A novel system coupling an electro-Fenton process and an advanced biological process to remove a pharmaceutical compound, metronidazole

Enhanced metronidazole removal in seawater using a single-chamber bioelectrochemical system

The aim of this study was to investigate the removal of metronidazole (MNZ) from seawater using a bioelectrochemical system (BES). Single-chamber BES (i.e., S-BES) and dual-chamber BES (i.e., D-BES) were constructed with carbon brush as the anode and cathode. With the inoculum of sea mud and 2 g/L of glucose as the substrate in seawater, S-BES and D-BES were acclimated to test the MNZ removal. Results showed that S-BES could remove almost 100 % of 200 mg/L MNZ within 120 h and remain stable within 10 cycles of operation (∼50 d) under the applied voltage of 0.8 V. The MNZ removal reached ∼100 % and 60.2 % in the cathodic and anodic chambers of D-BES fed by 100 mg/L MNZ under 0.8 V, respectively. The MNZ concentration of 200 mg/L significantly inhibited the sulfur metabolism, decreased the ratio of live to dead cells in the electrode biofilms, and thus reduced the SO42- removal in the S-BES. The MNZ degradation and S2- oxidation was mainly attributed to the cathodic and anodic biofilms of S-BES, respectively. Three degradation pathways of MNZ were proposed based on the identified intermediates and results of density functional theory calculations. The synergies among different genus species in the bacterial communities of biofilms, and between anodic and cathodic reactions could be responsible for the high performance of S-BES. Results from this study should be not only useful for the MNZ removal but also for effective MNZ inhibition of sulfate-reducing bacteria induced microbiologically influenced corrosion in seawater.

Composite of a thiacalix[4]arene-copper(I) metal-organic framework and mesoporous carbon for efficient electrochemical detection of antibiotics

Abundant use of nitrofurantoin (NFT) and metronidazole (MTZ) antibiotics has led to excessive residues in the environments and humans, resulting in serious damage to the human body and ecosystem. Therefore, effective detection of NFT and MTZ is exceedingly necessary. In this regard, metal-organic frameworks (MOFs) are promising materials as electrochemical sensors. Herein, we synthesized a new two-dimensional thiacalix [4]arene-copper (I) MOF (Cu-TC4A-M). This MOF was mixed with mesoporous carbon (MC) to a give Cu-TC4A-M@MC composite. In addition, the sensors of Cu-TC4A-M@MC(2:1)/GCE and Cu-TC4A-M@MC(1:2)/GCE were achieved (GCE = glassy carbon electrode), and then were applied for effectively detecting NFT and MTZ, respectively. Markedly, the two sensors exhibited satisfactory linear detection range, anti-interference, reproducibility and stability. When they were utilized in the real samples, such as human serum, urine, tap water and lake water, satisfactory recoveries were attained. The relative standard deviations (RSDs) were in the range of 1.16 % ∼ 1.92 % for NFT and 0.95 % ∼ 2.33 % for MTZ. This work provided a new application prospect for the thiacalix [4]arene-based MOFs as promising candidate materials for NFT and MTZ detection.

Integration of electrochemical processes in a treatment system for landfill leachates based on a membrane bioreactor

The use of electrocoagulation (EC) and anodic oxidation (AO) processes was studied for improving a treatment system for landfill leachates based on a membrane bioreactor (MBR) and a nanofiltration step. The main limitation of the current full-scale system is related to the partial removal of organic compounds that leads to operation of the nanofiltration unit with a highly concentrated feed solution. Application of the EC before the MBR participated in partial removal of the organic load (40 %) with limited energy consumption (2.8 kWh m-3) but with additional production of iron hydroxide sludge. Only AO allowed for non-selective removal of organic compounds. As a standalone process, AO would require a sharp increase of the energy consumption (116 kWh for 81 % removal of total organic carbon). But using lower electric charge and combining AO with EC and MBR processes would allow for achieving high overall removal yields with limited energy consumption. For example, the overall removal yield of total organic carbon was 65 % by application of AO after EC, with an energy consumption of 21 kWh m-3. Results also showed that such treatment strategy might allow for a significant increase of the biodegradability of the effluent before treatment by the MBR. The MBR might then be dedicated to the removal of the residual organic load as well as to the removal of the nitrogen load. The data obtained in this study also showed that the lower electric charge required for integrating AO in a coupled process would allow for strongly decreasing the formation of undesired by-products such as ClO3- and ClO4-.

Advances in identifying and managing emerging contaminants in aquatic ecosystems: Analytical approaches, toxicity assessment, transformation pathways, environmental fate, and remediation strategies

Emerging contaminants (ECs) are increasingly recognized as threats to human health and ecosystems. This review evaluates advanced analytical methods, particularly mass spectrometry, for detecting ECs and understanding their toxicity, transformation pathways, and environmental distribution. Our findings underscore the reliability of current techniques and the potential of upcoming methods. The adverse effects of ECs on aquatic life necessitate both in vitro and in vivo toxicity assessments. Evaluating the distribution and degradation of ECs reveals that they undergo physical, chemical, and biological transformations. Remediation strategies such as advanced oxidation, adsorption, and membrane bioreactors effectively treat EC-contaminated waters, with combinations of these techniques showing the highest efficacy. To minimize the impact of ECs, a proactive approach involving monitoring, regulations, and public education is vital. Future research should prioritize the refining of detection methods and formulation of robust policies for EC management.

An optimized electro-fenton pretreatment for the degradation and mineralization of a mixture of ofloxacin, norfloxacin, and ciprofloxacin

The electro-Fenton process (EFP) is a powerful advanced oxidation process beneficial to treating recalcitrant contaminants, and there has been a continuing interest in combining this technology to enhance the efficiency of conventional wastewater treatment processes. In this work, an optimized EFP process is performed as pretreatment for the degradation and mineralization of three blank fluoroquinolones (FQs) drugs: ofloxacin (OFL), norfloxacin (NOR), and ciprofloxacin (CIP). The optimization of the experiment was carried out using a Box-Behnken experimental design. Faster and complete degradation of the drugs mixture was achieved in 90 min with 61.12 ± 2.0% of mineralization in 180 min, under the optimized conditions: j = 244.0 mA cm-2, [Fe2+] = 0.31 mM, and [FQs] = 87.0 mg L-1. Furthermore, a low toxicity effluent was obtained in 90 min of the experiment, according to bioassay toxicity with Vibrio fischeri. Five short-chain carboxylic acids, including oxalic, maleic, oxamic, formic, and fumaric acids, were detected and quantified, in addition to F- and NO3- inorganic ions. The inhibition of the reactive oxygen species with scavenger proof was also evaluated in this paper.

Adsorption of chloroquine, propranolol, and metformin in aqueous solutions using magnetic graphene oxide nanocomposite

The work proposes the application of a nanocomposite formed by graphene oxide and magnetite to remove chloroquine, propranolol, and metformin from water. Tests related to adsorption kinetics, equilibrium isotherms and adsorbent reuse were studied, and optimization parameters related to the initial pH of the solution and the adsorbent dosage were defined. For all pharmaceuticals, adsorption tests indicated that removal efficiency was independent of initial pH at adsorbent dosages of 0.4 g L-1 for chloroquine, 1.2 g L-1 for propranolol, and 1.6 g L-1 for metformin. Adsorption equilibrium was reached within the first few minutes, and the pseudo-second-order model represented the experimental data well. While the equilibrium data fit the Sips isotherm model at 298 K, the predicted maximum adsorption capacities for chloroquine, propranolol, and metformin were 44.01, 16.82, and 12.23 mg g-1, respectively. The magnetic nanocomposite can be reused for three consecutive cycles of adsorption-desorption for all pharmaceuticals, being a promising alternative for the removal of different classes of pharmaceuticals in water.

Treatment of petroleum hydrocarbon contaminated soil by combination of electro-Fenton and biosurfactant-assisted bioslurry process

Removing petroleum hydrocarbons (PHCs) from polluted soil is challenging due to their low bioavailability and degradability. In this study, an experiment was carried out to treat soil polluted with petroleum hydrocarbon using a hybrid electro-Fenton (with BDD anode electrode) and biological processes stimulated with long-chain rhamnolipids (biosurfactants). Electro-Fenton treatment was applied as a pretreatment before the biological process to enhance PHC biodegradability, which would benefit the subsequent biological process. The effects of initial pH, hydroxide concentration, soil organic matter composition, PHCs intermediates during the electro-Fenton process, and total numbers of bacteria in the biological process were analyzed to determine the optimum conditions. The results showed that the optimized electrolysis time for the electro-Fenton was 12 h. The change induced during pretreatment at a specified time was found suitable for the biological process stage and led to 93.6% PHC degradation in combination with the electro-Fenton-and-biological process after 72 h. The combined system's performance was almost 40% higher than individual electro-Fenton and biological treatments. GC-MS analysis confirms the formation of 9-octadecen-1-ol (Z), 2-heptadecene, 1-nonadecene, 1-heneicosene, and pentacosane as fragmentation during the PHCs degradation process. Thus, the electro-Fenton process as pretreatment combined with a biological process stimulated with rhamnolipids (biosurfactants) could be effectively applied to remediate soil polluted with PHCs. However, the system needs further research and investigation to optimize electrolysis time and biosurfactant dose to advance this approach in the soil remediation process.

Recent advances in the biological treatment of wastewater rich in emerging pollutants produced by pharmaceutical industrial discharges

Pharmaceuticals and personal care products present potential risks to human health and the environment. In particular, wastewater treatment plants often detect emerging pollutants that disrupt biological treatment. The activated sludge process is a traditional biological method with a lower capital cost and limited operating requirements than more advanced treatment methods. In addition, the membrane bioreactor combines a membrane module and a bioreactor, widely used as an advanced method for treating pharmaceutical wastewater with good pollution performance. Indeed, the fouling of the membrane remains a major problem in this process. In addition, anaerobic membrane bioreactors can treat complex pharmaceutical waste while recovering energy and producing nutrient-rich wastewater for irrigation. Wastewater characterizations have shown that wastewater's high organic matter content facilitates the selection of low-cost, low-nutrient, low-surface-area, and effective anaerobic methods for drug degradation and reduces pollution. However, to improve the biological treatment, researchers have turned to hybrid processes in which all physical, chemical, and biological treatment methods are integrated to remove various emerging contaminants effectively. Hybrid systems can generate bioenergy, which helps reduce the operating costs of the pharmaceutical waste treatment system. To find the most effective treatment technique for our research, this work lists the different biological treatment techniques cited in the literature, such as activated sludge, membrane bioreactor, anaerobic treatment, and hybrid treatment, combining physicochemical and biological techniques.

Degradation of antibiotics by electrochemical advanced oxidation processes (EAOPs): Performance, mechanisms, and perspectives

Global consumption and discharge of antibiotics have led to the rapid development and spread of bacterial antibiotic resistance. Among treatment strategies, electrochemical advanced oxidation processes (EAOPs) are gaining popularity for treating water/wastewater containing antibiotics due to their high efficiency and easiness of operation. In this review, we summarize various forms of EAOPs that contribute to antibiotic degradation, including common electrochemical oxidation (EO), electrolyte enhanced EO, electro-Fenton (EF) processes, EF-like process, and EAOPs coupling with other processes. Then we assess the performance of various EAOPs in antibiotic degradation and discuss the influence of key factors, including electrode, initial concentration and type of antibiotic, operation conditions, electrolyte, and water quality. We also review mechanisms and degradation pathways of various antibiotics degradation by EAOPs, and address the species and toxicity of intermediates produced during antibiotics treatment. Finally, we highlight challenges and critical research needs to facilitate the application of EAOPs in antibiotic treatment.

Composite fabrication and characterization of crosslinked polyaniline/Pterocladia capillacea-activated carbon for adsorption of direct blue-86 dye from water

The fabrication of crosslinked polyaniline/Pterocladia capillacea-activated carbon composite (CrossPANI/P-AC) at different ratios (1:0, 1:0.2, 1:0.6, and 1:1) was studied. CrossPANI/P-AC composites were fabricated by the in situ polymerization of aniline using hydrogen chloride as an acidic dopant, and ammonium persulfate as initiator, while Pterocladia capillacea-activated carbon was synthesized by the chemical activation method and incorporated into the polymer matrix. The samples were characterized by the terms such as Fourier transform infrared (FTIR) spectroscopy, Brunauer–Emmett–Teller, X-ray diffraction (XRD), thermogravimetric analysis, scanning electron microscopy, and energy-dispersive X-ray spectroscopy (EDX). FTIR spectroscopy showed the main characteristic peak positions of CrossPANI/P-AC; XRD showed low crystallinity of CrossPANI/P-AC. A high specific surface area for CrossPANI/P-AC was achieved at a ratio of 1:0.2 where Brunauer–Emmett–Teller surface area, total pore volume, and mean pore diameter values were 166.10 m2/g, 0.0141 cm3/g, and 3.40 nm, respectively. The capability of CrossPANI/P-AC (1:0.2) composite as adsorbent for Direct blue-86 (DB-86) dye from aqueous solution was investigated. The impact of initial dye concentration, temperature, pH, and contact time on the DB-86 dye adsorption from its water solution was examined. The equilibrium adsorption data were well represented by the Langmuir isotherm achieving maximum monolayer capacity (Qm) of 163.93 mg/g at a dose of 0.5 g/L. In contrast, the kinetic adsorption data were well fit by the pseudo-second-order model. Thermodynamic analysis demonstrated that DB-86 dye adsorption occurs spontaneously, endothermically, and physically in nature. The results demonstrated that these composites effectively removed DB-86 dye from aqueous solutions and could be recycled.

Graphical abstract

Emerging bio-dispersant and bioremediation technologies as environmentally friendly management responses toward marine oil spill: A comprehensive review

Marine oil spills emanating from wells, pipelines, freighters, tankers, and storage facilities draw public attention and necessitate quick and environmentally friendly response measures. It is sometimes feasible to contain the oil with booms and collect it with skimmers or burn it, but this is impracticable in many circumstances, and all that can be done without causing further environmental damage is adopting natural attenuation, particularly through microbial biodegradation. Biodegradation can be aided by carefully supplying biologically accessible nitrogen and phosphorus to alleviate some of the microbial growth constraints at the shoreline. This review discussed the characteristics of oil spills, origin, ecotoxicology, health impact of marine oils spills, and responses, including the variety of remedies and responses to oil spills using biological techniques. The different bioremediation and bio-dispersant treatment technologies are then described, with a focus on the use of green surfactants and their advances, benefits/drawbacks. These technologies were thoroughly explained, with a timeline of research and recent studies. Finally, the hurdles that persist as a result of spills are explored, as well as the measures that must be taken and the potential for the development of existing treatment technologies, all of which must be linked to the application of integrated procedures.

Limitations and future directions of application of the Fenton-like process in micropollutants degradation in water and wastewater treatment: A critical review

Growing water scarcity and pollution are the main challenges that scientists need to focus on currently. Fenton-like processes are promising for applications related to water and wastewater treatment. Although there have been reviews on the fundamentals and applications of Fenton oxidation, a review focusing on the limitations of Fenton oxidation and their possible solutions is still insufficient. This review summarises the features, advantages, and drawbacks of the classic Fenton process. A comprehensive literature survey was conducted to review studies conducted over the last few decades dealing with the application of Fenton processes to organic pollutant removal from water and wastewater. The present overview highlights the modifications of Fenton processes focusing on industrial applications in water and wastewater treatment, especially for micropollutant degradation. Additionally, this study reviews the possibilities and future directions of research on Fenton-like processes to enable the incorporation of Fenton-based methods into existing water and wastewater treatment technologies, including industrial wastewater. It also presents a novel technological solution and improvements to the Fenton-like process to improve the efficiency and reduce the cost.

Progress of homogeneous and heterogeneous electro-Fenton treatments of antibiotics in synthetic and real wastewaters. A critical review on the period 2017-2021

Antibiotics are widely supplied over all the world to animals and humans to fight and heal bacteriological diseases. The uptake of antibiotics has largely increased the average-life expectancy of living beings. However, these recalcitrant products have been detected at low concentrations in natural waters, with potential health risks due to alterations in food chains and an increase in the resistance to bacterial infection, control of infectious diseases, and damage of the beneficial bacteria. The high stability of antibiotics at mild conditions prevents their effective removal in conventional wastewater treatment plants. A powerful advanced oxidation processes such as the electro-Fenton (EF) process is being developed as a guarantee for their destruction by ^•OH generated as strong oxidant. This review presents a critical, exhaustive, and detailed analysis on the application of EF to remediate synthetic and real wastewaters contaminated with common antibiotics, covering the period 2017-2021. Homogeneous EF and heterogeneous EF involving iron solid catalysts or iron functionalized cathodes, as well as their hybrid and sequential treatments, are exhaustively examined. Their fundamentals and characteristics are detailed, and the main results obtained for the removal of the most used antibiotic families are carefully described and discussed. The role of generated oxidizing agents is explained, and the by-products generated, and reaction sequences proposed are detailed.