Effect of Reynolds number and lithium cation insertion on titanium anodization

Characterization and Comparison of WO3/WO3-MoO3 and TiO2/TiO2-ZnO Nanostructures for Photoelectrocatalytic Degradation of the Pesticide Imazalil

Tungsten oxide (WO3) and zinc oxide (ZnO) are n-type semiconductors with numerous applications in photocatalysis. The objective of this study was to synthesize and characterize different types of nanostructures (WO3, WO3-Mo, TiO2, and TiO2-ZnO) for a comparison of hybrid and pure nanostructures to use them as a photoanodes for photoelectrocatalytic degradation of emerging contaminants. With the aim of comparing the properties of both samples, field emission scanning electron microscopy (FE-SEM) and confocal laser-Raman spectroscopy were used to study the morphology, composition, and crystallinity, respectively. Electrochemical impedances, Mott-Schottky, and water splitting measurements were performed to compare the photoelectrochemical properties of photoanodes. Finally, the photoelectrocatalytic degradation of the pesticide Imazalil was carried out with the best optimized nanostructure (TiO2-ZnO).

Hydrodynamic control of titania nanotube formation on Ti-6Al-4V alloys enhances osteogenic differentiation of human mesenchymal stromal cells

In order to obtain bioactive bone-implant interfaces with enhanced osteogenic capacity, various approaches have been developed to modify surface physicochemical properties of bio-inert titanium and titanium alloys. One promising strategy involves fabricating highly ordered nanotubes (NT) on implant surfaces via electrochemical anodization. However, few studies have applied this technique to Ti-6Al-4V alloys most commonly adopted for the fabrication of osteo-integrated surfaces on orthopedic implants. In this study, we investigated the influence of electrolyte hydrodynamics to NT fabrication on Ti-6Al-4V in ethylene glycol based electrolyte and evaluated the osteogenic differentiation capacity of human mesenchymal stromal cells (hMSCs) on different diameter NT surfaces. Computational Fluid Dynamics (CFD) analysis was used to simulate electrolyte flow profiles under various stirring conditions (e.g. stirrer bar location and flow direction) and their correlation to NT formation. Polished Ti-6Al-4V disks (240 grit) were anodized at 20 and 40 V under optimal electrolyte flow conditions for comparison of NT diameter-controlled osteogenic differentiation and mineralization potential of hMSCs over 21 days culture in osteogenic media. Ti-6Al-4V surfaces anodized with 20 and 40 V resulted with NTs diameter approx. 39 and 83 nm, respectively. Electrolyte hydrodynamics (flow profile) significantly influenced the uniformity of NT formation. Here, a uniform velocity and shear stress profile at the surface promoted homogeneous NT growth, whereas large variation in either flow velocity or shear stress to the surface impaired mature NT formation. After 21 days of culture, fluorescence staining demonstrated significantly greater osteocalcin and osteopontin expression, and increased mineralized deposits (xylenol orange staining) on fluctuating NT surfaces anodized under 20 V (Ø 39 nm) relative to flat NT layer anodized with 40 V (Ø 83 nm) and polished controls. This study provides a systematic investigation of NT formation with respect to the electrolyte hydrodynamic effects to NT growth on Ti-6Al-4V alloys, demonstrating the feasibility of a one-step anodization process for generating uniform NT under optimal hydrodynamics. Optimized wavy micro-/nano-topography with Ø 39 nm NT stimulated osteogenic differentiation capacity of hMSCs on Ti-6Al-4V alloys and confirmed the potential application of anodization to improve osteo-integrative surfaces in orthopedic implants.

TiO₂ Nanostructures for Photoelectrocatalytic Degradation of Acetaminophen

Advanced oxidation processes driven by renewable energy sources are gaining attention in degrading organic pollutants in waste waters in an efficient and sustainable way. The present work is focused on a study of TiO₂ nanotubes as photocatalysts for photoelectrocatalytic (PEC) degradation of acetaminophen (AMP) at different pH (3, 7, and 9). In particular, different TiO₂ photocatalysts were synthetized by stirring the electrode at different Reynolds numbers (Res) during electrochemical anodization. The morphology of the photocatalysts and their crystalline structure were evaluated by field emission scanning electron microscopy (FESEM) and Raman confocal laser microscopy (RCLM). These analyses revealed that anatase TiO₂ nanotubes were obtained after anodization. In addition, photocurrent densities versus potential curves were performed in order to characterize the electrochemical properties of the photocatalysts. These results showed that increasing the Re during anodization led to an enhancement in the obtained photocurrents, since under hydrodynamic conditions part of the initiation layer formed over the tubes was removed. PEC degradation of acetaminophen was followed by ultraviolet-visible absorbance measurements and chemical oxygen demand tests. As drug mineralization was the most important issue, total organic carbon measurements were also carried out. The statistical significance analysis established that acetaminophen PEC degradation improved as hydrodynamic conditions linearly increased in the studied range (Re from 0 to 600). Additionally, acetaminophen conversion had a quadratic behavior with respect to the reaction pH, where the maximum conversion value was reached at pH 3. However, in this case, the diversity of the byproducts increased due to a different PEC degradation mechanism.

The effect of Reynolds number on TiO2 nanosponges doped with Li+ cations

TiO₂ nanosponges and nanotubes were doped with Li⁺, which resulted in higher photocurrent densities, especially in nanosponges.

Lithium intercalation and diffusion in TiO2 nanotubes: a first-principles investigation

The effective diffusion barriers between the outer and inner surfaces of the O_2c–TiO₂ NT can be as low as 0.53 eV.