Effect of acid rain on building material of the El Tajín archaeological zone in Veracruz, Mexico

Quantifying Decay Due to Wet Atmospheric Deposition on Basalt

The study of building materials is important for a better conservation of built heritage. Worldwide, volcanic stones (including basalt, andesite and dacite) are among the least studied building materials. In this research, the decay of a red basalt due to wet atmospheric deposition was studied. Red basalt was exposed to artificial rain solutions, prepared from rain samples collected weekly from 2014-2019. In this research, the decay of stone-built heritage was indirectly studied emulating wet atmospheric accelerated weathering under three different volume weighted mean (VWM) compositions: global, acid and no-acid categories. Lixiviates were analyzed to better understand the deterioration mechanisms taking place inside the material. Decay was quantified as mass difference, water absorption capacity (WAC) and open porosity (OP) changes. Results show that the methodology used is suitable to research the decay of built heritage. The studied basalt is indeed prone to decay by wet atmospheric deposition. The main decay mechanisms are the washing of insoluble compounds, dissolution of minerals, salt crystallization and cation exchange. WAC and OP showed promising results of their appropriateness as monitoring variables of decay in situ. Acid conditions produce the most severe decay, but Ph effect is not as important as precipitation volume. Non-linear equations relating volume of precipitation with mass difference in red basalt are presented.

Density Functional Theory (DFT) as a Nondestructive Probe in the Field of Art Conservation: Small-Molecule Adsorption on Aragonite Surfaces

Humans have incorporated minerals in objects of cultural heritage importance for millennia. The surfaces of these objects, which often long outlast the humans that create them, are undeniably exposed to a diverse mixture of chemicals throughout their lifetimes. As of yet, the art conservation community lacks a nondestructive, accurate, and inexpensive flexible computational screening method to evaluate the potential impact of chemicals with art, as a complement to experimental studies. In this work, we propose periodic density functional theory (DFT) studies as a way to address this challenge, specifically for the aragonite phase of calcium carbonate, a mineral that has been used in pigments, marble statues, and limestone architecture since ancient times. Computational models allow art conservation scientists to better understand the atomistic impact of small-molecule adsorbates on common mineral surfaces across a wide variety of environmental conditions. To gain insight into the surface adsorption reactivity of aragonite, we use DFT to investigate the atomistic interactions present in small-molecule-surface interfaces. Our adsorbate set includes common solvents, atmospheric pollutants, and emerging contaminants. Chemicals that significantly disrupt the surface structure such as carboxylic acids and sulfur-containing molecules are highlighted. We also focus on comparing adsorption energies and changes in surface bonds, which allows for the identification of key features in the electronic structure presented in a projected-density-of-state analysis. The trends outlined here will guide future experiments and allow art conservators to gain a better understanding of how a wide range of molecules interact with an aragonite surface under variable conditions and in different environments.

The influence of marine environment on the conservation state of Built Heritage: An overview study

Marine aerosol is a chemical complex system formed by inorganic salts and organic matter, together with airborne particulate matter from the surrounding environment. The primary particles transported in the marine aerosol can experiment different chemical reactions in the atmosphere, promoting the so-called Secondary Marine Aerosol particles. These kinds of particles (nitrates, sulfates, chlorides etc.), together with the natural crustal or mineral particles and the metallic airborne particulate matter emitted by anthropogenic sources (road traffic, industry, etc.) form clusters which then can be deposited on building materials from a specific construction following dry deposition processes. Apart from that, the acid aerosols (e.g. CO₂, SO₂, NO_X, etc.) present in urban-industrial environments, coming also from anthropogenic sources, can be deposited in the buildings following dry or a wet deposition mechanisms. The interactions of these natural and anthropogenic stressors with building materials can promote different kind of pathologies. In this overview, the negative influence of different marine environments (direct or diffuse influence), with or without the influence of an urban-industrial area (direct or diffuse), on the conservation state of historical constructions including a wide variety of building materials (sandstones, limestones, artificial stones, bricks, plasters, cementitious materials, etc.) is presented.

Issues, Impacts, and Mitigations of Carbon Dioxide Emissions in the Building Sector

Climate change has become a considerable concern for humanity during this anthropocentric era. Scientists believe that the rate of global warming and climate change varies directly with the increase in the concentration of greenhouse gases, particularly carbon dioxide. Urbanization is happening at a higher rate in this era than in any other generation. It was reported that the building sector plays a critical role in the emission of carbon dioxide (CO2) into the atmosphere. Construction of buildings, operation, and utilization of the built environment has led to emissions of a large number of CO2 into the ambient air. Various issues and challenges arise from the building sector in reducing CO2 emissions. The exploitation of non-renewable energy resources, poor building design, and lack of sustainability consideration in urbanization has been holding back CO2 emission mitigation measures in the building sector. Therefore, CO2 emission mitigation plans and schemes are necessary alongside standardized frameworks and guidelines. The strategies to reduce CO2 in the building sector are enforcing standards and policy, conducting impact assessment, adopting low carbon technology, and restricting energy utilization. All stakeholders must play their roles efficiently to reduce CO2 emissions and aid in the fight against climate change.

Sulfur and nitrogen compounds in wet atmospheric deposition on the coast of the Gulf of Mexico from 2003 to 2015

The Gulf of Mexico region has important sources of acid rain precursors, located in all of the countries; U.S., Mexico and Cuba, and so it is very important to study the chemical composition of the wet atmospheric deposition in all coastal areas. For many years along the U.S. Gulf Coast, acidic precipitation has been measured. Measurements along the Mexican Gulf Coast were begun in 2003. The aim of this study was to evaluate pH, sulfate, nitrate and ammonium concentrations in wet atmospheric deposition, collected daily from 2003 to 2015 at La Mancha (LM), Veracruz and compare the values with the National Atmospheric Deposition Program (NADP) sampling sites located along the U.S. coast of the Gulf of Mexico. The annual Volume Weighted Mean (VWM) pH in wet deposition at La Mancha site ranged from 4.81 to 5.40, which is similar to the U.S. Gulf sites. Additionally, the annual VWM SO₄^2- concentration was from 15 to 31 μeq/L, which is higher than the U.S. sites. Annual VWM NO₃^- concentrations were from of 3.5 to 15 μeq/L, which is lower than all the U.S. sites. At the Mexican site, the SO₄^2-/NO₃^- ratio was 4.90 and higher than all of the U.S. sites, which were between 1.03 and 2.38. For LM, the median NH₄⁺/NO₃^- ratio was 0.77, similar to the Florida sites (0.53-0.91), and below the values measured for Louisiana and Texas (1.07-1.5). The Hybrid Single Particle Lagrangian Integrated Trajectory Model (HYSPLIT) was applied in order to identify the emission sources for the pollutants seen at LM. Trajectories showed an important transport to LM from the East (open water) during the rainy season. The region located East of La Mancha shows offshore petroleum operations as sources of acid rain precursors and deposition of acidifying and nitrogen containing compounds. It is important to consider the sulfur dioxide emission sources in the Mexico Gulf region, and to extend the atmospheric deposition sampling to other sites along the Mexican Gulf coast and Cuba.

Mechanical Behavior of Brick Masonry in an Acidic Atmospheric Environment

In order to evaluate the deterioration regularity for the mechanical properties of brick masonry due to acid rain corrosion, a series of mechanical property tests for mortars, bricks, shear prisms, and compressive prisms after acid rain corrosion were conducted. The apparent morphology and the compressive strength of the masonry materials (cement mortar, cement-lime mortar, cement-fly ash mortar, and brick), the shear behavior of the masonry, and the compression behavior of the masonry were analyzed. The resistance of acid rain corrosion for the cement-lime mortar prisms was the worst, and the incorporation of fly ash into the cement mortar did not improve the acid rain corrosion resistance. The effect of the acid rain corrosion damage on the mechanical properties for the brick was significant. With an increasing number of acid rain corrosion cycles, the compressive strength of the mortar prisms, and the shear and compressive strengths of the brick masonry first increased and then decreased. The peak stress first increased and then decreased whereas the peak strain gradually increased. The slope of the stress-strain curve for the compression prisms gradually decreased. Furthermore, a mathematical degradation model for the compressive strength of the masonry material (cement mortar, cement-lime mortar, cement-fly ash mortar, and brick), as well as the shear strength attenuation model and the compressive strength attenuation model of brick masonry after acid rain corrosion were proposed.

Biodesulfurization of Petroleum Distillates—Current Status, Opportunities and Future Challenges

Sulfur oxide (SO2) and hydrogen sulfide (H2S) are considered as one of the major air pollutants in the world today. In addition, high sulfur levels in petroleum distillates can promote the deactivation of catalysts through poisoning in fluidized catalytic cracking (FCC) during hydrocracking of the heavy distillates to lighter ones. The presence of high sulfur-containing compounds in the process streams could cause corrosion of piping and fittings and equipment, thereby damaging the pipelines and leading to air emissions of sulfur-containing compounds, which are undesirable for mankind and his environment. In many cases, a large quantity of SOx is released into the atmosphere when petroleum distillates that contain substantial amount of sulphur-containing compounds are used as fuel and combust. In this article, a short overview of different desulfurization methods that are employed to remove sulfur from petroleum distillates is provided. In particular, the review concentrates on biodesulfurization technique. In addition, this article intends to provide its readers current status of biodesulfurization (BDS). It critically analyses the trend in the development of the technology to showcase its strength and weakness that could pave a way for future opportunities. Approaches that are suitable to remediate sulfur-contaminated environment are discussed as well. Lastly, speculations on future directions or opportunities that require exploration are provided as a way of provoking the thoughts of researchers in this field.

The influence of rainwater composition on the conservation state of cementitious building materials

Rainwater is one of the main pollution tracers around the world. There are many reasons that can explain the presence of high concentrations of certain hazardous elements (HEs) in the rainwater (traffic, marine port activities, industry, etc.). In this work, rainwater samples were collected at six different locations in the Metropolitan Bilbao (Basque Country, north of Spain) during November 2014. HE concentrations were determined by means of inductively coupled plasma mass spectrometry (ICP-MS) and anions by ion chromatography. The pH and redox potential values on these samples were also assessed. According to the obtained results, different trends along the estuary of Bilbao have been observed. To corroborate some hypothesis, thermodynamic simulations and correlation analyses were also carried out using quantitative data. These trends are closely related to the surrounding pollution and marine influence. Finally, in order to ascertain the influence of the Metropolitan Bilbao rainwater on buildings materials, a recent construction was characterized. Using techniques such as Scanning Electron Microscopy coupled with Energy Dispersive X-Ray Spectroscopy (SEM–EDS) and Raman Spectroscopy, different types of sulfates and nitrates were observed.

Physical and Chemical Components of Cuba’s Rain: Effects on Air Quality

The objective of this study was to analyze the influence of the physical and chemical components of rain affecting air quality in Cuba. Samples were obtained from pollution monitoring stations throughout Cuba. Different chemical analyses including elements and ions were conducted. Meteorological data was also included for the analysis. Results show that the pH was slightly basic for most stations, except those of the eastern region which exhibit pH values below 5.6. The major anthropogenic sources of ions are the burning of fossil fuel by power plants, cement factories, and nickel-processing industries and the burning of biomass through poor agricultural practices. The western region exhibited increased concentrations of NO3- and SO42- during the dry season, most likely due to the long-range transport of pollutants from the northeastern United States as well as local pollutants. Marine aerosols clearly influence Cuba’s rain. Only a small fraction of the potentially acidic ions contributes to the free acidity of Cuba’s rainwater, mainly due to the neutralizing capacity of some ions such as Cl-, Na+, Ca+2, and NH4+. The implementation of abatement techniques for SO2 and NOX and some elements emissions from major stationary sources will be an effective measure to improve air quality in Cuba.

Tropical land-cover change alters biogeochemical inputs to ecosystems in a Mexican montane landscape

In tropical regions, the effects of land-cover change on nutrient and pollutant inputs to ecosystems remain poorly documented and may be pronounced, especially in montane areas exposed to elevated atmospheric deposition. We examined atmospheric deposition and canopy interactions of sulfate-sulfur (SO4(2-)-S), chloride (Cl-), and nitrate-nitrogen (NO(3-)-N) in three extensive tropical montane land-cover types: clearings, forest, and coffee agroforest. Bulk and fog deposition to clearings was measured as well as throughfall (water that falls through plant canopies) ion fluxes in seven forest and five coffee sites. Sampling was conducted from 2005 to 2008 across two regions in the Sierra Madre Oriental, Veracruz, Mexico. Annual throughfall fluxes to forest and coffee sites ranged over 6-27 kg SO4(2-)-S/ha, 12-69 kg Cl-/ha, and 2-6 kg NO(3-)-N/ha. Sulfate-S in forest and coffee throughfall was higher or similar to bulk S deposition measured in clearings. Throughfall Cl- inputs, however, were consistently higher than Cl- amounts deposited to cleared areas, with net Cl- fluxes enhanced in evergreen coffee relative to semi-deciduous forest plots. Compared to bulk nitrate-N deposition, forest and coffee canopies retained 1-4 kg NO(3-)-N/ha annually, reducing NO(3-)-N inputs to soils. Overall, throughfall fluxes were similar to values reported for Neotropical sites influenced by anthropogenic emissions, while bulk S and N deposition were nine- and eightfold greater, respectively, than background wet deposition rates for remote tropical areas. Our results demonstrate that land-cover type significantly alters the magnitude and spatial distribution of atmospheric inputs to tropical ecosystems, primarily through canopy-induced changes in fog and dry deposition. However, we found that land cover interacts with topography and climate in significant ways to produce spatially heterogeneous patterns of anion fluxes, and that these factors can converge to create deposition hotspots. For land managers, this finding suggests that there is potential to identify species and ecosystems at risk of excess and increasing deposition in montane watersheds undergoing rapid transformation. Our data further indicate that montane ecosystems are vulnerable to air pollution impacts in this and similar tropical regions downwind of urban, industrial, and agricultural emission sources.

Analytical diagnosis methodology to evaluate nitrate impact on historical building materials

Nitrate salts have become of greater importance in the decay of materials from historical buildings due to changes in the environment. This work presents an analytical diagnosis methodology to evaluate the impact of nitrate salts in mortars and bricks, combining noninvasive and microdestructive analytical techniques together with chemometric and thermodynamic data analyses. The impact of nitrate salts cannot be well ascertained if other soluble salts are not taken into account. Therefore, the principal results from this work relate to nitrate salts but some results for other kinds of salts are included. Data from Raman microprobe spectroscopy and micro X-ray fluorescence (micro-XRF) are used to characterise the original composition and a first approximation of the nature of the decay compounds, mainly nitrates. The soluble salts are extracted and the anions and cations are quantified by means of ion chromatography with conductimetric detection for anions/cations and inductively coupled plasma mass spectrometry (ICP/MS) for cations. The values obtained allow two different data treatments to be applied. First, chemometric analysis is carried out to search for correlations among anions and cations. Second, thermodynamic modelling with the RUNSALT program is performed to search for environmental conditions of soluble salt formation. All the results are finally used to diagnose the impact of nitrates.