Wastewater reuse in a cascade based system of a petrochemical industry for the replacement of losses in cooling towers

Cultivating photosynthetic microorganisms in cooling water waste and urban effluents as a strategy of water regeneration and valorization

Contaminants from cooling water waste (CWW) generated by industries represent an environmental hazard if discharged into aquatic bodies and soil without treatment. Most treatment strategies are energy-demanding and costly; hence, low-cost and sustainable treatment alternative technologies are needed. The present study proposed cyanobacteria culture as a low-cost biological method to treat cooling water waste (CWW) while simultaneously producing carbohydrates. For this purpose, CWW from a cooling tower was evaluated in different dilutions with domestic wastewater (DW) (DW25% -CWW75%, DW50% -CWW50%, DW25% -CWW75%, DW100%, and CWW100%) (v/v). The CWW provided a high content of inorganic carbon and low content of N and P, which resulted in a high C/N ratio promoting a fast carbohydrate accumulation but low biomass production. In contrast, cultures with higher DW concentrations achieved similar results in 14 days. The best results were obtained with DW25% -CWW75%, achieving up to 52 ± 18% carbohydrate content on day 8, with the highest biomass concentration of 1.7 ± 0.12 g L-1 on day 14. This culture removed >94% of TAN, N-NO3- and P-PO43-, and 84 ± 10.82% of COD. This strategy could be a promising approach to treating CWW and DW from the same industry and producing value-added products and bioenergy.

The Removal of Selected Inorganics from Municipal Membrane Bioreactor Wastewater Using UF/NF/RO Membranes for Water Reuse Application: A Pilot-Scale Study

Membrane technology has advanced substantially as a preferred choice for the exclusion of widespread pollutants for reclaiming water from various treatment effluent. Currently, little information is available about Ultrafiltration (UF)/Nanofiltration (NF)/Reverse Osmosis (RO) performance at a pilot scale as a practical engineering application. In this study, the effluent from a full-scale membrane bioreactor (MBR) municipal wastewater treatment works (MWWTWs) was treated with an RO pilot plant. The aim was to evaluate the effect of operating conditions in the removal of selected inorganics as a potential indirect water reuse application. The influent pH, flux, and membrane recovery were the operating conditions varied to measure its influence on the rejection rate. MBR/RO exhibited excellent removal rates (>90%) for all selected inorganics and met the standard requirements for reuse in cooling and irrigation system applications. The UF and NF reduction of inorganics was shown to be limited to meet water standards for some of the reuse applications due to the high Electron Conductivity (EC > 250 μS·cm⁻¹) levels. The MBR/NF was irrigation and cooling system compliant, while for the MBR/UF, only the cooling system was compliant.

Prioritizing potential use of urban treated wastewater using expert-oriented and multi-criteria decision-making approaches: a case study in Iran

Allocating effluent of wastewater treatment plants to users of economic sectors and satisfying their requirements has created a challenging debate and a need for prioritization. This study assesses the importance of sectors that utilize treated wastewater (TWW) using risk and social acceptability indexes based on expert-oriented approaches. Considered sectors are agriculture, industry, urban green space and natural resources and the study area is located in Iran, around the Isfahan North Wastewater Treatment Plant. The risk index is calculated using Frank and Morgan model and consequently TWW use in the industrial sector is less dangerous than other sectors. Moreover, the social acceptability index, which was determined using Mamdani fuzzy inference set, indicates higher acceptability of TWW use in natural resources sector compared with other sectors. By constructing the conceptual model, generating the decision matrix and using the results of gray relational analysis decision-making model for the four sectors, the allocation priorities of TWW became industry, natural resource, green space, and agriculture respectively. It is suggested that Water and Wastewater Company grant permission for TWW use to water-consuming industries and man-made forests development, which result in increasing employment, reduction of harmful effects of dust, and water consumption decrease.

Water reuse: An alternative to minimize the environmental impact on the leather industry

Tanneries are industries that may cause high environmental impact. Consequently, they are responsible for generating a large amount of wastewater with high concentrations of contaminants that require significant investment and operating costs in their treatment in order to accomplish the emission standards required by environmental legislation. This work has as main objective to minimize the environmental impact of the water used by tanneries through the study of reuse possibilities of wastewater tanning floats. The major concern is related to the pollutant chromium in the environment, since it is the tanning product that gives the best characteristics to leather and consequently the most used product. The reuse tests were performed on pilot and industrial scales. During the experiments, the following process control parameters were evaluated: pH, density, acid-base indicators for hide and shrinkage temperature. To validate the water reuse in tanneries, samples of wet-blue leather and residual floats were collected from pilot and industrial processes to perform chemical analyses to prove the validity of the process with reuse. Research has shown that reuse techniques, when properly evaluated, can be used in industries. In addition to reducing water demand, the reuse of wastewater in tanning processes minimizes the disposal of the wastewater with chromium and uses the residual chromium float.

Feasible analysis of reusing flowback produced water in the operational performances of oil reservoirs

Water reuse is considered one of the most efficient and optimum ways in petroleum industries to address the water scarcity problem. The effluents which are made by the petroleum operations are supposed to be one of the hazardous materials when they are discharged to the environment. The objective of this study is to measure the volume of the required water for the operational performances of the studied oil field. To do this, the necessary water and the volume of provided treated water for the waterflooding, tertiary flooding, and hydraulic fracturing procedures are appropriately measured and by the utilization of photo-Fenton/flotation are administered to remove the oil droplets. According to the observational measurements, it is clarified that hydraulic fracturing has supplied approximately 93% of its required water by the treatment of flowback water and it virtually eliminated the necessity of fresh water from local or domestic water resources. Moreover, the total freshwater that has been saved in this oil field is investigated about 80% of the total required water for their performances. Consequently, the lower need of fresh water from local resources would reduce the unnecessary expenses to provide this volume of water and would save fresh water for about 2750 inhabitants for 1 year to overcome the issue of water scarcity in the world.