Evaluation of membrane tailored with biocompatible halloysite‒polyaniline nanomaterial for efficient removal of carcinogenic disinfection by‒products precursor from water

Bi2WO6 nanoparticles anchored on membrane by grafting via in-situ polymerization for the treatment of antibiotic and pesticides wastewater

Antibiotics, natural organic matter, and pesticides are detected in the ecosystem's domestic water, surface water, and groundwater and are largely applied in pharmaceuticals and agriculture. Polymeric membranes are effectively remove the various pollutants in the water bodies, but fouling is one of the major limitations of commercial membranes. Herein, we modified the polymeric membrane surface with inorganic photocatalytic nanoparticles. In this work, the hydrothermal method is used for the synthesis of Bi2WO6 nanoparticles and as-synthesized nanoparticles grafted onto the various polymeric membranes, including polyetherimide (PEI), cellulose acetate (CA), polyvinylidene fluoride (PVDF), and polysulfone (PSF). The functional group studies confirmed the existence of nanoparticles and hydroxyl groups on the hybrid membrane. Further, finger-like voids, top-surface morphology, and roughness on the membrane surface were validated via Field Emission Scanning Electron Microscopy (FESEM) and Atomic force microscopy (AFM), respectively. The significant rejection of tetracycline, humic acid, and fulvic acid + atrazine was noted with the synthesized membranes in the following order: PVDF (81.1%, 78.8%, 80.6%) > CA (70.1%, 69.3%, 71.7%) > PSF (72.5%, 73.6%, 67.1%) > PEI (75.9%, 65.5%, 63.7%). The photodegradation efficiency of hybrid membranes against tetracycline, humic acid, and fulvic acid + atrazine was observed in the order: PEI (28.5%, 25.8%, 30.2%) < CA (46.5%, 42.4%, 40.5%) < PSF (46.9%, 37.7%, 44.7%) < PVDF (67.7%, 62.1%, 64.3%). These membranes exhibit an outstanding permeate flux recovery ratio to the neat membrane. Therefore, the grafting of Bi2WO6 nanoparticles creates a potential bonding with PVDF membranes than other polymeric membranes, thus exhibiting an outstanding rejection than hybrid and neat membranes.

Recent Advances on the Fabrication of Antifouling Phase-Inversion Membranes by Physical Blending Modification Method

Membrane technology is an essential tool for water treatment and biomedical applications. Despite their extensive use in these fields, polymeric-based membranes still face several challenges, including instability, low mechanical strength, and propensity to fouling. The latter point has attracted the attention of numerous teams worldwide developing antifouling materials for membranes and interfaces. A convenient method to prepare antifouling membranes is via physical blending (or simply blending), which is a one-step method that consists of mixing the main matrix polymer and the antifouling material prior to casting and film formation by a phase inversion process. This review focuses on the recent development (past 10 years) of antifouling membranes via this method and uses different phase-inversion processes including liquid-induced phase separation, vapor induced phase separation, and thermally induced phase separation. Antifouling materials used in these recent studies including polymers, metals, ceramics, and carbon-based and porous nanomaterials are also surveyed. Furthermore, the assessment of antifouling properties and performances are extensively summarized. Finally, we conclude this review with a list of technical and scientific challenges that still need to be overcome to improve the functional properties and widen the range of applications of antifouling membranes prepared by blending modification.

Electrochemical quantification of atrazine-fulvic acid and removal through bismuth tungstate photocatalytic hybrid membranes

Herbicides such as atrazine and humus substances such as fulvic acid are widely used in agricultural sector. They can be traced in surface and groundwater around the agriculture field at concentrations beyond the approved limit due to their mobility and persistence. Bismuth-based photocatalysts activated by visible light are potential materials for removing various organic pollutants from water bodies. These photocatalysts can also be suitable candidates for developing a hybrid membrane with anti-fouling properties. In this study, Bi2WO6 nanoparticles were synthesized via the hydrothermal method and integrated into the cellulose acetate (CA), polyetherimide (PEI), polysulfone (PSF) and polyvinylidene fluoride (PVDF) polymers via physical blending approach. The hybrid membranes were then characterized by FTIR, XPS and FESEM to confirm the chemical bonding, chemical composition and surface morphology of Bi2WO6. Thus, the pure water flux of CA (35.6 L m-2 h-1), PEI (46.56 L m-2 h-1), PSF (6.84 L m-2 h-1), and PVDF (68.47 L m-2 h-1) hybrid membranes has significantly enhanced than the pristine CA, PEI, PSF and PVDF membranes. The significant rejection of atrazine-fulvic acid was observed with hybrid membranes in the order of CA (84.1%) > PVDF (72.7%) > PEI (47.8%) > PSF (37.2%), and these membranes have shown an excellent flux recovery ratio than pristine membranes. Further, electrochemical quantification studies were performed to analyze the removal efficiency of atrazine-fulvic acid from water. In this present work, GO-modified SPE was employed for electrochemical sensing studies. The resultant CA hybrid membrane achieved removal efficiency of 84.08% for atrazine. It was observed that the Bi2WO6 established strong bonding with CA, and PVDF membranes, thus showing a significant removal efficiency and FRR than other hybrid and pristine membranes.

Removal of protein, histological dye and tetracycline from simulated bioindustrial wastewater with a dual pore size PPSU membrane

Wastewater from production of active pharmaceutical ingredients (APIs) often contains proteins, azo dyes or antibiotics, which cause severe water eutrophication and growth of drug-resistant bacteria. A series of polyphenylsulfone (PPSU) membranes was prepared to determine the relationships between pore structures and the abilities of different membranes to separate foulants, and the characteristics and performance of the ultrafiltration membranes were investigated. The structure of the skin layer and the cross-sectional texture were converted from dense and finger-like macrovoids to porous sponge shapes because of a delayed liquid-liquid (L-L) demixing time. Formation of novel PPSU membranes via noncovalent bonding interactions was evaluated, and this selectively affected the membrane surface pore structure, layer thickness, surface polarity and electronic repulsive force. All PPSU membranes demonstrated excellent rejection of organic foulants, including bovine serum albumin (BSA) (~100% rejection) and acid red 1 (AR1) (~90% rejection). Additionally, M5 provided an excellent tetracycline (TC) rejection efficiency of 89% in the 1^st cycle. Due to the small size of TC, pore size effects were displayed. Moreover, the pure water flux recovery rate (FRR) increased from 85% (M1, water/ethanol: 100/0) to 99.9% (M4, water/ethanol: 30/70) after BSA filtration because the weak nonsolvent decreased the roughness of the membrane surface, and the membrane made with added EtOH yielded excellent FRR values (99.9%) after AR1 filtration. Therefore, PPSU membranes successfully achieved over 90% rejection of organic foulants and excellent FRRs, indicating that they may be suitable for purifying wastewater from API plants that generate organic foulants with a wide range of sizes.