Comparative performance evaluation of multi-metal resistant fungal strains for simultaneous removal of multiple hazardous metals

Bioremoval of heavy metals from aqueous solution using dead biomass of indigenous fungi derived from fertilizer industry effluents: isotherm models evaluation and batch optimization

The present work investigated the utilization of dead biomass of the highly multi-heavy metals tolerant indigenous fungal strain NRCA8 isolated from the mycobiome of fertilizer industry effluents that containing multiple heavy metal ions at high levels to remove Pb2+, Ni2+, Zn2+, and Mn2+ as multiple solutes from multi-metals aqueous solutions for the first time. Based on morphotype, lipotype and genotype characteristics, NRCA8 was identified as Cladosporium sp. NRCA8. The optimal conditions for the bioremoval procedure in the batch system were pH 5.5 for maximum removal (91.30%, 43.25%, and 41.50%) of Pb2+, Zn2+ and Mn2+ but pH 6.0 supported the maximum bioremoval and uptake of Ni2+ (51.60% and 2.42 mg/g) by NRCA8 dead biomass from the multi-metals aqueous solution, respectively. The 30 min run time supported the highest removal efficiency and uptake capacity of all heavy metals under study. Moreover, the equilibrium between the sorbent NRCA8 fungal biomass and sorbates Ni2+, Pb2+ and Zn2+ was attained after increasing the dead biomass dose to 5.0 g/L. Dead NRCA8 biomass was described by scanning electron microscopy, energy-dispersive X-ray spectroscopy and Fourier transform infrared spectrometer before and after biosorption of Pb2+, Ni2+, Zn2+ and Mn2+ under multiple metals system. The Langmuir, Freundlich and Dubinin-Kaganer-Radushkevich isotherms were applied to characterize the adsorption equilibrium between Pb2+, Ni2+, Mn2+ and Zn2+ and the adsorbent NRCA8. By comparing the obtained coefficient of regression (R2) by Freundlich (0.997, 0.723, 0.999, and 0.917), Langmiur (0.974, 0.999, 0.974, and 0.911) and Dubinin-Radushkevich (0.9995, 0.756, 0.9996 and 0.900) isotherms values for Pb2+, Zn2+, Ni2+ and Mn2+ adsorption, respectively, it was found that the isotherms are proper in their own merits in characterization the possible of NRCA8 for removal of Pb2+, Zn2+, Ni2+ and Mn2+. DKR isotherm is the best for Pb2+ and Ni2+ (0.9995 and 0.9996) while Langmiur isotherm giving a good fit to the Zn2+ sorption (0.9990) as well as Freundlich isotherm giving a good fit to the Mn2+ sorption (0.9170). The efficiencies of Cladosporium sp. NRCA8 dead biomass for bioremoval of heavy metals from real wastewater under the optimized conditions were Pb2+, Ag+, Mn2+, Zn2+ and Al3+ ˃ Ni2+ ˃ Cr6+ ˃ Co2+ ˃ Fe3+ ˃ Cu2+ ˃ Cd2+. Dead NRCA8 biomass showed efficient ability to adsorb and reduce harmful components in the industrial effluents to a level acceptable for discharge into the environment.

Roles and significance of chelating agents for potentially toxic elements (PTEs) phytoremediation in soil: A review

Phytoremediation is a biological remediation technique known for low-cost technology and environmentally friendly approach, which employs plants to extract, stabilise, and transform various compounds, such as potentially toxic elements (PTEs), in the soil or water. Recent developments in utilising chelating agents soil remediation have led to a renewed interest in chelate-induced phytoremediation. This review article summarises the roles of various chelating agents and the mechanisms of chelate-induced phytoremediation. This paper also discusses the recent findings on the impacts of chelating agents on PTEs uptake and plant growth and development in phytoremediation. It was found that the chelating agents have increased the rate of metal absorption and translocation up to 45% from roots to the aboveground plant parts during PTEs phytoremediation. Besides, it was also explored that the plants may experience some phytotoxicity after adding chelating agents to the soil. However, due to the leaching potential of synthetic chelating agents, the use of organic chelants have been explored to be used in PTEs phytoremediation. Finally, this paper also presents comprehensive insights on the significance of using chelating agents through SWOT analysis to discuss the advantages and limitations of chelate-induced phytoremediation.

Insight Into the Molecular Mechanisms Underpinning the Mycoremediation of Multiple Metals by Proteomic Technique

We investigated the fungus Aspergillus fumigatus PD-18 responses when subjected to the multimetal combination (Total Cr, Cd2+, Cu2+, Ni2+, Pb2+, and Zn2+) in synthetic composite media. To understand how multimetal stress impacts fungal cells at the molecular level, the cellular response of A. fumigatus PD-18 to 30 mg/L multimetal stress (5 mg/L of each heavy metal) was determined by proteomics. The comparative fungal proteomics displayed the remarkable inherent intracellular and extracellular mechanism of metal resistance and tolerance potential of A. fumigatus PD-18. This study reported 2,238 proteins of which 434 proteins were exclusively expressed in multimetal extracts. The most predominant functional class expressed was for cellular processing and signaling. The type of proteins and the number of proteins that were upregulated due to various stress tolerance mechanisms were post-translational modification, protein turnover, and chaperones (42); translation, ribosomal structure, and biogenesis (60); and intracellular trafficking, secretion, and vesicular transport (18). In addition, free radical scavenging antioxidant proteins, such as superoxide dismutase, were upregulated upto 3.45-fold and transporter systems, such as protein transport (SEC31), upto 3.31-fold to combat the oxidative stress caused by the multiple metals. Also, protein–protein interaction network analysis revealed that cytochrome c oxidase and 60S ribosomal protein played key roles to detoxify the multimetal. To the best of our knowledge, this study of A. fumigatus PD-18 provides valuable insights toward the growing research in comprehending the metal microbe interactions in the presence of multimetal. This will facilitate in development of novel molecular markers for contaminant bioremediation.

Sustainable Application of Biosorption and Bioaccumulation of Persistent Pollutants in Wastewater Treatment: Current Practice

Persistent toxic substances including persistent organic pollutants and heavy metals have been released in high quantities in surface waters by industrial activities. Their presence in environmental compartments is causing harmful effects both on the environment and human health. It was shown that their removal from wastewaters using conventional methods and adsorbents is not always a sustainable process. In this circumstance, the use of microorganisms for pollutants uptake can be seen as being an environmentally-friendly and cost-effective strategy for the treatment of industrial effluents. However, in spite of their confirmed potential in the remediation of persistent pollutants, microorganisms are not yet applied at industrial scale. Thus, the current paper aims to synthesize and analyze the available data from literature to support the upscaling of microbial-based biosorption and bioaccumulation processes. The industrial sources of persistent pollutants, the microbial mechanisms for pollutant uptake and the significant results revealed so far in the scientific literature are identified and covered in this review. Moreover, the influence of different parameters affecting the performance of the discussed systems and also very important in designing of treatment processes are highly considered. The analysis performed in the paper offers an important perspective in making decisions for scaling-up and efficient operation, from the life cycle assessment point of view of wastewater microbial bioremediation. This is significant since the sustainability of the microbial-based remediation processes through standardized methodologies such as life cycle analysis (LCA), hasn’t been analyzed yet in the scientific literature.

Mycoremediation of heavy metals: processes, mechanisms, and affecting factors

Industrial processes and mining of coal and metal ores are generating a number of threats by polluting natural water bodies. Contamination of heavy metals (HMs) in water and soil is the most serious problem caused by industrial and mining processes and other anthropogenic activities. The available literature suggests that existing conventional technologies are costly and generated hazardous waste that necessitates disposal. So, there is a need for cheap and green approaches for the treatment of such contaminated wastewater. Bioremediation is considered a sustainable way where fungi seem to be good bioremediation agents to treat HM-polluted wastewater. Fungi have high adsorption and accumulation capacity of HMs and can be potentially utilized. The most important biomechanisms which are involved in HM tolerance and removal by fungi are bioaccumulation, bioadsorption, biosynthesis, biomineralisation, bioreduction, bio-oxidation, extracellular precipitation, intracellular precipitation, surface sorption, etc. which vary from species to species. However, the time, pH, temperature, concentration of HMs, the dose of fungal biomass, and shaking rate are the most influencing factors that affect the bioremediation of HMs and vary with characteristics of the fungi and nature of the HMs. In this review, we have discussed the application of fungi, involved tolerance and removal strategies in fungi, and factors affecting the removal of HMs.

Use of soil fungi in the biosorption of three trace metals (Cd, Cu, Pb): promising candidates for treatment technology?

Trace metal contamination is a widespread and complex environmental problem. Because fungi are capable of growing in adverse environments, several fungal species could have an interesting potential in remediation technologies for metal contaminated environments. This study proposes to test the ability to tolerate and biosorb three trace metals (Cd, Cu and Pb) of 28 fungal isolates collected from different soils. First, a tolerance assay in agar medium was performed. Each isolate was grown in the presence of Cd, Cu, and Pb at different concentrations. Then, we exposed each soil fungus to 50 mg L^-1 of Cd, Cu, or Pb during 3 days in liquid medium. Parameters such as biomass production, pH, and biosorption were evaluated. The results showed that responses to metal exposure are very diverse even with fungi isolated from the same soil sample, or belonging to the same genera. Several isolates could be considered as good metal biosorbents and could be used in future mycoremediation studies. Among the 28 fungi tested, Absidia cylindrospora biosorbed more than 45% of Cd and Pb, Chaetomium atrobrunneum biosorbed more than 45% of Cd, Cu, Pb, and Coprinellus micaceus biosorbed 100% of Pb.

An overview on heavy metal resistant microorganisms for simultaneous treatment of multiple chemical pollutants at co-contaminated sites, and their multipurpose application

Anthropogenic imbalance of chemical pollutants in environment raises serious threat to all life forms. Contaminated sites often possess multiple heavy metals and other types of pollutants. Elimination of chemical pollutants at co-contaminated sites is imperative for the safe ecosystem functions, and simultaneous removal approach is an attractive scheme for their remediation. Different conventional techniques have been applied as concomitant treatment solution but fall short at various parameters. In parallel, use of microorganisms offers an innovative, cost effective and ecofriendly approach for simultaneous treatment of various chemical pollutants. However, microbiostasis due to harmful effects of heavy metals or other contaminants is a serious bottleneck facing remediation practices in co-contaminated sites. But certain microorganisms have unique mechanisms to resist heavy metals, and can act on different noxious wastes. Considering this significant, my review provides information on different heavy metal resistant microorganisms for bioremediation of different chemical pollutants, and other assistance. In this favour, the integrated approach of simultaneous treatment of multiple heavy metals and other environmental contaminants using different heavy metal resistant microorganisms is summarized. Further, the discussion also intends toward the use of heavy metal resistant microorganisms associated with industrial and environmental applications, and healthcare. PREFACE: Simultaneous treatment of multiple chemical pollutants using microorganisms is relatively a new approach. Therefore, this subject was not well received for review before. Also, multipurpose application of heavy metal microorganisms has certainly not considered for review. In this regard, this review attempts to gather information on recent progress on studies on different heavy metal resistant microorganisms for their potential of treatment of co-contaminated sites, and multipurpose application.

Mechanistic insight to mycoremediation potential of a metal resistant fungal strain for removal of hazardous metals from multimetal pesticide matrix

Fungi have an exceptional capability to flourish in presence of heavy metals and pesticide. However, the mechanism of bioremediation of pesticide (lindane) and multimetal [mixture of cadmium (Cd), chromium (Cr), copper (Cu), nickel (Ni), lead (Pb), zinc (Zn)] by a fungus is little understood. In the present study, Aspergillus fumigatus, a filamentous fungus was found to accumulate heavy metals in the order [Zn(98%)>Pb(95%)>Cd(63%)>Cr(62%)>Ni(46%)>Cu(37%)] from a cocktail of 30 mg L^-1 multimetal and lindane (30 mg L^-1) in a composite media amended with 1% glucose. Particularly, Pb and Zn uptake was enhanced in presence of lindane. Remarkably, lindane was degraded to 1.92 ± 0.01 mg L^-1 in 72 h which is below the permissible limit value (2.0 mg L^-1) for the discharge of lindane into the aquatic bodies as prescribed by European Community legislation. The utilization of lindane as a cometabolite from the complex environment was evident by the phenomenal growth of the fungal pellet biomass (5.89 ± 0.03 g L^-1) at 72 h with cube root growth constant of fungus (0.0211 g^1/3 L^-1/3 h^-1) compared to the biomasses obtained in case of the biotic control as well as in presence of multimetal complex without lindane. The different analytical techniques revealed the various stress coping strategies adopted by A. fumigatus for multimetal uptake in the simultaneous presence of multimetal and pesticide. From the Transmission electron microscope coupled energy dispersive X-ray analysis (TEM-EDAX) results, uptake of the metals Cd, Cu and Pb in the cytoplasmic membrane and the accumulation of the metals Cr, Ni and Zn in the cytoplasm of the fungus were deduced. Fourier-transform infrared spectroscopy (FTIR) revealed involvement of carboxyl/amide group of fungal cell wall in metal chelation. Thus A. fumigatus exhibited biosorption and bioaccumulation as the mechanisms involved in detoxification of multimetals.

Bioremediation process optimization and effective reclamation of mixed carbamate-contaminated soil by newly isolated Acremonium sp

Global pollution from excessive pesticide use has become a serious environmental and public health problem. The aim of the study was to optimize the fungal mediated simultaneous removal of carbofuran and carbaryl from soil. Carb-PV5 strain was isolated from contaminated soil following enrichment culture technique; based on 18S rRNA sequencing, strain was identified as Acremonium sp. (MK514615); Field Emission Scanning Electron Microscopic analysis reflected its morphology. Towards the development of bioaugmentation strategy for the bioremediation of carbamate-contaminated soil, the process parameters were optimized employing Central Composite Rotatable Method. The experimental studies were performed in the range of biomass (0.2-0.6 g kg^-1), temperature (23-33 °C), pH (6-9) and moisture (10-30%). The degradation rate parameters, k and t_1/2 were determined to as 0.475, 0.325 d^-1 and 5.39, 2.1 d with the corresponding r² of 0.9491, 0.9964 for zero and first order, respectively. The cube root growth kinetic constant k of Acremonium sp. varied from 0.0469 to 0.0512 (g^1/3 L^-1/3 h^-1) and 0.0378 to 0.0415 (g^1/3 L^-1/3 h^-1) for carbofuran and carbaryl, respectively. To confirm the model appropriacy and sustainability of the optimization procedure, bioremediation experiments were conducted onto real carbamate-contaminated soils. UPLC and GCMS analysis confirmed the successful removal of carbamates. The current study presents the first report on the bioaugmentation studies carried out on the mixed carbamate contaminated soil using newly isolated Acremonium sp.

Multiple heavy metal tolerance and removal by an earthworm gut fungus Trichoderma brevicompactum QYCD-6

Fungal bioremediation is a promising approach to remove heavy-metal from contaminated water. Present study examined the ability of an earthworm gut fungus Trichoderma brevicompactum QYCD-6 to tolerate and remove both individual and multi-metals. The minimum inhibitory concentration (MIC) of heavy metals [Cu(II), Cr(VI), Cd(II) and Zn(II)] against the fungus was ranged 150–200 mg L⁻¹ on composite medium, and MIC of Pb(II) was the highest with 1600 mg L⁻¹ on potato dextrose (PD) medium. The Pb(II) presented the highest metal removal rate (97.5%) which mostly dependent on bioaccumulation with 80.0%, and synchronized with max biomass (6.13 g L⁻¹) in PD medium. However, on the composite medium, the highest removal rate was observed for Cu(II) (64.5%). Cellular changes in fungus were reflected by TEM analysis. FTIR and solid-state NMR analyses indicated the involvement of different functional groups (amino, carbonyl, hydroxyl, et al.) in metallic biosorption. These results established that the earthworm-associated T. brevicompactum QYCD-6 was a promising fungus for the remediation of heavy-metal wastewater.

Self-assembly biochar colloids mycelial pellet for heavy metal removal from aqueous solution

To effectively improve the heavy metal removal efficiency and stability of biomass adsorbents, a novel biochar colloids-mycelial pellets (BC-MP) composite was prepared via a biological assembly method. BC-MP was successfully produced with increased surface area and multisorption sites by physical adsorption, electrostatic interaction and hydrogen-bond formation between BC and extracellular polymers on MP. To investigate the performance and mechanisms of heavy metal adsorption by BC-MP, batch experiments were conducted with cadmium (Cd (II)) as the model pollutant. Results showed that BC-MP had higher removal efficiency (57.66%) compared to BC (5.45%) and MP (38.45%), respectively, due to the synergistic effect. The maximum adsorption capacity of Cd (II) on BC-MP was 102.04 mg/g based on Langmuir isotherm model. Adsorption kinetics analysis indicated that chemical sorption was the key factor controlling the adsorption of Cd (II) onto BC-MP. Multiple characterization tests revealed that the main mechanisms of the adsorption process were surface complexation, cation exchange and precipitation. The BC-MP composite showed excellent heavy metal removal efficiency with long-term adsorption stability, suggesting its potential as a promising biosorbent for heavy metal removal from industrial wastewater.

Adsorption, recovery, and regeneration of Cd by magnetic phosphate nanoparticles

Adsorption plays an important role in removing cadmium (Cd²⁺) from water, and magnetic adsorbents are increasingly being used due to their ease of separation and recovery. Magnetic Fe₃O₄-coated hydroxyapatite (HAP) nanoparticles (nHAP-Fe₃O₄) were developed by co-precipitation and then used for the removal of Cd²⁺ from water. The properties of these nanoparticles were characterized by transmission electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy, and magnetization curves. Experiments were conducted to investigate the effects of adsorption and mechanisms. Results illustrated that kinetic data were well fitted by a pseudo-second-order model. The adsorption capacity of nHAP-Fe₃O₄ was 62.14 mg/g. The mechanisms for the adsorption of Cd²⁺ on nHAP-Fe₃O₄ included rapid surface adsorption, intraparticle diffusion, and internal particle bonding, with the ion exchange with Ca²⁺ and chemical complexation being the most dominant. The regeneration efficiency and recovery rate of nHAP-Fe₃O₄ eluted by EDTA-Na₂ after the fifth cycle were 63.04% and 40.2%, respectively. Results revealed that the feasibility of nHAP-Fe₃O₄ as an adsorbent of Cd²⁺ and its environmental friendliness make it an ideal focus for future research.

In vivo and in vitro efficient textile wastewater remediation by Aspergillus niger biosorbent

In this work, the treatment of textile wastewater by a facile and high-efficiency technology using eco-friendly Aspergillus niger as a biosorbent was investigated. We measured physical changes (weight, size) during the formation and growth of fungus pellets and the pH values that influence the adsorption performance and biosorption mechanism. Three acid anionic dyes containing Acid Orange 56, Acid Blue 40 and Methyl Blue were chosen as model dyes to investigate batch adsorption efficiency. Two adsorption models (in vivo and in vitro) were adopted to decolorize the acid dyes. The results show that fungus pellets have excellent decoloration abilities with a high adsorption efficiency of 98% for 200 mg L^-1 of acid dye. The pH value of the dye solution varied with the adsorption time and the dye removal efficiency greatly depended on the pH. The bioadsorption mechanism of nano-scale hyphae was revealed to be mainly due to electrostatic interactions caused by the pH change. Furthermore, the surface morphologies of the fungus after adsorption indicated that the dyes had been adsorbed on the surface of the fungus mycelia. Moreover, prepared 3D fungus/GO aerogels demonstrated superior dye removal abilities compared with fungus aerogels.

Detoxification and simultaneous removal of phenolic xenobiotics and heavy metals with endocrine-disrupting activity by the non-ligninolytic fungus Umbelopsis isabellina

Organic and inorganic pollutants well known to interfere with the major functions of the endocrine system co-occur widely in contaminated ecosystems. The aim of the study was to evaluate the ability of Umbelopsis isabellina fungus to simultaneously remove and detoxify multiple environmentally significant endocrine disruptors: the heavy metals Cd(II), Zn(II), Mn(II), Pb(II) and Ni(II) and the phenolic xenobiotics nonylphenol (t-NP), 4-cumylphenol (CP) and 4-tert-octylphenol (4-t-OP). The effects of the metals on fungal growth and efficiency of single-metal uptake were also investigated. U. isabellina exhibited considerable tolerance to Zn(II), Mn(II), Pb(II) and Ni(II), with IC50/24 values ranging from 5.08 for Ni(II) to 13.1 mM for Zn(II). In the presence of CP, the maximum efficiency of Pb(II) removal increased 25% relative to that of the control. Supplementation with Mn(II) or Zn(II) enhanced the 4-t-OP degradation by 18 or 9%, respectively, after 6 h of cultivation. Ecotoxicological assays monitoring bioindicators from different aquatic ecosystems revealed detoxification coinciding with the removal of metals and organic xenobiotics from binary mixtures. This work indicates the potential of a single microorganism, U. isabellina, to remove both heavy metals and organic xenobiotics from co-contaminated sites, making it a suitable candidate for the development of bioremediation strategies.

Advances in exopolysaccharides based bioremediation of heavy metals in soil and water: A critical review

Extracellular polysaccharides or Exopolysaccharides (EPS) are extensively studied bacterial byproducts with high molecular weight attributed to several applications. In spite of their application in the field of food, pharmaceutical, nutraceutical, herbicidal and cosmeceutical industries they were well known for their efficiency in the bioremediation of water and soil tainted with heavy metals. These heavy metals are comparatively high in density than water and are involved in several biological processes. But slight increase in levels can create toxicological bias. The techniques like electrodialysis, chemical precipitation, ion exchange and membrane separation have a lot of disadvantages akin to high energy consumption, high cost, partial exclusion, and creation of poisonous mire. In this context, EPS has a top role to play in the bioremediation of heavy metals. This review gives the critical assessment of the extensive work done to deal this issue by different groups in the last five years. It also explains how different natural circumstances have attributed to the advancement of EPS production, thereby increasing the capacity of bioremediation to deal the issue of heavy metal contamination in both soil and water. A detailed discussion of the EPS formation by bacteria and fungi with their applicability was reported.

Removal of industrial dyes and heavy metals by Beauveria bassiana: FTIR, SEM, TEM and AFM investigations with Pb(II)

Presence of industrial dyes and heavy metal as a contaminant in environment poses a great risk to human health. In order to develop a potential technology for remediation of dyes (Reactive remazol red, Yellow 3RS, Indanthrene blue and Vat novatic grey) and heavy metal [Cu(II), Ni(II), Cd(II), Zn(II), Cr(VI) and Pb(II)] contamination, present study was performed with entomopathogenic fungi, Beauveria bassiana (MTCC no. 4580). High dye removal (88-97%) was observed during the growth of B. bassiana while removal percentage for heavy metals ranged from 58 to 75%. Further, detailed investigations were performed with Pb(II) in terms of growth kinetics, effect of process parameters and mechanism of removal. Growth rate decreased from 0.118 h^-1 (control) to 0.031 h^-1, showing 28% reduction in biomass at 30 mg L^-1 Pb(II) with 58.4% metal removal. Maximum Pb(II) removal was observed at 30 °C, neutral pH and 30 mg L^-1 initial metal concentration. FTIR analysis indicated the changes induced by Pb(II) in functional groups on biomass surface. Further, microscopic analysis (SEM and atomic force microscopy (AFM)) was performed to understand the changes in cell surface morphology of the fungal cell. SEM micrograph showed a clear deformation of fungal hyphae, whereas AFM studies proved the increase in surface roughness (RSM) in comparison to control cell. Homogenous bioaccumulation of Pb(II) inside the fungal cell was clearly depicted by TEM-high-angle annular dark field coupled with EDX. Present study provides an insight into the mechanism of Pb(II) bioremediation and strengthens the significance of using entomopathogenic fungus such as B. bassiana for metal and dye removal.