Influence of functionalized exfoliated reduced graphene oxide nanoparticle localization on mechanical, thermal and electronic properties of nanobiocomposites

Biomimetic Growth of Hydroxyapatite in Hybrid Polycaprolactone/Graphene Oxide Ultra-Porous Scaffolds

This paper reports the preparation and characterization of hybrid scaffolds composed of polycaprolactone (PCL) and different graphene oxide (GO) amounts, intending to incorporate the intrinsic characteristics of their constituents, such as bioactivity and biocidal effect. These materials were fabricated by a solvent-casting/particulate leaching technique showing a bimodal porosity (macro and micro) that was around 90%. The highly interconnected scaffolds were immersed in a simulated body fluid, promoting the growth of a hydroxyapatite (HAp) layer, making them ideal candidates for bone tissue engineering. The growth kinetics of the HAp layer was influenced by the GO content, a remarkable result. Furthermore, as expected, the addition of GO neither significantly improves nor reduces the compressive modulus of PCL scaffolds. The thermal behavior of composites was investigated by differential scanning calorimetry, showing an increase in crystallinity as the addition of GO raised, which implies that GO nanosheets can act as seeds to induce the crystallization of PCL. The improved bioactivity was demonstrated by the deposition of an HAp layer on the surface of the scaffold with GO, especially with a 0.1% GO content.

Influence of Polymer Processing on the Double Electrical Percolation Threshold in PLA/PCL/GNP Nanocomposites

For the first time, the double electrical percolation threshold was obtained in polylactide (PLA)/polycaprolactone (PCL)/graphene nanoplatelet (GNP) composite systems, prepared by compression moulding and fused filament fabrication (FFF). Using scanning electron microscopy (SEM) and atomic force microscopy (AFM), the localisation of the GNP, as well as the morphology of PLA and PCL phases, were evaluated and correlated with the electrical conductivity results estimated by the four-point probe method electrical measurements. The solvent extraction method was used to confirm and quantify the co-continuity in these samples. At 10 wt.% of the GNP, compression-moulded samples possessed a wide co-continuity range, varying from PLA55/PCL45 to PLA70/PCL30. The best electrical conductivity results were found for compression-moulded and 3D-printed PLA65/PCL35/GNP that have the fully co-continuous structure, based on the experimental and theoretical findings. This composite owns the highest storage modulus and complex viscosity at low angular frequency range, according to the melt shear rheology. Moreover, it exhibited the highest char formation and polymers degrees of crystallinity after the thermal investigation by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC), respectively. The effect of the GNP content, compression moulding time, and multiple twin-screw extrusion blending steps on the co-continuity were also evaluated. The results showed that increasing the GNP content decreased the continuity of the polymer phases. Therefore, this work concluded that polymer processing methods impact the electrical percolation threshold and that the 3D printing of polymer composites entails higher electrical resistance as compared to compression moulding.

Interface Strengthening of PS/aPA Polymer Blend Nanocomposites via In Situ Compatibilization: Enhancement of Electrical and Rheological Properties

The process of strengthening interfaces in polymer blend nanocomposites (PBNs) has been studied extensively, however a corresponding significant enhancement in the electrical and rheological properties is not always achieved. In this work, we exploit the chemical reaction between polystyrene maleic anhydride and the amine group in nylon (polyamide) to achieve an in-situ compatibilization during melt processing. Herein, nanocomposites were made by systematically adding polystyrene maleic anhydride (PSMA) at different compositions (1-10 vol%) in a two-step mixing sequence to a Polystyrene (PS)/Polyamide (aPA) blend with constant composition ratio of 25:75 (PS + PSMA:aPA) and 1.5 vol% carbon nanotube (CNT) loading. The order of addition of the individual components was varied in two-step mixing procedure to investigate the effect of mixing order on morphology and consequently, on the final properties. The electrical and rheological properties of these multiphase nanocomposite materials were investigated. The optical microscope images show that for PS/aPA systems, CNTs preferred the matrix phase aPA, which is the thermodynamically favorable phase according to the wettability parameter calculated using Young's equation. However, aPA's great affinity for CNT adversely influenced the electrical properties of our blend. Adding PSMA to PS/aPA changed the structure of the droplet phase significantly. At 1.5 vol% CNT, a more regular and even distribution of the droplet domains was observed, and this produced a better framework to create more CNT networks in the matrix, resulting in a higher conductivity. For example, with only 1.5 vol% CNT in the PBN, at 3 vol% PSMA, the conductivity was 7.4 × 10^-2 S/m, which was three and a half orders of magnitude higher than that seen for non-reactive PS/aPA/CNT PBN. The mechanism for the enhanced conductive network formation is delineated and the improved rheological properties due to the interfacial reaction is presented.

Fabrication of reinforced and toughened PC/PMMA composites by tuning the migration and selective location of graphenes during melt blending

In this work, we creatively obtained reinforced and toughened PC/PMMA/GNs composites by tuning the migration and selective location of graphene nanosheets (GNs) during melt blending. TEM results revealed that the migration of GNs in PC/PMMA blends during melt blending always existed no matter how the GNs were introduced, and most of them exclusively localized at the interface of PC and PMMA phase due to interfacial effects. The migration of GNs could refine the size of the dispersed phase, and the exclusive localization of GNs at the interface show obvious interfacial compatibilizing effects, leading to improved mechanical properties of the composites. It was found that the composite prepared by one-step compounding showed significant enhanced strength and toughness with addition of mere 0.05 wt% GNs and the tensile strength and elongation of the composite increased by about 62.96% and 94.54%, respectively as compared to the PC/PMMA blends. Moreover, the composite prepared by one-step compounding also showed improved thermal conductivity at the same time, indicating excellent comprehensive properties. It is believed that tuning the migration and selective localization of GNs open perspectives for the development of high-performance polymer composites.

By adjusting the dispersion and distribution of graphene nanosheets (GNs) filler in polycarbonate/polymethyl methacrylate (PC/PMMA) composites, only 0.05 wt% GNs filler can significantly improve the strength and toughness of the composites.

Facile and Low Environmental Impact Approach to Prepare Thermally Conductive Nanocomposites Based on Polylactide and Graphite Nanoplatelets

In this work, the preparation of nanocomposites based on poly(l-lactide) PLLA and graphite nanoplatelets (GNP) was assessed by applying, for the first time, the reactive extrusion (REX) polymerization approach, which is considered a low environmental impact method to prepare polymer systems and which allows an easy scalability. In particular, ad hoc synthesized molecules, constituted by a pyrene end group and a poly(d-lactide) (PDLA) chain (Pyr-d), capable of interacting with the surface of GNP layers as well as forming stereoblocks during the ring-opening polymerization (ROP) of l-lactide, were used. The nanocomposites were synthesized by adding to l-lactide the GNP/initiator system, prepared by dispersing the graphite in the acetone/Pyr-d solution, which was dried after the sonication process. DSC and X-ray diffraction measurements evidenced the stereocomplexation of the systems synthesized by using the pyrene-based initiators, whose extent turned out to depend on the PDLA chain length. All the prepared nanocomposites, including those synthesized starting from a classical initiator, that is, 1-dodecanol, retained similar electrical conductivity, whereas the thermal conductivity was found to increase in the stereocomplexed samples. Preferential localization of stereocomplexed PLA close to the interface with GNP was demonstrated by scanning probe microscopy (SPM) techniques, supporting an important role of local crystallinity in the thermal conductivity of the nanocomposites.