Three-dimensional nanocomposite of graphene/MWCNT hydrogel grafted with Ni–Co hydroxide nanorods as high-performance electrode for asymmetric supercapacitor

One-pot synthesis of graphene hydrogel/M (M: Cu, Co, Ni) nanocomposites as cathodes for electrochemical removal of rifampicin from polluted water

Nowadays, the removal of pharmaceutical contaminants from water resources and wastewater is of great importance due to environmental and health issues. Over the decades, various methods have been reported to remove pollutants from wastewater. Among the developed methods, advanced oxidation processes (AOPs) have received significant attention from researchers. In this study, we report the one-pot synthesis of graphene hydrogel-metal (GH-M, M: Co, Ni, Cu) nanocomposites via the combination of polyol and hydrothermal methods. The structure of the resulting nanocomposites was examined by transmission electron microscopy (TEM), inductively coupled plasma-mass spectroscopy (ICP-MS), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), and Raman spectroscopy methods. Afterward, as-prepared GH-Cu, GH-Co, and GH-Ni nanocomposites were used to prepare cathodes for the electro-Fenton (EF) process to remove rifampicin (RIF) from polluted water. The effect of operational parameters, including current density (mA/cm²), initial pH, initial RIF concentration (mg/L), and process time (min) was investigated via response surface methodology (RSM). The optimal values for current density, pH, initial RIF concentration, and process time using GH-Ni as cathode were 30 mA/cm², 5, 30 mg/L, and 90 min, respectively. The results at optimal values showed that the maximum RIF removal efficiency for GH-Cu, GH-Co, and GH-Ni cathodes was 90.47, 92.60, and 93.69%, respectively. Brunauer Emmett Teller (BET), atomic force microscopy (AFM), energy-dispersive X-ray (EDX), and cyclic voltammetry (CV) analyses were performed to investigate the performance of the cathodes for the RIF removal. Finally, total organic carbon (TOC), gas chromatography-mass spectrometry (GC-MS), and atomic absorption spectroscopy (AAS) analyses were performed for further investigation of the RIF removal from polluted water. The results claimed that one-pot synthesized GH-M cathodes can effectively remove RIF from polluted water through EF process.

Polyethylene-Derived Activated Carbon Materials for Commercially Available Supercapacitor in an Organic Electrolyte System

We fabricated high-performance supercapacitors based on activated carbons (AC) derived from Polyethylene (PE), which is one of the most abundant plastic materials worldwide. First, PE carbons (PEC) were prepared via sulfonation, which is reported solution for successful carbonization of innately non-carbonizable PE. Then, we explored the physico-electrical changes of PECs upon a chemical activation process. Interestingly, upon the chemical activation, PECs were converted ACs with a large surface area and high crystallinity at the same time. Subsequently, we exploited PE-derived ACs (PEAC) as electrode materials for supercapacitors. Resultant supercapacitors based on PEACs exhibited impressive performance. When compared to supercapacitors based on YP50f, a representative commercial ACs, devices using PEACs presented considerably good capacitance, low resistance, and great rate capability. Specifically, the retention rate of devices using PEACs was significantly higher than that of YP50f-based devices. At the high-rate of charge-discharge situation reaching 7 A g^-1 , the capacitance of supercapacitors using PEACs was about 70% higher than that of YP50f-based devices. We assumed the carbon structure accompanying both large surface area and high conductivity endowed a great electrochemical performance at the high current operating conditions. Therefore, it is envisioned PE might be a viable candidate electrode material for commercially available supercapacitors. This article is protected by copyright. All rights reserved.

Engineering Co3O4/MnO2 nanocomposite materials for oxygen reduction electrocatalysis

Stable and active electrocatalysts preparation for the oxygen reduction reaction (ORR) is essential for an energy storage and conversion materials (e.g. metal-air batteries). Herein, we prepared a highly-active MnO₂ and Co₃O₄/MnO₂ nanocomposite electrocatalysts using a facial co-precipitation approach. The electrocatalytic activity was examined in alkaline media with LSV and CV. Additionally, the physicochemical characteristics of the MnO₂ and Co₃O₄/MnO₂ composite materials were studied via SEM, XRD, BET, UV-Vis, TGA/DTA, ICP-OES and FTIR. Morphological studies indicated that a pure MnO₂ has a spherical flower-like architecture, whereas Co₃O₄/MnO₂ nanocomposites have an aggregated needle-like structure. Moreover, from the XRD investigation parameters such as the dislocation density, micro-strain, and crystallite size were analyzed. The calculated energy bandgaps for the MnO₂, Co₃O₄/MnO₂-1-5, and Co₃O₄/MnO₂-1-1 nanocomposites were 3.07, 2.6, and 2.3 eV, correspondingly. The FTIR spectroscopy was also employed to study the presence of M-O bonds (M = Mn, Co). The thermal gravimetric investigation showed that the Co₃O₄/MnO₂ nanocomposite materials exhibited improved thermal stability, confirming an enhanced catalytic activity of ORR for MnO₂/Co₃O₄-1-1 composite materials for ORR. These results confirm that the prepared Co₃O₄/MnO₂ composite materials are promising air electrode candidates for the energy storage and conversion technologies.