Uranium capture by a layered 2D/2D niobium phosphate/holey graphene architecture via an electro-adsorption and electrocatalytic reduction coupling process

Ultra-high capacity and selectivity for uranium fixation by carbon nanosphere supported hydroxyapatite nanorod adsorbent

Uranium (U(VI)) has chemical and radiological toxicity, so the effective treatment of uranium-containing wastewater is crucial for both environmental safety and human health. Here, a carbon nanosphere (CNS) supported hydroxyapatite (HAP) nanorod (HAP/CNS) adsorbent was prepared using a simple glucose-assisted hydrothermal method toeffectively immobilize U(VI). Glucose not only derived CNS, but also facilitated HAP crystallization, prohibited HAP aggregation, and introduced oxygen-containing functional groups (i.e., COOH). The optimized HAP/CNS possessed a fantastic adsorption capability of 3080.3 mg/g for U(VI), nearly three times that of HAP and much higher than many reported HAP-based adsorbents. Notably, HAP/CNS was less affected by coexisting ions (distribution coefficient, Kd, researched 6.0 × 104 mL/g) and humic acid, and maintained good capability for real wastewater. The pseudo-second-order kinetic model and Langmuir isotherm model could better explain U(VI) removal behavior by HAP/CNS. Results showed that HAP/CNS and UO22+ combined to form a new uranium-containing compound, i.e., calcium-uranium mica (Ca(UO2)2(PO4)2·3H2O) via ion exchange and dissolution-precipitation, which should be the main reason for the ultra-high capacity and selectivity of HAP/CNS. Additionally, the hydrophilic oxygen-containing functional groups synergistically facilitated U(VI) fixation through complexation. This work introduces a superior adsorbent for purifying uranium-contaminated wastewater and elucidates its synergetic mechanism in uranium fixation.

Sustainable Uranium Extraction via Reversible Uranyl Carbonate Capture-Release Cycling Stemming from Weak Interaction with Self-Supporting Covalent Organic Frameworks

Extracting abundant uranium resources from the ocean would contribute greatly to the sustainable development of nuclear energy. In this work, it is found that the imine N, phenol-bidentate chelation groups from imine-Covalent-Organic Frameworks (COFs) are superior sites for the weak complexation with uranyl carbonate species. The surprisingly low binding energy of -13.36 kcal mol-1 originating from the weak coordination bond and hydrogen bond benefits to the readily spontaneous decomplexation of the chelated uranyl carbonate species by CO3 2- ions. Through the rational design of three COFs with uniform imine N, phenol-bidentate sites but varied amine monomer geometry, i.e., pyrene COF (Py-COF), 1,3,5-Triazine COF (TTA-COF) and porphyrin COF (TAPP-COF), it's found that the abundantly available imine N, phenol-bidentate sites ensured by the high specific surface area and strong hydrophilicity of Py-COF and TTA-COF result in the highly reversible uranyl capture-release during the cycled extraction of uranyl carbonate from seawater and mild elution with 2.0 mM Na2CO3 solution. With the 3.0 × 3.0 cm2 self-supported plate fabricated by Py-COF growth on carbon cloth, a record high uranium extraction capacity of 45 mg g-1 (i.e., 3.0 mg g-1 day-1) from seawater is achieved within 15 days' capture-release cycles.

A synergistic coordination-reduction interface for electrochemical reductive extraction of uranium with low impurities from seawater

Electrochemical extraction of uranium from seawater is a promising strategy for the sustainable supply of nuclear fuel, whereas the current progress suffers from the co-deposition of impurities. Herein, we construct a synergistic coordination-reduction interface in CMOS@NSF, achieving electrochemical extraction of black UO2 product from seawater. The internal sulfur of CoMoOS tailors the electron distribution, resulting in the electron accumulation of terminal O sites for strong uranyl binding. Meanwhile, the interfacial connection of CoMoOS with Ni3S2 accelerates the electron transfer and promoted the reductive properties. Such synergistic coordination-reduction interface ensures the formation and preservation of tetravalent uranium, preventing the co-deposition of alkalis in crystalline transformation. From natural seawater, CMOS@NSF exhibits an electrochemical extraction capacity of 2.65 mg g-1 d-1 with black UO2 solid products as final products. This work provides an efficient strategy for the electrochemical uranium extraction from seawater with low impurities.

Combining Electrosorption and Electrochemical Reduction Mechanisms for Uranium Removal Using 1,2,3,4-Butane Tetracarboxylic Acid-Modified MIL-101: An In-Depth Exploration of Uranyl-Adsorbent Interactions

Extracting uranium from nuclear wastewater is vital for environmental and human health protection. However, despite progress in uranium extraction, there remains a demand for an optimized adsorbent with improved capability, efficiency, and selectivity. To bridge this gap, 1,2,3,4-butane tetracarboxylic acid (BTCA)-modified MIL-101 was synthesized through a simple hydrothermal reaction between amino-modified MIL-101 (MIL-101-NH2) and BTCA. Density Functional Theory calculations validated the formation of stable coordination bonds and a hydrogen bond network, bolstering the adsorption capacity. To further enhance this capacity, the influence of an electric field on adsorption performance was investigated. Studies revealed that uranyl ion removal under an electric field involves both electrosorption and electroreduction pathways. This dual mechanism not only significantly increases the adsorption capacity from 221.1 mg g-1 to 331.4 mg g-1 but also improves the adsorption efficiency. These insights not only enhance our understanding of effective uranium removal but also foster the development of sustainable, ecofriendly technologies in the nuclear energy field.

Construction of hierarchical porous and polydopamine/salicylaldoxime functionalized zeolitic imidazolate framework-8 via controlled etching for uranium adsorption

Efficient uranium extraction from seawater is critical for the development of the nuclear industry. Herein, a polydopamine/salicylaldoxime decorated hierarchical zeolitic imidazolate framework-8 (H-PDA/SA-ZIF-8) is constructed by using a controlled etching process. Benefiting from the combination of PDA/SA and the zeolitic imidazolate framework-8 (ZIF-8), as well as a controlled etching process, the H-PDA/SA-ZIF-8 possesses multiaffinity sites, excellent specific surface area (1234.92 m2 g-1), and a hierarchical pore structure. The H-PDA/SA-ZIF-8 exhibits excellent adsorption capacity (Qm = 869.6 mg g-1), selectivity, and reusability in uranium adsorption. The adsorption process of H-PDA/SA-ZIF-8 fits very well with the Langmuir isotherm model and pseudo-second-order models, and the adsorption process equilibrates within 20 min (C0 = 20 mg L-1). Furthermore, the H-PDA/SA-ZIF-8 shows remarkable antibacterial ability. Impressively, the adsorption capacity of H-PDA/SA-ZIF-8 to uranium in natural seawater reaches 6.9 mg g-1 after circulation for 15 days. Therefore, the H-PDA/SA-ZIF-8 is a promising and fascinating material for uranium extraction from natural seawater.

Enhanced Photocatalytic Removal of U(VI) from Real Radioactive Wastewater by Modulating the Surface Charge Microenvironment in Porphyrin-Based Hydrogen-Bonded Organic Framework

Reduction of soluble U(VI) to insoluble U(IV) based on photocatalysts is a simple, environmentally friendly, and efficient method for treating radioactive wastewater. The present study involved the systematic comparison of the photoelectric properties of three metalloporphyrins with different metal centers and the synthesis of a novel porphyrin-based hydrogen-bonded organic framework (Ni-pHOF) photocatalyst by modulating the surface charge microenvironment in porphyrin for enhanced photocatalytic removal of U(VI) from wastewater. Compared to the metal-free HOF, the surface charge microenvironment around the Ni atom in Ni-pHOF accelerated the reduction kinetics of U(VI) under visible light illumination at the initial moment, showing a high removal rate, even in air. The removal rate of U(VI) from aqueous solution by Ni-pHOF can achieve over 98% in the presence of coexisting nonoxidizing cations and only decreased by less than 8% after five cycles, exhibiting high selectivity and good reusability. Furthermore, Ni-pHOF can remove 86.74% of U(VI) from real low-level radioactive wastewater after 120 min of illumination, showcasing practical application potential. Density functional theory (DFT) calculations and electron paramagnetic resonance (EPR) spectra indicated that modulating the surface charge microenvironment in Ni-pHOF through porphyrin metallization is conducive to improving the charge separation efficiency, prompting more e- and •O2- to participate in the reduction reaction of U(VI). This work provides new insights into the metallization of porphyrin-based HOFs and paves a new way for the tailoring of porphyrin-based HOFs/COFs by modulating the surface charge microenvironment to achieve efficient recovery of U(VI) from real radioactive wastewater.

Anchoring chitosan/phytic acid complexes on polypyrrole nanotubes as capacitive deionization electrodes for uranium capture from wastewater

Capacitive deionization (CDI) technology holds great potential for rapid and efficient uranyl ion removal from wastewater. However, the related electrode materials still have much room for research. Herein, chitosan/phytic acid complexes were anchored on polypyrrole nanotubes (CS/PA-PPy) to fabricate the electrode for the electrosorption of uranyl ions (UO22+). In this system, polypyrrole nanotubes provided specific channels for ion and electron diffusion, and chitosan/phytic acid complexes offered selective sites for UO22+ binding. The results demonstrated that CS/PA-PPy via electrosorption showed faster kinetics and higher uranium uptake than those via physicochemical adsorption. The maximum adsorption capacity toward UO22+ via electrosorption (1.2 V) could reach 799.3 mg g-1, which was higher than most of the reported CDI electrodes. Electrochemical measurements and experimental characterizations showed that the electrosorption of UO22+ by CS/PA-PPy was a synergistic effect of capacitive process and physicochemical adsorption, in which the capacitive mechanism involved the formation of an electric double layer from hollow polypyrrole nanotubes, whereas the coordination of phosphate, amino and hydroxyl groups with UO22+ was attributed to physicochemical adsorption. With the rational design of material, along with its excellent uranium removal performance, this work exhibited a novel and potential composite electrode for uranium capture via CDI from wastewater.

Redox-active phytic acid-based self-assembled hybrid material for enhanced uranium adsorption from highly acidic solution

Achieving efficient uranium adsorption from highly acidic wastewater is still considered challenging. Here, an inorganic-organic hybridized self-assembly material (rPFE-10) with redox activity was constructed by phytic acid (PA), ethylenediamine (EDA), and Fe(II) via a facile one-pot route, and further applied for U(VI) removal. In the static adsorption experiment, rPFE-10 achieved the maximum U(VI) adsorption capacity of 717.1 mg/g at the optimal pH of 3.5. It also performed preeminently in a highly acidic condition of pH = 1.0, with the highest adsorption capacity of 551.2 mg/g and an equilibrium time of 30 min. Moreover, rPFE-10 exhibited a pH-responsive adsorption selectivity for U(VI) and An-Ln (S(U(VI)) and S(An-Ln)), which increased to 69 % and 94 % respectively as pH decreased from 3.0 to 1.0. Additionally, the spectral analysis revealed a reconstruction mechanism induced by multiple synergistic adsorption, in which U(VI) exchange with EDA+/2+ and Fe2+/3+ and earned suitable coordination geometry and ligand environment to coordinate with PA (mainly P-OH), while partial U(VI) is reduced by Fe(II) in framework. This work not only highlights the facile strategy for enhanced U(VI) retention in highly acidic solution, but expands the potential application of supramolecular self-assembly material in treatment of nuclear wastewater.

Hydrolyzed Hydrated Titanium Oxide on Laser-Induced Graphene as CDI Electrodes for U(VI) Adsorption

Recently, laser-induced graphene (LIG), which has been successfully applied in CDI technology (directly without a complex preparation process), has gained considerable attention. However, the raw LIG electrode with a limited number of active sites exhibits low adsorption efficiency. Therefore, the search for a suitable and effective method to modify LIG to improve its electroadsorption performance is significant. Herein, a very simple titration hydrolysis method is adopted to modify LIG, resulting in a layer of hydrated titanium oxide (HTO) being synthesized on the surface of LIG. The LIG/HTO composites possess a good adsorption property since covering the surface of LIG with a layer of HTO can greatly improve the adsorption capacity of LIG. Moreover, with the addition of HTO, not only the proton transfer ability of LIG has been enhanced but also considerable specific capacitance has been enlarged. As a result, LIG/HTO composite as CDI electrode displays a maximum theoretical adsorption capacity of 1780.89 mg/g at 1.2 V, and the capacitance of LIG/HTO composite material is 4.74 times higher than LIG. During the electroadsorption process, Ti4+ is reduced to Ti3+ under external voltage, and O2- is produced through oxidation. Meanwhile, part of the U (VI) is hydrolyzed into UO3·2H2O under the action of -OH, and some combine with O2- to produce UO4·4H2O.

Flexible self-supporting Na3MnTi(PO4)3@C fibers for uranium extraction from seawater by electro sorption

As an eco-friendly technique with the superior adsorption performance, electroadsorption has shown great potential for application in uranium (U(VI)) recovery in recent years. However, the electrodes used in the electrosorption generally suffer the adsorbent to be loaded on the conductors, which greatly limited the adsorption performance of the electrodes for uranyl ions. In present study, a flexible self-supporting Na3MnTi(PO4)3@C fibers (NMTP@C fibers) electrode material was rationally designed and prepared by electrostatic spinning method and annealing technique, and its ability to capture U(VI) efficiently was preliminarily demonstrated by batch adsorption and electro sorption. The plentiful phosphate groups provide sufficient active sites for adsorption, while the axially continuous electron conduction and radially short-range ion transport give NMTP@C fibers fast charge/ion transport capability. The NMTP@C fiber can remove 99% of 5 ppm U(VI) in seawater by electro absorption within 1 h. After several cycles of adsorption under seawater conditions, the adsorbent can still maintain a stable adsorption capacity. The adsorption mechanism of NMTP@C nanofibers for U(VI) was investigated by XPS, FT-IR, Raman, SEM-EDS, and XRD, which was electrostatic interactions and surface complexation. These results suggest that NMTP@C fibers are promising high-capacity adsorbents for efficient and selective capture of U(VI) from seawater.

Construction of amidoxime-functionalized magnetic hydroxyapatite with enhanced uranium extraction performance from aqueous solution and seawater

A novel amidoxime-functionalized magnetic hydroxyapatite (AFNH) was successfuly fabricated to extract uranium from aqueous solution and seawater. The introduction of amidoxime group not only increased the number of active site of AFNH to speed up the adsorption rate and increase the extraction capacity, but also adjusted the optimal extraction pH from 4 to 8, which was beneficial for capturing uranium from seawater. The maximum adsorption capacity and adsorption efficiency at pH 8 were 945.2 mg g-1 and 99.2%, respectively. AFNH still had good removal efficiency (above 90%) after five cycles, indicating the good regeneration of AFNH. After uranium adsorption, AFNH could be easily recycled by magnetic separation due to its magnetism. In simulated seawater, AFNH also showed excellent uranium removal performance with high adsorption efficiency (84.9%) and adsorption capacity (1.70 mg g-1). Furthermore, the 14-day uranium extraction capacity of AFNH in natural seawater could reach 5.93 mg g-1. The SEM, FTIR, XRD and XPS analyses showed that the enhanced uranium extraction performance of AFNH was mainly attributed to electrostatic interaction, complexation and co-precipitation. In conclusion, AFNH was expected to be a candidate as adsorbent with great potential in extracting uranium from seawater.

Mn, N co-doped carbon nanospheres for efficient capture of uranium (VI) via capacitive deionization

Heteroatom doping, involving the introduction of atoms with distinct electronegativity into carbon materials, has emerged as an effective approach to optimize their charge distribution. In this study, we designed a strategy to synthesize in-situ Mn, N co-doped carbon nanospheres (Mn-NC) through the polycondensation of 2,6-diaminopyridine and formaldehyde in synchronization with Mn2+ chelation to form Mn-polytriazine precursor, followed by calcination to form carbonaceous solid. Then Mn-NC was fabricated into a capacitive deionization (CDI) electrode for the selective removal of uranium ions (U (VI)), which is commonly found in radioactive water. Interestingly, Mn-NC exhibited good selectivity for UO22+ capture with a demonstrated adsorption capacity of approximately 194 mg/g @1.8 V. The systematic analysis of the adsorption mechanism of UO22+ revealed that N dopants within Mn-NC can coordinate with the U (VI) ions, thereby facilitating the removal process. Our study presents a straightforward and convenient strategy for removing UO22+ ions by harnessing the coordination effect, eliminating the requirement for pore size control.

Enhancement of CdS resistance to photocorrosion and photocatalytic removal of uranyl by complexation with N-deficient g-C3N4under aerobic conditions

The effect of oxygen on the reduction of uranyl and photocorrosion of CdS remains a pressing issue when CdS is used as a photocatalyst for the removal of uranyl in uranium-containing wastewater. In this study, composites (CdS/PCN) were prepared by designing N-deficient g-C₃N₄ composite with CdS for efficient photocatalytic reduction of uranyl under aerobic condition. Meanwhile, a series of characterizations of the CdS/PCN composites were carried out by XRD, FT-IR, XPS, EDS and UV-vis. Surprisingly, the CdS/PCN not only showed very high photocatalytic reduction activity for uranyl under aerobic condition, but also the photocorrosion of CdS by oxygen and h⁺ was inhibited. With a starting uranium (VI) concentration of 20 ppm, the uranium (VI) removal efficiency could reach 97.33% (dark: 30 min, light: 10 min). Interestingly, the removal efficiency was better in air condition than in pure nitrogen or 30% oxygen atmosphere, i.e. a proper amount of oxygen has accelerated the reduction reaction, while excess oxygen weakened the reduction. Finally, a new mechanism of reduction of uranyl by CdS/PCN photocatalyst was given under aerobic condit ions. This work presents a novel strategy for reduction of U(VI) by photocatalysis and the inhibition of photocorrosion of photocatalysts under aerobic conditions.

Graphene-Based Adsorbents for Arsenic, Fluoride, and Chromium Adsorption: Synthesis Methods Review

Water contamination around the world is an increasing problem due to the presence of contaminants such as arsenic, fluoride, and chromium. The presence of such contaminants is related to either natural or anthropogenic processes. The above-mentioned problem has motivated the search for strategies to explore and develop technologies to remove these contaminants in water. Adsorption is a common process employed for such proposals due to its versatility, high adsorption capacity, and lower cost. In particular, graphene oxide is a material that is of special interest due to its physical and chemical properties such as surface area, porosity, pore size as well as removal efficiency for several contaminants. This review shows the advances, development, and perspectives of materials based on GO employed for the adsorption of contaminants such as arsenite, arsenate, fluoride, and hexavalent chromium. We provided a detailed discussion of the synthesis techniques and their relationship with the adsorption capacities and other physical properties as well as pH ranges employed to remove the contaminants. It is concluded that the adsorption capacity is not proportional to the surface area in all the cases; instead, the synthesis method, as well as the functional groups, play an important role. In particular, the sol-gel synthesis method shows better adsorption capacities.