Two-leg alternate loading model--a different approach to biomechanical investigations of fixation methods of the injured pelvic ring with focus on the pubic symphysis

Development and preclinical evaluation of a cable-clamp fixation device for a disrupted pubic symphysis

BACKGROUND

Traumatic separation of the pubic symphysis can destabilize the pelvis and require surgical fixation to reduce symphyseal gapping. The traditional approach involves open reduction and the implantation of a steel symphyseal plate (SP) on the pubic bone to hold the reposition. Despite its widespread use, SP-fixation is often associated with implant failure caused by screw loosening or breakage.

METHODS

To address the need for a more reliable surgical intervention, we developed and tested two titanium cable-clamp implants. The cable served as tensioning device while the clamp secured the cable to the bone. The first implant design included a steel cable anterior to the pubic symphysis to simplify its placement outside the pelvis, and the second design included a cable encircling the pubic symphysis to stabilize the anterior pelvic ring. Using highly reproducible synthetic bone models and a limited number of cadaver specimens, we performed a comprehensive biomechanical study of implant stability and evaluated surgical feasibility.

RESULTS

We were able to demonstrate that the cable-clamp implants provide stability equivalent to that of a traditional SP-fixation but without the same risks of implant failure. We also provide detailed ex vivo evaluations of the safety and feasibility of a trans-obturator surgical approach required for those kind of fixation.

CONCLUSION

We propose that the developed cable-clamp fixation devices may be of clinical value in treating pubic symphysis separation.

Postoperative stability following a triple pelvic osteotomy is affected by implant configuration: a finite element analysis

BACKGROUND

The triple pelvic osteotomy is an established surgical method with multiple modifications regarding surgical technique and choice of implant. The stability of the osteotomy is affected by numerous factors, and among these, the three-dimensional implant configuration is a scientifically less explored aspect.

METHODS

We used a finite element model of a hemi-pelvis with a standardized triple osteotomy to calculate relative flexibility for loads in all translational degrees of freedom for five different implant configurations. Two of the configurations used entry points only feasible when implant removal was not necessary.

RESULTS

The stability of the osteotomy improved with an increased distance between the implants in the plane of the osteotomy as well as for a more perpendicular angle relative to the osteotomy plane. The implant configurations with more entry points available made this easier to adhere to.

CONCLUSION

The use of bioabsorbable implants may provide better opportunities for optimal implant constructs which can, to a certain degree, compensate for the lesser mechanical stiffness of bioabsorbable polymers as compared to metal implants.

Biomechanical in vitro analysis of a novel flexible implant for pubic symphysis disruption using an ultra-high molecular weight polyethylene fiber cord

BACKGROUND

Plate osteosynthesis depicts the gold standard to surgically treat pubic symphysis disruptions. However, high rates of implant failure after plate osteosynthesis are reported, probably because of the iatrogenic arthrodesis of this fibrocartilaginous joint. Therefore, flexible implants for treatment of pubic symphysis disruptions appear to be a sensible solution.

METHODS

In this biomechanical screening study, we designed and investigated a flexible implant, which consists of two plates connected with an ultra-high molecular weight polyethylene fiber cord. We mechanically tested eye splices as a possible fixation method of the cords by performing tensile load to failure tests. Afterwards, we developed a biomechanically appropriate plate design and cord routing between the plates. Finally, we biomechanically tested the flexible implant under tensile and shear loading until failure.

FINDINGS

When fixing a 1 mm ultra-high molecular weight polyethylene fiber cord with eye splices, a load at failure of 1570.74 N was detected under tensile loading. None of the eye splices failed but the cords itself ruptured. The load at failure of the designed cord routing in criss-cross technique and fixation within the plates amounts 4742.09 N under tensile and 2699.77 N under shear load.

INTERPRETATION

We developed a novel flexible implant for repair of pubic symphysis disruptions using ultra-high molecular weight polyethylene fiber cords connected to osteosynthesis plates. We identified eye splices as a mechanically optimal fixation method and proved that the ultra-high molecular weight polyethylene fiber cord routing and fixation of the flexible implant clearly withstands physiological forces acting on the pubic symphysis.

Comparison of Biomechanical Performance of Five Different Treatment Approaches for Fixing Posterior Pelvic Ring Injury

Background

A large number of pelvic injuries are seriously unstable, with mortality rates reaching 19%. Approximately 60% of pelvic injuries are related to the posterior pelvic ring. However, the selection of a fixation method for a posterior pelvic ring injury remains a challenging problem for orthopedic surgeons. The aim of the present study is to investigate the biomechanical performance of five different fixation approaches for posterior pelvic ring injury and thus provide guidance on the choice of treatment approach in a clinical setting.

Methods

A finite element (FE) model, including the L3-L5 lumbar vertebrae, sacrum, and full pelvis, was created from CT images of a healthy adult. Tile B and Tile C types of pelvic fractures were created in the model. Five different fixation methods for fixing the posterior ring injury (PRI) were simulated: TA1 (conservative treatment), TA2 (S1 screw fixation), TA3 (S1 + S2 screw fixation), TA4 (plate fixation), and TA5 (modified triangular osteosynthesis). Based on the fixation status (fixed or nonfixed) of the anterior ring and the fixation method for PRI, 20 different FE models were created. An upright standing loading scenario was simulated, and the resultant displacements at the sacroiliac joint were compared between different models.

Results

When TA5 was applied, the resultant displacements at the sacroiliac joint were the smallest (1.5 mm, 1.6 mm, 1.6 mm, and 1.7 mm) for all the injury cases. The displacements induced by TA3 and TA2 were similar to those induced by TA5. TA4 led to larger displacements at the sacroiliac joint (2.3 mm, 2.4 mm, 4.8 mm, and 4.9 mm), and TA1 was the worst case (3.1 mm, 3.2 mm, 6.3 mm, and 6.5 mm).

Conclusions

The best internal fixation method for PRI is the triangular osteosynthesis approach (TA5), followed by S1 + S2 screw fixation (TA3), S1 screw fixation (TA2), and plate fixation (TA4).

Biomechanical analysis of anterior pelvic ring fractures with intact peripelvic soft tissues: a cadaveric study

PURPOSE

Biomechanical studies of the pelvis are usually performed using dissected pelvic specimens or synthetic bones. Thereby the stabilising effect of the surrounding soft tissues is analysed insufficiently. Biomechanical data for isolated anterior pelvic ring fractures are currently missing. Therefore, the purpose of this study was to develop a novel testing device for biomechanical analyses of the pelvis and to investigate two different anterior pelvic ring fractures in a cadaveric model with intact peripelvic soft tissues.

METHODS

A new biomechanical table construction which enables the fixation and testing of complete cadaveric specimens was developed. It was used to investigate the relative motion and stiffness changes due to unilateral osteotomy of the superior and inferior pubic ramus. Five cadavers with a mean age of 55.6 years (± 15.53 years) were included and loaded with a sinusoidal, cyclic (1 Hz), compressive force of up to 365 N over ten cycles for each condition.

RESULTS

Biomechanical testing of the pelvis with complete appended soft tissues was feasible. Native stiffness without a pelvic fracture was 64.31 N/mm (± 8.33 N/mm). A standardised unilateral osteotomy of the superior pubic ramus reduced the stiffness under isolated axial load by 2% (63.05 N/mm ± 7.45 N/mm, p = 0.690). Additional osteotomy of the inferior pubic ramus caused a further, statistically not significant, decrease by 5% (59.57 N/mm ± 6.84 N/mm, p = 0.310).

CONCLUSIONS

The developed test device was successfully used for biomechanical analyses of the pelvis with intact peripelvic soft tissues. In a first study, isolated unilateral fractures of the anterior pelvic ring showed no relevant biomechanical variation compared to the intact situation under isolated axial load. Only 7% of the measured stiffness was created by both unilateral pubic rami. Therefore, the clinical practice to treat unilateral anterior pelvic ring fractures conservatively is supported by the results of this study.

Individuals with sacroiliac joint dysfunction display asymmetrical gait and a depressed synergy between muscles providing sacroiliac joint force closure when walking

Walking is often compromised in individuals with low back and hip disorders, such as sacroiliac joint dysfunction (SIJD). The disorder involves reduced coactivation of the gluteus maximus and contralateral latissimus dorsi, which together provide joint stability during walking. The purpose of our study was to compare the kinematics and contributions of selected muscles to identified synergies during walking between healthy individuals and those with SIJD. Six women with unilateral SIJD and six age-matched healthy controls walked on a force-measuring treadmill at 1 m/s while we recorded kinematics and the activity of 16 muscles with surface EMG. Non-negative matrix factorization was used to identify patterns of EMG activity (muscle synergies). Individuals with SIJD exhibited less hip extension and lower peak vertical ground reaction forces on the affected side than the unaffected side. In contrast to controls, the SIJD group also displayed a depressed muscle synergy between gluteus maximus on the affected side and the contralateral latissimus dorsi. The results indicate that individuals with SIJD exhibited both reduced activation of gluteus maximus during a loading synergy present in walking and greater asymmetry between legs when walking compared with age-matched controls.

Biomechanics of unilateral and bilateral sacroiliac joint stabilization: laboratory investigation

OBJECTIVE Bilateral symptoms have been reported in 8%-35% of patients with sacroiliac (SI) joint dysfunction. Stabilization of a single SI joint may significantly alter the stresses on the contralateral SI joint. If the contralateral SI joint stresses are significantly increased, degeneration may occur; alternatively, if the stresses are significantly reduced, bilateral stabilization may be unnecessary for patients with bilateral symptoms. The biomechanical effects of 1) unilateral stabilization on the contralateral SI joint and 2) bilateral stabilization on both SI joints are currently unknown. The objectives of this study were to characterize bilateral SI joint range of motion (ROM) and evaluate and compare the biomechanical effects of unilateral and bilateral implant placement for SI joint fusion. METHODS A lumbopelvic model (L5-pelvis) was used to test the ROM of both SI joints in 8 cadavers. A single-leg stance setup was used to load the lumbar spine and measure the ROM of each SI joint in flexion-extension, lateral bending, and axial rotation. Both joints were tested 1) while intact, 2) after unilateral stabilization, and 3) after bilateral stabilization. Stabilization consisted of lateral transiliac placement of 3 triangular titanium plasma-sprayed (TPS) implants. RESULTS Intact testing showed that during single-leg stance the contralateral SI joint had less ROM in flexion-extension (27%), lateral bending (32%), and axial rotation (69%) than the loaded joint. Unilateral stabilization resulted in significant reduction of flexion-extension ROM (46%) on the treated side; no significant ROM changes were observed for the nontreated side. Bilateral stabilization resulted in significant reduction of flexion-extension ROM of the primary (45%) and secondary (75%) SI joints. CONCLUSIONS This study demonstrated that during single-leg loading the ROMs for the stance (loaded) and swing (unloaded) SI joints are significantly different. Unilateral stabilization for SI joint dysfunction significantly reduces the ROM of the treated side, but does not significantly reduce the ROM of the nontreated contralateral SI joint. Bilateral stabilization is necessary to significantly reduce the ROM for both SI joints.

Symphyseal fixation in open book injuries cannot fully compensate anterior SI joint injury-A biomechanical study in a two-leg alternating load model

INTRODUCTION

In open book injuries type Tile B1.1 or B1.2 also classified as APC II (anteroposterior compression), it remains controversial, if a fixation of the anterior ring provides sufficient stability or a fixation of the posterior ring should be included. Therefore the relative motion at the sacroiliac joint was quantified in a two-leg alternating load biomechanical pelvis model in the intact, the injured and the restored pelvis.

METHODS

Fresh-frozen intact (I) pelvises (n = 6) were subjected to a non-destructive cyclic test under sinosuidal axial two-leg alternating load with progressively increasing amplitude. Afterwards an open book injury (J) including the anterior ligament complex of the left sacroiliac joint, the sacrospinal and sacrotuberal ligaments (Tile B1.1) was created and the specimens were retested. Finally, the symphysis was stabilized with a modular fixation system (1-, 2- or 4-rod configuration) (R) and specimens were cyclically retested. Relative motion at the sacroiliac joint was captured at both sacroiliac joints by motion tracking system at two load levels of 170 N and 340 N during all tests.

RESULTS

Relative sacroiliac joint movements at both load levels were significantly higher in the J-state compared to the I-state, excluding superoinferior translational movement. With exception of the anteroposterior translational movement at 340N, the relative sacroiliac joint movements after each of the three reconstructions (1-, 2-, 4-rod fixation) were significantly smaller compared to the J-state and did not differ significantly to the I-state, but stayed above the values of the latter. Relative movements did not differ significantly in a direct comparison between the 1-rod, 2-rod and 4-rod fixations.

CONCLUSION

Symphyseal locked plating significantly reduces relative movement of the sacroiliac joint in open book injuries type Tile B1.1 or B1.2 (APC II) but cannot fully restore the situation of the intact sacroiliac joint.

Biomechanical study of different fixation techniques for the treatment of sacroiliac joint injuries using finite element analyses and biomechanical tests

The pelvis is one of the most stressed areas of the human musculoskeletal system due to the transfer of truncal loads to the lower extremities. Sacroiliac joint injury may lead to abnormal joint mechanics and an unstable pelvis. Various fixation techniques have been evaluated and discussed. However, it may be difficult to investigate each technique due to variations in bone quality, bone anatomy, fracture pattern, and fixation location. Additionally, the finite element method is one useful technology that avoids these variations. Unfortunately, most previous studies neglected the effects of the lumbar spine and femurs when they investigated the biomechanics of pelvises. Thus, the aim of this study was to investigate the biomechanical performance of intact, injured, and treated pelvises using numerical and experimental approaches. Three-dimensional finite element models of the spine-pelvis-femur complex with and without muscles and ligaments were developed. The intact pelvis, the pelvis with sacroiliac joint injury, and three types of pelvic fixation techniques were analyzed. Concurrently, biomechanical tests were conducted to validate the numerical outcomes using artificial pelvises. Posterior iliosacral screw fixation showed relatively better fixation stability and lower risks of implant failure and pelvic breakage than sacral bar fixation and a locking compression plate fixation. The present study can help surgeons and engineers understand the biomechanics of intact, injured, and treated pelvises. Both the simulation technique and the experimental setup can be applied to investigate different pelvic injuries.

Safety and effectiveness of minimally invasive sacroiliac joint fusion in women with persistent post-partum posterior pelvic girdle pain: 12-month outcomes from a prospective, multi-center trial

Postpartum posterior pelvic girdle pain (PPGP) affects nearly 20 % of women who experience back pain in the peripartum period. The sacroiliac joint is a source of this pain in 75 % of women with persistent PPGP. A subset of women will fail to obtain acceptable pain relief from the current array of non-surgical treatment options. The purpose of this study is to assess the safety and effectiveness of minimally invasive sacroiliac (SI) joint fusion in women with chronic SI joint dysfunction whose pain began in the peri-partum period whose symptoms were recalcitrant to non-surgical management. A sub-group analysis of subjects with sacroiliac joint disruption and/or degenerative sacroiliitis enrolled in a prospective, multi-center trial of SI joint fusion was performed. Subjects with PPGP were identified and compared with women without PPGP and with men. Of 172 enrolled subjects, 52 were male, 100 were females without PPGP and 20 females had PPGP. PPGP subjects were significantly younger (43.3 years, vs. 52.8 for females without PPGP and 50.5 for men, p = 0.002). There were no differences in any other demographic or baseline clinical measure. Women with PPGP experienced a significant improvement in pain (−51 mm on VAS), function (−20.6 pts on ODI) and quality of life (SF-36 PCS +10.4, MCS +7.2, EQ-5D +0.31) at 12 months after surgery. These improvements were characteristic of the overall study results; no difference was detected between sub-groups. The sacroiliac joint can be a source of pain in women with persistent PPGP and should be investigated as a pain generator. In this study, women with carefully diagnosed chronic SI joint pain from PPGP recalcitrant to conservative therapies experienced clinically beneficially improvements in pain, disability and quality of life after minimally invasive SI joint fusion using a series of triangular porous plasma spray coated implants.

The influence of simulated transversus abdominis muscle force on sacroiliac joint flexibility during asymmetric moment application to the pelvis

BACKGROUND

The role of so-called local muscle system in motor control of the lower back and pelvis is a subject of ongoing debate. Prevailing beliefs in stabilizing function of this system were recently challenged. This study investigated the impact of in vitro simulated force of transversely oriented fibres of the transversus abdominis muscle (a part of the local system) on flexibility of the sacroiliac joint during asymmetric moment application to the pelvis.

METHODS

In 8 embalmed specimens an incremental moment was applied in the sagittal plane to one innominate with respect to the fixed contralateral innominate. Ranges of motion of the sacroiliac joint were recorded using the Vicon Motion Capture System. Load-deformation curves were plotted and flexibility of the sacroiliac joint was calculated separately for anterior and posterior rotations of the innominate, with and without simulated muscle force.

FINDINGS

Flexibility of the sacroiliac joint was significantly bigger during anterior rotation of the innominate, as compared to posterior rotation (Anova P<0.05). After application of simulated force of transversus abdominis, flexibility of the joint did not change both during anterior and posterior rotations of the innominate.

INTERPRETATION

A lack of a stiffening effect of simulated transversus abdominis force on the sacroiliac joint was demonstrated. Earlier hypotheses suggesting a stiffening influence of this muscle on the pelvis cannot be confirmed. Consistent with previous findings smaller flexibility of the joint recorded during posterior rotation of the innominate may be of clinical importance for physio- and manual therapists. However, major limitations of the study should be acknowledged: in vitro conditions and simulation of only solitary muscle force.

Is sacroiliac joint pain associated with changes in the pubic symphysis? A radiographic pilot study

BACKGROUND CONTEXT

Disorders of the sacroiliac joint are challenging to diagnose. This is partially due to similarity in symptom presentation to other lumbar spinal disorders and poor visibility of the joint on imaging studies. The pubic symphysis is clearly visualized in the anteroposterior view on plain film radiographs. As a closed ring, changes in the anterior and posterior portion of the pelvis may be reciprocal. The purpose of this study was to assess the correlation between pubic symphyseal changes observed on X-ray and SI joint disorders.

METHODS

Thirty patients with a confirmed diagnosis of SI joint disorders were compared with 30 patients with low back pain without the evidence of SI joint involvement. Plain film radiographs were blinded and independently reviewed by two orthopedic surgeons. Changes in the pubic symphysis were classified as (0) no change, (1) osteoarthritic degeneration, (2) vertical displacement, or (3) ligament ossification.

RESULTS

There was no significant difference between groups in age, gender, or parturition status. The majority of both groups were female. Mean (±SD) subject age was 61 (±11) and 59 (±9) years, and parity was 44% and 39% for the study and control groups, respectively. The prevalence of observable changes in the pubic symphysis was 97% in the study group and 30% in the control group (p < 0.001).

CONCLUSION

Results of this study suggest that pubic symphyseal changes in the presence of low back pain and positive provocative maneuvers could serve as a marker for SI joint disease. Further investigation of the potential relationship between SI joint symptoms and symphyseal changes should be examined.

Influence of flexible fixation for open book injury after pelvic trauma--a biomechanical study

BACKGROUND

Implant loosening is frequently detected after fixation of open book injuries. Though many authors do not see this as a complication, it is often the reason for hardware removal or reinstrumentation in the case of remaining instability. We hypothesized that the flexibility of the implant has an influence on loosening and thus on failure of the construct.

METHODS

We used 6 fresh-frozen pelvic specimens and tested them with our recently introduced test setup for two-leg alternate loading. We subjected them to a non-destructive quasi-static test in the intact condition followed by a non-destructive cyclic test under axial sinusoidal loading with progressive amplitude. Afterwards we simulated an open book injury and performed fixation with three different configurations of a modular fixation system (1-, 2- or 4-rod configuration) in randomized order. Subsequently, the specimens were subjected to 3 cyclic tests with the same loading protocol as previously defined. Finally, each construct was cyclically tested to failure keeping the final rod configuration.

FINDINGS

We detected significantly greater mobility after 1-rod-fixation and no significant differences after 2-rod or 4-rod-fixation compared to the intact symphysis condition. In the destructive test series the 4-rod-fixation failed first followed by the 1-rod-fixation. The 2-rod-fixation sustained almost 3 times as many load cycles prior to failure as the 4-rod-fixation, whereas the 1-rod-fixation sustained twice as many cycles as the 4-rod-fixation.

INTERPRETATION

In conclusion, flexible fixation of the ruptured pubic symphysis in human specimens shows superior behavior with respect to load bearing capacity and ability to withstand cyclic loading compared to stiff constructs.