Tuberose surface architecture of Sr(OH)2 film as supercapacitive electrode

Enriching Nano-Heterointerfaces in Proton Conducting TiO2-SrTiO3@TiO2 Yolk-Shell Electrolyte for Low-Temperature Solid Oxide Fuel Cells

A challenging task in solid oxide fuel cells (SOFCs) is seeking for an alternative electrolyte, enabling high ionic conduction at relatively low operating temperatures, i.e., 300-600 °C. Proton-conducting candidates, in particular, hold a significant promise due to their low transport activation energy to deliver protons. Here, a unique hierarchical TiO2-SrTiO3@TiO2 structure is developed inside an intercalated TiO2-SrTiO3 core as "yolk" decorating densely packed flake TiO2 as shell, creating plentiful nano-heterointerfaces with a continuous TiO2 and SrTiO3 "in-house" interfaces, as well the interfaces between TiO2-SrTiO3 yolk and TiO2 shell. It exhibits a reduced activation energy, down to 0.225 eV, and an unexpectedly high proton conductivity at low temperature, e.g., 0.084 S cm-1 at 550 °C, confirmed by experimentally H/D isotope method and proton-filtrating membrane measurement. Raman mapping technique identifies the presence of hydrogenated HO─Sr bonds, providing further evidence for proton conduction. And its interfacial conduction is comparatively analyzed with a directly-mixing TiO2-SrTiO3 composite electrolyte. Consequently, a single fuel cell based on the TiO2-SrTiO3@TiO2 heterogeneous electrolyte delivers a good peak power density of 799.7 mW cm-2 at 550 °C. These findings highlight a dexterous nano-heterointerface design strategy of highly proton-conductive electrolytes at reduced operating temperatures for SOFC technology.

Intrinsically radiopaque and antimicrobial cellulose based surgical sutures from mechanically powerful Agave sisalana plant leaf fibers

The judicious configuration of a flexible radiopaque suture would be exemplary to facilitate effortless tracking and precise diagnosis of the sutured surgical site by various X-ray assisted imaging modalities and simultaneously serve as a complementary tool for monitoring the fate of the suture material during the post-operative course. A unique radiopaque cellulose based surgical suture (RF) with good mechanical properties was developed by strategically controlled mercerization and bleaching of mechanically strong natural cellulosic fibers extracted from Agave sisalana plant leaves followed by the facile dip-coating of SrO integrated polylactic acid (PLA). RF exhibited admirable straight-pull tensile strength (184 MPa) and commendable contrast enhancement (277.4%) under digital X-ray radiographic imaging which was further validated by micro-CT analysis. Further, RF has a controlled hydrolytic degradation profile favorable for surgical suturing (mass loss ∼22% in 28 days). The microporous surface architecture of RF (pore size < 10 μm) as a result of SrO-PLA coating enabled the loading of antibiotic (ciprofloxacin) deep inside the pores with a cumulative release of 24% at 28 days under physiological conditions substantiating its feasibility to be used as an efficient antimicrobial suture (CRF) that prevents possible bacterial infections at the surgical site. This has been demonstrated by antibacterial disc diffusion assay performed against two Gram-positive and two Gram-negative bacterial strains. Significantly, both RF and CRF are highly biocompatible as confirmed by MTT assay and F-actin staining. Hence, CRF would be a good biocompatible suture candidate holding good tensile properties, exceptional antimicrobial property and intrinsic radiopacity retention for a period >28 days.

A Study on Synthesis and Characterization of Dy-Doped La0.6Sr0.4Co0.2Fe0.8O3−δ via the Coprecipitation Method

The perovskite Lanthanum Strontium Cobalt Ferrite (LSCF) is investigated as the cathode material used in intermediate-temperature solid oxide fuel cells (IT-SOFCs). In the present study, La0.6−xDyxSr0.4Co0.2Fe0.8O3−δ (x = 0, 0.3, 0.6) was synthesized through the coprecipitation method. The obtained precipitate was calcined at 500, 700, 900, and 1000°С. Phase characterization of the synthesized LSCF and LDySCF powder before and after heat treatment at 700°С was carried out by X-ray diffraction (XRD) analysis. XRD patterns revealed that the perovskite phase was obtained at 700°С in all calcined samples. Chemical bond study to investigate the synthesis process was conducted using the Fourier transform infrared spectroscopy technique. Thermal analysis of DTA and TG has been utilized to investigate how the calcination temperature affects the perovskite phase formation. According to the STA results, the perovskite phase formation started at 551°С and completed at 700°С. The density values of synthesized powders were 6.10, 6.11, and 6.37 g·cm−3for the undoped and doped samples calcined at 700°С. Powder morphology was studied by field emission scanning electron microscopy (FE-SEM). The micrographs showed the spherical-shaped particles with the average particle size of 24–131 nm.