Removal of sudan dyes from aqueous solution by magnetic carbon nanotubes: Equilibrium, kinetic and thermodynamic studies

Supercritical Phase Inversion to Produce Photocatalytic Active PVDF-coHFP_TiO2 Composites for the Degradation of Sudan Blue II Dye

TiO2-loaded poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-coHFP) membranes were produced by supercritical CO2-assisted phase inversion. Three different TiO2 loadings were tested: 10, 20, and 30 wt% with respect to the polymer. Increasing the TiO2 amount from 10 wt% to 20 wt% in the starting solution, the transition from leafy-like to leafy-cellular morphology was observed in the section of the membrane. When 30 wt% TiO2 was used, the entire membrane section showed agglomerates of TiO2 nanoparticles. These polymeric membranes were tested to remove Sudan Blue II (SB) dye from aqueous solutions. The adsorption/photocatalytic processes revealed that membrane morphology and TiO2 cluster size were the parameters that mainly affected the dye removal efficiency. Moreover, after five cycles of exposure of these membranes to UV light, SB removal was higher than 85%.

Electrochemical monitoring sensors of water pollution systems

Analytical techniques as strong, precise, and expensive are necessary for monitoring food and water safety for contaminants, microorganisms, and allergies that might be harmful if used. Sudan dyes are commonly utilized as an ingredient in food dye substances and a variety of industrial items. These colors are classified as three carcinogens and are linked to liver and bladder cancers. They are not authorized for human consumption by the International Agency for Research on Cancer (IARC) and are not permitted to be used by the Food Standards Agency or the European Union. This article describes electrochemical dye analysis beside the numerous electrochemical sensors utilized to identify these dyes as a food colorant and water. As a result, the qualities, chemistry, and toxicity of dyes as food colorants and industrial goods in Sudan have been investigated in this study. Sudan dyes have been thoroughly studied, and many electrochemical sensors have been developed to define and monitor these dyes in food colorants. As a result, current electrochemical sensors have been found to be neither mass-production nor cost-effective. Mostly, the synthesis of high-performance materials needs high knowledge, and the production of electrode surfaces is remained difficult due to labor-intensive and time-consuming activities.

Recent advances in magnetic carbon nanotubes: synthesis, challenges and highlighted applications

Magnetic carbon nanotubes (MCNTs), consisting of carbon nanotubes (CNTs) and magnetic nanoparticles (MNPs), have enormous exploration and application potentials due to their superior physical and chemical properties, such as unique magnetism and high enrichment performance. This review concentrates on the rapid advances in the synthesis and application of magnetic carbon nanotubes. Great progress has been made in the preparation of MCNTs by developing methods including chemical vapor deposition, pyrolysis procedure, sol-gel process, template-based synthesis, filling process and hydrothermal/solvothermal method. Various applications of MCNTs as a mediator of the adsorbent in magnetic solid-phase extraction, sensors, antibacterial agents, and imaging system contrast agents, and in drug delivery and catalysis are discussed. In order to overcome the drawbacks of MCNTs, such as sidewall damage, lack of convincing quantitative characterization methods, toxicity and environmental impact, and deficiency of extraction performance, researchers proposed some solutions in recent years. We systematically review the latest advances in MCNTs and discuss the direction of future development.

Biosorption of cationic and anionic dyes using the biomass of Aspergillus parasiticus CBS 100926T

Aspergillus parasiticus (A. parasiticus) CBS 100926^T was used as a biosorbent for the removal of Methylene Blue (MB), Congo Red (CR), Sudan Black (SB), Malachite Green Oxalate (MGO), Basic Fuchsin (BF) and Phenol Red (PR) from aqueous solutions. The batch biosorption studies were carried out as a function of dye concentration and contact time. The biosorption process followed the pseudo-first-order and the pseudo-second-order kinetic models and the Freundlich and Langmuir isotherm models. The resulting biosorbent was characterized by Scanning Electron Microscopy (SEM), X-Ray Diffractometer and Fourier Transformer Infrared Spectroscopy (FTIR) techniques. The results of the present investigation suggest that A. parasiticus can be used as an environmentally benign and low cost biomaterial for the removal of basic and acid dyes from aqueous solution.

Adsorption of Sudan-IV contained in oily wastewater on lipophilic activated carbons: kinetic and isotherm modelling

Up to nine kinetic and fourteen isotherm adsorption models are employed to model the adsorption of Sudan IV, a lipophilic model pollutant present in a biphasic mixture of cyclohexane-water system to simulate oily wastewater. Six different modified activated carbons were used as adsorbents. The highest amount adsorbed of Sudan IV was found in the material prepared by successive treatments of the parent commercial activated carbon Norit ROX 0.8 with nitric acid and urea, followed by thermal treatment at 800 °C under continuous flow of nitrogen. Kinetic and isotherm adsorption models can be employed to simulate the process, since the effect of the presence of water in the adsorption of Sudan IV from the cyclohexane phase was found to be negligible, owing to the high lipophilic character of both adsorbent and adsorbate. All kinetic and isotherm coefficients, coupling with statistical parameters (r², adjusted r² and sum of squared errors), are determined by non-linear regression fitting and compared to literature data. The model of Avrami is found to be the most appropriate model to represent the adsorption of the pollutant in any of the six modified carbons tested, the highest value of the kinetic constant being 0.055 min^-1. The isotherm adsorption is well-modelled by using the general isotherm equation of Tóth and the multilayer Jovanović expression for the adsorption of Sudan-IV on that material, resulting in a high monolayer uptake capacity (q_m = 193.6 mg g^-1).

The Nanosized Dye Adsorbents for Water Treatment

Clean water is a vital element for survival of any living creature and, thus, crucially important to achieve largely and economically for any nation worldwide. However, the astonishingly fast trend of industrialization and population growth and the arisen extensive water pollutions have challenged access to clean water across the world. In this regard, 1.6 million tons of dyes are annually consumed. Thereof, 10%–15% are wasted during use. To decolorize water streams, there is an urgent need for the advanced remediation approaches involving utilization of novel materials and technologies, which are cost and energy efficient. Nanomaterials, with their outstanding physicochemical properties, can potentially resolve the challenge of need to water treatment in a less energy demanding manner. In this review, a variety of the most recent (from 2015 onwards) opportunities arisen from nanomaterials in different dimensionalities, performances, and compositions for water decolorization is introduced and discussed. The state-of-the-art research studies are presented in a classified manner, particularly based on structural dimensionality, to better illustrate the current status of adsorption-based water decolorization using nanomaterials. Considering the introduction of many newly developed nano-adsorbents and their classification based on the dimensionality factor, which has never been employed for this sake in the related literature, a comprehensive review will be presented.

One-step preparation of polyimide-inlaid amine-rich porous organic block copolymer for efficient removal of chlorophenols from aqueous solution

A novel polyimide-inlaid amine-rich porous organic block copolymer (PI-b-ARPOP) was prepared via one-step polymerization by using different molar ratios of melamine (MA)/terephthalaldehyde (TA)/pyromellitic dianhydride (PMDA), at molar ratios of 4/3/1, 4/2/2 and 4/1/3. The copolymer contained both aminal groups belonging to ARPOP and imide groups belonging to PI, and the bonding styles of the monomers and growth orientations of the polymeric chains were diversiform, forming an excellent porous structure. Notably, MA/TA/PMDA (4/2/2) had a surface area and pore volume of 487.27 m²/g and 1.169 cm³/g, respectively. The adsorption performance of the materials towards 2,4-dichlorophenol (2,4-DCP) in ultra-pure water was systematically studied. The pH value of 7 was optimal in aqueous solution. Na⁺ and Cl^- ions did not negatively affect the adsorption process, while humic acid (HA) slightly decreased the capacity. The equilibrium time was 40 sec, and the maximum adsorption capacity reached 282.49 mg/g at 298 K. The removal process was endothermic and spontaneous, and the copolymer could maintain its porous structure and consistent performance after regeneration by treatment with alkali. Moreover, to further assess the practical applicability of the material, the adsorption performance towards 2,4-DCP in river water was also investigated. This paper demonstrated that the PI-b-ARPOP can be an efficient and practical adsorbent to remove chlorophenols from aqueous solution.

Response of soil enzymes, functional bacterial groups, and microbial communities exposed to sudan I-IV

As an important type of typical synthetic azo dyes, the use of sudan I-IV dyes has been of concern worldwide because of their wide applications and illegal addition into various foodstuffs, potentially resulting in water and soil pollution and having adverse effects on human health and ecosystems. However, to date, little has been reported regarding the environmental levels of these dyes and the risks that they pose to human health and ecosystems. Understanding the responses of soil enzymes, functional groups of bacteria and microbial communities to sudan dyes is of great importance to reveal their effect on the soil environment. In this study, we performed a toxicological study on the specific and overall effects of sudan I-IV dyes on the activity of soil enzymes including catalase, urease, and alkaline phosphatase after a 2- and 7-day exposure, functional groups of soil bacteria including nitrogen-fixing, ammonia-oxidizing, and denitrifying bacteria on day 14, and the structure and diversity of soil microbial community compositions on day 30. The results showed that sudan I-IV affected the activity of the soil enzymes, the abundance of the bacterium functional groups, and the structure and diversity of microbial community compositions, and the effects varied by sudan dyes I-IV, the exposure concentration, and the exposure time.

Fabrication of NiFe2O4 magnetic nanoparticles loaded on activated carbon as novel nanoadsorbent for Direct Red 31 and Direct Blue 78 adsorption

In this research, magnetic nickel ferrite NiFe₂O₄/hazelnut-shell-based activated carbon (NiFe₂O₄/AC) was used to eliminate anionic dyes (Direct Red 31(DR31) and Direct Blue 78 (DB78)) from aqueous solution. The morphological, structural, particle size and surface charge properties of as-prepared nanoadsorbent were characterized. TEM (Transmission electron microscopy) images revealed that the size of NiFe₂O₄ particles in the structure of AC was in the range of 8-12 nm, which is compatible with the results obtained by the analysis of DLS (Dynamic light scattering). The results of the BET (Brunauer-Emmett-Teller) analysis indicated that the surface area, the pore volume and average pore diameters of the NiFe₂O₄ were 288 m²/g, 0.3338 cm³/g and 5.05nm, respectively. The as-prepared nanocomposite showed excellent adsorption capacity for DR31 and DB78 dyes with the highest adsorption capacity obtained at pH=2.0 and rapid dye adsorption equilibrium attained after 20 and 25 min for DR31 and DB78, respectively. The equilibrium study showed the maximum adsorption capacity (q_max) of 299.67 mg/g and 209.13 mg/g for DR31 and DB78, respectively. In addition, thermodynamic study revealed the endothermic and spontaneous nature of adsorption process. The adsorption of DR31 and DB78 onto the NiFe₂O₄/AC is a physisorption process, during which electrostatic adsorption was the main driving force.

Adsorption behavior of Sudan I-IV on a coastal soil and their forecasted biogeochemical cycles

Sudan I-IV as synthetic azo dyes have been concerned worldwide and ever caused a panic on food safety because of illegal addition into foodstuffs. In the past decades, various methods are being developed to identify and determine Sudan dyes in foodstuffs. However, relevant studies about their biogeochemical behaviors and potential environmental effects are rarely reported, although it is of great importance and necessity accounting for their potential environmental contamination from various sources. In this work, the experimental studies on adsorption behavior of Sudan I-IV acting on soil (10, 25, 50, 75, and 100 mg/L) were carried out, and their transport in soil compartments and between soil-water, and air-soil interfaces were discussed. Results showed that the amount of Sudan I-IV adsorbed on soil increased accordingly with the increasing concentration of Sudan dyes in aqueous solution, and Sudan II and IV were more likely adsorbed on the tested soils than Sudan I and III based on their maximum adsorption amount. However, for Sudan I, III, and IV, in some high concentrations (under the treatment of 75 mg/L for Sudan III, 100 mg/L for Sudan I and IV), the adsorption was significantly increased, and then came back to the "normal" level (under the treatment of 100 mg/L for Sudan III). It is expected that relevant researches on their biogeochemical behaviors in soil compartments, and between soil-water and air-soil interfaces would be concerned and addressed.

Synthesis of Fe-doped Bi2O3 nanocatalyst and its sonophotocatalytic activity on synthetic dye and real textile wastewater

The catalysts such as Fe, Bi₂O₃, and Fe-doped Bi₂O₃ were synthesized for the sonophotocatalytic treatment of synthetic dye and real textile wastewater. The resultant catalysts were characterized for its size and uniform shape using x-ray diffractogram (XRD) and scanning electron microscopy (SEM) which signified the nanorod shape formed Bi₂O₃. The higher ultraviolet light absorbance capacity of the catalysts was also evident using diffuse reflectance spectroscopy (DRS). Initially, the effect of conventional parameters such as initial pH, gas bubbling (argon, oxygen, air and nitrogen) and oxidant addition (H₂O₂ and peroxymonosulfate) in the presence of sonolysis (22 and 37 kHz frequency) and photolysis (UV-C light) on 10 ppm Basic Brown 1 dye was studied. The results showed that highest decolorization of 62 % was attained for 3 g/L peroxymonosulfate under 37 kHz frequency sonolysis treatment. Secondly, with the catalyst study, highest of 46 % dye color removal was obtained with 4 g/L Fe under 37 kHz frequency sonolysis treatment. The sonophotocatalytic treatment of dye with Fe-doped Bi₂O₃ catalyst in combination with peroxymonosulfate showed highest color removal of 99 %. Finally, the sonophotocatalytic treatment of real textile wastewater in the presence of 3 g/L Fe-doped Bi₂O₃ and 6 g/L peroxymonosulfate reduced the total organic carbon (TOC) and chemical oxygen demand (COD) level to 77 and 91 %, respectively, in 180 min. The reported treatment process was found to treat the synthetic dye and real textile wastewater effectively.

Fabrication of highly hydrophobic organic-inorganic hybrid magnetic polysulfone microcapsules: A lab-scale feasibility study for removal of oil and organic dyes from environmental aqueous samples

In this work, three kinds of organic-inorganic hybrid materials (vinyl benzene linear polymer modified SBA-15, attapulgite and halloysite nanotubes) in the shape of powder and the corresponding magnetic polysulfone microcapsules were developed for removal of oil and dyes from environmental aqueous samples, respectively. As determined from the oil and dye adsorption studies, the developed magnetic polysulfone microcapsules exhibited high adsorption capacity of 13.8-17.3g/g for oil. The prepared functionalized materials and the corresponding microcapsules can remove 85.0-91.6% and 81.8-87.8% Sudan I in 80 min and 7.6h, respectively. The results showed a significant improvement in their adsorption capacities and removal efficiencies compared to the parent matrices, indicating that the introducing of the vinyl benzene linear polymer was a major factor in the removal of the hydrophobic pollutants. At the same time, the adsorption capacity for the investigated pollutants also depended on the textural feature of matrix itself. In view of the utilization of low-cost clay minerals (attapulgite and halloysite nanotubes), these proposed functionalized materials and the corresponding magnetic polysulfone microcapsules had a great promise to be used as an efficient sorbent for removal of pollutants from environmental aqueous samples.

Fe3O4@P(DVB/MAA)/Pd composite microspheres: preparation and catalytic degradation performance

Fe₃O₄@P(DVB/MAA)/Pd composite microspheres were synthesized with a combination of coating and loading processes using Fe₃O₄ nanoparticles as a core.