TiO2 nanotube arrays with a volume expansion factor greater than 2.0: Evidence against the field-assisted ejection theory

Synthesis and Study of SrTiO3/TiO2 Hybrid Perovskite Nanotubes by Electrochemical Anodization

Layers of TiO2 nanotubes formed by the anodization process represent an area of active research in the context of innovative energy conversion and storage systems. Titanium nanotubes (TNTs) have attracted attention because of their unique properties, especially their high surface-to-volume ratio, which makes them a desirable material for various technological applications. The anodization method is widely used to produce TNTs because of its simplicity and relative cheapness; the method enables precise control over the thickness of TiO2 nanotubes. Anodization can also be used to create decorative and colored coatings on titanium nanotubes. In this study, a combined structure including anodic TiO2 nanotubes and SrTiO3 particles was fabricated using chemical synthesis techniques. TiO2 nanotubes were prepared by anodizing them in ethylene glycol containing NH4F and H2O while applying a voltage of 30 volts. An anode nanotube array heat-treated at 450 °C was then placed in an autoclave filled with dilute SrTiO3 solution. Scanning electron microscopy (SEM) analysis showed that the TNTs were characterized by clear and open tube ends, with an average outer diameter of 1.01 μm and an inner diameter of 69 nm, and their length is 133 nm. The results confirm the successful formation of a structure that can be potentially applied in a variety of applications, including hydrogen production by the photocatalytic decomposition of water under sunlight.

A comparative study of two-step anodization with one-step anodization at constant voltage

Two-step anodization has been widely used because it can produce highly self-organized anodic TiO₂nanotubes, but the differences in morphology and current-time curve of one-step anodization and two-step anodization are rarely reported. Here, one-step anodization and two-step anodization were conducted at different voltages. By comparing the FESEM image of anodic TiO₂nanotubes fabricated by one-step anodization and two-step anodization, it was found that the variation of morphology characteristics is same with voltage. The distinction of morphology and current-time curve between one-step anodization and two-step anodization at the same voltage were analyzed: the nanotube average growth rate and porosity of two-step anodization are greater than that of one-step anodization. In the current-time curve, the duration of stage I and stage II in two-step anodization are significantly shorter than one-step anodization. The traditional field-assisted dissolution theory cannot explain the three stages of the current-time curves and their physics meaning under different voltages in the same fluoride electrolyte. Here, the distinction between one-step anodization and two-step anodization was clarified successfully by the theories of ionic current and electronic current and oxygen bubble mould.

A phosphoric anion layer inhibits electronic current generation and nanotube growth during anodization of titanium

Nowadays the formation mechanism of anodic TiO2 nanotubes has attracted extensive attention. Field-assisted dissolution (TiO2 + 6F- + 4H+ → [TiF6]2- + 2H2O) has been considered as the causal link to the formation and growth of nanotubes. But it is hard for this theory to explain three stages of the current-time curve. Here, the anodization of titanium was studied by adding different concentrations of H3PO4 (0%, 4 wt%, 6 wt%, 8 wt%, and 10 wt%) in ethylene glycol containing the same concentration of NH4F (0.5 wt%). The results prove that under the action of the same concentration of NH4F, the growth rate of nanotubes decreases obviously with the increase of H3PO4 concentration, and the second stage of the current-time curve is also prolonged simultaneously. These experimental facts cannot be interpreted by field-assisted dissolution theory and the viscous flow model. Here, an anion layer formed by H3PO4 and the electronic current theory are ably used to explain these facts reasonably for the first time.

Tuning Structural Colors of TiO2 Thin Films Using an Electrochemical Process

TiO₂ films exhibiting structural colors were successfully prepared using one-step electrochemical oxidation. Results of theoretical analyses and digital simulations revealed that the structural color of a TiO₂ thin film could be regulated by adjusting oxidation voltage and oxidation time with different oxidation voltages leading to changes in structural color annulus number. At a low oxidation voltage, each thin film exhibited a single structural color, while thin films with different structural colors were obtained by varying the oxidation time. By contrast, at a higher oxidation voltage, each film exhibited iridescent and circular structural color patterns associated with symmetrical decreases in surface oxidation current density along radial lines emanating from the film center to its outer edges. TiO₂ films exhibiting iridescent structural colorations have broad application prospects in industrial fields related to photocatalysis and photovoltaic cells.

Ordered Nanopillar Arrays of Low Dynamic Noise Dry Bioelectrodes for Electrocardiogram Surface Monitoring

Flexible bioelectric dry electrodes are an important part of long-term medical healthcare monitoring systems. In this study, a new method is proposed for the preparation of dry electrodes with micronanopillar arrays structured by designing dimensionally tunable anodized aluminum oxide (AAO) templates, by which polyaniline/thermoplastic polyurethane single-layer micronanopillar array structured dry electrodes (PANI/TPU-SE) and polyaniline/thermoplastic polyurethane double-layer micronanopillar array structured dry electrodes (PANI/TPU-DE) are prepared. Compared with the planar structure, the micronanopillar array structure can reduce the contact gap between the electrode and skin and increase the contact area, thus exhibiting lower contact impedance and higher signal quality. At 0.1 Hz, the impedances of the wet electrode, PANI/TPU-DE300, PANI/TPU-SE10, and planar structure electrodes are 269.5 kΩ, 375.5 kΩ, 398.1 kΩ, and 2.257 MΩ, respectively, and the impedance value for PANI/TPU-DE300 is smaller than that for PANI/TPU-SE10 and closer to that for the wet electrode. In addition, because the surface of the micronanostructure can conform to the human skin, about 210.7% increase in the peel strength of double-layer structure electrodes compared to flat structure electrodes, it shows a low baseline drift in the dynamic ECG measurement, and the signal-to-noise ratio in the walking state can reach 21.33 ± 5.4775 dB. Therefore, the prepared bioelectric dry electrode has a wide application prospect in the fields of wearable medical monitoring.

Loading Nano-CuO on TiO2 Nanomeshes towards Efficient Photodegradation of Methylene Blue

In order to improve the photocatalytic activity of TiO2, we successfully loaded nano-CuO on the TiO2 nanomeshes as CuO-TiO2 nanocomposites through a facile electrodeposition method. The optimized calcined temperature after Cu electrodeposition is confirmed as 450 °C, which could furthest assist the crystallization of anatase TiO2 and guarantee the high photocatalytic activity of CuO-TiO2 nanocomposites. Comparing with pure TiO2 nanomeshes, CuO-TiO2 nanocomposites showed better degradability of methylene blue, and the degradation efficiency reached to 35% after 120 min irradiation. Additionally, CuO-TiO2 nanocomposites exhibit much stronger absorption intensity within the visible light scope, more than two times than that of pure TiO2 nanomeshes, which indicates that the loading of nano-CuO could promote photocatalytic efficiency by the strong visible light absorption. Additionally, CuO-TiO2 nanocomposites show faster photocurrent response and lower charge transfer resistance than that of pure TiO2 nanomeshes, which implies that the recombination rate of photogenerated electron-hole pairs was reduced after nano-CuO loading.

Facile preparation of MnO2-TiO2 nanotube arrays composite electrode for electrochemical detection of hydrogen peroxide

The MnO₂-TNTA composite electrodes were obtained through depositing MnO₂ into TiO₂ nanotube arrays (TNTA) by successive ionic layer adsorption reaction (SILAR) and subsequent hydrothermal method. The MnO₂-TNTA nanocomposites were used as electrochemical sensors for the detection of hydrogen peroxide (H₂O₂). The preparation conditions of MnO₂-TNTA electrodes and test conditions affect the electrochemical detection performance significantly. The optimal conditions are listed as follows: the number of SILAR cycles, 6 times; KMnO₄ solution temperature, 50 °C; supporting electrolyte, 0.5 M NaOH. Under these conditions, the MnO₂-TNTA electrode exhibits the best performance for detecting H₂O₂. The optimized MnO₂-TNTA electrode has a minimum detection limit of 0.6 μM (S/N = 3) and a linear range of 5 μM ∼ 13 mM, which is much superior to the previously-reported electrodes. Moreover, the optimized MnO₂-TNTA electrode possesses high selectivity, excellent stability and good reproducibility in the detection of H₂O₂. When used in the determination of H₂O₂ content in actual samples including disinfectant and milk, it also shows good accuracy, ideal recovery (96.00% ∼ 102.67%) and high precision (RSD < 4.0%).

A review: research progress on the formation mechanism of porous anodic oxides

Owing to the great development potential of porous anodic oxides (PAO) in many fields, research on their formation mechanisms, fabrication processes and applications has a history of more than ten years. Although compared with research on the fabrication processes and applications of PAO, research on their formation mechanisms started late, several mainstream theories have been formed in the academic community, including the field-assisted dissolution (FAD) theory, the field-assisted ejection (FAE) theory, the self-organization theory, the ionic and electronic current theory and the oxygen bubble mould effect. This review will focus on summarizing the core views of the mainstream mechanisms mentioned above and comparing the explanations for some of their classical experimental phenomena.

Unraveling the six stages of the current-time curve and the bilayer nanotubes obtained by one-step anodization of Zr

The application and growth mechanism of anodic TiO2 nanotubes have been a hot topic in the last ten years, but the formation mechanism of anodic ZrO2 nanotubes has rarely been studied. In one-step constant voltage anodization of Al and Ti, the typical current-time curve has three stages. Moreover, the current-time curves of the three stages can last for 10 min or even 10 hours, resulting in a single layer of nanotubes with the same diameter due to the constant voltage in one-step anodization. However, in this paper, it was found for the first time that the three stages of the current-time curve appeared twice in succession during one-step constant voltage anodization of Zr for only 900 seconds, and bilayer nanotubes with increased diameter were obtained. This six-stage current-time curve cannot be explained by classical field-assisted dissolution and field-assisted flow or stress-driven mechanisms. Here, the formation mechanism and growth kinetics of bilayer ZrO2 nanotubes have been clarified rationally by the theories of ionic current, electronic current and oxygen bubble mold. The interesting results presented in this paper are of great significance for revealing the anodizing process of various metals and the formation mechanism of porous structures.

Sheet-on-sheet TiO2/Bi2MoO6 heterostructure for enhanced photocatalytic amoxicillin degradation

Developing sheet-on-sheet (2D/2D) heterostructure with built-in electric field (BIEF) is effective in boosting the performance of photocatalysts for emerging contaminants degradation. Herein, the 2D/2D microtopography and (-)TiO₂/(+)Bi₂MoO₆ BIEF were precisely integrated into hierarchical nanosheets, which can provide the basis and driving force for charge transfer both in in-plane and interface of heterojunction. The prepared photocatalyst (TiO₂/Bi₂MoO₆) showed high-efficiency and stable performance for photocatalytic amoxicillin (AMX) degradation, which was 18.2 and 5.7 times higher than TiO₂ and Bi₂MoO₆, respectively. More importantly, TiO₂/Bi₂MoO₆ showed more efficient photocatalytic activity and photogenerated charge separation than TiO₂@Bi₂MoO₆ (different morphology). Besides, four possible pathways of AMX degradation were proposed depending on Gaussian calculations and intermediates analysis by GC-MS and HPLC-TOFMS. This work sheds light on the design and construction of unique 2D/2D heterostructure photocatalysts for AMX degradation.

Debunking the essential effect of temperature and voltage on the current curve and the nanotube morphology

The formation mechanism of anodic TiO2 nanotubes remains to be unclear till now. Many researchers study the influence of temperatures above 0 °C instead of below 0 °C. Few papers before have explained the relationship between the current-time curve and the morphology of the nanotubes. In this study, the innovative 'oxygen bubble model' and the ionic current and electronic current theories were introduced to explain the growth of nanotubes below 0 °C. The length of anodic TiO2 nanotubes at 15 °C, 0 °C, -10 °C were 1.28 μm, 0.93 μm and 0.21 μm, respectively, but the diameter of anodic TiO2 nanotubes was almost the same, at about 164 nm. When the temperature was low, the magnitude of electronic current and the ionic current was small, the mold effect was weak and nanotubes could not be formed. At the same time, this study shows that the dissolution reaction of the field-assisted solution theory has no electron gain or loss, and it has nothing to do with the current, which negates the field-assisted dissolution theory. A novel two-step anodization was used to verify the conclusion. It was found that nanotubes could be obtained when the anodizing current was decreasing or increasing. Also, ginseng-shaped nanotubes are formed at a particular voltage sequence. Based on the 'oxygen bubble model' and the ionic current and electronic current theories, the formation process of nanotubes of two-step anodization is explained clearly.

Incorporation of Ions into Nanostructured Anodic Oxides-Mechanism and Functionalities

Anodic oxidation of metals leads to the formation of ordered nanoporous or nanotubular oxide layers that contribute to numerous existing and emerging applications. However, there are still numerous fundamental aspects of anodizing that have to be well understood and require deeper understanding. Anodization of metals is accompanied by the inevitable phenomenon of anion incorporation, which is discussed in detail in this review. Additionally, the influence of anion incorporation into anodic alumina and its impact on various properties is elaborated. The literature reports on the impact of the incorporated electrolyte anions on photoluminescence, galvanoluminescence and refractive index of anodic alumina are analyzed. Additionally, the influence of the type and amount of the incorporated anions on the chemical properties of anodic alumina, based on the literature data, was also shown to be important. The role of fluoride anions in d-electronic metal anodizing is shown to be important in the formation of nanostructured morphology. Additionally, the impact of incorporated anionic species, such as ruthenites, and their influence on anodic oxides formation, such as titania, reveals how the phenomenon of anion incorporation can be beneficial.

Evidence of oxygen bubbles forming nanotube embryos in porous anodic oxides

Anodic TiO2 nanotubes have been studied widely for two decades because of their regular tubular structures and extensive applications. However, the formation mechanism of anodic TiO2 nanotubes remains unclear, because it is difficult to find convincing evidence for popular field-assisted dissolution or field-assisted injection theories and the oxygen bubble model. Here, in a bid to find direct evidence that oxygen bubbles form nanotube embryos, a new method is applied to handle this challenge. Before nanotube formation, a dense cover layer was formed to make nanotubes grow more slowly. Many completely enclosed nanotube embryos formed by oxygen bubbles were found beneath the dense cover layer for the first time. The formation of these enclosed and hollow gourd-shaped embryos is convincing enough to prove that the nanotubes are formed by the oxygen bubble mold, similar to inflating a football, rather than by field-assisted dissolution. Based on the 'oxygen bubble model' and ionic current and electronic current theories, the formation and growth process of nanotube embryos is explained clearly for the first time. These interesting findings indicate that the 'oxygen bubble model' and ionic current and electronic current theories also apply to anodization of other metals.

Fabrication and application of nanoporous anodic aluminum oxide: a review

Due to the unique optical and electrochemical properties, large surface area, tunable properties, and high thermal stability, nanoporous anodic aluminum oxide (AAO) has become one of the most popular materials with a large potential to develop emerging applications in numerous areas, including biosensors, desalination, high-risk pollutants detection, capacitors, solar cell devices, photonic crystals, template-assisted fabrication of nanostructures, and so on. This review covers the mechanism of AAO formation, manufacturing technology, the relationship between the properties of AAO and fabrication conditions, and applications of AAO. Properties of AAO, like pore diameter, interpore distance, wall thickness, and anodized aluminum layer thickness, can be fully controlled by fabrication conditions, including electrolyte, applied voltage, anodizing and widening time. Generally speaking, the pore diameter of AAO will affect its specific application to a large extent. Moreover, manufacturing technology like one/two/multi step anodization, nanoimprint lithography anodization, and pulse/cyclic anodization also have a major impact on overall array arrangement. The review aims to provide a perspective overview of the relationship between applications and their corresponding AAO pore sizes, systematically. And the review also focuses on the strategies by which the structures and functions of AAO can be utilized.

Post-annealing Effect on Optical and Electronic Properties of Thermally Evaporated MoOX Thin Films as Hole-Selective Contacts for p-Si Solar Cells

Owing to its large work function, MoOX has been widely used for hole-selective contact in both thin film and crystalline silicon solar cells. In this work, thermally evaporated MoOX films are employed on the rear sides of p-type crystalline silicon (p-Si) solar cells, where the optical and electronic properties of the MoOX films as well as the corresponding device performances are investigated as a function of post-annealing treatment. The MoOX film annealed at 100 °C shows the highest work function and proves the best hole selectivity based on the results of energy band simulation and contact resistivity measurements. The full rear p-Si/MoOX/Ag-contacted solar cells demonstrate the best performance with an efficiency of 19.19%, which is the result of the combined influence of MoOX's hole selectivity and passivation ability.

Bipolar Electrochemical Anodization Route for the Fabrication of Porous Anodic Alumina with Nanopore Gradients

Porous anodic alumina (PAA) films with homogeneous nanopores are achieved by traditional anodization. Here, we present a unique anodization technique based on bipolar electrochemistry to fabricate PAA films with nanopore gradients. In an oxalic acid solution dissolved in ethylene glycol, a stable bipolar anodization process is realized. The PAA film prepared at 280 V exhibits a continuous change in interpore distance from ∼171 to ∼83 nm over a range of only 5 mm on the aluminum sheet. Higher driving voltages lead to larger interpore distances and steeper nanopore gradients. Further, no direct electrical connection is required for this bipolar anodization.

Self-ordered nanospike porous alumina fabricated under a new regime by an anodizing process in alkaline media

High-aspect ratio ordered nanomaterial arrays exhibit several unique physicochemical and optical properties. Porous anodic aluminum oxide (AAO) is one of the most typical ordered porous structures and can be easily fabricated by applying an electrochemical anodizing process to Al. However, the dimensional and structural controllability of conventional porous AAOs is limited to a narrow range because there are only a few electrolytes that work in this process. Here, we provide a novel anodizing method using an alkaline electrolyte, sodium tetraborate (Na₂B₄O₇), for the fabrication of a high-aspect ratio, self-ordered nanospike porous AAO structure. This self-ordered porous AAO structure possesses a wide range of the interpore distance under a new anodizing regime, and highly ordered porous AAO structures can be fabricated using pre-nanotexturing of Al. The vertical pore walls of porous AAOs have unique nanospikes measuring several tens of nanometers in periodicity, and we demonstrate that AAO can be used as a template for the fabrication of nanomaterials with a large surface area. We also reveal that stable anodizing without the occurrence of oxide burning and the subsequent formation of uniform self-ordered AAO structures can be achieved on complicated three-dimensional substrates.

Regulation of endothelial functionality through direct and immunomodulatory effects by Ni-Ti-O nanospindles on NiTi alloy

Stent implantation has become one of the most widely used methods for the treatment of cardiovascular diseases. However, endothelial dysfunction and abnormal inflammatory response following implantation may lead to delayed re-endothelialization, resulting in vascular restenosis and stent thrombus. To address the concerns, we constructed nanospindles composed of TiO₂ and Ti₄Ni₂O through hydrothermal treatment of amorphous Ni-Ti-O nanopores anodically grown on NiTi alloy. The results show the treatment can significantly improve hydrophilicity and reduce Ni ion release, essentially independent of hydrothermal duration. The nanospindle surfaces not only promote the expression of endothelial functionality but also activate macrophages to induce a favorable immune response, downregulate pro-inflammatory M1 markers and upregulate pro-healing M2 markers. Moreover, nitric oxide (NO) synthesis, VEGF secretion, and migration of endothelial cells are enhanced after cultured in macrophage conditioned medium. The nanospindles thus are promising as vascular stent coatings to promote re-endothelization.

One-step preparation of C-doped TiO2 nanotubes with enhanced photocatalytic activity by a water-assisted method

In this paper, C-doped TiO₂ nanotubes were prepared in one-step by adding sucrose to water-assisted crystallization solution. The photocatalytic activity was obviously enhanced due to the decrease of the energy band gap after doping.

Highly Sensitive Interlocked Piezoresistive Sensors Based on Ultrathin Ordered Nanocone Array Films and Their Sensitivity Simulation

Achieving a continuously adjustable micro-nanostructure of sensing materials is crucial and still a challenge for the flexible pressure sensor. We proposed a new method to prepare ultrathin ordered nanocone array films by designing tunable tapered anodized aluminum oxide templates and to prepare highly sensitive flexible pressure sensors by the interlocking nanocone arrays. Meanwhile, the theoretical prediction model of the sensitivity of interlocked nanocone arrays is proposed, and its result shows that the resistance change rate is positively correlated with the height of interlocked nanocone arrays and the contact area between interlocked nanocones. According to the finite element simulation and experimental results, the interlocked ordered nanocone array pressure sensor exhibits a high sensitivity of 268.36 kPa^-1 in the pressure range of 0-200 Pa, an ultralow detection limit of 0.98 Pa, a fast response/recovery time of 48/56 ms, a low hysteresis of ±3.156%, stability under 5000 cycles of loading, and continuity and repeatability under different loads and loading speeds. Furthermore, the pressure sensor can accurately monitor weak wind velocities, wrist torsion and bending movement, and book opening and closing angles. The sensor has broad application prospects in wearable medical monitoring, electronic skin, and human-computer interaction.

Morphology and photoluminescence of nano-porous anodic alumina membranes obtained in oxalic acid at different anodization potentials

Porous Anodic alumina (PAA) with highly ordered pore geometry serves as an ideal template for future development of nanodevices. In the present work, PAA was prepared by varying anodization potential from 10 to 50 V in oxalic acid at 8 °C with a constant electrolyte concentration of 0.3 M. The influence of anodization potential on the structural and photoluminescence (PL) properties of PAA has been studied. The effect of anodization potential on the main pore characteristics of PAA such as pore diameter, interpore distance, pore density, porosity and circularity was studied. It was observed that circularity of PAA was nearly equal to one in the case of anodization potential of 40 V. Highest regularity ratio (RR) obtained for PAA formed in 40 V and it was calculated by WSxM software. It was noticed that with increasing anodization potential there is a slight change in PL spectra of PAA and shows a strong PL peak in blue region.