Biochar composite membrane for high performance pollutant management: Fabrication, structural characteristics and synergistic mechanisms

Fabrication of crown ether-containing copolymer porous membrane and their enhanced adsorption performance for cationic dyes: Experimental and DFT investigations

Adsorptive separation membranes are widely utilized for the removal of toxic dyeing pollutants from dyeing wastewater. However, developing novel adsorption membranes with large adsorption capacities and enhanced adsorption performance for dyes in actual wastewater poses a significant challenge. This study focuses on the fabrication of crown ether-containing copolymer porous membrane (CRPM) and investigation of the adsorption performance of dyes from aqueous solutions. The morphology structure and pore size distribution revealed that the membrane was endowed with rich micropores and hierarchical porous structures. Three typical cationic dyes (MB, RhB, CV) and an anionic dye (MO) were selected to evaluate the adsorption behavior. The results of adsorption isotherms and kinetics demonstrated that the adsorption data could be well-fitted using the Freundlich and pseudo-first-order kinetic models, the thermodynamic parameters revealed that the adsorption process of dyes on CRPM is a spontaneous endothermic reaction. The membrane exhibited excellent adsorption performance for cationic dyes, with RhB displaying a higher maximum adsorption capacity than previously reported porous membranes. Notably, dynamic adsorption-desorption filtration demonstrated a rapid removal efficiency, with RhB, MB, and CV achieving removal rates of 99.09%, 98.63%, and 99.14% respectively, after five cycles. The filtration volume of the CRPM membrane was 2.4-fold greater than that of a traditional PVDF membrane when applied to actual dyeing wastewater. DFT theoretical calculations were employed to elucidate the adsorption mechanism. These calculations confirmed the significant roles of electrostatic interactions, H-bonds and π-π interactions in facilitating the high-efficiency adsorption of cationic dyes. These findings highlight the potential of the crown ether-containing copolymer as a promising material for adsorption separation membranes in the treatment of dyeing wastewater.

Zwitterionic Tröger's Base Microfiltration Membrane Prepared via Vapor-Induced Phase Separation with Improved Demulsification and Antifouling Performance

The fouling of separation membranes has consistently been a primary factor contributing to the decline in membrane performance. Enhancing the surface hydrophilicity of the membrane proves to be an effective strategy in mitigating membrane fouling in water treatment processes. Zwitterionic polymers (containing an equimolar number of homogeneously distributed anionic and cationic groups on the polymer chains) have been used extensively as one of the best antifouling materials for surface modification. The conventional application of zwitterionic compounds as surface modifiers is intricate and inefficient, adding complexity and length to the membrane preparation process, particularly on an industrial scale. To overcome these limitations, zwitterionic polymer, directly used as a main material, is an effective method. In this work, a novel zwitterionic polymer (TB)-zwitterionic Tröger's base (ZTB)-was synthesized by quaternizing Tröger's base (TB) with 1,3-propane sultone. The obtained ZTB is blended with TB to fabricate microfiltration (MF) membranes via the vapor-induced phase separation (VIPS) process, offering a strategic solution for separating emulsified oily wastewater. Atomic force microscopy (AFM), scanning electron microscopy (SEM), water contact angle, and zeta potential measurements were employed to characterize the surface of ZTB/TB blended membranes, assessing surface morphology, charge, and hydrophilic/hydrophobic properties. The impact of varying ZTB levels on membrane surface morphology, hydrophilicity, water flux, and rejection were investigated. The results showed that an increase in ZTB content improved hydrophilicity and surface roughness, consequently enhancing water permeability. Due to the attraction of water vapor, the enrichment of zwitterionic segments was enriched, and a stable hydration layer was formed on the membrane surface. The hydration layer formed by zwitterions endowed the membrane with good antifouling properties. The proposed mechanism elucidates the membrane's proficiency in demulsification and the reduction in irreversible fouling through the synergistic regulation of surface charge and hydrophilicity, facilitated by electrostatic repulsion and the formation of a hydration layer. The ZTB/TB blended membranes demonstrated superior efficiency in oil-water separation, achieving a maximum flux of 1897.63 LMH bar-1 and an oil rejection rate as high as 99% in the oil-water emulsion separation process. This study reveals the migration behavior of the zwitterionic polymer in the membrane during the VIPS process. It enhances our comprehension of the antifouling mechanism of zwitterionic membranes and provides guidance for designing novel materials for antifouling membranes.

Insights into current bio-processes and future perspectives of carbon-neutral treatment of industrial organic wastewater: A critical review

With the rise of the concept of carbon neutrality, the current wastewater treatment process of industrial organic wastewater is moving towards the goal of energy conservation and carbon emission reduction. The advantages of anaerobic digestion (AD) processes in industrial organic wastewater treatment for bio-energy recovery, which is in line with the concept of carbon neutrality. This study summarized the significance and advantages of the state-of-the-art AD processes were reviewed in detail. The application of expanded granular sludge bed (EGSB) reactors and anaerobic membrane bioreactor (AnMBR) were particularly introduced for the effective treatment of industrial organic wastewater treatment due to its remarkable prospect of engineering application for the high-strength wastewater. This study also looks forward to the optimization of the AD processes through the enhancement strategies of micro-aeration pretreatment, acidic-alkaline pretreatment, co-digestion, and biochar addition to improve the stability of the AD system and energy recovery from of industrial organic wastewater. The integration of anaerobic ammonia oxidation (Anammox) with the AD processes for the post-treatment of nitrogenous pollutants for the industrial organic wastewater is also introduced as a feasible carbon-neutral process. The combination of AnMBR and Anammox is highly recommended as a promising carbon-neutral process for the removal of both organic and inorganic pollutants from the industrial organic wastewater for future perspective. It is also suggested that the AD processes combined with biological hydrogen production, microalgae culture, bioelectrochemical technology and other bio-processes are suitable for the low-carbon treatment of industrial organic wastewater with the concept of carbon neutrality in future.

Anti-fouling PVDF membranes incorporating photocatalytic biochar-TiO2 composite for lignin recycle

In this study, a photocatalytic biochar-TiO₂ (C-Ti) composite was prepared using lignin as carbon precursor, and blended with PVDF polymer to fabricate PVDF/C-Ti MMMs via non-solvent induced phase inversion. The prepared membrane demonstrates both 1.5 times higher initial and recovered fluxes than the similarly prepared PVDF/TiO₂ membrane, suggesting the C-Ti composite can help maintain higher photodegradation efficiency and better anti-fouling performance. In addition, the comparison of PVDF/C-Ti membrane against pristine PVDF membrane show that the reversible fouling and photodegradation reversible fouling of BSA increased from 10.1% to 6.4%-35.1% and 26.6%, respectively. And the FRR of PVDF/C-Ti membrane was 62.12%, 1.8 times that of PVDF membrane. The PVDF/C-Ti membrane was also applied for lignin separation, where the rejection to sodium lignin sulfonate was maintained at about 75%, and the flux recovery ratio after UV irradiation reached 90%. The demonstrated the advantages of PVDF/C-Ti membrane in photocatalytic degradation and antifouling performance.

Applications of biochar in sulfate radical-based advanced oxidation processes for the removal of pharmaceuticals and personal care products

Recently, biochar (BC) has been increasingly used as a catalyst for the degradation of 'emerging pollutants' (EPs). Pharmaceuticals and personal care products (PPCPs), which come under 'EPs', can be harmful to the aquatic ecosystem despite being present in very low concentrations (ng/L-μg/L). Advanced oxidation processes (AOPs), which produce sulfate radical (SR-AOPs), show a great potential to degrade PPCPs effectively from wastewater. It is mainly due to the higher stability, long half-lives and better non-selectivity of SO₄^{• -} compared with AOPs with •OH generation. Furthermore, research focus is now given on AOPs coupled with BC-supported catalyst to enhance the degradation of PPCPs because of quicker generation of radicals (•OH, SO₄^•-) by the activation of persulfate (PS) and peroxymonosulfate (PMS). This article sheds light on the catalytic ability of BC after its physical and chemical modifications such as acid/alkali treatment and metal doping. The role of persistent free radicals (PFRs) in the BC for effective removal of PPCPs has been elaborated. Its potential applications in synthetic as well as real wastewater have also been discussed.

Natural and recycled materials for sustainable membrane modification: Recent trends and prospects

Despite water being critical for human survival, its uneven distribution, and exposure to countless sources of pollution make water shortages increasingly urgent. Membrane technology offers an efficient solution for alleviating the water shortage impact. The selectivity and permeability of membranes can be improved by incorporating additives of different nature and size scales. However, with the vast debate about the environmental and economic feasibility of the common nanoscale materials in water treatment applications, we can infer that there is a long way before the first industrial nanocomposite membrane is commercialized. This stumbling block has motivated the scientific community to search for alternative modification routes and/or materials with sustainable features. Herein, we present a pragmatic review merging the concept of sustainability, nanotechnology, and membrane technology through the application of natural additives (e.g., Clays, Arabic Gum, zeolite, lignin, Aquaporin), recycled additives (e.g., Biochar, fly ash), and recycled waste (e.g., Polyethylene Terephthalate, recycled polystyrene) for polymeric membrane synthesis and modification. Imparted features on polymeric membranes, induced by the presence of sustainable natural and waste-based materials, are scrutinized. In addition, the strategies harnessed to eliminate the hurdles associated with the application of these nano and micro size additives for composite membranes modification are elaborated. The expanding research efforts devoted recently to membrane sustainability and the prospects for these materials are discussed. The findings of the investigations reported in this work indicate that the application of natural and waste-based additives for composite membrane fabrication/modification is a nascent research area that deserves the attention of both research and industry.

Biochar-based asymmetric membrane for selective removal and oxidation of hydrophobic organic pollutants

Hydrophobic organic pollutants (HOCs) in the complex groundwater and soil pose serious technical challenges for sustainable remediation. Herein, an asymmetric membrane (PCAM), inspired by the plant cuticle, was comprised of a top polydimethylsiloxane layer being selectively penetrable to HOCs from complex solution with humic acid, followed by transfer and catalyst layers with biochar pyrolyzed by 300 °C (BC300) and 700 °C (BC700). The PCAM triggered the advanced oxidation of the coming pollutant. The graphitized biochar layer of the PCAM acted as catalysts that induced HOC removal through a non-radical oxidation pathway. Compared to one type biochar membrane, the sequential multi-biochar composite membrane had a faster removal efficiency. The greater uptake and transport performance of multi-biochar composite membrane could be due to the larger pore size and distribution properties of PCAM physicochemical properties and oxidative degradation of peroxymonosulfate. The developed PCAM technology benefits from selective adsorption and catalytic oxidation and has the potential to be applied in complex environmental restoration.

Green Hydrogel-Biochar Composite for Enhanced Adsorption of Uranium

Uranium is the backbone of the nuclear fuel used for energy production but is still a hazardous environmental contaminant; thus, its removal and recovery are important for energy security and environmental protection. So far, the development of biocompatible, efficient, economical, and reusable adsorbents for uranium is still a challenge. In this work, a new orange peel biochar-based hydrogel composite was prepared by graft polymerization using guar gum and acrylamide. The composite's structural, morphological, and thermal characteristics were investigated via Fourier transform infrared (FTIR), scanning electron microscope (SEM), X-ray diffraction (XRD), and thermogravimetric analysis (TGA) methods. The composite's water absorption properties were investigated in different media. The performance of the prepared composite in adsorbing uranium (VI) ions from aqueous media was systematically investigated under varying conditions including solution's acidity and temperature, composite dose, contact time, and starting amount of uranium. The adsorption efficiency increased with solution pH from 2 to 5.5 and composite dose from 15 to 50 mg. The adsorption kinetics, isotherms, and thermodynamics parameters were analyzed to get insights into the process's feasibility and viability. The equilibrium data were better described through a pseudo-second-order mechanism and a Langmuir isotherm model, indicating a homogeneous composite surface with the maximum uranium (VI) adsorption capacity of 263.2 mg/g. The calculated thermodynamic parameters suggested that a spontaneous and endothermic process prevailed. Interference studies showed high selectivity toward uranium (VI) against other competing cations. Desorption and recyclability studies indicated the good recycling performance of the prepared composite. The adsorption mechanism was discussed in view of the kinetics and thermodynamics data. Based on the results, the prepared hydrogel composite can be applied as a promising, cost-effective, eco-friendly, and efficient material for uranium (VI) decontamination.

Efficient adsorptive removal of short-chain perfluoroalkyl acids using reed straw-derived biochar (RESCA)

Drinking water and groundwater treatment of perfluoroalkyl acids (PFAAs) heavily relies on adsorption-based approaches using carbonaceous materials, such as granular activated carbon (GAC). Application of GAC is restricted by its inefficiency to remove short-chain PFAAs that have prevalently emerged as substitutes and/or metabolites of long-chain polyfluoroalkyl and perfluoroalkyl substances (PFAS). Here, we synthesized reed straw-derived biochar (RESCA) exhibiting exceptional removal efficiencies (>92%) toward short-chain PFAAs at environment-relevant concentrations (e.g., 1 μg/L). Pseudo-second-order kinetic constants of RESCA were 1.13 and 1.23 L/(mg h) for perfluorobutanoic acid (PFBA) and perfluorobutanesulfonic acid (PFBS), respectively, over six times greater than GAC. SEM imaging and BET analysis revealed the combination of highly hydrophobic surface and scattered distribution of mesopores (2-10 nm in diameter) was associated with the rapid adsorption of short-chain PFAAs. RESCA-packed filters demonstrated effective removal of the mixture of three short-chain and three long-chain PFAAs in the influent with the flow rate up to 45 mL/min. In contrast, GAC-packed filters were significantly less efficient in the removal of short-chain PFAAs, which were also negatively affected by the increase of the flow rate. Efficacy of RESCA-packed filters was also validated in four PFAA-spiked groundwater samples from different sites. Dissolved organic matter (DOC) of >8 mg/L can negatively affect the removal of short-chain PFAAs by RESCA. Feasibility of scaling up the RESCA adsorption system was investigated using breakthrough simulation. Overall, RESCA represents a green adsorbent alternative for the feasible and scalable treatment of a wide spectrum of PFAAs of different chain lengths and functional moieties.

Review of organic and inorganic pollutants removal by biochar and biochar-based composites

Biochar (BC) has exhibited a great potential to remove water contaminants due to its wide availability of raw materials, high surface area, developed pore structure, and low cost. However, the application of BC for water remediation has many limitations. Driven by the intense desire of overcoming unfavorable factors, a growing number of researchers have carried out to produce BC-based composite materials, which not only improved the physicochemical properties of BC, but also obtained a new composite material which combined the advantages of BC and other materials. This article reviewed previous researches on BC and BC-based composite materials, and discussed in terms of the preparation methods, the physicochemical properties, the performance of contaminant removal, and underlying adsorption mechanisms. Then the recent research progress in the removal of inorganic and organic contaminants by BC and BC-based materials was also systematically reviewed. Although BC-based composite materials have shown high performance in inorganic or organic pollutants removal, the potential risks (such as stability and biological toxicity) still need to be noticed and further study. At the end of this review, future prospects for the synthesis and application of BC and BC-based materials were proposed. This review will help the new researchers systematically understand the research progress of BC and BC-based composite materials in environmental remediation.

Biological performance and fouling mitigation in the biochar-amended anaerobic membrane bioreactor (AnMBR) treating pharmaceutical wastewater

Anaerobic membrane bioreactor (AnMBR) is an advanced technology in treating pharmaceutical wastewater, but the membrane fouling limits its development. In this study, the biochar with adsorption capacity of biopolymers was added in AnMBR to investigate its potential in treating pharmaceutical wastewater and alleviating membrane fouling. In the biochar-amended AnMBR, adsorbable organic halogen (AOX) was removed effectively, and more COD was biotransformed into CH₄. Membrane fouling mitigation was achieved in the third stage with a 56% decrease of average transmembrane pressure difference (TMP) rising rate. The predominant culprit, proteins of extracellular polymeric substance (EPS-proteins) in sludge mixture and cake layer, was reduced significantly. Particularly, the proportion of micromolecular (0.1-0.15 kDa) EPS-proteins in cake layer was 1.5-folds that of the control group. The important bio-foulant genus Arcobacter aggregating on the membrane had less and almost half the relative abundance (16.5%) than that of the control group (30.7%).

Recent advances in mitigating membrane biofouling using carbon-based materials

Biofouling is the Achilles Heel of membrane processes. The accumulation of organic foulants and growth of microorganisms on the membrane surface reduce the permeability, shorten the membrane life, and increase the energy consumption. Advancements in novel carbon-based materials (CBMs) present significant opportunities in mitigating biofouling of membrane processes. This article provides a comprehensive review of the recent progress in the application of CBMs in antibiofouling membrane. It starts with a detailed summary of the different antibiofouling mechanisms of CBM-containing membrane systems. Next, developments in membrane modification using CBMs, especially carbon nanotubes and graphene family materials, are critically reviewed. Further, the antibiofouling potential of next-generation carbon-based membranes is surveyed. Finally, the current problems and future opportunities of applying CBMs for antibiofouling membranes are discussed.

Porous PVdF/GO Nanofibrous Membranes for Selective Separation and Recycling of Charged Organic Dyes from Water

Graphene oxide (GO) membranes are robust and continue to attract great attention due to their fascinating properties, despite their potential issues regarding stability and selectivity in aqueous-phase processing. That being said, however, the functional moieties of GO could be used for membrane surface modification, while ensuring simultaneous removal and recycling of industrial organic dyes. Herein, we present a versatile porous structured polyvinylidene fluoride-graphene oxide (PVdF-GO) nanofibrous membranes (NFMs), prepared by using simple and straightforward electrospinning approach for selective separation and filtration. The GO nanosheets were distributed homogeneously throughout the PVdF nanofiber, regulating the surface morphology and performance of PVdF-GO NFM. The PVdF-GO NFMs possesses high mechanical strength and surface free energy (SFE), consequently resulting high permeation and filtration efficiency as compared to PVdF NFM. The selectivity (99%) toward positively charged dyes based on electrostatic attraction, while maintaining rejection (100%) for negatively charged dye from mixed solutions highlight the role of GO in PVdF-GO NFM, owing to uniform pores and negatively charged surface. In addition, the actual efficiency of NFMs could be recovered easily up to three consecutive filtration cycles by regeneration, thereby assuring high stability. The high permeation, purification and filtration efficiency, good stability and recycling of PVdF-GO NFMs are promising for use in practical water purification and applications, particularly for selective filtration and recycling of dyes.

Kinetic and isothermal adsorption-desorption of PAEs on biochars: effect of biomass feedstock, pyrolysis temperature, and mechanism implication of desorption hysteresis

Biochar has the potential to sequester biomass carbon efficiently into land, simultaneously while improving soil fertility and crop production. Biochar has also attracted attention as a potential sorbent for good performance on adsorption and immobilization of many organic pollutants such as phthalic acid esters (PAEs), a typical plasticizer in plastic and presenting a current environmental issue. Due to lack of investigation on the kinetic and thermodynamic adsorption-desorption of PAEs on biochar, we systematically assessed adsorption-desorption for two typical PAEs, dimethyl phthalate (DMP) and diethyl phthalate (DEP), using biochar derived from peanut hull and wheat straw at different pyrolysis temperatures (450, 550, and 650 °C). The aromaticity and specific surface area of biochars increased with the pyrolysis temperature, whereas the total amount of surface functional groups decreased. The quasi-second-order kinetic model could better describe the adsorption of DMP/DEP, and the adsorption capacity of wheat straw biochars was higher than that of peanut hull biochars, owing to the O-bearing functional groups of organic matter on exposed minerals within the biochars. The thermodynamic analysis showed that DMP/DEP adsorption on biochar is physically spontaneous and endothermic. The isothermal desorption and thermodynamic index of irreversibility indicated that DMP/DEP is stably adsorbed. Sorption of PAEs on biochar and the mechanism of desorption hysteresis provide insights relevant not only to the mitigation of plasticizer mobility but also to inform on the effect of biochar amendment on geochemical behavior of organic pollutants in the water and soil.