Five-year clinical outcome of posterior zirconia ceramic inlay-retained FDPs with a modified design

Durability of resin bonding to translucent zirconia materials: An in vitro study

STATEMENT OF PROBLEM

How the yttria content (3Y-PSZ, 4Y-PSZ and 5Y-PSZ) affects the tensile bond strength of luting resin to translucent zirconia ceramics is unclear.

PURPOSE

The purpose of this in vitro study was to evaluate whether the bond strength of resin to translucent zirconia ceramics and its durability are influenced by the yttria content (3Y-PSZ, 4Y-PSZ and 5Y-PSZ).

MATERIAL AND METHODS

Sixty-four disk-shaped specimens of zirconia ceramics were randomly allocated to 4 groups (n=16) with respect to the yttria concentration: GHT: 3 mol% yttria-partially stabilized zirconia 3Y-PSZ; GHTML: 3 mol% yttria-partially stabilized multilayered zirconia 3Y-PSZ; GSTML: 4 mol% yttria-partially stabilized zirconia 4Y-PSZ; and GUTML: 5 mol% yttria-partially stabilized zirconia 5Y-PSZ. For bonding, acrylic resin tubes were filled with composite resin and bonded to the zirconia disks using adhesive luting resin by following manufacturer's instructions. Half of each main group (n=8) was stored in water for 3 days at 37 °C. The other half was stored in water for 150 days with 37 500 thermocycles (5 to 55 °C). The tensile bond strength test was determined with a universal testing machine at a crosshead speed of 2 mm/minute using a chain loop for alignment.

RESULTS

The tensile bond strength was not significantly affected by the yttria concentration of different zirconia materials (3Y-PSZ, 4Y-PSZ, and 5Y-PSZ, P=.17). The mean ±standard deviation failure loads for groups ranged from 24.1 ±2.6 MPa for the ultratranslucent multilayered zirconia (with thermocycling) to 52.7 ±5.4 MPa for the high translucent multilayered zirconia (without thermocycling). However, artificial aging adversely affected the tensile bond strength values for all tested zirconia systems (P<.001). Scanning electron microscope evaluation showed that cohesive fracture was the predominant failure mode, while few specimens exhibited adhesive failure at the interface.

CONCLUSIONS

The yttria concentration (3Y-PSZ, 4Y-PSZ, and 5Y-PSZ) had no significant effect on the bond strength of different zirconia ceramics (P=.17), whereas the artificial aging procedures led to a statistically significant decrease in tensile bond strength (P<.001).

Shear bond strength of resin cement to additively manufactured zirconia with customized surface texture and porosity: Part 1

STATEMENT OF PROBLEM

The additive manufacturing of zirconia has been reported to present promising mechanical properties. However, studies on bonding to additively manufactured (AM) zirconia are lacking.

PURPOSE

The purpose of this in vitro study was to investigate the effect of customized porosity and surface texture on the shear bond strength (SBS) of resin cement to 3-dimensionally (3D) printed zirconia.

MATERIAL AND METHODS

A total of 60 zirconia disks (Ø12×5 mm) were designed with different surface porosity using a computer-aided design (CAD) software program and manufactured via stereolithography (SLA) 3D printing. The disks were divided into 4 groups (n=15) based on surface texture and porosity: Control (no designed porosities), G1:50 (50×50-µm pores 200 µm apart), G2:100 (100×100-µm pores 400 µm apart), and G3:200 (200×200-µm pores 800 µm apart). The specimens were cleaned, and the binder removed before sintering. The microstructural analysis of the specimen's surface before SBS was performed using a profilometer to determine surface texture (n=5). SBS was measured using a universal testing machine, and thermal cycling was performed to simulate aging (n=10). Data for SBS were analyzed using 2-way ANOVA (α=.05).

RESULTS

Surface texture and porosities were confirmed by profilometry. In all comparisons, the G3:200 group demonstrated the highest mean SBS with 8.78 MPa (P<.001); however, it was similar to the Control group, which had a mean of 8.41 MPa (P=.631). The G1:50 showed significantly lower SBS values at 3.90 MPa (P<.001), followed by the G2:100 group with 5.14 MPa (P<.001). Thermal cycling generally decreased SBS in all groups (P<.001).

CONCLUSIONS

Customized surface textures can improve bond strengths, with larger pores (200×200 µm) providing values comparable with those of traditional mechanical pretreatments surfaces, while smaller pores resulted in lower bond strengths. This approach avoids surface damage and phase transitions caused by traditional treatments. These findings provide a foundation for future research aimed at developing more durable and reliable zirconia restorations, ultimately enhancing clinical outcomes.

Posterior two-unit cantilevered zirconia resin-bonded fixed partial dentures: A 3-year prospective single-arm clinical trial

OBJECTIVES

To evaluate the longevity of cantilevered zirconia-based resin-bonded fixed partial dentures (RBFPDs) in replacing missing posterior teeth, as well as the quality of life and patient satisfaction experienced by those receiving zirconia RBFPDs.

METHODS

A prospective single-arm uncontrolled clinical trial was conducted to replace one or more missing premolars or molars with a span of 5 to 8 mm using cantilevered zirconia RBFPDs. Thirty-six participants with 40 prostheses were recruited and underwent a 3-year clinical evaluation. The retainer designs included a minimum thickness of 0.8 mm, a minimum of 200° circumferential wraparound with an occlusal bar, and a connector dimension of 3 × 3 mm. Patient-reported outcomes, including patient satisfaction and Oral Health Impact Profile (OHIP), were assessed.

RESULTS

The average age of participants was 45.8 years, and 72.5 % were women. The success rate of the posterior zirconia RBFPDs was 76.2 %, with an estimated mean success duration of 46.1 months. The survival rate was 88.1 %, with an estimated mean survival duration of 49.4 months. Participants were highly satisfied with the treatment, achieving an average satisfaction score of 80.8 ± 11.9. Participants' total OHIP scores decreased from 52.3 to 39.6 after 3 years, indicating a significant improvement in oral health-related quality of life (P = 0.009).

CONCLUSIONS

After 3 years, a moderately high survival rate and favourable patient-reported outcomes of posterior cantilevered zirconia RBFPDs were achieved. Therefore, it can be recommended as a conservative treatment option to replace missing posterior teeth, provided that retainer design considerations are taken into account.

CLINICAL SIGNIFICANCE

Cantilevered zirconia RBFPDs for posterior teeth can serve as a conservative treatment option that is both aesthetically pleasing and biocompatible. It offers a more cost-effective alternative compared to dental implants, which are often prohibitively expensive for the majority of patients. This approach has the potential to greatly improve patient-reported outcomes.

Marginal fit and retention force of zirconia resin-bonded fixed dental prostheses in the posterior region with different designs

Background/purpose

Retainer debonding of resin-bonded fixed dental prostheses (RBFDPs) is one of the major reasons for their lower survival rates than fixed dental prostheses (FDPs) with full-coverage crowns. Recent advances in milling technology have enabled the fabrication of RBFDPs with complex retainers (D-shaped designs). This study aimed to assess the marginal fit and retention force of zirconia RBFDPs with inlay-, L-, and D-shaped designs to clarify their clinical applications.

Materials and methods

Three abutment teeth models without maxillary second premolars were created using inlay-, L-, and D-shaped retainer designs. The zirconia RBFDPs were designed and fabricated according to the manufacturer's instructions (n = 10). The marginal gap was measured using the silicone replica technique. Zirconia frameworks were bonded to the abutment teeth using resin cement. Tensile test was conducted after thermal cycling and dynamic loading tests. The loads during debonding or fracture were recorded. The failure pattern was analyzed by observing the fracture surface using a scanning electron microscope.

Results

D-shaped RBFDPs showed a significantly larger marginal gap than inlay- and L-shaped RBFDPs (P < 0.05). However, the mean marginal values were clinically acceptable (<120 μm). The D-shaped model exhibited the highest tensile strength in the tensile tests. The inlay-shaped and most of the D-shaped RBFDPs experienced debonding with cohesive failure, whereas the L-shaped RBFDPs showed fractures near the connector.

Conclusion

The D-shaped retainer design was superior to the inlay- and L-shaped designs with respect to the inhibition of retainer debonding. However, the marginal fitness needs to be improved.

Long-term clinical outcome of three-unit fixed-fixed posterior zirconia ceramic inlay-retained FDPs with a modified design

OBJECTIVES

To assess the long-term clinical outcome of posterior inlay-retained fixed dental prostheses (IRFDPs) with a modified design made from zirconia ceramic.

METHODS

In 30 patients thirty 3-unit IRFDPs were placed to replace 7 premolars (4 in the maxilla, 3 in the mandible), and 23 first molars (15 in the maxilla, 8 in the mandible). Preparations were accomplished in agreement with the general principles for ceramic inlay restorations and modified with a short retainer-wing bevel preparation within the enamel at the buccal and oral sides. The frameworks were milled from 3Y-TZP ceramic, and the pontics were veneered with feldspathic ceramic. All IRFDPs were bonded with a phosphate monomer containing luting resin after air-abrasion of the intaglio surfaces. The patients were recalled 6-12 months after placement, and then annually. Kaplan-Meier analysis was used to calculate the survival and complication rates of the IRFDPs.

RESULTS

The mean observation time was 10.6 ± 1.5 years. The 10-year cumulative survival rate was 89% with 4 failures, two of them were due to deep secondary caries with loss of retention, one due to repeated debonding with enamel fractures, and one due to generalized progressive periodontitis. The most common complication was chipping of the veneering ceramic (20.1%). Eighteen IRFDPs were free of any type of complication up to 15.4 years, which corresponds to a 10-year cumulative success rate of 70.4%.

CONCLUSION

The long-term clinical performance of modified IRFDPs made of veneered zirconia ceramics was favorable after 10 years, therefore, they represent a treatment alternative to replace posterior single missing teeth.

CLINICAL SIGNIFICANCE

Zirconia-based IRFDPs fabricated in the modified design may represent a substance-preserving alternative to conventional posterior FDPs to replace posterior single missing teeth, particularly in cases where implants cannot be placed, and when the adjacent teeth already have small restorations or defects.

Evaluation of different designs for posterior cantilever zirconia inlay-retained fixed dental prostheses in missing tooth replacement: Stage one results with 18-month follow-up assessment

OBJECTIVES

This clinical study aimed to investigate the outcomes and survival rates of different variations of inlay-retained fixed dental prostheses (IR-FDPs) composed of monolithic zirconia ceramic. The IR-FDPs with a single-retainer design were used for replacing missing mandibular second premolars. The research evaluated the effectiveness and longevity of these prostheses in clinical settings.

METHODS

A total of 30 IR-FDPs (n = 30) were placed for 27 female patients who presented with missing mandibular second premolar teeth. For this study, the mandibular first molar was chosen as a retainer for the cantilever IR-FDPs and the study involved a random assignment of participants into three distinct groups, each comprising 10 individuals (n = 10). The criterion for the grouping was the retainer design: inlay ring (IR), lingual coverage (LC), and occlusal coverage (OC). The three groups included mesial inlay box with the same dimensions (3 mm height, 3 mm width and 2 mm depth). All IR-FDPs were manufactured using monolithic high translucent 3Y zirconia and the connector area to the cantilever pontic was adjusted to dimensions of 3 × 3 mm for all designs. The restorations were bonded using adhesive resin cement. The clinical and radiographic evaluations of the restorations were conducted for a duration of 18 months, following the modified FDI (World Dental Federation) criteria.

RESULTS

The restorations were observed in stage one for a period of 18 months. Only one restoration in group LC was debonded after 10 months and re-bonded. The clinical quality of all crowns and the patient's satisfaction were high. No adverse soft tissue reactions around the crowns were observed and only one abutment in group IR was endodontically treated after 12 months.

CONCLUSIONS

Zirconia cantilever IR-FDPs offer a viable short-term treatment option for replacing missing posterior teeth, providing esthetic and functional benefits while minimizing invasiveness. Over an 18-month observation period, these prostheses have demonstrated a remarkable survival rate of 100% and a success rate of 96.6%. These findings suggest the effectiveness and reliability of zirconia cantilever IR-FDPs as a short-term solution for replacing missing posterior teeth.

CLINICAL SIGNIFICANCE

Zirconia cantilever IR-FDPs could present a practical solution for addressing posterior tooth loss, especially in cases where implant placement is not recommended and conventional fixed dental prostheses entail excessive invasiveness.

Effects of ceramic type, connector dimension, and thermomechanical-aging on the fracture resistance and fit of CAD-CAM produced inlay-retained fixed partial dentures

The purpose of the present study is to evaluate the fracture resistance and the fit of CAD-CAM produced inlay-retained fixed partial dentures. Eighteen experimental groups were generated according to different CAD-CAM ceramic materials (zirconia, lithium disilicate, and zirconia-reinforced lithium silicate), different connector dimensions (12, 14, and 16 mm²), and application of thermomechanical-aging (1,200,000 cycles of cyclic loading with simultaneous thermal cycling). Gap values of thermomechanically-aged groups were measured by using periapical radiographs. Then, the specimens were tested for fracture resistance and failure types were examined. The results were statistically analyzed (α=0.05). Higher gap values were observed after aging. Zirconia showed the highest fracture resistance values among the most of the experimental groups. In non-aged groups, the most frequent failure type was decementation in zirconia group. In the aged groups, the most frequent failure type was molar connector fracture. Thermomechanical-aging increased the gap values and decreased the fracture resistance values.

Durability of cantilever inlay-retained fixed dental prosthesis fabricated from multilayered zirconia ceramics with different designs

PURPOSE

The purpose of this in-vitro study was to investigate the effect of framework design on fracture resistance and failure modes of cantilever inlay-retained fixed partial dentures (IRFDPs) fabricated from two multilayered monolithic zirconia materials.

MATERIALS AND METHODS

Seventy-two natural premolar teeth were prepared as abutments for cantilever IRFDPs using three designs: mesial-occlusal (MO) inlay with short buccal and palatal wings (D1), MO inlay with long palatal wing (D2), MO inlay with long palatal wing and occlusal extension (D3). Full-contoured IRFDPs were fabricated from two monolithic zirconia materials; IPS e.max ZirCAD Prime and Zolid Gen-X. Adhesive surfaces were air-abraded and bonded with MDP-containing resin cement. Specimens were subjected to thermocycling (5-55 °C, 5000 cycles); then, mechanical loading (1.2 × 10⁶ cycles, 49 N). Surviving specimens were loaded until failure in the universal testing machine. All specimens were examined under stereomicroscope, and two samples from each group were evaluated using Scanning Electron Microscope.

RESULTS

Mean failure loads were not significantly different between different framework designs or between two materials. However, IPS e.max ZirCAD Prime showed significantly higher failure rate than Zolid Gen-X during dynamic fatigue (p = 0.009). Samples with D1 design showed higher debonding rate, D2 failed mainly by fracture of the palatal wing and debonding, and D3 failed mainly by fracture of the abutment tooth. Debonded restorations showed mainly mixed failures.

CONCLUSION

Cantilever IRFDPs with framework designs that maximize adhesion to enamel exhibited promising results. IPS e.max ZirCAD Prime was more susceptible to fractures with the long palatal wing design.

Do tooth-supported zirconia restorations present more technical failures related to fracture or loss of retention? Systematic review and meta-analysis

OBJECTIVES

This systematic review was performed to determine the main cause of technical failure of tooth-supported zirconia crowns and fixed partial dentures (FPDs), categorizing them as fracture/chipping or loss of retention/decementation.

MATERIALS AND METHODS

Electronic and manual searches were performed for randomized clinical trials, prospective clinical trials, and prospective cohort studies that reported the technical failure rates of zirconia restorations. The Cochrane Collaboration risk-of-bias tool and Newcastle-Ottawa scale were used to assess the quality of the studies.

RESULTS

Fifty-two studies were included and most of them had unclear risk of bias. Considering all reported fractures/chipping, for veneered crowns with 1 to 3 years of follow-up, the relative risk (RR) of fracture in relation to loss or retention was 3.95 (95% CI 1.18-13.23; p = 0.03). For 4 to 6 years of follow-up, the RR was 5.44 (95% CI 1.41-20.92; p = 0.01). For veneered FPDs with 1 to 3 years of follow-up, the RR was 5.98 (95% CI 2.31-15.01; p = 0.0002). For 4 to 6 years of follow-up, the RR was 3.70 (95% CI 1.63-8.41; p = 0.002). For 7 years or more of follow-up, the RR was 3.45 (95% CI 1.84-6.46; p = 0.0001). When only framework fractures were considered, there were no significant differences for the RR in all follow-up periods (p > 0.05).

CONCLUSIONS

Higher RR for fracture/chipping in relation to decementation for veneered zirconia crowns and FPDs at all follow-up times. For framework fractures, no difference was observed between the risk of failure of the restoration due to fracture or decementation.

CLINICAL RELEVANCE

Zirconia crowns and FPDs showed relatively high success and survival rates. However, considering the technical failures, there is approximately four times higher chance of fracture/chipping than loss of retention for both single and multi-unit tooth-supported veneered zirconia restorations.

Surface Roughness and Bond Strength of Resin Composite to Additively Manufactured Zirconia with Different Porosities

PURPOSE

To investigate the bond strength of resin cement to additively manufactured (AM) zirconia with different porosities when compared to milled zirconia.

MATERIALS AND METHODS

A 12 × 5 mm disk virtual design file was used to fabricate a total of 48 disks divided into 4 groups: 3 groups were AM with different porosities including 0%-porosity (AMZ0 group), 20%-porosity (AMZ20 group), and 40%-porosity (AMZ40 group), and 1 milled zirconia (control or CNCZ group). The dimensions of all specimens were measured using a digital caliper. A 3D- confocal laser scanner was used to analyze surface morphology and measure the surface roughness (Sa), followed by SEM analysis. Tensile bond strength of composite resin cement to specimens was measured before and after aging procedures using a universal testing machine (n = 10). Failure modes were evaluated under a light microscope. Volumetric change data was analyzed using one-way ANOVA, and two-way ANOVA was used to compare bond strength values (α = 0.05).

RESULTS

There was a significant difference in volumetric changes among the groups. The CNCZ group showed the least changes in diameter 0.027 ± 0.029 mm and thickness 0.030 ± 0.012 mm and AM zirconia with 40% porosity showed the most volumetric changes in diameter 5.237 ± 0.023 mm. ANOVA test indicated an overall significant difference in surface roughness across all groups (F = 242.6, p < 0.001). The CNCZ group showed the highest mean Sa of 1.649 ± 0.240 µm, followed by AMZ40 group with Sa of 0.830 ± 0.063 µm, AMZ20 group with Sa of 0.780 ± 0.070 µm, and the AMZ0 group with Sa of 0.612 ± 0.063 µm. Two-way ANOVA showed significant difference in bond strength between the CNCZ group 12.109 ± 3.223 MPa and the AMZ0 group 8.629 ± 0.914 MPa, with significant pretest failures in specimens with porosities. Thermal cycling methods reduced the bond strength non-significantly in CNCZ group with no effect in the AMZ0 group.

CONCLUSION

Milled zirconia had a higher surface roughness and bond strength to composite resin cement than AM zirconia, and porosities in AM zirconia decreased the bond strength with significant pretest failures.

Revolution of Current Dental Zirconia: A Comprehensive Review

The aim of this article is to comprehensively review the revolution of dental zirconia (Zir), including its types, properties, applications, and cementation procedures. A comprehensive search of PubMed and Embase was conducted. The search was limited to manuscripts published in English. The final search was conducted in October 2021. Newly developed monolithic Zir ceramics have substantially enhanced esthetics and translucency. However, this material must be further studied in vitro and in vivo to determine its long-term ability to maintain its exceptional properties. According to the literature, monolithic translucent Zir has had promising results and a high survival rate. Thus, the utilization of this material is indicated when strength and esthetics are needed. Both the materials and methods used for cementation of monolithic Zir have significantly improved, encouraging dentists to use this material, especially when a conservative approach is required. Zir restorations showed promising outcomes, particularly for monolithic Zir crowns supported with implant and fixed dental prostheses.

Effect of Different Preparation Depths for an Inlay-Retained Fixed Partial Denture on the Accuracy of Different Intraoral Scanners: An In Vitro Study

PURPOSE

The aim was to evaluate the effect of different preparation depths for inlay-retained fixed partial dentures on the accuracy of intraoral scanners.

MATERIALS AND METHODS

Tooth preparations for two inlay-retained fixed partial dentures were done and divided according to depth of the preparation. Group A: 2mm pulpal floor depth, 3mm gingival floor depth and Group B: 3mm pulpal floor depth, 4mm gingival floor depth. The CEREC Omnicam4.4.4, Omnicam4.6.2. Trios3 and Medit i500 intraoral scanners were used in this study. Tooth preparations were scanned by each scanner 10 times. The STL files obtained from the intraoral scanners were compared to the reference models (trueness) and within each test group (precision) using a 3D comparison software. Data were then statistically analyzed.

RESULTS

Regarding trueness, two-way ANOVA revealed significant differences between the different types of scanners (p<0.001) (Omnicam4.4.4: 65.09 ±2.87 Omnicam4.6.1: 52.73 ±3.31 Medit i500: 58.45 ±2.63 Trios 3: 41.79 ±4.42). Preparation depth had no significant influence on the trueness (p = 0.083). For precision two-way ANOVA revealed significant differences between the different types of scanners (p<0.001). Preparation depth had no significant influence on the precision (p = 0.111). Statistically significant interactions were found between the different variables.

CONCLUSIONS

The depth of preparation did not have an influence on the accuracy of different scanners. However, the type of scanner influenced the accuracy of digital impressions with Trios3 showing the highest accuracy. This article is protected by copyright. All rights reserved.

Retention of posterior resin bonded fixed dental prostheses with different designs after chewing simulation

The aim of this study was to evaluate the effect of different preparation and framework designs on the retention of posterior resin bonded fixed dental prostheses (RBFDPs) made from monolithic zirconia ceramic. Forty-eight caries-free upper premolars and forty-eight upper third molars were used in this study. The teeth were randomly divided into six main groups (n = 8 each) according to the preparation design of two-retainer RBFDPs: narrow or wide rest, combined with 0, 1 or 2 retainer wings. All RBFDPs were milled from monolithic zirconia (KATANA Zirconia ML). They were bonded using Panavia V5 with its corresponding primer, and underwent thermodynamic loading (98 N, 1,200,000 cycles). Retention was evaluated for the surviving RBFDPs in a universal testing machine by means of a debonding test. Failure modes were evaluated using a light microscope. Data was statistically analyzed by Kruskal-Shapiro-Wilk followed by Mann-Whitney with Bonferroni correction for multiple testing. The survival rates after the chewing simulation were 75% (group narrow rest/no retainer wing), 62.5% (group wide rest/no retainer wing) and 100% (the other groups). The mean retention ranged from 31 N to 766 N. Designs with two retainer wings showed significantly higher bond strength than the other designs (p ≤ 0.05). The rest width did not show a significant effect on the retention. Posterior RBFDPs with a modified design (occlusal rest and two retainer wings) exhibited promising durability and retention. Designs with two additional retainer wings should be preferred over designs with one or no retainer wing, irrespectively of the rest width.

Long-term clinical performance and complications of zirconia-based tooth- and implant-supported fixed prosthodontic restorations: A summary of systematic reviews

OBJECTIVES

To present an overview on systematic reviews on prosthodontic zirconia restorations and to discuss long-term complications as well as information on anatomical and functional changes to the masticatory system.

DATA/SOURCES

MEDLINE, EMBASE, Trip medical, and Cochrane Library databases were searched for systematic reviews up to February 2021. Bias was assessed and clinical survival and complications were analyzed.

STUDY SELECTION

38 eligible articles published between 2006 and 2021 were included. The reviews were based on 128 in vivo studies on approximately 10,000 zirconia restorations. 5-year cumulative survival rates varied between 91.2% and 95.9% for tooth-supported (TS) single crowns (SC), 89.4% and 100% for TS multi-unit fixed dental prostheses (FDP), 97.1% and 97.6% for implant-supported (IS) SCs and 93.0% and 100% for IS FDPs. Chipping was the most often technical complication, followed by framework fracture, loss of retention, marginal discrepancies/discoloration, occlusal roughness and abutment/screw loosening. Color mismatch was the only esthetic complication. Biological complications were caries, endodontic complications, tooth fracture, periodontal disease, abrasion/attrition, persisting pain, high sensitivity, peri‑implantitis and soft tissue issues. Patients with bruxism were only examined sporadically.

CONCLUSIONS

5-year results for zirconia restorations were satisfactory. The predominant technical problem of veneering fractures could be overcome with adapted design or fabrication and application of monolithic restorations, but reviews of clinical studies on this subject are rare. The impact of zirconia restorations on the masticatory system remains unclear.

CLINICAL SIGNIFICANCE

Zirconia restorations are experiencing a rapidly increasing use in dental practice. Being highly wear-resistant, hard and durable, it can be assumed that they do not follow natural abrasion and changes in the masticatory system. Possible long-term effects on the stomatognathic system as a whole should therefore be considered.

Clinical Performance of Posterior Inlay-Retained and Wing-Retained Monolithic Zirconia Resin-Bonded Fixed Partial Dentures: Stage One Results of a Randomized Controlled Trial

PURPOSE

To prospectively compare the clinical performance of posterior inlay-retained and wing-retained monolithic zirconia fixed partial dentures (FPDs).

MATERIALS AND METHODS

After simple randomization, 30 participants received either one inlay-retained (n = 15; mean age: 56.38 ± 12.70 years; 10 men [66.7%]) or one wing-retained (n = 15; mean age: 45.90 ±13.24 years; 7 men [46.7%]) FPD. The restorations, which predominantly replaced first molars, were fabricated from translucent, 3 mol% yttria-stabilized zirconia and attached with self-etching resin cement. Restorations and abutment teeth were clinically followed up for complications one week and 3, 6, and 12 months after cementation. Plaque and gingival scores, probing pocket depths, and attachment levels were recorded for the abutment and contralateral reference teeth both before treatment and during follow-up examinations. The restorations were also assessed in accordance with FDI World Dental Federation criteria. Statistical analyses were conducted with R (α = 0.05). An adaptive, 2-stage study design based on the incidence of failure-free survival in the groups after 12 months (stage 1) was implemented. Predefined decision rules were used to determine whether further recruitment (stage 2) would enable the detection of a statistically significant difference between the restoration designs with sufficient power.

RESULTS

During 12 months, only one wing retainer debonded which required removal of the FPD. Failure-free survival was thus 93.3% for wing-retained and 100% for inlay-retained FPDs (log-rank test, p = 0.317). Moderate aftercare resulted in intervention-free rates of 78.8% and 86.7% for inlay-retained and wing-retained restorations, respectively (log-rank test, p = 0.605). Based on FDI World Dental Federation criteria, all restorations were acceptable at the 12-month follow-up (Fisher-Boschloo test, p = 0.161). Plaque, gingival, and periodontal scores remained practically unchanged from before treatment to the 12-month follow-up. Recruitment was stopped after stage 1 because, based on the small difference in the incidence of failure-free survival in the groups, it was accepted that it would not be possible to recruit the necessary number of participants to show a statistically significant difference between the retainer designs.

CONCLUSIONS

Both inlay-retained and wing-retained monolithic zirconia resin-bonded FPDs performed well for the 12-month, short-term follow-up period.

Monolithic Zirconia: An Update to Current Knowledge. Optical Properties, Wear, and Clinical Performance

The purpose of this paper was to update the knowledge concerning the wear, translucency, as well as clinical performance of monolithic zirconia ceramics, aiming at highlighting their advantages and weaknesses through data presented in recent literature. New ultra-translucent and multicolor monolithic zirconia ceramics present considerably improved aesthetics and translucency, which, according to the literature reviewed, is similar to those of the more translucent lithium disilicate ceramics. A profound advantage is their high strength at thin geometries preserving their mechanical integrity. Based on the reviewed articles, monolithic zirconia ceramics cause minimal wear of antagonists, especially if appropriately polished, although no evidence still exists regarding the ultra-translucent compositions. Concerning the survival of monolithic zirconia restorations, the present review demonstrates the findings of the existing short-term studies, which reveal promising results after evaluating their performance for up to 5 or 7 years. Although a significant increase in translucency has been achieved, new translucent monolithic zirconia ceramics have to be further evaluated both in vitro and in vivo for their long-term potential to preserve their outstanding properties. Due to limited studies evaluating the wear properties of ultra-translucent material, no sound conclusions can be made, whereas well-designed clinical studies are urgently needed to enlighten issues of prognosis and long-term survival.

Adhesion to Zirconia: A Systematic Review of Current Conditioning Methods and Bonding Materials

Background. Reliable bonding between resin composite cements and high strength ceramics is difficult to achieve because of their chemical inertness and lack of silica content that makes etching impossible. The purpose of this review is to classify and analyze the existing methods and materials suggested to improve the adhesion of zirconia to dental substrate by using composite resins, in order to explore current trends in surface conditioning methods with predictable results. Methods. The current literature, examining the bond strength of zirconia ceramics, and including in vitro studies, clinical studies, and a systematic review, was analyzed. The research in the literature was carried out using PubMed and Cochrane Library databases, only papers in English, published online from 2013 to 2018. The following keywords and their combinations were used: Zirconia, 3Y-TZP, Adhesion, Adhesive cementation, Bonding, Resin, Composite resin, Composite material, Dentin, Enamel. Results. Research, in PubMed and Cochrane Library databases, provided 390 titles with abstracts. From these, a total of 93 publications were chosen for analysis. After a full text evaluation, seven articles were discarded. Therefore, the final sample was 86, including in vitro, clinical studies, and one systematic review. Various adhesive techniques with different testing methods were examined. Conclusions. Airborne-particle abrasion and tribo-chemical silica coating are the pre-treatment methods with more evidence in the literature. Increased adhesion could be expected after physico-chemical conditioning of zirconia. Surface contamination has a negative effect on adhesion. There is no evidence to support a universal adhesion protocol.

Fifteen-year outcome of posterior all-ceramic inlay-retained fixed dental prostheses

OBJECTIVES

To evaluate the long-term clinical outcome of inlay-retained fixed dental prostheses (IRFDPs) made from lithium-disilicate glass-ceramic.

MATERIAL AND METHODS

Forty-five IRFDPs were placed in 42 patients (21 women, mean age 36.1 years and 21 men, mean age 42.0 years). The IRFDPs replaced 4 premolars and 19 first molars in the maxilla and 4 premolars and 18 first molars in the mandible. All teeth were prepared following a standardized protocol for ceramic inlay restorations. Five of the 45 FDPs were hybrid-retained restorations, i.e. one abutment tooth with an inlay retainer and one with a full crown retainer. All restorations were fabricated from heat-pressed lithium-disilicate ceramic (IPS e.max Press, Ivoclar Vivadent AG). The minimal size of the proximal connector was 16 mm² (4 mm × 4 mm in height and width) with a minimum occlusal ceramic thickness of 1.5 mm. Hydrofluoric acid etching (5%) and silane application was used for conditioning the bonding surfaces. Standard adhesive luting techniques were performed using a dentin adhesive and a resin composite. Standardized follow-up reports were performed annually. The survival rates were performed using the Kaplan-Meier analysis.

RESULTS

The mean observation period was 100 months (minimum 4, maximum 234 months). Thirty-three FDPs (73%) failed during the observation period and had to be replaced by other restorations. The Kaplan-Meier survival rate for IRFDPs was 57% after 5 years, 38% after 8 years and 22% after 15 years, while for hybrid-retained FDPs it was 100% after 5 years, 60% after 8 years and also 60% after 15 years.

CONCLUSION

With the design used in the current, study lithium-disilicate ceramic IRFDP had a high clinical failure rate and cannot be recommended for regular clinical use.

Do thermal treatments affect the mechanical behavior of porcelain-veneered zirconia? A systematic review and meta-analysis

OBJECTIVES

A systematic review of in vitro studies was conducted to assess the effect of thermal treatments on flexural strength or critical load to failure of porcelain-veneered zirconia (PVZ).

SOURCES

Literature searches were performed up to June 2018 in PubMed/MEDLINE, Scopus and Web of Science databases, with no publication year or language limits.

DATA

From 393 relevant studies, 21 were selected for full-text analysis, from which 7 failed to meet the inclusion criteria. The 14 remaining papers were included in the systematic review: 8 for meta-analysis and 6 restricted to descriptive analyses. Hand searching of reference lists resulted in no additional papers.

STUDY SELECTION

In vitro studies using PVZ specimens testing the influence of thermal treatments on the fracture resistance to monotonic or cyclic loading. Papers evaluating cooling rate were divided into those applying fast cooling from above the porcelain glass transition temperature (T_g), or from below it. Meta-analyses were performed separately for flexural strength and critical load to failure, using random effects at a 5% significance level.

CONCLUSIONS

Delaying furnace opening at a temperature below the porcelain T_g is advised for PVZ restorations, in order to improve their fracture resistance. Additional information is required to confirm the apparent beneficial effect of self-glaze and repeated veneer firings on the mechanical properties of these restorations. Finally, in order to obtain conclusive and relevant evidence regarding thermal treatments and the fracture resistance of PVZs, future studies should concentrate on anatomically-correct crown specimens.

Effect of different surface treatments and retainer designs on the retention of posterior Pd-Ag porcelain-fused-to-metal resin-bonded fixed partial dentures

The aim of this study was to investigate the adhesive property of palladium-silver alloy (Pd-Ag) and the simulated clinical performance of Pd-Ag porcelain-fused-to-metal (PFM), resin-bonded, fixed partial dentures (RBFPDs). A total of 40 Pd-Ag discs (diameter=5 mm) were prepared and divided into the following four groups (n=10): a) No sandblasting, used as a control; and b, 50 µm; c, 110 µm; and d, 250 µm aluminum oxide (Al₂O₃) particles, respectively. Another 50 discs were pre-sandblasted and divided into five groups (n=10) subjected to different treatments: e) Sandblasting, used as a control; f) silane; g) alloy primer; h) silica coating + silane and i) silica coating + alloy primer. All 90 discs were bonded to enamel with Panavia F 2.0 and then subjected to shear bond strength (SBS) testing. The fracture surfaces were examined by scanning electron microscopy. Next, 40 missing maxillary second premolar models were restored with one of the four following RBFPD designs (n=10): I) A premolar occlusal bar combined with molar double rests (MDR); II) both occlusal bars with a wing (OBB); III) a premolar occlusal bar combined with a molar dental band (MDB); and IV) two single rests adjacent to the edentulous space with a wing (SRB) used as a control. All specimens were aged with thermal cycling and mechanical loading. Subsequently, they were loaded until broken. The data were analyzed by one-way analysis of variance. Al₂O₃ (250 µm) abrasion provided the highest SBS (P<0.05). The alloy primer and silica + silane exhibited increased SBS. Furthermore, fracture analysis revealed that the failure mode varied among the different treatments. Whereas MDB exhibited the highest retention (P<0.05), that of OBB was greater than that of MDR (P<0.05), and the control exhibited the lowest retention. Abrasion with Al₂O₃ (250 µm) effectively increased the adhesive property of Pd-Ag. Additionally, treatment with the alloy primer and silica coating + silane was able to increase the adhesive property of abraded Pd-Ag. Under the present conditions, all three modified retainer types provided improved outcomes for Pd-Ag PFM RBFPDs compared with the control.

Effects of small-grit grinding and glazing on mechanical behaviors and ageing resistance of a super-translucent dental zirconia

OBJECTIVES

The purpose of this study is to elucidate the effects of small-grit grinding on the mechanical behaviors and ageing resistance of a super-translucent dental zirconia and to investigate the necessity of glazing for the small-grit ground zirconia.

METHODS

Small-grit grinding was performed using two kinds of silicon carbide abrasive papers. The control group received no grinding. The unground surfaces and the ground surfaces were glazed by an experienced dental technician. Finally, the zirconia materials were thermally aged in water at 134°C for 5h. After aforementioned treatments, we observed the surface topography and the microstructures, and measured the extent of monoclinic phase, the nano-hardness and nano-modulus of the possible transformed zone and the flexural strength.

RESULTS

Small-grit grinding changed the surface topography. The zirconia microstructure did not change obviously after surface treatments and thermal ageing; however, the glaze in contact with zirconia showed cracks after thermal ageing. Small-grit grinding did not induce a phase transformation but improved the flexural strength and ageing resistance. Glazing prevented zirconia from thermal ageing but severely diminished the flexural strength. The nano-hardness and nano-modulus of the surface layer were increased by ultrafine grinding.

CONCLUSIONS

The results suggest that small-grit grinding is beneficial to the strength and ageing resistance of the super-translucent dental zirconia; however, glazing is not necessary and even impairs the strength for the super-translucent dental zirconia.

CLINICAL SIGNIFICANCE

This study is helpful to the researches about dental grinding tools and maybe useful for dentists to choose reasonable zirconia surface treatments.

The Effect of Resin Bonding on Long-Term Success of High-Strength Ceramics

Digital manufacturing, all-ceramics, and adhesive dentistry are currently the trendiest topics in clinical restorative dentistry. Tooth- and implant-supported fixed restorations from computer-aided design (CAD)/computer-aided manufacturing (CAM)-fabricated high-strength ceramics-namely, alumina and zirconia-are widely accepted as reliable alternatives to traditional metal-ceramic restorations. Most recent developments have focused on high-translucent monolithic full-contour zirconia restorations, which have become extremely popular in a short period of time, due to physical strength, CAD/CAM fabrication, and low cost. However, questions about proper resin bonding protocols have emerged, as they are critical for clinical success of brittle ceramics and treatment options that rely on adhesive bonds, specifically resin-bonded fixed dental prostheses or partial-coverage restorations such as inlays/onlays and veneers. Resin bonding has long been the gold standard for retention and reinforcement of low- to medium-strength silica-based ceramics but requires multiple pretreatment steps of the bonding surfaces, increasing complexity, and technique sensitivity compared to conventional cementation. Here, we critically review and discuss the evidence on resin bonding related to long-term clinical outcomes of tooth- and implant-supported high-strength ceramic restorations. Based on a targeted literature search, clinical long-term studies indicate that porcelain-veneered alumina or zirconia full-coverage crowns and fixed dental prostheses have high long-term survival rates when inserted with conventional cements. However, most of the selected studies recommend resin bonding and suggest even greater success with composite resins or self-adhesive resin cements, especially for implant-supported restorations. High-strength ceramic resin-bonded fixed dental prostheses have high long-term clinical success rates, especially when designed as a cantilever with only 1 retainer. Proper pretreatment of the bonding surfaces and application of primers or composite resins that contain special adhesive monomers are necessary. To date, there are no clinical long-term data on resin bonding of partial-coverage high-strength ceramic or monolithic zirconia restorations.

Clinical prospective evaluation of zirconia-based three-unit posterior fixed dental prostheses: Up-to ten-year results

OBJECTIVES

Only a few studies exist, which assess the clinical long-term behavior of all-ceramic FDPs in the posterior region. The aim of the present prospective clinical study was to evaluate the clinical performance of posterior three-unit FDPs manufactured from Y-TZP after a service period up to 10 years.

METHODS

55 patients received 59 three-unit FDPs in the posterior region of the maxilla or mandible. Abutment teeth were prepared and full-arch impressions were taken. Definitive casts were fabricated and optically scanned. Frameworks were fabricated with computer-aided design (CAD) and manufacturing (CAM) technology. Y-TZP frameworks were veneered and adhesively luted to the abutment teeth. Baseline and follow-up examinations (service time: ≥ 48 months) were recorded by applying modified United States Public Health Services (USPHS) rating criteria. Cumulative survival rate was analyzed with Kaplan-Meier. Percentage of biological and technical complication was calculated.

RESULTS

Fifty-three patients with 57 FDPs attended the last follow-up visit and a mean observation period of the remaining was 6.3 ± 1.9 years was calculated. Biological complications occurred in 17.5%, technical complications in 28% of the FDPs. The 10-year cumulative survival rate amounted 85.0%. Three FDPs failed to survive, two due to a root fracture of the abutment tooth and one due to secondary caries.

CONCLUSIONS

Three-unit FDPs made from Y-TZP, veneered with ceramic offer a treatment option with a high rate of chipping. However, the manufacturing processes nowadays are modified in order to avoid this complication.

CLINICAL SIGNIFICANCE

The results of the present investigation suggest that three-unit Y-TZP posterior FDPs may are a possible treatment option. However, a high rate of chipping can be expected.