Synthesis and property of superabsorbent polymer based on cellulose grafted 2-acrylamido-2-methyl-1-propanesulfonic acid

Production, structure, and performance of guar gum based bacterial cellulose generated from soy sauce residue hydrolysate by in-situ fermentation

Guar gum based bacterial cellulose (GG-BC) was generated from the soy sauce residue hydrolysate by in-situ fermentation, and its structure and performance were learned systematically. The GG concentration of 0.2 % was most suitable for GG-BC production with the yield of 1.21 g/L. During the in-situ fermentation, GG was implanted into the nano network of BC and thus altered its microstructure and properties. According to the FT-IR and NMR results, GG-BC had similar functional group structure and cellulose structural framework to those of BC. The degree of polymerization (DP) of GG-BC was 526.32-832.16, which was higher than that (426.32) of BC. Also, the GG-BC with low GG addition (0.2 % and 0.4 %) had a higher crystallinity than BC. Moreover, the GG-BC had a better heat tolerance than BC based on its higher temperature reaching the maximum degradation rate. The GG-BC with suitable GG addition had better texture characteristics, UV barrier property, swelling rate, and antioxidant activity than those of BC, showing that the in-situ fermentation with GG addition could promote the performance of GG-BC. Overall, this study can provide an attractive technology for both solving the environmental issue brought by soy sauce residue and producing high value-added GG-BC with good performance efficiently.

Synthesis and Characterization of a Superabsorbent Polymer Gel Using a Simultaneous Irradiation Technique on Corn Straw

Utilizing gamma rays as an initiating agent, a simultaneous irradiation method was applied to graft acrylic acid and acrylamide onto corn straw that had been decrystallized using a NaOH/urea solution at a reduced temperature, aiming to fabricate superabsorbent polymer gel (SAPG) capable of absorbing significantly more water. The structural attributes of the corn straw, the decrystallized corn straw, and the SAPG were analyzed via Fourier transform infrared spectroscopy (FTIR), X-ray crystal powder diffraction (XRD), thermogravimetric analysis (TG), and scanning electron microscopy (SEM). To enhance the SAPG's performance, optimization of various parameters was carried out, such as irradiation dose, dose rate, the ratio of monomer to corn straw, the proportion of acrylic acid (AA) to acrylamide (Am), and the degree of neutralization. The resulting SAPG exhibited distilled water absorption of 1033 g/g and 90 g/g in 0.9 wt.% NaCl solution, with a radiation dose of 5 kGy, a dose rate of 1.5 kGy/h, AA-to-AM mass ratio of 1.2, monomer-to-CS mass ratio of 7, and 90% AA neutralization.

Superabsorbent Polymers: Innovations in Ecology, Environmental, and Diverse Applications

Significant progress has been achieved in the development of superabsorbent polymers (SAPs), focusing on enhancing their performance and expanding their applications. Efforts are particularly directed at increasing water absorbency while promoting environmental sustainability. Biodegradable materials such as starch and potassium humate have been successfully integrated with SAPs for desert greening, improving water retention, salt resistance, and seedling survival. The inclusion of nutrient-rich organic-inorganic composites further enhances the durability, efficiency, and recyclability of SAPs. In drought mitigation, polymeric absorbent resins such as polyacrylamide and starch-grafted acrylates have shown efficacy in ameliorating soil conditions and fostering plant growth. In arid environments, agents enriched with humic acid and bentonite contribute to improved soil aeration and water retention, creating optimal conditions for plant establishment. Additionally, the adoption of innovative waste management solutions has led to the production of amphiphilic SAPs from residual sludge, effectively addressing soil nutrient deficiencies and environmental pollution. In the food industry, SAPs containing protease, tea polyphenols, and chitosan exhibit potential for enhancing the stability and quality of seafood products. These advancements highlight the growing relevance of structural optimization approaches in SAP development across diverse applications and underline the importance of continued innovation in these fields. As novel materials emerge and environmental challenges intensify, the potential applications of SAPs are anticipated to expand significantly.

Preparation of anti-leakage and salt-isolation absorbent polymer based on tragacanth gum

Superabsorbent polymers can be used to alleviate water scarcity and improve soil salinization. In this study, a superabsorbent polymer TG-g-PAA /BTCA was prepared by grafting acrylic acid to tragacanth gum (TG) with 1,2,3, 4-butane tetracarboxylic acid (BTCA) as crosslinking agent. The polymer can also effectively improve fertilizer utilization and reduce soil surface salinity. The polymers that exhibited optimum water absorption have been characterized by infrared spectroscopy, scanning electron microscopy and thermogravimetric analysis. Under optimum synthesis conditions, the maximum equilibrium absorption of TG-g-PAA/BTCA was 1341 g/g, 137 g/g, 72 g/g in deionized water, tap water and 0.9 wt% NaCl solution respectively. In addition, the anti-leakage and salt-isolation properties of TG-g-PAA/BTCA were investigated. The results showed that the addition of 0.6 % TG-g-PAA/BTCA improved the anti-leakage performance by 73.6 %. In addition, 0.4 % TG-g-PAA/BTCA effectively prevented the upward migration of salt ions. The interaction of polymers with functional groups in lateritic soils allows the polymers to adsorb on the surface of soil particles, thus forming soil aggregates, which reduces the permeability of water. The findings of this study can serve as the basis for effective application in agriculture.

Kinetic and isotherm studies on the adsorption of ionic liquids from aqueous solutions by carboxymethyl cellulose modified with sodium methacrylate sulfonate

A novel carboxymethyl cellulose (CMC) graft copolymer (CMC-g-PSMAS) was successfully synthesized by grafting sodium methacrylate sulfonate (SMAS) onto CMC. The resulting CMC-g-PSMAS was used to absorb 1-allyl-3-methylimidazole chloride ([Amim]Cl) ionic liquid. The effects of different experimental factors such as monomer dosage, temperature and time on the grafting yield were systematically studied. Adsorption studies demonstrated that the adsorption equilibrium could be achieved within 60 min. The theoretical maximum adsorption capacity of CMC-g-PSMAS for [Amim]Cl reached 69.2 mg·g-1. Compared to several kinetic and isothermal models, the adsorption process of [Amim]Cl onto CMC-g-PSMAS could be well-described by the pseudo-second-order model (R2 = 0.991) and the Langmuir model (R2 = 0.999), which was a typical chemical adsorption process. Adsorption thermodynamics analyses at 25 °C revealed that the adsorption process was spontaneous (ΔG = -33.37 KJ·mol-1) and exothermic (ΔH = -56.52 KJ·mol-1). The adsorption capacity of CMC-g-PSMAS was 35.3 mg·g-1 after eight cycles, indicating its good stability and recyclability. As a consequence, CMC-g-PSMAS was efficient in the adsorption of [Amim]Cl, which could be a potential candidate for removing ionic liquids in aqueous environments.

Quaternization-based graft modification of straw fibers for conditioning the sludge dewatering performance

Extracellular polymeric substances (EPS) are a critical influencing factor in sludge dewatering. Disrupting such EPS contributes to the release of bound water in sludge, enhancing the sludge dewatering performance. In This study, quaternized straw fibers that are destructive to the EPS structure and components in active sludge were prepared useing heterogeneous free radical graft polymerization. Straw fibers, dimethyl diallyl ammonium chloride (DMDAAC), ammonium persulfate (APS), and acrylamide (AM) were taken as the substrate, grafting monomer, catalyst, and cross-linking agent, respectively.The optimal processing conditions determined for the DMDAAC-based quaternization and graft modification of straw fibers were as follows: reaction temperature of 60 °C, reaction time of 5 h, 0.100 g of catalyst APS dosage per gram of straw, and 3.000 ml of DMDAAC dosage per gram of straw. The optimal processing conditions yielded 1.335 g of modified straw fibers per gram of straw, 33.67% grafting rate, and 31.70% substitution of the quaternary ammonium groups. The capillary suction time (CST) was conditioned from 243.3 ± 22.6 s in the original sludge to 134.5 ± 34.45 s. The specific resistance to filtration (SRF) was reduced from 8.82 ± 0.51 × 1012 m/kg in the original sludge to 4.59 ± 0.23 × 1012 m/kg.

Design and preparation of reticular superabsorbent hydrogel material with nutrient slow-release and high shear strength for ecological remediation of abandoned mines with steep slopes

In order to solve ecological remediation issues for abandoned mines with steep slopes, a kind of hydrogels with high cohesion and water-retaining were designed by inorganic mineral skeleton combining with polymeric organic network cavities. This eco-friendly hydrogel (MFA/HA-g-p(AA-co-AM)) was prepared with acrylic acid (AA)-acrylamide (AM) as network, which was grafted with humic acids (HA) as network binding point reinforcement skeleton and polar functional group donors, KOH-modified fly ash (MFA) as internal supporter. The maximum water absorption capacities were 1960 g/g for distilled water, which followed the pseudo-second-order model. This super water absorption was attributed to the first stage of 62 % fast absorption due to the high specific surface area, pore volume and low osmotic pressure, moreover, the multiple hydrophilic functional groups and network structure swell contributed to 36 % of the second stage slow adsorption. In addition, the pore filling of water in mesoporous channels contributed the additional 2 % water retention on the third stage. The high saline-alkali resistance correlated with the electrostatic attraction with MFA and multiple interactions with oxygen-containing functional groups in organic components. MFA and HA also enhanced the shear strength and fertility retention properties. After 5 cycles of natural dehydration and reabsorption process, these excellent characteristics of reusability and water absorption capacity kept above 97 %. The application of 0.6 wt% MFA/HA-g-p(AA-co-AM) at 15° slope could improve the growth of ryegrass by approximately 45 %. This study provides an efficient and economic superabsorbent material for ecological restoration of abandoned mines with steep slopes.

Biodegradable films from the lignocellulosic fibers of wheat straw biomass and the effect of calcium ions

Plastics are hazardous to human health, and plastic waste results in environmental pollution and ecological catastrophe. Biobased polymers from renewable sources have recently become promising for developing biodegradable packaging films. Among them, lignocellulosic residue from agricultural biomass is inexpensive, renewable, and biodegradable. This study aims to develop biodegradable films using lignocellulosic residue from wheat straw biomass. The methodology is a green process that solubilizes lignocellulosic chains using Zn2+ ions and crosslinks with Ca2+ ions of different concentrations (200-800 mM). The results reveal that the increase of Ca2+ ions significantly decreases moisture content, water solubility, water vapor permeability, transparency, and elongation of films. The tensile strength is recorded as 6.61 ± 0.07 MPa with the addition of 800 mM of CaCl2, which is approximately 2.5 times higher than commercial polyethylene films. Around 90 % of films biodegrade within a month in soil containing 20 % moisture content. Overall, lignocellulosic residue from wheat straw biomass could be an excellent replacement for synthetic polymer to fabricate strong, transparent, and biodegradable plastic films.

Enhanced Water Absorbency and Water Retention Rate for Superabsorbent Polymer via Porous Calcium Carbonate Crosslinking

To improve the water absorbency and water-retention rate of superabsorbent materials, a porous calcium carbonate composite superabsorbent polymer (PCC/PAA) was prepared by copolymerization of acrylic acid and porous calcium carbonate prepared from ground calcium carbonate. The results showed that the binding energies of C-O and C=O in the O 1s profile of PCC/PAA had 0.2 eV and 0.1-0.7 eV redshifts, respectively, and the bonding of -COO- groups on the surface of the porous calcium carbonate led to an increase in the binding energy of O 1s. Furthermore, the porous calcium carbonate chelates with the -COO- group in acrylic acid through the surface Ca2+ site to form multidirectional crosslinking points, which would increase the flexibility of the crosslinking network and promote the formation of pores inside the PCC/PAA to improve the water storage space. The water absorbency of PCC/PAA with 2 wt% porous calcium carbonate in deionized water and 0.9 wt% NaCl water solution increased from 540 g/g and 60 g/g to 935 g/g and 80 g/g, respectively. In addition, since the chemical crosslinker N,N'-methylene bisacrylamide is used in the polymerization process of PCC/PAA, N,N'-methylene bisacrylamide and porous calcium carbonate enhance the stability of the PCC/PAA crosslinking network by double-crosslinking with a polyacrylic acid chain, resulting in the crosslinking network of PCC/PAA not being destroyed after water absorption saturation. Therefore, PCC/PAA with 2 wt% porous calcium carbonate improved the water-retention rate by 244% after 5 h at 60 °C, and the compressive strength was approximately five-times that of the superabsorbent without porous calcium carbonate.

Synthesis of carboxymethyl cellulose-g-poly (acrylic acid-co-acrylamide)/polyvinyl alcohol sponge as a fast absorbent composite and its application in coral sand soil

To improve the rapid absorption capacity of coral sand soil for rainfall, a composite of carboxymethyl cellulose-g-poly (acrylic acid-co-acrylamide)/polyvinyl alcohol sponge (CMC-g-P(AA-co-AM)/PVA) was designed and synthesized by coupling CMC-g-P(AA-co-AM) granules with a PVA sponge. The results showed that the rapid water absorption of CMC-g-P (AA-co-AM)/PVA in distilled water in 1 h was 26.45 g/g, twice that of CMC-g-P(AA-co-AM) and the PVA sponge, which is suitable for short-term rainfall. In addition, the cation had a slight influence on the water absorption capacity of CMC-g-P (AA-co-AM)/PVA, which were 29.5 and 18.9 g/g in 0.9 wt% NaCl and CaCl₂ solutions, respectively, indicating the great adaptability of CMC-g-P (AA-co-AM)/PVA to high‑calcium coral sand. With the addition of 2 wt% CMC-g-P (AA-co-AM)/PVA, the water interception ratio of the coral sand increased from 13.8 % to 23.7 %, and 54.6 % of the total interception water remained after 15-day evaporation. Moreover, pot experiments demonstrated that 2 wt% CMC-g-P(AA-co-AM)/PVA in coral sand enhanced plant development under water scarcity, suggesting that CMC-g-P (AA-co-AM)/PVA is a promising soil amendment for coral sand soils.