"Adsorptive removal of Congo Red dye from its aqueous solution by Ag-Cu-CeO2 nanocomposites: Adsorption kinetics, isotherms, and thermodynamics"

An investigation of the adsorption of Congo red dye on two naturally occurring adsorbents Hydroxyapatite and Bentonite: An Experimental Analysis, DFT calculations, and Monte Carlo simulation

Congo Red (CR) dye is classified as a toxic and carcinogenic substance, posing significant health and environmental risks. To address this issue, the adsorption efficiency of CR on natural bentonite and hydroxyapatite (HA) was systematically studied. The adsorbents were successfully characterized by XRD, FTIR, and SEM analysis. Optimization through the Box-Behnken method identified the optimal conditions (pH = 6.5, initial dye concentration = 150 mg/L, and adsorbent mass = 1.5 g/L), resulting in maximum removal of CR of 95 % for HA and 84 % for bentonite. 2.6.2. Monte Carlo (MC) simulations provided insights into the spontaneous and favorable adsorption behavior, particularly under acidic conditions, driven by van der Waals interactions. Kinetic studies revealed that the adsorption followed a pseudo-second-order model (R2 = 0.99). Furthermore, regeneration tests demonstrated that HA and bentonite retained 75 % and 60 % of their adsorption capacities, respectively, after five cycles, indicating their potential for sustainable reuse in dye removal. The exceptional adsorption efficiency and reusability of these natural adsorbents make them promising candidates for environmental remediation, contributing to a deeper understanding of the underlying adsorption mechanisms.

Preparation of new green poly (amino amide) based on cellulose nanoparticles for adsorption of Congo red and its adaptive neuro-fuzzy modeling

In this study, a novel green poly(amino amide) nanoparticle based on cellulose nanoparticles (Cell-PAMN) was developed for the efficient adsorption of Congo Red dye. Cellulose nanocrystals obtained from acid hydrolysis of cotton linter were functionalized via Oxa-Michael addition of acrylamide on their surface hydroxyl groups, followed by transamidation with ethylenediamine. The resulting nanoparticles were characterized using FT-IR spectroscopy, SEM, and X-ray diffraction techniques. The as-prepared Cell-PAMN exhibited considerably higher adsorption capacity compared to unmodified cellulose nanoparticles due to the presence of amino and amide functional groups. The adsorption kinetics and the effects of parameters such as contact time and initial dye concentration on the adsorption capacity were investigated. An adaptive Neuro-Fuzzy model was used to study the efficiency of dye removal, accurately predicted the adsorption behavior of Cell-PAMN. The kinetic study results showed that the adsorption process followed a pseudo-second-order kinetic model, with a maximum adsorption capacity of around 40 mg/g. The results demonstrated the potential of the synthesized material for the removal of Congo Red from aqueous solutions, highlighting its applicability in wastewater treatment. This research contributes to the development of sustainable and eco-friendly materials for environmental remediation applications.

Adsorption of Congo red on magnetic cobalt-manganese ferrite nanoparticles: Adsorption kinetic, isotherm, thermodynamics, and electrochemistry

Magnetic Co0.5Mn0.5Fe2O4 nanoparticles were successfully prepared via the combustion and calcination process, with an average particle diameter of 31.5 nm and a saturation magnetization of 25.25 emu·g-1, they were employed to adsorbe Congo red (CR) from wastewater, the Pseudo-second-order kinetic and Freundlich isotherm were consistent with the adsorption data, indicating that their adsorption was a multilayer chemisorption process, the thermodynamic investigation showed that the adsorption was a favored exothermic process. The ionic strength of Cl- in CR solution had no obvious effect on the adsorption efficiency of Co0.5Mn0.5Fe2O4 nanoparticles, and the maximum adsorbance was 58.3 mg·g-1 at pH 2, decreasing as the pH of the CR solutions increased from 2 to 12. The ion leaching experiment and XRD demonstrated that Co0.5Mn0.5Fe2O4 nanoparticles had excellent stability, and the relative removal rate was 93.85% of the first time after 7 cycles. Cyclic voltammetry and electrochemical impedance spectroscopy demonstrated that CR was adsorbed onto Co0.5Mn0.5Fe2O4 nanoparticles, and the electrical conductivity of Co0.5Mn0.5Fe2O4 nanoparticles decreased after adsorption of CR. Magnetic Co0.5Mn0.5Fe2O4 nanoparticles displayed a promising application in wastewater treatment.

Reactive Blue MEBF 222 dye and textile wastewater treatment using metal-doped cobalt and nickel perovskites by batch and column adsorption process

Water contamination is a serious issue that has an impact on the whole globe. In the current work, adsorption technique was used to remove synthetic Reactive Blue MEBF 222 textile dye utilizing Cd-doped Co (Co1 - xCd1.5xFeO3), Zn-doped Co (Co1 - xZn1.5xFeO3), Cr-doped Co (Co1 - xCr1.5xFeO3), Zn-doped Ni (Ni1 - xZn1.5xFeO3), and Cr-doped Ni (Ni1 - xCr1.5xFeO3) perovskites, synthesized by sol-gel auto-combustion approach. According to the findings of batch adsorption studies, maximum adsorption was observed at pH 3 (45.62 mg/g), 0.01 g/50 ml dosage (36.67 mg/g), 60 min (14.31 mg/g), 100 ppm dye concentration (47.41 mg/g), and 308 K (35.96 mg/g) for Co1 - xCd1.5xFeO3; at 3 pH (42.94 mg/g), 0.01 g/50 ml dosage (35.33 mg/g), 60 min (12.88 mg/g), 100 ppm dye concentration (40.52 mg/g), and 308 K (31.31 mg/g) for Co1 - xZn1.5xFeO3; at 2 pH (38.82 mg/g), 0.01 g/50 ml dosage (32.20 mg/g), 60 min (11.98 mg/g), 100 ppm dye concentration (33.54 mg/g), and 308 K (29.34 mg/g) for Co1 - xCr1.5xFeO3; at 2 pH (34.97 mg/g), 0.01 g/50 ml dosage (30.41 mg/g), 60 min (10.46 mg/g), 100 ppm dye concentration (27.19 mg/g), and 308 K (26.12 mg/g) for Ni1 - xZn1.5xFeO3; and at 2 pH (31.22 mg/g), 0.01 g/50 ml dosage (25.04 mg/g), 60 min (9.48 mg/g), 100 ppm dye concentration (21.73 mg/g), and 308 K (23.61 mg/g) for Ni1 - xCr1.5xFeO3. The pseudo-second-order model showed good fitness for adsorption kinetic data. Electrolytes, detergents/surfactants, and heavy metal ions had a substantial impact on the adsorption potential. The column adsorption experiments demonstrated optimal bed height, flow rate, and intake dye concentration to be 3 cm, 1.8 ml/min, and 70 mg/l, respectively, in the column experiment. With an adsorption capacity of 44.1 mg/g, reactive blue (RB) 222 dye was able to achieve its maximum adsorption. Detailed desorption of RB 222 dye was also achieved. The novelty of this adsorption method lies in its eco-friendliness, ease of handling, and cost-effectiveness.

Ni-Zn/CeO2 nanocomposites for enhanced adsorptive removal of 4-chlorophenol

Chlorophenols are one of the major organic pollutants responsible for the contamination of water bodies. This study explores the application of Ni-Zn/CeO2 nanocomposites, synthesized via the aqueous co-precipitation method, as effective adsorbents for the 4-chlorophenol removal from aqueous solutions. The nanocomposites' chemical and structural characteristics were assessed using different physical characterization methods, viz. X-ray diffraction, transmission electron microscopy, Fourier transform infrared spectroscopy, zeta potential, using a Box-Behnken design within response surface methodology, optimal conditions of pH 3, temperature 20 °C, contact time 120 min, adsorbent dosage 0.05 g, and 4-chlorophenol concentration 50 ppm are identified. Among the nanocomposites tested, NZC 20:10:70, with 20% Ni and 10% Zn, achieves enhanced performance, removing 99.1% of 4-chlorophenol within 2 h. Adsorption kinetics follow the pseudo-second-order model and equilibrium data fit the Freundlich isotherm. Thermodynamic analysis indicates an exothermic and spontaneous process. The adsorption capacity of NZC 20:10:70 shows significant enhancement, growing from 19.85 mg/g at 10 ppm to 96.33 mg/g at 50 ppm initial concentration. Physical characterization confirms NZC 20:10:70's superior properties, including a high surface area of 118.471 m2/g. Evaluating economic viability, NZC 20:10:70 demonstrates robust reusability, retaining 85% efficiency over eight regeneration cycles. These results highlight NZC 20:10:70 as a promising adsorbent for effective and sustainable chlorophenol removal in water treatment.

Enhancing photocatalytic tetracycline degradation through the fabrication of high surface area CeO2 from a cerium-organic framework

Water pollution is a global environmental issue, and the presence of pharmaceutical compounds, such as tetracyclines (TCs), in aquatic ecosystems has raised growing concerns due to the potential risks to both the environment and human health. A high surface area CeO2 was prepared via atmospheric thermal treatment of a metal-organic framework of cerium and benzene-1,3,5-tricarboxylate. The effects of calcination temperature on the morphology, structure, light absorption properties and tetracycline removal efficiency were studied. The best activity of the photocatalysts could be achieved when the heat treatment temperature is 300 °C, which enhances the photocatalytic degradation performance towards tetracycline under visible light. The resulting CeO2 particles have high capacity for adsorbing TCs from aqueous solution: 90 mg g-1 for 60 mg L-1 TCs. As a result, 98% of the initial TC can be removed under simulated sunlight irradiation. The cooperation of moderate defect concentration and disordered structure showed tetracycline removal activity about 10 times higher than the initial Ce-MOF. An embryotoxicity assessment on zebrafish revealed that treatment with CeO2 particles significantly decreased the toxicity of TC solutions.

Synthesis, characterization and application of steel waste-based iron oxide nanoparticles for removal of heavy metals from industrial wastewaters

Water treatment and reuse can avail more clean and safe water for human use. In this study, iron oxide waste powder generated from the steel pickling process was used to develop iron oxide nanoparticles (IONPs) using solution gelation synthesis process. The powder and developed IONPs were characterized by X-ray fluorescence and diffraction (XRF, XRD), scanning electron microscopy, Fourier-transform infrared spectroscopy, and Brunauer-Emmett-Teller (BET) analyses. Adsorption experiments were carried out on synthetic water with lead and chromium metal ions. The adsorption data were analysed with Langmuir and Freundlich models. Adsorption kinetics were also analysed with Pseudo-First-Order and Pseudo-Second-Order models using non-linear regression. The synthesized IONPs were porous with active surface functional groups of hydroxyl bonds, with BET specific surface area of 325.02 m2/g. XRD results confirmed the cubic spinel structure of IONPs with particle sizes of 20-30 nm. The nanoparticles at a dosage of 0.35 g in 10 mL for 50 min effectively removed Pb(II) and Cr(VI) metal ions up to 99.9% from both synthetic water and industrial wastewater. The adsorption capacity (qmax) of IONPs was found to be 417 and 326.80 for Pb(II) and Cr(VI) respectively. Freundlich isotherm model data fitted best for the removal of both metal ions. The regression values for kinetic models confirmed that pseudo-second-order best fit the adsorption of both Pb(II) and Cr(VI) confirming chemisorption processes. This study contributes to elucidating alternative application of pickling waste from the steel rolling mills for the benefit of heavy metal removal in industrial wastewater.

Expermental investigation on adsorption of methylene blue dye from waste water using corncob cellulose-based hydrogel

Hydrogel from corncob cellulose was synthesized in this investigation. The synthesized Hydrogel was characterized by SEM, XRD, and FTIR instruments. As the results indicate the synthesized hydrogel has required and important features, these suggest the suitability of hydrogel for the adsorption of methylene blue dye (MBD). Three important process variables (dosage, contact time, and initial concentration) with three levels were studied during the adsorption process at 30 °C and neutral pH. The efficiency of hydrogel for adsorption of MBD was determined in each experiment. The experimental results were statistically analyzed and interpreted. The maximum removal efficiency was achieved at 2.22 g/L of dosage, 80.36 min of contact time, and 74.54 mg/L of initial concentration. At this condition, 98.25% of MBD was achieved through experimental tests. Kinetics, isotherm, and thermodynamics studies were performed. Langmuir isotherm is more suitable to describe the adsorption process and the Pseudo second-order kinetic model fits this process. From the thermodynamics studies, all negative values of change in Gibbs free energy (ΔG°), and positive value of change in enthalpy (ΔH°), and change in entropy (ΔS°) indicate that the carried out experimental process is a spontaneous and endothermic. Moreover, the regeneration experiment for adsorbent was performed. The treatment of real textile industry waste water was conducted and the removal efficiency of hydrogel was 64.76%. This removal percentage reduction from sythetic aqueous solution is due to involvement of other pollutants in the real waste water. The synthesized hydrogel adsorbent is suitable up to the third cycle without significant loss in removal efficiency.

Design of chitosan/boehmite biocomposite for the removal of anionic and nonionic dyes from aqueous solutions: Adsorption isotherms, kinetics, and thermodynamics studies

This study introduces a chitosan/boehmite biocomposite as an efficient adsorbent for removing anionic Congo Red (CR) and non-ionic Bromothymol Blue (BTB) from water. Boehmite nanoparticles were synthesized using the Sol-gel method and then attached to chitosan particles using sodium tripolyphosphate through co-precipitation method. Characterized through FTIR, FE-SEM, BET, and XRD, the biosorbent displayed structural integrity with optimized pH conditions of 3 for CR and 4 for BTB, achieving over 90 % adsorption within 30 min. Pseudo second order kinetics model and Langmuir isotherm revealed monolayer sorption with capacities of 64.93 mg/g for CR and 90.90 mg/g for BTB. Thermodynamics indicated a spontaneous and exothermic process, with physisorption as the primary mechanism. The biosorbent demonstrated excellent performance and recyclability over five cycles, highlighting its potential for eco-friendly dye removal in contaminated waters.