Advanced electrochemical platform for determination of cytostatic drug flutamide in various matrices using a boron-doped diamond electrode

Synergistic innovation: MOF@GCN hybrid for electrochemical detection of flutamide-bridging experimental, computational, and real-world applications

Electrochemical sensors are at the forefront of analytical technology, offering remarkable sensitivity and rapid response for detecting a wide range of chemical and biological compounds. Herein, a bimetallic metal-organic framework (MOF) is engineered and combined with graphitic carbon nitride (GCN) to demonstrate exceptional electrochemical performance toward the anti-cancer drug flutamide. A simple solvothermal method is used to synthesize MOF and GCN. These materials are then used as precursors to synthesize the MOF@GCN nanocomposite via a sonication method. The formation of the nanocomposite is confirmed using various characterization techniques like UV-Vis spectroscopy, FTIR spectroscopy, XRD, XPS, TGA, SEM, and TEM. The electrochemical characterization is performed using EIS, and the electrochemical measurements are conducted using CV and LSV. The results obtained from the electrochemical parameters indicate good operational stability, high sensitivity, reliability, and excellent electrochemical conductivity. The LSV curves show linearity over a wide range of flutamide concentration levels (10 to 180 nM), a limit of detection of 17.56 nM, a limit of quantification of 53.23 nM, and an optimal sensitivity of 22.89 µA µM-1 cm-2. This electrical response of the sensor is attributed to the abundance of active sites, accelerated diffusion, and low rate of recombination. The real sample analysis conducted in biofluids and environmental samples also demonstrate good recovery for the flutamide analyte. The theoretical results obtained from the computational DFT analysis on the analyte are also in good agreement with the experimental results. In a wider perspective, the development of this electrochemical sensor promises significant advancements in health monitoring and environmental protection.

Follow up of the prostate cancer treatment based on a novel sensing method for anti-prostate cancer drug (flutamide)

In this work, novel modified electrode (MXene/MIL-101(Cr)/GCE) are manufactured through simple layer-by-layer immobilization procedure. The fabricated electrochemical sensor was utilized for electrochemical sensing of flutamide in biological fluids. The immobilization of both MXene and metal-organic framework (MOF) materials on the electrode surface could improve the electrochemical performance of the modified glassy carbon electrode (GCE) towards flutamide due to the synergic effects. The established sensor illustrated the significant sensing ability for the determination of flutamide. The influence of solution pH and volume ratio of MXene/MIL-101(Cr) on electrochemical performance of the modified GCE was researched and optimized. The sensor demonstrated a favorable detection limit of 0.009 μM and a linear range of 0.025-100 μM using differential pulse voltammetry (DPV) technique. The suggested assay illustrated an excellent sensing efficiency towards flutamide in body fluids with recoveries ranging from 97.7% to 102.5%, which indicates its potential in real matrices. In addition, the MXene/MIL-101(Cr)/GCE was illustrated some advantages including simple preparation, good selectivity and reproducibility, and rapid flutamide detection.

Electrochemical Detection of Flutamide by the Composite of Complex Based on Thiacalix[4]arene Derivatives and Reduced Graphene Oxide

In this paper, a thiacalix[4]arene complex [Zn2(TIT4A)L2]·4DMF·2CH3OH (H2L = 4,4'-oxybisbenzoic acid) (Zn-TIT4A-L) was synthesized by a solvothermal method. The composites were prepared by combining Zn-TIT4A-L with reduced graphene oxide (RGO), mesoporous carbon (MC), and multi-walled carbon nanotubes (MWCNTs), respectively. Three representative composites are Zn-TIT4A-L@RGO(1:1), Zn-TIT4A-L@MC(1:2), and Zn-TIT4A-L@MWCNT(1:2). X-ray diffraction and scanning electron microscopy characterized their structures and morphologies. The results showed that three composites were successfully prepared, and the crystals of the complex remained in the composites. The electrochemical properties of the composites were characterized by electrochemical impedance spectroscopy and cyclic voltammetry. The results indicated that they had good electrocatalytic activity and conductivity. Among them, Zn-TIT4A-L@RGO(1:1) had the best performance and was used for the quantitative detection of flutamide (FTA). The linear range of detection is 0.1-200 μM, and the limit of detection is 0.015 μM. At the same time, the sensor also had good reproducibility, anti-interference, and stability. The sensor was also used for the detection of FTA in lake water, human urine, and serum with a satisfactory recovery rate. The possible mechanism of electrochemical detection of FTA was also discussed.

Self assembled three dimensional β-Cu2V2O7 hierarchical flower decorated porous carbon: An efficient electrocatalyst for flutamide detection in biological and environmental samples

The serious situation mandates the use of anticancer drugs, which protect people all over the world from the growth of prostate cancer. In particular, excessive dosage and erroneous discharge of flutamide concentration cause make environmental pollution on the surface of the wastewater. In this study, the highly sensitive and selective electrochemical approach based on copper vanadium oxide decorated porous carbon (denoted as β-Cu₂V₂O₇/PC) composite modified glassy carbon electrode (GCE) has been developed and it was applied for sensitive detection of anticancer drug flutamide (FTM). Moreover, using the co-precipitation method, the flower-like β-Cu₂V₂O₇ hierarchical microstructure was synthesized, and through the wet chemical process, the β-Cu₂V₂O₇/PC composite was obtained. The resultant product was characterized by XRD, FTIR, RAMAN, XPS and structural morphology established by FESEM analysis. Besides that, the electrochemical characterization and properties were analyzed by cyclic voltammetry (CV) and amperometric (i-t) techniques. The β-Cu₂V₂O₇/PC/RDGCE had two linear ranges at 0.01-2.11 μM and 2.31-30.81 μM. The lower limits of detection and sensitivity were found at 0.62 nM (S/N = 3), and 24.33 μA μM^-1 cm^-2 respectively. The practicability test was applied for the determination of FTM in urine, blood serum and environmental aquatic fluid with satisfactory recovery obtained.

Nanomolar level detection of non-steroidal antiandrogen drug flutamide based on ZnMn2O4 nanoparticles decorated porous reduced graphene oxide nanocomposite electrode

Flutamide is a non-steroidal antiandrogen drug and widely used in the treatment of prostatic carcinoma. Nevertheless, the excessive intake and improper disposal could affect the living organisms. In this work, we have synthesized a new nanocomposite based on ZnMn₂O₄ nanoparticles and porous reduced graphene oxide nanosheets (ZnMn₂O₄-PGO) for the electrocatalytic detection of flutamide (FLU) drug. The crystallinity and morphological properties of ZnMn₂O₄-PGO composite examined by different characterization techniques such as X-ray diffraction, Raman spectroscopy and so on. The fabricated ZnMn₂O₄-PGO nanocomposite modified electrode exhibited superior electrocatalytic performance to FLU drug in an optimized pH electrolyte. Fascinatingly, the electrode received a wide linear range (0.05-3.5 µM) with limit of detection of 8 nM. Besides, the developed ZnMn₂O₄-PGO nanocomposite electrode showed good sensitivity 1.05 µAµM^-1 cm^-2 and excellent selectivity for FLU detection in presence of various interfering species. A developed disposable electrode was scrutinized to determine FLU level in human urine samples by spiking method and the results achieved good recoveries in real sample analysis.

A molecularly imprinted poly 2-aminophenol-gold nanoparticle-reduced graphene oxide composite for electrochemical determination of flutamide in environmental and biological samples

A selective and sensitive electrochemical sensor based on reduced graphene oxide, gold nanoparticles, and molecularly imprinted poly 2-aminophenol was developed for electrochemical determination of flutamide in environmental and biological samples. The composite fabrication was electrochemically carried out and the composite was characterized by Fourier transform infrared, proton and carbon nuclear magnetic resonance, field emission scanning electron microscopy, and energy-dispersive X-ray spectrometry. The spectroscopic results showed that polymerization of molecularly imprinted poly 2-aminophenol took place through a ladder structure system. After optimization of effective parameters on the response of the sensor, the obtained linear range, relative standard deviation (for a concentration of 50 μg L^-1 with five replicates) and limit of quantification for flutamide determination were determined to be 2-375 μg L^-1, 1.54% and 0.8 μg L^-1, respectively. The results showed that the application of poly 2-aminophenol in the structure of the proposed sensor using a molecular imprinting approach made the sensor highly selective toward flutamide, distinguishing it from similar nitro-containing compounds. The prepared sensor was successfully utilized to analyze environmental water and urine samples. The obtained results showed that the proposed method is in agreement with the HPLC method and can be used as a reliable alternative method for the analysis of flutamide.

Boron-Doped Diamond Electrodes: Recent Developments and Advances in View of Electrochemical Drug Sensors

Conductive boron-doped diamond (BDD), in addition to its superior material properties, offers many important advantages that make it an interesting material for electroanalytical studies. It has been considered as an excellent electrode material for electrooxidation of drug active compounds in their dosage forms or in biological materials due to its good physical and chemical properties. It contains not only the largest solvent working potential window compared to other electrode materials, but also it has low background and capacitive currents; lower problems with passivation and it has the ability to withstand extreme potentials, corrosive, and high temperature/pressure environments. The aim of this review is not only to provide a state-of-the-art of diamond electrochemistry but also to serve as a reference point for any researcher wishing to commence work with diamond electrodes and understand electrochemical data. Therefore, it is focused on the carbon-based materials, electrochemical properties of the BDD film electrode, its fundamental research, and its electrochemical pretreatment process are discussed in detail. In this case, there are important studies to show the effective BDD drug sensors for the detection and determination of drugs and the present review critically summarizes the available data in this field between 2015 and 2020.

Gold Nanoparticle Embedded on a Reduced Graphene Oxide/polypyrrole Nanocomposite: Voltammetric Sensing of Furazolidone and Flutamide

A new electrochemical sensor has been constructed based on the in situ preparation of gold nanoparticle embedded on reduced graphene oxide and polypyrrole nanotube (AuNP@rGO/PPyNT) composite through a nanosecond laser-induced heating technique. The as-prepared composite is used for individual as well as the simultaneous electrochemical determination of chemotherapy drug (furazolidone, FU) and anticancer drug (flutamide, FLT). The composite was analyzed by X-ray Diffraction, scanning electron microscopy/energy-dispersive X-ray analysis, transmission electron microscopy, Raman spectrometry, and X-ray photoelectron spectroscopy analysis, thus confirming the successful synthesis of this composite and its physical features. The modified AuNP@rGO/PPyNT electrode was examined through cyclic voltammetry and differential pulse voltammetry (DPV) methods in pH 7.0 for the determination of FU and FLT in individual, simultaneous, and mixed systems. The fabricated sensor showed wide linear responses (0.01-1080.11 μM and 0.01-1214.11 μM) of analytes, with the lower limits of detection of 2.3 and 2.45 nM and higher sensitivity of 53.75 and 50.06 μA μM^-1 cm^-2, respectively. Furthermore, the constructed sensor demonstrates higher stability, reproducibility, and repeatability, and is effectively applied for the analysis of FU and FLT content in the human serum sample analysis with satisfactory recovery.

Nanomaterial-based electrochemical sensors and biosensors for the detection of pharmaceutical compounds

The surging growth of the pharmaceutical industry is a result of the rapidly increasing human population, which has inevitably led to new biomedical and environmental issues. Aside from the quality control of pharmaceutical production and drug delivery, there is an urgent need for precise, sensitive, portable, and cost-effective technologies to track patient overdosing and to monitor ambient water sources and wastewater for pharmaceutical pollutants. The development of advanced nanomaterial-based electrochemical sensors and biosensors for the detection of pharmaceutical compounds has garnered immense attention due to their advantages, such as high sensitivity and selectivity, real-time monitoring, and ease of use. This review article surveys state-of-the-art nanomaterials-based electrochemical sensors and biosensors for the detection and quantification of six classes of significant pharmaceutical compounds, including anti-inflammatory, anti-depressant, anti-bacterial, anti-viral, anti-fungal, and anti-cancer drugs. Important factors such as sensor/analyte interactions, design rationale, fabrication, characterization, sensitivity, and selectivity are discussed. Strategies for the development of high-performance electrochemical sensors and biosensors tailored toward specific pharmaceuticals are highlighted to provide readers and scientists with an extensive toolbox for the detection of a wide range of pharmaceuticals. Our aims are two-fold: (i) to inspire readers by further elucidating the properties and functionalities of existing nanomaterials for the detection of pharmaceuticals; and (ii) to provide examples of the potential opportunities that these devices have for the advanced sensing of pharmaceutical compounds toward safeguarding human health and ecosystems on a global scale.

Performance of chitosan polymer as platform during sensors fabrication and sensing applications

Chitosan is an important polymer produced from deacetylation of several sea and insects crusts. Due to its environmental fate and biological biocompatibility, it can be used in several biological and environmental applications. Sensing of biological compounds in human bodies and also in serum, blood, and different body fluids has found an important application instead of direct determination of the body fluids using complicated tools. Sensing process of biological compounds during bio-analysis of the biological systems, especially human fluids lack of several parameters including: high sensitivity, repeatability, speed of analysis and biocompatibility of the used analytical methods, especially in-vivo analysis. That was due to the time between sample handling and sample determination can change various components and concentrations of the bio-compounds. The need for in-situ analysis was directed the researchers for biosensors to overcome the upgrading problems of bio-analysis. Biosensors were the future of this issue. Chitosan can reserve as great platform for fabrication of different sensors to determine the elements, compounds and body bioactive compounds. The presence of different terminal amino and hydroxyl groups within chitosan framework facilitates the immobilization of different biomarkers to be used as sensing elements for the determined compounds. The use of chitosan as sensors platform was enhanced by using chitosan in its nanoforms.

Ultrasonication and hydrothermal assisted synthesis of cloud-like zinc molybdate nanospheres for enhanced detection of flutamide

Ultrasonication is one of the emerging probes for nanoparticles synthesis as well as promoting the material property by treasuring the precious time during a chemical reaction. In this present work, we successfully designed a cloud-like α-ZnMoO₄ nanospheres (ZMNS) using ultrasound assistance (bath sonication with the power of 60 W and frequency of 37/80 kHz) hydrothermal method for catalyzing the effective electrochemical determination of anti-androgen drug candidate flutamide (FLT). The crystallinity and phase purity were investigated using powder X-ray diffractometric analysis. The FTIR and Raman spectra information were compared to detect the possible bonding in ZMNS. The texture and surface morphology were studied using Field emission scanning electron microscope and High-resolution Transmission electron microscope images. The presence of the elements (Zn, Mo and O) and the absence of any other impurities were monitored and confirmed using EDAX analysis. The fabrication of ZMNS modified GCE was performed carefully. Additionally, the ZMNS modified glassy carbon electrode (GCE) exhibits superior electrocatalytic activity by means of higher cathodic peak current towards the detection of FLT. The fashioned electrode attained two wide linear response ranges (0.1 to 73 µM; 111 to 1026 µM) with a lower detection limit of about 33 nM correspondingly. Furthermore, the fabricated sensor displayed excellent sensitivity of 1.095 µA µM^-1 cm^-2 and good selectivity for FLT sensing even in the existence of similar interfering compounds and biomolecules. Along with that, the designed sensor executed noticeable reproducibility, repeatability, and enduring stability.

Carboxymethyl-botryosphaeran stabilized carbon nanotubes aqueous dispersion: A new platform design for electrochemical sensing of desloratadine

The polysaccharide carboxymethyl-botryosphaeran (CMB) was used to improve the dispersion of multi-walled carbon nanotubes (MWCNTs) in water. This feature was applied in modifying a glassy carbon electrode (GCE) to construct a sensitive voltammetric sensor for the determination of desloratadine (DESL), a tricyclic antihistamine. The morphology and spectroscopic behavior of the sensor were evaluated. The modified sensor was characterized as homogeneous, and presented a higher electroactive area and a lower charge transfer resistance compared to the unmodified GCE. Using linear sweep voltammetry at 25 mV s^-1, the developed sensor presented a sensitivity of 1.018 μA L μmol^-1 in the linear working range of 1.99-32.9 μmol L^-1, with a detection limit of 0.88 μmol L^-1 of DESL in 0.10 mol L^-1 potassium hydrogen-phosphate solution (pH 8.0). In addition, the sensor showed excellent repeatability with a relative standard deviation of only 1.02% for a sequence of 10 measurements. The sensor was successfully applied in the analysis of pharmaceutical preparations containing DESL, with equivalent results compared to a validated spectrophotometric method at the 95% confidence level. The sensor was also employed in the analysis of a spiked sample of DESL in rat serum.

Enhanced electrochemical supercapacitor performance with a three-dimensional porous boron-doped diamond film

A three-dimensional porous boron-doped diamond film is developed to enhance the electrochemical performance of supercapacitors in a wide potential window.

Advanced oxidation process-mediated removal of pharmaceuticals from water: A review

Pharmaceuticals, which are frequently detected in natural and wastewater bodies as well as drinking water have attracted considerable attention, because they do not readily biodegrade and may persist and remain toxic. As a result, pharmaceutical residues pose on-going and potential health and environmental risks. To tackle these emerging contaminants, advanced oxidation processes (AOPs) such as photo-Fenton, sonolysis, electrochemical oxidation, radiation and ozonation etc. have been applied to remove pharmaceuticals. These processes utilize the high reactivity of hydroxyl radicals to progressively oxidize organic compounds to innocuous products. This review provides an overview of the findings from recent studies, which have applied AOPs to degrade pharmaceutical compounds. Included is a discussion that links various factors of TiO₂-mediated photocatalytic treatment to its effectiveness in degrading pharmaceutical residues. This review furthermore highlights the success of AOPs in the removal of pharmaceuticals from different water matrices and recommendations for future studies are outlined.