroid cancer are negligible and recommends that thyroid shielding not be used during intraoral, panoramic, cephalometric, and cone-beam computed tomographic imaging.

PRACTICAL IMPLICATIONS

This position statement informs and educates the reader on evolving radiation protection practices and provides simple, unequivocal guidance to dental personnel to implement these guidelines. State and local authorities should be contacted to update regulations to reflect these recommendations.

Evaluation of the radiation protection effectiveness of a lead-free homopolymer in cone beam computed tomography

OBJECTIVE

The objective was to compare the radiation protection effectiveness of a lead-free thermoplastic homopolymer (Anti-RAD) to conventional lead shielding in cone beam computed tomography (CBCT) exposures.

STUDY DESIGN

Thermoluminescent dosimeters were placed on a human bone- and soft tissue-equivalent phantom to record equivalent doses in the thyroid gland, thyroid skin, and breast areas. CBCT images were obtained with the following 3 protocols: (1) without radiation shielding; (2) with 0.5-mm lead equivalent lead-containing shielding; and (3) with 0.5-mm lead equivalent Anti-RAD shielding. Independent t tests were used to evaluate the results.

RESULTS

Compared with exposures without shielding, both lead and Anti-RAD protective devices reduced thyroid gland equivalent doses by approximately 40%, thyroid skin doses by approximately 75%, right breast skin doses by approximately 80%, and left breast skin doses by 75%. The differences in equivalent dose for both types of shielding compared with exposure with no shielding were statistically significant (P ≤ .042). However, there were no significant differences in dose reduction at any site between lead and Anti-RAD shielding (P ≥ .135).

CONCLUSIONS

Radiation protection equivalent to lead can be provided with the Anti-RAD shield. With the use of this material, disadvantages such as damage to the aprons, lead toxicity, weight of lead aprons, and microbial contamination can be reduced.

Insight in to the Awareness of CBCT as an Imaging Modality in the Diagnosis and Management of ENT Disorders: A Cross Sectional Study

The advent of Cone-beam computed tomography (CBCT), has revolutionized 3D imaging in dentistry. CBCT has enormous potential to be used as an alternative imaging modality by Otolaryngologists. But their knowledge regarding CBCT is limited. The study aims to evaluate the awareness of CBCT as an imaging modality among Ear, nose and Throat (ENT) practitioners. The validated questionnaire was sent by email and the participants were asked to fill the google form through the link provided to record the responses. The participants were asked to answer 25 multiple choice questions regarding the general information and practice related to CBCT imaging. Data was evaluated according to the descriptive statistics and the Chi-square test was used to determine the test of significance. The response rate for this study was 84.4%. The mean age of the participants was 44.9 ± 11.3. 69% of the respondents were academicians,14.2% had exclusive clinical practice, and 16.8% had both clinical and academic exposure. Among the study population, 76.8% had never advised CBCT in their practice. Only 10.3% of the study participants were aware of the potential of CBCT in ENT disorders. The mean knowledge, attitude and practice scores were very low regarding the applications of CBCT. Most of the study participants advised CBCT for maxillofacial fractures (78.1%) and was statistically significant p < 0.05. The knowledge about various advantages and clinical applications of CBCT among Otolaryngologists is limited. However, continuing medical education and inclusion in the medical curriculum will increase the scope and awareness about CBCT among ENT fraternity.

The Importance of Correlation between CBCT Analysis of Bone Density and Primary Stability When Choosing the Design of Dental Implants—Ex Vivo Study

This study aims to determine the correlation between the mean value of bone density measured on the CBCT device and the primary stability of dental implants determined by resonant frequency analysis. An experimental study was conducted on a material of animal origin: bovine femur and pig ribs. Two types of implants were used in this study: self-tapping and non-self-tapping of the same dimensions. Results of the experimental study showed a statistically significant correlation between bone density expressed in HU units and the primary stability of self-tapping and non-self- tapping dental implants expressed in ISQ units in bovine femur bones and self-tapping implants and pig rib bones. There was no statistically significant correlation between non-self-tapping dental implants in pig rib bones. Self-tapping and non-self-tapping implants did not show statistical significance in the primary stability in bones of different qualities. The analysis of bone density from CBCT images in the software of the apparatus expressed in HU units can be used to predict the degree of primary stability of self-tapping and non-self-tapping dental implants in bones of densities D1 and D2, and self-tapping dental implants in bones of the lower quality D4.

The C-shaped Canal System in Mandibular Molars of a Saudi Arabian Population: Prevalence and Root Canal Configurations Using Cone-Beam Computed Tomography

OBJECTIVES

This retrospective study aimed to assess the prevalence of the C-shaped canal system in mandibular first and second molars in a Saudi Arabian population using cone-beam computed tomography (CBCT).

MATERIALS AND METHODS

The sample included 300 CBCT images from adults aged 18 to 80 years (38.7 ± 17.9) (150 females and 150 males). All images were analyzed to detect the C-shaped root canal according to Fan's criteria. We also categorized our findings according to the gender and direction of the longitudinal groove. Data were reported as frequencies and percentages. The Chi-squared test was used to analyze proportional differences, with the significance level set at ≤0.05.

RESULTS

The C-shaped canals were observed in 146 mandibular first molars (24.33%) and 182 second molars (30.33%). Male patients had a significantly higher prevalence of C-shaped canals in mandibular second molars than females (P=0.003). The longitudinal groove was most typically detected on the root's lingual surface (53.35%).

CONCLUSION

The incidence of the C-shaped canal in a Saudi Arabian population was 27.33% in the mandibular molars. The longitudinal groove was mostly on the lingual surface. Males showed a higher prevalence of the C-shaped canal than females.

Impact of thyroid gland shielding on radiation doses in dental cone beam computed tomography with small and medium fields of view

OBJECTIVE

The purpose of this study was to evaluate the impact of thyroid gland shielding on radiation doses in dental cone beam computed tomography (CBCT) with small and medium fields of view (FOVs).

STUDY DESIGN

Six CBCT protocols were investigated by exposing an adult anthropomorphic male phantom head without and with thyroid shielding, using 4 small (4 × 5 cm) and 2 medium (10 × 6 cm) FOVs. Twenty metal oxide semiconductor field-effect transistor dosimeters were placed in the phantom head to measure absorbed doses and calculate equivalent doses at 11 sites. Effective doses were calculated based on the tissue weighting factors in International Commission on Radiological Protection Publication 103. The data were analyzed using the independent samples t test.

RESULTS

Thyroid gland shielding led to significant equivalent dose reductions in many tissues for all protocols. Equivalent dose reductions to the thyroid were significant in all 6 protocols (P ≤ .037). Significant reduction depended on the FOV and ranged between 24.5% and 42.6% for the thyroid gland and 4.9% and 34.5% for other tissues and organs. Effective doses were significantly lower in all protocols (P ≤ .016).

CONCLUSIONS

Thyroid gland shielding protects the thyroid gland and other organs and should be utilized with all CBCT examinations where feasible.

Cone-Beam Computed Tomography in Periodontal Diagnosis and Treatment Planning

Diagnosis of periodontal disease depends on conventional clinical parameters. In periodontitis with extensive bone defects, radiographs play a crucial role in arriving at a proper diagnosis. The emergence of cone-beam computed tomography (CBCT) became a boon in oral radiology. Limitations of conventional two-dimensional (2D) radiographs include inadequate visualization of bone defects, lamina dura, and furcation involvement. CBCT generates 3D images of anatomical structures necessary for the periodontal diagnosis of furcation involvement, intrabony defects, and implant placement. CBCT, thus, imparts various potential applications in the field of periodontics which serves to arrive at better diagnostic conclusions.

Root canal morphologies of mandibular premolars in Southeast Anatolian population: Evaluation of CBCT

Background/Aim: This study aimed to evaluate the root canal morphology of mandibular first and second premolars with the aid of cone-beam computed tomography (CBCT) in the Southeast Anatolian population. Material and Methods: The study examined a total of 1258 mandibular first and second premolars using cone-beam computed tomography images of 370 randomly selected patients who applied to the Department of OralDental and Maxillofacial Radiology of Faculty of Dentistry, Dicle University due to various indications. The total number of roots and root canals, canal symmetry and correlations between the right and left side of the mandible, and the prevalence in men and women were recorded. Data was analzyed using the Chi-Square and Fisher's Exact tests. Canal configurations were evaluated based on the Vertucci classification. Results: The evaluation of CT images of a total of 370 individuals showed that 88.89% of the first premolars and 98.45% of the second premolars were symmetrical. The canal anatomy of the first premolars suggested that 85.98% of the premolars were of Type I, 12.02% were of Type V, and 2% were of Type III based on the Vertucci classification. On the other hand, the canal anatomy of the second premolars revealed that 98.83% were of Type I, 0.67% were of Type V, and 0.5% were of Type III. Conclusions: The prevalent morphology of the multiple canals was Type V, except for the Vertucci classification Type I in the mandibular first premolars. Limited number of canal variations were observed in the mandibular second premolars.

In vitro comparison of high-definition US, CBCT and periapical radiography in the diagnosis of proximal and recurrent caries

OBJECTIVE

To assess the in vitro performance of high-definition (HD) US, CBCT and periapical radiography for the visibility of proximal and recurrent caries in teeth with and without restoration.

METHODS

A total of 240 molar teeth were divided into eight groups each comprised of 30 teeth. Control groups consisted of teeth without caries (Group 1-4; N = 120), whereas diseased groups consisted of teeth with proximal caries (Group 5-8; N = 120 teeth). Finally, a total of four image sets were obtained as follows: i) PSP periapical radiography, ii) CBCT 0.075 mm voxel size, iii) CBCT 0.2 mm voxel size and iv) HD US images. The image sets were viewed separately by four observers by using a 5-point confidence scale. Intraclass correlation coefficients were calculated. The areas under the ROC curves were compared using chi-square tests. Significance level was set at α = 0.05.

RESULTS

Intraobserver agreement for both readings for the four observers ranged between 0.848 and 0.988 for CBCT (0.075 mm) images; 0.658 and 0.952 for CBCT (0.2 mm) images; 0.555 and 0.810 for periapical images; 0.427 and 0.676 for US images. Highest AUC values were found for CBCT (0.075 mm) images and lowest for US images. Statistically significant differences were found among CBCT (0.075 mm) images and US images (p < 0.001), CBCT (0.2 mm) images and US images (p < 0.001) and periapical images and US images (p < 0.001) for the detection of proximal caries.

CONCLUSION

Periapical and CBCT images outperformed HD US imaging in the detection of proximal dental caries.

Flat-panel conebeam CT in the clinic: history and current state

Research into conebeam CT concepts began as soon as the first clinical single-slice CT scanner was conceived. Early implementations of conebeam CT in the 1980s focused on high-contrast applications where concurrent high resolution ( < 200    μ m ), for visualization of small contrast-filled vessels, bones, or teeth, was an imaging requirement that could not be met by the contemporaneous CT scanners. However, the use of nonlinear imagers, e.g., x-ray image intensifiers, limited the clinical utility of the earliest diagnostic conebeam CT systems. The development of consumer-electronics large-area displays provided a technical foundation that was leveraged in the 1990s to first produce large-area digital x-ray detectors for use in radiography and then compact flat panels suitable for high-resolution and high-frame-rate conebeam CT. In this review, we show the concurrent evolution of digital flat panel (DFP) technology and clinical conebeam CT. We give a brief summary of conebeam CT reconstruction, followed by a brief review of the correction approaches for DFP-specific artifacts. The historical development and current status of flat-panel conebeam CT in four clinical areas-breast, fixed C-arm, image-guided radiation therapy, and extremity/head-is presented. Advances in DFP technology over the past two decades have led to improved visualization of high-contrast, high-resolution clinical tasks, and image quality now approaches the soft-tissue contrast resolution that is the standard in clinical CT. Future technical developments in DFPs will enable an even broader range of clinical applications; research in the arena of flat-panel CT shows no signs of slowing down.

Dose reduction potential in cone-beam CT imaging of upper extremity joints with a twin robotic x-ray system

Cone-beam computed tomography is a powerful tool for 3D imaging of the appendicular skeleton, facilitating detailed visualization of bone microarchitecture. This study evaluated various combinations of acquisition and reconstruction parameters for the cone-beam CT mode of a twin robotic x-ray system in cadaveric wrist and elbow scans, aiming to define the best possible trade-off between image quality and radiation dose. Images were acquired with different combinations of tube voltage and tube current-time product, resulting in five scan protocols with varying volume CT dose indices: full-dose (FD; 17.4 mGy), low-dose (LD; 4.5 mGy), ultra-low-dose (ULD; 1.15 mGy), modulated low-dose (mLD; 0.6 mGy) and modulated ultra-low-dose (mULD; 0.29 mGy). Each set of projection data was reconstructed with three convolution kernels (very sharp [Ur77], sharp [Br69], intermediate [Br62]). Five radiologists subjectively assessed the image quality of cortical bone, cancellous bone and soft tissue using seven-point scales. Irrespective of the reconstruction kernel, overall image quality of every FD, LD and ULD scan was deemed suitable for diagnostic use in contrast to mLD (very sharp/sharp/intermediate: 60/55/70%) and mULD (0/3/5%). Superior depiction of cortical and cancellous bone was achieved in FD_Ur77 and LD_Ur77 examinations (p < 0.001) with LD_Ur77 scans also providing favorable bone visualization compared to FD_Br69 and FD_Br62 (p < 0.001). Fleiss' kappa was 0.618 (0.594-0.641; p < 0.001), indicating substantial interrater reliability. In this study, we demonstrate that considerable dose reduction can be realized while maintaining diagnostic image quality in upper extremity joint scans with the cone-beam CT mode of a twin robotic x-ray system. Application of sharper convolution kernels for image reconstruction facilitates superior display of bone microarchitecture.

Correlation of Panoramic Radiography, Cone-Beam Computed Tomography, and Three-Dimensional Printing in the Assessment of the Spatial Location of Impacted Mandibular Third Molars

The development of radiology, rapid prototyping techniques, and the increasingly common use of 3D printing in dentistry inspires the use of these techniques to improve diagnostic and therapeutic processes. This study aimed to conduct a retrospective comparative analysis of dental panoramic radiographs, cone-beam computed tomography, and 3D printing in preoperative assessment of the procedure's difficulty. Thirty clinical cases with a high degree of difficulty were selected, and based on evaluation with CBCT, a virtual 3D model of the region of surgical procedure was created, which was then printed using a 3D printer. The comparative analysis included the linear measurements performed in dental panoramic radiographs, cone-beam computed tomography, and 3D models in a preoperative assessment of the degree of retention and difficulty of impacted mandibular third molars in the mandible. Linear measurements performed on dental panoramic radiographs were significantly lower than in cone-beam computed tomography and 3D models. No statistically significant differences were obtained in linear measurements between 3D models and cone-beam computed tomography images except for the measurement of the lingual lamina thickness; however, due to the insignificant differences in measurements, with a mean of only 80 µm, the elective procedure of removal of the impacted third molar in the mandible may be safe.

Assessment of Anterior Loop of Inferior Alveolar Nerve and Its Anatomic Variations with Age, Gender, and Dentition Status in Indian Population: A CBCT Study

Background

The posterior region of the mandible is more often related to iatrogenic errors, but the interforaminal region is also not spared for neurovascular complications. This study aimed to use CBCT images to evaluate the prevalence of anterior nerve looping and its variations with age, gender, and dentition status.

Methods

This retrospective study was carried out by studying 600 CBCT scans retrieved from archival records of a CBCT center in Lucknow. The scans were inspected by two trained investigators. The length of the anterior loop was measured using the measuring tool of Carestream 3D imaging software. Descriptive and analytical tests were performed.

Results

The prevalence of the anterior loop of the inferior alveolar nerve was found to be 56%. The prevalence was found to be more on the right side (29.0%) compared to the left side (27.0%). The most common anterior looping of the inferior alveolar nerve was type 3 followed by type 1. Males were found to have significantly higher loops compared to females. The number of loops was found to decrease significantly with age. The mean length of the loop was found to vary from 1.14 to 1.61 mm.

Conclusion

The anterior looping of IAN is very much prevalent in the Lucknow population. The use of the CBCT technique and appropriate preplanning prior to surgery or implant placement should be performed to prevent nerve injury.

A Comparative Study of Multidetector Computed Tomography, Cone Beam Computed Tomography, and Computed Microtomography on Trabecular Bone Structures in the Human Mandible: An Ex Vivo Study

OBJECTIVE

The aim of this study was to evaluate the accuracy of multislice computed tomography (MSCT) and cone beam computed tomography (CBCT) scanners in the assessment of trabecular bone microarchitecture by radiomorphometric analysis.

METHODS

Eight dry human hemimandibles were selected and scanned by 4- and 128-MSCT, CBCT with different voxel sizes, and a computed microtomography (micro-CT). The images were spatially aligned, the axial slices were segmented using CTAn software (Skyscan, Konitch, Belgium), and 10 bone morphometric parameters were quantified. The micro-CT images were the criterion standard.

RESULTS

The results show the superiority of CBCT images with 0.2-mm voxel size and 128-MSCT.

CONCLUSIONS

We can conclude that the CBCT scanner with 0.2-mm voxel size and 128-MSCT had better performance on reproducibility of the distribution and organization of trabecular bone and marrow spaces evaluated in this study.

A Novel Digital Implant Planning Workflow in Patients with Preexisting Metal Restorations: A Technical Report

A prosthetically-driven virtual implant plan is considered a challenging procedure depending on accurate registration of the three-dimensional optical surface scan and 3D volumetric rendering reconstructed from cone-beam computed tomography (CBCT) images. However, the presence of preexisting metal restorations may significantly negatively influence the registration process. This technical report describes a novel digital workflow to optimize the implant planning outcome for the partially edentulous patient with preexisting metal restorations by accurately aligning the standard triangle language data of the intraoral scanner with the CBCT rendering using a dual-scan technique and an appliance with radiographic markers.

A Questionnaire of Digital Radiography and CBCT Use and Knowledge among Lithuanian Dentists

Objectives

Digital radiography is an increasingly used technology in Lithuania. However, there is no published information about using cone-beam computed tomography. The aims of this cross-sectional study performed in Lithuania were (1) to obtain information about the prevalence and accessibility of digital radiography and cone-beam computed tomography usage, and (2) to estimate dental practitioners’ knowledge about this diagnostic method and their need for education.

Material and Methods

Questionnaires consisting of 31 questions were distributed during the 2019 International Dentist Congress in Lithuania.

Results

This study analyses the data obtained from 248 respondents. Most of the clinicians use digital radiographic methods in their practice. The institutions usually have a digital dental X-ray machine, less often a digital panoramic X-ray machine, and least often a cone-beam computed tomography (CBCT) unit. Most dental practitioners performed 1 to 10 CBCT scans per month for adult patients and the most frequent reason for its use was implantation planning. Of the practitioners, 81.7% would like to improve their CBCT knowledge and skills.

Conclusions

The number of digital X-ray machines has increased throughout the last decade. Lithuanian dental practitioners do not excessively use cone-beam computed tomography. Some concerns were raised regarding respondents’ knowledge about exposure factors and this diagnostic method’s performance for paediatric patients. Additional training should be provided to Lithuanian dental specialists.

Sagittal Relationship between the Maxillary Central Incisors and the Forehead in Digital Twins of Korean Adult Females

OBJECTIVE

Digital twins of adult Korean females were created as a tool to evaluate and compare the sagittal relationship between the maxillary central incisors and the forehead before and after orthodontic treatment.

METHODS

Digital twins were reconstructed for a total of 50 adult female patients using facial scans and cone-beam computed tomography (CBCT) images. The anteroposterior position of the maxillary central incisor and the forehead inclination were measured.

RESULTS

The control group presented a mean of 6.7 mm for the sagittal position and 17.5° for forehead inclination. The study group showed a mean of 9.3 mm for the sagittal position and 13.6° for forehead inclination. Most Korean females seeking orthodontic treatment had their maxillary central incisor anterior to the glabella. In contrast, fewer Korean females who completed their orthodontic treatments had their maxillary central incisor anterior to the glabella. Furthermore, patients who had completed the orthodontic treatment were more likely to have the maxillary central incisor between the forehead facial axis and glabella.

CONCLUSION

The use of digital twins for three-dimensional (3D) analysis of the profile implies a high clinical significance. In addition, as the facial profile of Koreans is different from that of Caucasians, careful consideration should be made when setting treatment goals for the anteroposterior position of the maxillary central incisors.

Radicular Grooves and Complex Root Morphologies of Mandibular Premolars Among Israeli Population

INTRODUCTION

Mandibular premolars usually have one root and one root canal. Different studies found that up to 30% of mandibular premolars have more than one root canal, and up to 24% of mandibular premolars have C-shape canals. The purpose of this study was to investigate the root anatomy and the prevalence of complex root canal morphology in mandibular premolars in Israeli population.

METHODS

A total of 1020 Israeli patients' cone-beam computed tomography scans were screened and evaluated. A total of 1835 mandibular first premolars and 1678 mandibular second premolars were examined. Irregular root anatomy and different root canal morphologies were recorded and analyzed.

RESULTS

The overall prevalence of complex root morphology (types II-VIII) in mandibular first and second premolars was 21% and 2.8%, respectively. The bilateral prevalence of complex root morphology in mandibular first and second premolars was 46% and 29%, respectively. The prevalence of radicular grooves in mandibular first and second premolars with complex root morphology was 48% and 36%, respectively. No significant difference was found according to gender or the side of occurrence. However, complex root canal morphology was significantly found in mandibular premolars with radicular grooves.

CONCLUSIONS

Complex root canal morphology frequently occurs in mandibular first premolars in the population of Israel. Radicular groove existence in mandibular first and second premolars is significantly related to complex root canal morphology.

Three dimensional (3D) imaging techniques in orthodontics-An update

3D imaging is a technique which develops or creates the impression of depth within an image by deploying 2D data into 3-dimensional format. To aid in quality regulating processes for industrial purposes, 3D imaging has become an extremely valuable factor. Owing to their various drawbacks, a wide range of investigative methods formulated for demonstration of facial structures and the dentition were dilapidated. Currently in medicine, the most prevalent method is perhaps 3D imaging technique renders thorough and problem specific information regarding hard and the soft tissues, such as Computerized Tomography (CT), Cone Beam Computerized Tomography (CBCT), Micro Computerized Tomography (MCT), 3D laser scanning, structured light technique, stereophotogrammetry or 3D surface imaging systems (3dMD), 3D facial morphometry (3DFM), Tuned Aperture Computed Tomography (TACT), and Magnetic Resonance Imaging (MRI). 3D imaging techniques in orthodontics plays an important role by facilitating more elaborated diagnostic information on the precise cases like patients having craniofacial anomalies. Hence, the aim of this study was to review advances in 3D imaging with in the field of orthodontics.

Cone-beam computed tomography and its applications in dental and maxillofacial radiology

Cone-beam computed tomography (CBCT) was first used in dental and maxillofacial radiology (DMFR) at the end of the 1990s. Since then, it has been successfully established as the standard three-dimensional radiographic imaging technique in DMFR, with a wide variety of applications in this field. This manuscript briefly reviews the background information on the technology and summarises available data on effective dose and dose optimisation. In addition, typical clinical applications and indications of the technique in DMFR are presented.

Screening of Pediatric Facial Fractures by Brain Computed Tomography: Diagnostic Performance Comparison With Facial Computed Tomography

OBJECTIVES

Facial bone fractures secondary to head trauma are more common in children than in adults. Recently, multidetector row computed tomography (CT) has been considered superior to conventional radiography. Some studies have reported that facial soft tissue injuries require both facial and brain CT and that brain CT is helpful in screening facial bone fractures. However, these studies included only adult patients. The aim of this study was to evaluate the diagnostic performance of brain CT and the need for additional facial CT to detect facial bone fractures in emergency pediatrics.

METHODS

This multicenter study was conducted retrospectively in 2 tertiary hospitals in Seoul, Republic of Korea. The data were collected from the medical records of pediatric patients younger than 8 years who had undergone both brain and facial CT on the same day in the emergency department. All CT scans were retrospectively and independently evaluated by 1 board-certified radiologist and 1 board-certified emergency medicine physician. A P value of <0.05 was considered statistically significant.

RESULTS

Sensitivity was 92.31%, specificity was 100%, positive predictive value was 100%, negative predictive value was 99.31%, and accuracy was 99.36% for the emergency physician; all parameters were 100% for the radiologist.

CONCLUSIONS

Brain CT showed high diagnostic performance to detect facial bone fractures with high accuracy in pediatric patients. As emergency physicians, we should consider facial bone fractures when reviewing brain CT images of pediatric patients with blunt head and face trauma.

Upper airway visualization in pediatric obstructive sleep apnea

Pediatric Obstructive Sleep Apnea (OSA) is a condition that may lead to a variety of comorbidities in adolescence and adulthood. The gold standard of diagnosing OSA is polysomnography (PSG). Over the past fifteen years numerous publications have explored how to better visualize the upper airway to further assess OSA in the pediatric population, and eventually institute personalized treatment. Lateral neck radiograph, cephalometry, computed axial tomography, and magnetic resonance imaging are all unique imaging techniques that are used in the diagnosis of OSA. Drug Induced Sleep Endoscopy is a direct visualization technique that is gathering momentum in pediatrics. Each approach has respective benefits and weaknesses. However, none of them at this time can replace PSG. They are a helpful supplement in those patients with complicated upper airway anatomy and in those with residual OSA.

Cone-Beam Computed Tomography in Orthodontics

Unlike patients receiving implants or endodontic treatment, most orthodontic patients are children who are particularly sensitive to ionizing radiation. Cone-beam computed tomography (CBCT) carries risks and benefits in orthodontics. The principal risks and limitations include ionizing radiation, the presence of artifacts, higher cost, limited accessibility, and the need for additional training. However, this imaging modality has several recognized indications in orthodontics, such as the assessment of impacted and ectopic teeth, assessment of pharyngeal airway, assessment of mini-implant sites, evaluation of craniofacial abnormalities, evaluation of sinus anatomy or pathology, evaluation of root resorption, evaluation of the cortical bone plate, and orthognathic surgery planning and evaluation. CBCT is particularly justified when it brings a benefit to the patient or changes the outcome of the treatment when compared with conventional imaging techniques. Therefore, CBCT should be considered for clinical orthodontics for selected patients. Prescription of CBCT requires judicious and sound clinical judgment. The central question of this narrative review article is: when does CBCT add value to the practice of orthodontics? To answer this question, this article presents discussion on radiation dosage of CBCT and other imaging techniques used in orthodontics, limitations of CBCT in orthodontics, justifying the use of CBCT in orthodontics, and the benefits and evidence-based indications of CBCT in orthodontics. This review summarizes the central themes and topics in the literature regarding CBCT in orthodontics and presents ten orthodontic cases in which CBCT proved to be valuable.

Thyroid shielding in cone beam computed tomography: recommendations towards appropriate use

The objective of this paper is to provide recommendations towards the appropriate use of thyroid shielding in dental cone beam CT (CBCT). Based on current evidence of thyroid radiosensitivity, dosimetric data in the presence and absence of shielding, and a depiction of potential adverse effects of thyroid shielding, a concise set of recommendations was prepared. According to current risk models, thyroid sensitivity is particularly high at a young age, and much higher for females. In the literature, involving adult male, female and paediatric reference phantoms, the use of a tightly fitted thyroid collar with a lead-equivalent thickness of at least 0.25 mm has consistently shown a significant reduction (average: 45.9%) of the equivalent dose to the thyroid. It can therefore be recommended that thyroid shielding should be routinely used for children undergoing CBCT scanning and is recommended for adults up to the age of 50. The increase of the X-ray tube current from automatic exposure control systems due to thyroid shielding can be avoided by placing the shielding collar after acquiring the scout images. Should real-time tube current modulation be implemented in dental CBCT imaging in the future, perspectives regarding the appropriate use of shielding may change according to current trends in CT. In view of the manifestation of metal artefacts, shielding is best avoided if radiological evaluation of tissues below the lower border of the mandible is needed.

Cone Beam Computed Tomography-Based Anatomical Assessment of the Olfactory Fossa

This study aimed to investigate the olfactory fossa according to the Keros classification using cone beam computed tomography. This cross-sectional study analysed cone beam computed tomography images selected from a database belonging to a radiology centre. The scans of 174 healthy patients were analysed by using the Xoran software. Gender, age, and side were correlated with the Keros classification. The mean age of the 174 patients was 45.3 years. The most prevalent Keros classification was type II (65.52%), followed by type III (20.69%) and type I (13.79%). No significant differences were found between Keros classification and the variables age, right side (p value = 0.4620), and left side (p value = 0.5709). There were also no significant differences between gender and the variables right side (p value = 0.1421) and left side (p value = 0.2136). Based on these results, we suggest that cone beam computed tomography can be recommended for analysis of the anterior skull base. Keros type II was the most prevalent type in our sample.

New and emerging patient-centered CT imaging and image-guided treatment paradigms for maxillofacial trauma

This article reviews the conceptual framework, available evidence, and practical considerations pertaining to nascent and emerging advances in patient-centered CT-imaging and CT-guided surgery for maxillofacial trauma. These include cinematic rendering-a novel method for advanced 3D visualization, incorporation of quantitative CT imaging into the assessment of orbital fractures, low-dose CT imaging protocols made possible with contemporary scanners and reconstruction techniques, the rapidly growing use of cone-beam CT, virtual fracture reduction with design software for surgical pre-planning, the use of 3D printing for fabricating models and implants, and new avenues in CT-guided computer-aided surgery.

Evaluation of mandibular odontogenic keratocyst and ameloblastoma by panoramic radiograph and computed tomography

OBJECTIVES:

The purpose of this study was to describe and compare the main imagenological features of mandibular ameloblastomas and odontogenic keratocyst (OKC) using panoramic radiograph (PR) and CT.

METHODS:

The sample consisted of nine cases of ameloblastomas and nine cases of OKC. PR and CT images were analyzed according to shape, internal structure, borders, associated unerupted tooth, root resorption, expansion and perforation of cortical bones.

RESULTS:

PR evaluation allowed the identification of the lesion's location, presence of sclerosis in the periphery, presence of associated non-erupted tooth and expansion of the mandible's lower border cortical bone. CT was more accurate than PR in the assessment of the lesion shape, presence of inner bone septa, root resorption, buccolingual expansion and rupture of cortical bone. Most cases of ameloblastoma and OKC presented buccolingual expansion and erosion of cortical bone. Only ameloblastomas showed tooth root resorption.

CONCLUSIONS:

Although PR is very helpful and widely used, CT provides more precise information on buccolingual expansion, calcification, bone septa, perforation of cortical bones and tooth resorption, features that are frequently underdescribed in the literature, particularly in OKC.

The Effect of Original and Invert Enhanced Panoramic Modality on the Assessment of the Relationship Between the Maxillary Posterior Roots and the Maxillary Sinus Floor

Background:

Having knowledge about the anatomical and pathological relationship between the maxillary posterior root tip and the maxillary sinus floor is very significant for preoperative treatment planning.

Aims and Objectives:

The purpose of the present study was to compare the accuracy of original panoramic radiographs and digital panoramic images over cone beam computed tomography (CBCT) images in evaluating the relationship between the maxillary posterior teeth and the maxillary sinus floor, and to verify the accuracy of the signs of the relationship between the roots of the maxillary posterior teeth and maxillary sinus on the panoramic radiographs over CBCT images.

Materials and Methods:

From 106 subjects (47 males and 59 females; mean age = 39 years; range = 18-67 years) referred to our university, a pair of panoramic and CBCT images was selected for further analysis. The relationship between the maxillary posterior teeth, the maxillary sinus, and panoramic radiography signs (root projection into the sinus, interruption of the maxillary sinus floor cortex, absence of lamina dura, darkening of the root apex, and curvature of the sinus floor on the root apex) associated with the protrusion of root apexes into the sinus was evaluated.

Results:

The P values of the data obtained from the original and invert enhanced panoramic images were .53 and .52, respectively, and there was no statistically significant difference in the accuracy of the 2 methods ( P > .05).

Conclusion:

The root projection into the sinus is an indicative sign of root protrusion into the sinus on CBCT.

Prevalence of C-shaped canal system in mandibular first and second molars in a Saudi population assessed via cone beam computed tomography: a retrospective study

OBJECTIVES

The purpose of this study was to determine the prevalence of the C-shaped root canal configuration, location of the longitudinal groove, sex differences, and unilateral/bilateral presence in mandibular first and second molars in a Saudi population using cone beam computed tomography (CBCT).

MATERIALS AND METHODS

CBCT images for the mandibular first and second molars of 487 patients (a total of 529 first molars and 681 s molars) were evaluated. The teeth were assessed for the presence of C-shaped root canals according to Fan criteria. Subdivisions were also made according to sex, direction of the longitudinal groove, and unilateral/bilateral presence.

RESULTS

Only one C-shaped mandibular first molar was observed (0.19%), whereas 62 second molars (9.1%) exhibited C-shaped anatomy. Unilateral presence of the C-shaped root canal system was more common (53.85%). Female patients had a higher prevalence than males. Longitudinal grooves were most commonly found on the root lingual surface (58.1%).

CONCLUSIONS

The prevalence of the C-shaped canal configuration in a Saudi Arabian population was 0.19% in the mandibular first molar and 9.1% in the mandibular second molar. Longitudinal groove prevalence was highest on the lingual surface. Women had a significantly higher prevalence of the C-shaped canal configuration than men. Patients with unilateral presence of the C-shaped canal configuration were more common than those with bilateral presence.

CLINICAL RELEVANCE

Tooth type, patient sex, and ethnicity can help clinicians predict the prevalence of the C-shaped canal system in mandibular molars.

Evaluation of Root Canal Morphology of Mandibular First and Second Premolars Using Cone Beam Computed Tomography in a Defined Group of Dental Patients in Iran

BACKGROUND

Successful dental root canal treatments require a complete knowledge of dental anatomy and root canal morphology.

MATERIALS AND METHODS

One hundred and forty-five cone beam computed tomography (CBCT) images were used to assess the anatomy and morphology of mandibular premolars based on Vertucci's classifications in a defined group of dental patients in Iran. The number of roots and root canals, root canal morphology, root and canal shape (curvature), existence of C-shaped canal, and influence of sex on each of these were evaluated. A chi-squared test was used for statistical analysis.

RESULTS

The mandibular first and second premolars had a single root in 95.97% and 100% cases, respectively. In the mandibular first premolars, 62.2% were of type I, 0.8% type II, 10.9% type III, 0.8% type IV, 20.3% type V, 4.2% type VI, and 0.8% type VII; in the second premolars, 78% of canals were of type I, 3% type II, 11% type III, 7% type V, and 1% type VI. C-shaped canals did not exist in either of the premolars. The most prevalent root and canal shape was straight. The most prevalent root curvature was a distal curvature in both premolars (71.4% and 74% of first and second premolars, resp.). The most prevalent canal curvature was lingual and buccal for the first premolars (7.6% each) and distal for the second premolars (11%). No significant difference was found between men and women in nearly all of the above (P > 0.05).

CONCLUSION

The results suggest that there is a need to conduct further evaluations on finding root and canal variations among more populations to gain better knowledge prior to root canal treatment.

Three-Dimensional Cone Beam Computed Tomography Volumetric Outcomes of rhBMP-2/Demineralized Bone Matrix versus Iliac Crest Bone Graft for Alveolar Cleft Reconstruction

BACKGROUND

Recent studies indicate that recombinant human bone morphogenetic protein-2 (rhBMP-2) in a demineralized bone matrix scaffold is a comparable alternative to iliac bone autograft in the setting of secondary alveolar cleft repair. Postreconstruction occlusal radiographs demonstrate improved bone stock when rhBMP-2/demineralized bone matrix (DBM) scaffold is used but lack the capacity to evaluate bone growth in three dimensions. This study uses cone beam computed tomography to provide the first clinical evaluation of volumetric and density comparisons between these two treatment modalities.

METHODS

A prospective study was conducted with 31 patients and 36 repairs of the alveolar cleft over a 2-year period. Twenty-one repairs used rhBMP-2/DBM scaffold and 14 repairs used iliac bone grafting. Postoperatively, occlusal radiographs were obtained at 3 months to evaluate bone fill; cone beam computed tomographic images were obtained at 6 to 9 months to compare volumetric and density data.

RESULTS

At 3 months, postoperative occlusal radiographs demonstrated that 67 percent of patients receiving rhBMP-2/DBM scaffold had complete bone fill of the alveolus, versus 56 percent of patients in the autologous group. In contrast, cone beam computed tomographic data showed 31.6 percent (95 percent CI, 24.2 to 38.5 percent) fill in the rhBMP-2 group compared with 32.5 percent (95 percent CI, 22.1 to 42.9 percent) in the autologous population. Density analysis demonstrated identical average values between the groups (1.38 g/cc).

CONCLUSIONS

These data demonstrate comparable bone regrowth and density values following secondary alveolar cleft repair using rhBMP-2/DBM scaffold versus autologous iliac bone graft. Cone beam computed tomography provides a more nuanced understanding of true bone regeneration within the alveolar cleft that may contribute to the information provided by occlusal radiographs alone.

CLINICAL QUESTION/LEVEL OF EVIDENCE

Therapeutic, II.

The use of a thyroid shield for intraoral anterior oblique occlusal views-a risk-based approach

OBJECTIVES

To estimate the radiation dose reduction to the thyroid for an anterior oblique occlusal view from the use of a thyroid shield, compare this with the variation in thyroid dose resulting from differences in examination positioning and discuss the additional considerations associated with the use of a thyroid shield before making a recommendation on their routine use for this examination.

METHODS

Doses to the oral mucosa, the salivary glands, the thyroid, the extrathoracic airways, the oesophagus and the lungs were directly measured for anterior oblique occlusal X-rays of a Rando phantom with and without a thyroid shield using strips of calibrated XRQA Gafchromic film. The examination was also simulated using Monte Carlo software for the without thyroid shield case for a comparison of the dose and to evaluate the dosimetric effect of suboptimal examination positioning.

RESULTS

A 36% reduction in thyroid dose was measured as a result of thyroid shield use; the effective dose reduction is of the order of 22%. Suboptimal positioning was found to increase thyroid dose by a far more significant amount.

CONCLUSIONS

Despite the reduction in thyroid dose, cost-benefit considerations mean that the purchase of a thyroid shield is only recommended where a very high number of anterior oblique occlusal views are undertaken. Optimization efforts for this examination are better focussed on training in examination positioning.

EVALUATION OF THYROID RADIATION DOSE USING CONE BEAM COMPUTED TOMOGRAPHY

Cone beam computed tomography (CBCT) became common in various dental specialties over the past decade. This technology is used by dental professionals regarding the investigation of maxillofacial structures. Due to the diagnostic quality and possibility of 3D view, this method has become an additional method of human exposure to ionizing radiation. This study aims to evaluate the amount of ionizing radiation absorbed by thyroid gland using CBCT. Measurements were performed by LiF dosimeters (TLD-100), positioned on a phantom for head and neck, which was irradiated by Newtom 3G-CBCT. The average of phantom surface radiation dose at the thyroid gland was 0.48 mGy. The data obtained during this study are suitable to reference values; therefore, it is important to recall that the as low as reasonably achievable principle must be applied in all procedures, thereby safeguarding the patient and also the professional.