Analyzing the adsorptive behavior of Amoxicillin on four Zr-MOFs nanoparticles: Functional groups dependence of adsorption performance and mechanisms

Tuning the mechanical properties of sol-gel monolithic metal-organic frameworks by ligand engineering

The sol-gel monolithic MOFs has come to prominent attention for industrial application owing to the higher powder packing density, enhanced processabilities and mechanical stabilities compared to the powder counterpart. The mechanical properties are particularly important during machine shaping processing because of porous framework structure. We used ligand engineering to design and synthesize monoUiO-66-type materials modified different chemical functional groups (-NH2, -2OH, -2COOH) by sol-gel method, with the aim to assess the impact of different functional groups on the mechanical properties of these monolithic materials based on nanoindentation technology. We observe larger mass and sterically bulky functional groups (-2COOH) can significantly decrease the BET areas and pore volume of monoUiO-66 through N2 adsorption isotherms at 77 K. Hence, the two -COOH groups modified monoUiO-66 tends to exhibit the higher H of 0.589 ± 0.018 GPa and E of 15.471 ± 0.250 GPa compared with monoUiO-66 modified with -NH2 (0.334 ± 0.009 GPa/11.959 ± 0.243 GPa) and -2OH (0.331 ± 0.008 GPa/10.251 ± 0.142 GPa) groups. The creep indentation tests and the jump indentation tests further demonstrate the modification by larger functional groups -COOH on monoUiO-66 could resist irreversible plastic deformation. Furthermore, the monoUiO-66-(COOH)2 has significantly smaller the activation volume of 0.34 ∼ 0.43 nm3, highlighting the introduction of -COOH groups reduced the pore volume and restrict the number of pores involved in one collapse event. Our results demonstrate the larger mass and sterically bulky functional groups have significant influence on the mechanical properties of the monoMOFs materials.

Effective adsorption of amoxicillin by using UIO-66@ Cr-MIL-101 nanohybrid: isotherm, kinetic, thermodynamic, and optimization by central composite design

In this research, the amoxicillin (AMX) removal was studied on a prepared nanosorbent from MOFs. The aim of this research work is to prepare nanohybrids based on metal-organic frameworks (MOFs) as an efficient nanosorbent for the absorption of amoxicillin drug. In this study, UIO-66 nanoparticles (UIO-66 NPs) were prepared from Zirconium (Zr) metal and 1,4-benzene dicarboxylic acid (BDC). Then UIO-66@Cr-MIL-101 nanohybrid was synthesized by hydrothermal method. Structural and physicochemical properties of nanohybrid UIO-66@Cr-MIL-101 were characterized by different analyses such as X-ray diffraction analysis (XRD), fourier transform infrared spectrometer (FT-IR), scanning electron microscopy (SEM), energy dispersive X-ray (EDX), transmission electron microscopy (TEM), therapeutic goods administration (TGA), and Brunauer-Emmett-Teller (BET). The effect of four fundamental variables effective on adsorption was optimized by the central composite response surface methodology (CCRSM). This parameters including loading percentage of Cr-MIL-101 NPs (10-30%), initial concentration of AMX (20-140 mg L-1), contact time (20-60 min), and pH (20-10). The removal percentage (Re%) of AMX equal to 99.50% was obtained under the following conditions: The loading value of 20% Wt%, the initial concentration of AMX 80 mg L-1, contact time 20 min, and pH = 6. Also, the experimental data were investigated with famous kinetic models and isotherms, and it was observed that AMX removal by nanohybrid is correlated with the PSO kinetic model and Langmuir isotherm.

Static adsorption and photocatalytic degradation of amoxicillin using titanium dioxide/hydroxyapatite nanoparticles based on sea scallop shells

The objective of this study is to investigate the efficiency of two processes for the amoxicillin removal through static (batch) adsorption and photocatalytic degradation onto the prepared samples. Three solid materials as photocatalyst and/or adsorbent were synthesized viz. nanotitanium dioxide (NT) prepared by the sol-gel method, scallop shells-based nanohydroxyapatite (NP), and nanotitanium dioxide/nanohydroxyapatite composite (NTP). The physicochemical and morphological properties of the prepared samples were tested by TGA, XRD, DRS, ATR-FTIR, nitrogen adsorption/desorption isotherm, zeta potential, SEM, and TEM. The major operational conditions were optimized for catalyst or adsorbent mass, pH, shaking time, initial amoxicillin (AMX) concentration, power of UV lamp, and temperature. The results illuminated that NTP achieved the highest adsorption capacity (88.46 mg/g) at 20 ℃ and AMX adsorption onto all the solid materials was well applied by Langmuir, Temkin, pseudo-second order, and Elovich models. The maximum desorption percent (98%) was attained by acetone. The degradation percent of AMX reached 85.3 and 99.5% for NT and NTP, respectively, using 0.9 g/L of catalyst dosage through 90 min. AMX photodegradation onto the catalysts' surface was well fitted by Langmuir-Hinshelwood, Arrhenius, and Eyring-Polanyi models with endothermic, physical, and nonspontaneous nature of photocatalysis process. NTP acts as a promising adsorbent and photocatalyst for the antibiotics' removal in wastewater.

Carbon Nanostructures-Silica Aerogel Composites for Adsorption of Organic Pollutants

Silica aerogels are a class of materials that can be tailored in terms of their final properties and surface chemistry. They can be synthesized with specific features to be used as adsorbents, resulting in improved performance for wastewater pollutants' removal. The purpose of this research was to investigate the effect of amino functionalization and the addition of carbon nanostructures to silica aerogels made from methyltrimethoxysilane (MTMS) on their removal capacities for various contaminants in aqueous solutions. The MTMS-based aerogels successfully removed various organic compounds and drugs, achieving adsorption capacities of 170 mg⋅g^-1 for toluene and 200 mg⋅g^-1 for xylene. For initial concentrations up to 50 mg⋅L^-1, removals greater than 71% were obtained for amoxicillin, and superior to 96% for naproxen. The addition of a co-precursor containing amine groups and/or carbon nanomaterials was proven to be a valuable tool in the development of new adsorbents by altering the aerogels' properties and enhancing their adsorption capacities. Therefore, this work demonstrates the potential of these materials as an alternative to industrial sorbents due to their high and fast removal efficiency, less than 60 min for the organic compounds, towards different types of pollutants.

Optimized Mo-doped IrOx anode for efficient degradation of refractory sulfadiazine

Electrochemical advanced oxidation processes (EAOPs) is considered to be an efficacious method to degrade antibiotics. However, the performance of the anode has become the main limiting factor of this technology. In this study, due to the electron-deficient characteristics and the improvement of OER performance of Mo, we chose to use thermal decomposition to incorporate Mo into IrO₂ to prepare anodes with industrial applicability. Under the optimal ratio of Ir to Mo is 7:3, (Ir_0.7Mo_0.3)O_x electrode's particular pore structure can expose more active sites and create a channel for the transportation of electrons, thereby promoting the formation of free radicals and degrading pollutants more efficiently. (Ir_0.7Mo_0.3)O_x electrode also has a higher mass activity (6.332 A g^-1, three times that of the IrO₂ electrode) and a larger electrochemical active area (ECSA, 375.43 cm², seven times that of the IrO₂ electrode). In addition, the optimal conditions of (Ir_0.7Mo_0.3)O_x electrode for degrading sulfadiazine(SDZ) were explored, which achieved a higher removal than traditional electrodes (90% removal within 4 h) when the Ti plate was the substrate. Through the intermediate products of SDZ degradation and related literatures, two possible degradation pathways of SDZ were speculated. This research provides a new type of anode catalyst for the degradation of sulfonamide antibiotics, which is possible for industrial application.

Total removal of amoxicillin from water using magnetic core nanoparticles functionalized with silver

Framed in the problem of emerging pollutants, in this work we introduce a novel procedure for the total removal of amoxicillin from water samples using magnetic nanoparticles functionalized with nanometric silver (Fe₃O₄@AgNPs). Experimental conditions such as pH, contact time, temperature, as well as adsorbate and adsorbent doses have been studied to achieve the total adsorption for different concentrations of amoxicillin in water. Particularly, for concentrations 10 and 100 mg L^-1, a maximum removal efficiency of 100% was reached at room temperature and pH = 7 after 15 min of contact time between adsorbent and water samples under gentle shaking. The doses of adsorbent employed to remove 10 and 100 mg L^-1 of amoxicillin were 100 and 500 μL, respectively. Characterization of the adsorbent surfaces was performed by Scanning and Transmission Electron Microscopy, Energy Dispersive X-ray Spectroscopy, BET analysis and Fourier-transform infrared spectroscopy. Recycling studies were carried out employing 500 μL of NaOH solution 1 M during 15 min in order to explore desorption and reuse of the adsorbent, showing that Fe₃O₄@AgNPs remains unaltered and can be used for two more additionally adsorption cycles, exhibiting 93% adsorption efficiency after the third regeneration. The characterization of equilibrium isotherms and thermodynamics reveal a Langmuir-type endothermic chemisorption.

Salt sealing induced in situ N-doped porous carbon derived from wheat bran for the removal of doxycycline from aqueous solution

In situ N-doped porous carbon (NPC) derived from wheat bran via a convenient salt sealing and air-assisted strategy was prepared for the removal of doxycycline (DOX) from aqueous solution. The NPC was precisely characterized by SEM, FTIR, XPS and BET analysis. Additionally, the experimental variables including contact time, adsorbent dosage of NPC and pH were optimized by using Box-Behnken design (BBD) under response surface methodology (RSM). The predicted adsorption capacity of DOX was found to be 291.14 mg g-1 under optimalizing experimental conditions of 196 min contact time, 0.2 g L-1 adsorbent dosage and pH 5.78. The adsorption experimental data fitted Langmuir, Koble-Corrigan and Redlich-Peterson models well, and the pseudo-second-order model perfectly described the DOX adsorption process onto NPC. Thermodynamic parameters of DOX adsorbed onto NPC indicated that the adsorption process was spontaneous and endothermic. Moreover, the adsorption of DOX on NPC was mostly controlled by electrostatic interaction, π-π electron-donator-acceptor (EDA) interaction, hydrogen-bonding and Lewis acid-base effect. Besides, the N element of NPC also played a role in capturing DOX. The maximum monolayer adsorption capacity of DOX was turn out to be 333.23 mg g-1 at 298 K, which suggested that the NPC could be a prospectively adsorbent for the removal of DOX from wastewater.

The potential application of bio-based ceramic/organic xerogel derived from the plant sources: A new green adsorbent for removal of antibiotics from pharmaceutical wastewater

A bio-based ceramic/organic xerogel (BCO-xerogel) was obtained from the combination of sugarcane bagasse ash, polyvinyl alcohol, and pine cone-derived tannin extract, which are abundant, non-toxic, and renewable sources. The as-prepared BCO-xerogel was used as a low-cost green adsorbent for the eliminate of four types of the most widely used antibiotics, including amoxicillin (AMX), tetracycline (TC), cefalexin (CLX), and penicillin G (PEN G) residuals from contaminated water. The simultaneous effects conventional variables including adsorbent dosage, antibiotic concentrations, solution pH, and contact time were studied and optimized by central composite design (CCD) under response surface methodology (RSM). Analysis of variance (ANOVA) was employed as a statistical formula to determine the significance of operating environmental conditions and their interactions with 95% confidence limits. Under optimized conditions, the experimental removal efficiencies for AMX, TC, CLX, and PEN G were 98.78 ± 3.25, 99.12 ± 2.52, 98.02 ± 1.98, and 98.42 ± 2.19, respectively. The adsorption isotherms and kinetics were better fitted with Langmuir and pseudo-second-order models, respectively. Thermodynamic studies showed that the adsorption process was endothermic, spontaneous, and occurred by combination of physical and chemical mechanisms. Also, evaluating the ability of BCO-xerogel to adsorptive removal of AMX, TC, CLX, and PEN G antibiotics in real wastewaters showed about 97.4-98.6% adsorption efficiency in river water and about 67.1-71.3% in three hospital effluents. After the adsorption process, the antibiotic-loaded adsorbent was regenerated by NaOH (0.01 mol L^-1), and the reusability tests showed that the removal efficiencies of the antibiotics in the four recovery steps were still above 90%. This work explored the development of green, efficient, and economical bio-adsorbent that can be utilized for the removal of antibiotics from contaminated wastewaters.

Recent advances in performance improvement of Metal-organic Frameworks to remove antibiotics: Mechanism and evaluation

Antibiotic pollution is a serious global problem, which may threaten the health of human and ecosystem. Thereinto, water pollution is the most common way. Thus, it is necessary to develop effective methods to remove antibiotics from the natural aqueous environments. Metal-organic Frameworks (MOFs) - based adsorption and photocatalysis strategies have been demonstrated to be efficient, environmental and promising methods to solve antibiotic pollution and repair the environment. In this review, several strategies to improve the properties of MOFs for removal were summarized and discussed. And the removal mechanisms were also discussed. Besides, new and more reliable evaluation methods of MOFs to remove antibiotics were presented, including preferential adsorption (q_p), quantum yields (QY), space time yields (SY) and figure of merit (FOM). This paper provides alternative perspectives for researchers to improve the properties of MOFs and raise analytic efficiency of antibiotic removal.

Accurate Removal of Toxic Organic Pollutants from Complex Water Matrices

Characteristic emerging pollutants at low concentration have raised much attention for causing a bottleneck in water remediation, especially in complex water matrices where high concentration of interferents coexist. In the future, tailored treatment methods are therefore of increasing significance for accurate removal of target pollutants in different water matrices. This critical review focuses on the overall strategies for accurately removing highly toxic emerging pollutants in the presence of typical interferents. The main difficulties hindering the improvement of selectivity in complex matrices are analyzed, implying that it is difficult to adopt a universal approach for multiple targets and water substrates. Selective methods based on assorted principles are proposed aiming to improve the anti-interference ability. Thus, typical approaches and fundamentals to achieve selectivity are subsequently summarized including their mechanism, superiority and inferior position, application scope, improvement method and the bottlenecks. The results show that different methods may be applicable to certain conditions and target pollutants. To better understand the mechanism of each selective method and further select the appropriate method, advanced methods for qualitative and quantitative characterization of selectivity are presented. The processes of adsorption, interaction, electron transfer, and bond breaking are discussed. Some comparable selective quantitative methods are helpful for promoting the development of related fields. The research framework of selectivity removal and its fundamentals are established. Presently, although continuous advances and remarkable achievements have been attained in the selective removal of characteristic organic pollutants, there are still various substantial challenges and opportunities. It is hopeful to inspire the researches on the new generation of water and wastewater treatment technology, which can selectively and preferentially treat characteristic pollutants, and establish a reliable research framework to lead the direction of environmental science.

Novel NbCo-MOF as an advanced peroxymonosulfate catalyst for organic pollutants removal: Growth, performance and mechanism study

Multivariate metal-organic frameworks (MTV-MOFs) are expected as catalyst to apply to the advanced oxidation processes (AOPs) based on sulfate radical (SO₄·^-) to treat wastewater containing organic pollutants. Mixing metals de novo method was combined with stringent solvothermal conditions to synthesize macaroon-like NbCo-MOF catalyst. NbCo-MOF catalyst prepared with different atom ratios and growth time presented various morphology, structure, performance, and distinctive MTV-MOFs growth law which were confirmed by SEM, TEM, EDS, XRD, FTIR, raman spectra and UV-vis spectra. Besides, optimum peroxymonosulfate (PMS) catalytic activation conditions were studied. Furthermore, the effects of anions (Cl^-, NO₃^-, HCO₃^-, and C₂O₄^2-) on NbCo-MOF catalytic activation were explored which were proved very limited. Particularly, the Co²⁺/Co³⁺ cycle combining with the Nb⁴⁺/Nb⁵⁺ cycle for PMS activation were verified by XPS. EPR and quenching experiment results indicated exists non-radical pathway (¹O₂), but radical pathways are dominant (SO₄·^- O₂·^-, and ·OH). Moreover, the TC removal rate exhibited no significant reduce after three times run. Furthermore, NbCo-MOF exhibited excellent decomposing ability towards methylene blue, tylosin tartrate, rhodamine B, and tetracycline with the removal rate reaching to 100%, 98.4%, 99.7%, and 99.7% in 30 min respectively and also maintained good performance in actual water environment.

A Comprehensive Insight on Adsorption of Polyaromatic Hydrocarbons, Chemical Oxygen Demand, Pharmaceuticals, and Chemical Dyes in Wastewaters Using Biowaste Carbonaceous Adsorbents

Recent trends in adsorption of hazardous organic pollutants including Polyaromatic Hydrocarbons (PAHs), Chemical Oxygen Demand (COD), Pharmaceuticals, and Chemical Dyes in wastewater using carbonaceous materials such as activated carbon (AC) and biochar (BC) have been discussed in this paper. Utilization of biomass waste in the preparation of AC and BC has gained a lot of attention recently. This review outlines the techniques used for preparation, modification, characterization, and application of the above-mentioned materials in batch studies. The approaches towards understanding the adsorption mechanisms have also been discussed. It is observed that in the majority of the studies, high removal efficiencies were reported using biowaste adsorbents. Regarding the full potential of adsorption, varying values were obtained that are strongly influenced by the adsorbent preparation technique and adsorption method. In addition, most of the studies were concentrated on the kinetic, isotherm equilibrium, and thermodynamic aspects of adsorption, suggesting the dominant isotherm and kinetic models as Langmuir or Freundlich and pseudo-second-order models. Due to development in biosorbents, adsorption has been found to be increasingly economical. However, application of these adsorbents at commercial scale has not been adequately investigated and needs to be studied. Most of the studies have been conducted on synthetic solutions that do not completely represent the discharged effluents. This also needs attention in future studies.

Strong adsorption properties and mechanism of action with regard to tetracycline adsorption of double-network polyvinyl alcohol-copper alginate gel beads

In the present study, glutaraldehyde was used as a hydrophobic modifier to crosslink polyvinyl alcohol (PVA), and copper ion was immobilized by sodium alginate (SA). Polyvinyl alcohol-copper alginate (PVA-CA) gel beads were prepared by a one-step process, and were used to adsorb and remove tetracycline (TC) from an aqueous solution. The beads were characterized by scanning electron microscopy (SEM), thermogravimetric analysis (TGA), Brunauer-Emmett-Teller (BET) measurement, X-ray diffraction (XRD), energy dispersive spectroscopy (EDS), and Fourier transform infrared spectroscopy (FTIR). The adsorption experiment showed that the optimal pH value of the beads was 5, and that their adsorption met pseudo-second-order kinetic and Langmuir isothermal models. The adsorption thermodynamics experiment showed that the adsorption process was spontaneous and endothermic. Under optimal adsorption conditions, the maximum adsorption capacity for TC of the beads was 231.431 mg/g, which was much higher than that of a single copper alginate matrix. After 5 adsorption-desorption cycles, the adsorption capacity remained high. FTIR and X-ray photoelectron spectroscopy (XPS) revealed that the cation bonding bridge reaction was the main driving force behind the adsorption mechanism. Compared with other reported adsorption materials, the PVA-CA gel beads have high adsorption capacity, a simple preparation process, and excellent recovery performance.

Study of the Cycloaddition of CO2 with Styrene Oxide Over Six-Connected spn Topology MOFs (Zr, Hf) at Room Temperature

A series of MOFs with a 6-connected spn topology were synthesized (MOF-808-(Zr, Hf), PCN-777-(Zr, Hf), MOF-818-(Zr, Hf)). Through the in situ DRIFTS of NH₃ adsorption-desorption, we found that the activated catalyst mainly contains Lewis acid sites. The effects of different organic ligands on the Lewis acid of the Zr₆ cluster were analyzed by XPS and NH₃ -TPD, and the relative Lewis acidity of the same metal was obtained: PCN-777>MOF-808>MOF-818. In the Py-FTIR results, we confirmed that MOF-818 has a higher acid site density. In the activity test, MOFs with mesoporous structure showed better catalytic activity under normal temperature and pressure. Among them, MOF-818 can still maintain a high degree of crystallinity after catalysis. Finally, we use density functional theory to propose the mechanism of the cycloaddition reaction of carbon dioxide and styrene oxide. The results show that the metal is coordinated with styrene oxide and halogens attack the β carbon of the epoxide.

Luminescent cellulose-based porous binary metal-organic gels in an adsorption bed for effective adsorption and sensitive detection of chlortetracycline hydrochloride

Three novel (Fe-Eu) JLUE-MOGs were successfully fabricated through a solvothermal method and employed to construct the double-effect system for antibiotics adsorption and detection. The characterizations highlighted the properties of ample active sites, large surface areas and hierarchical porous structures, which did contribute to superb and rapid chlortetracycline hydrochloride (CTC) adsorption by JLUE-MOGs. Besides, the effects of initial pH values, JLUE-MOG dosages and co-existing inorganic ions on the CTC adsorption could be explained by pore filling, π-π EDA interaction, electrostatic interaction, water affinity as well as hydrogen bonding. Moreover, the optimized condition was cross-explored by response surface methodology (RSM) with tiny differences compared to actual experiments. In addition, fluorescent JLUE-MOG-7 was implemented for sensitive recognition of CTC and reflecting adsorption processes. Furthermore, shaping JLUE-MOG-7@cellulose aerogels were fabricated as filter materials for applying into an adsorption bed. The breakthrough process was fitted well by Bohart-Adams model and Thomas model, along with recognizable fluorescence changes of immobilized adsorbents. This work develops efficient and luminescent powder-like JLUE-MOGs for antibiotics adsorptive enrichment and sensitive detection. More importantly, immobilized JLUE-MOG@cellulose aerogels, as promising and alternative adsorbents with real-time fluorescence changes, can be utilized for continuously pollutants removal in real wastewater treatment.