Synthesis and characterization of GTMAC grafted chitosan membranes for the dehydration of low water content isopropanol by pervaporation

Engineering Wet-Resistant and Osteogenic Nanocomposite Adhesive to Control Bleeding and Infection after Median Sternotomy

Median sternotomy surgery stands as one of the prevailing strategies in cardiac surgery. In this study, the cutting-edge bone adhesive is designed, inspired by the impressive adhesive properties found in mussels and sandcastle worms. This work has created an osteogenic nanocomposite coacervate adhesive by integrating a cellulose-polyphosphodopamide interpenetrating network, quaternized chitosan, and zinc, gallium-doped hydroxyapatite nanoparticles. This adhesive is characterized by robust catechol-metal coordination which effectively adheres to both hard and soft tissues with a maximum adhesive strength of 900 ± 38 kPa on the sheep sternum bone, surpassing that of commercial bone adhesives. The release of zinc and gallium cations from nanocomposite adhesives and quaternized chitosan matrix imparts remarkable antibacterial properties and promotes rapid blood coagulation, in vitro and ex vivo. It is also proved that this nanocomposite adhesive exhibits significant in vitro bioactivity, stable degradability, biocompatibility, and osteogenic ability. Furthermore, the capacity of nanocomposite coacervate to adhere to bone tissue and support osteogenesis contributes to the successful healing of a sternum bone defect in a rabbit model in vivo. In summary, these nanocomposite coacervate adhesives with promising characteristics are expected to provide solutions to clinical issues faced during median sternotomy surgery.

Synthesis, characterization and application of chitosan functionalized and functional graphene oxide membranes for desalination of water by pervaporation

The use of graphene sheets in water treatment is increasing due to its adsorption capacity, reactivity, catalytic action and surface area. The challenges linked to wastewater treatment are vast due to the constant influx of various pollutants. Can the challenges of water desalination and purification be encountered by graphene-based composites and membranes?.The current work describes the synthesis of graphene oxide (GO) using modified Hummers' method. GO was functionalized with chitosan and used as adsorbents. On the other hand, it was reported that the surface of thin-film-composite (TFC) polyamide membranes was modified in order to desalinate highly saline water using pervaporation. The findings showed that GO synthesized by modified Hummers' method has a greater capacity for the adsorption of sodium ion and have better regeneration performance. Functionalization with chitosan increased adsorption capacity from 680.2 to 740.5 mg/g at the initial concentration of 45,000 mg/l of Na+ ions. On the other hand, modification in membrane comprises the chlorine treatment of surface of polyamide membrane. Layer-by-layer (LbL) deposition of positively charged polyethyleneimine (PEI) and negatively charged graphene oxide (GO) was followed. The PEI/GO LbL membrane's pure water flux was twice as high as compare to the original membrane. The synthesized membrane was tested against the aqueous solutions containing Na2SO4, MgSO4, NaCl and MgCl2 salts for their desalination. At different concentrations, a water flux of 8.9 kg/m2h with a huge salt rejection (>99.9%) was attained for every tested salt. It was observed that CS functionalized GO and GO membrane showed higher adsorption capacity and improved regeneration performance can be measured as an operational and active adsorbent for sea water desalination.

Construction of Janus structures on thin silk fabrics via misting for wet-thermal comfort and antimicrobial activity

Owing to their small fiber diameter (10-15 μm), silk fabrics are always thin (32-90 g m-2). Therefore, construction of the Janus surfaces of silk fabrics that possess excellent multifunctionality remains a formidable challenge. Herein, first, silk fabrics were grafted using glycidyltrimethylammonium chloride to form a superhydrophilic surface (G-side). Then, a unilateral hydrophobic surface (O-side) was readily fabricated by mist coating octadecyltrichlorosilane-functionalized SiO2 nanoparticles (NPs) to produce hierarchical surface textures. To prevent NP penetration from the G-side to the O-side, a "fireproof isolation" method was employed. Consequently, Janus silk fabrics (JanSFs) bearing asymmetric wettability were prepared, and their wetting gradient could be conveniently regulated. With the mist time ranging from 4 to 7 min, the unidirectional transport index and efficiency of the unidirectional water transport increased and decreased by 13.2 and 10.4 times, respectively. Sweat could be effectively drained away from human skin to ensure that the skin was dry and comfortable. Compared with the surface temperature of the raw fabric, the raw fabric of JanSFs increased by 2.7 °C. Furthermore, the breathability of JanSF was negligibly affected, and the outer O-side of the JanSF showed substantial antibacterial activity. This study is important for designing JanSFs that exhibit unidirectional water transport.

Engineering pH-sensitive erodible chitosan hydrogel composite containing bacteriophage: An interplay between hydrogel and bacteriophage against Staphylococcus aureus

Encapsulation of phages represents a key approach for improving phage stability and controlling phage delivery dosage. The hydrogel made from positively charged quaternized chitosan (QCS) and multivalent crosslinker, aldehyde-modified poly(xylitol sebacate)-co-poly(ethylene glycol) (APP) was introduced for the first time for drug (phage 44AHJD) delivery. The freeze-thawing (FT) treatment enhanced the porous structure and the stress resistance of native hydrogel with increased compression stress (stiffness) from 10 to 20 kPa. The stiffness of the phage-loaded hydrogel (FTP) was suitable for the proper release of phage particles and polymer chains, both working synergistically against bacterial growth. The FTP followed the Korsmeyer-Peppas model's anomalous diffusion of phage particles at different temperatures (30-45 °C) and pH (6.6-8.5) conditions. FTP was sensitive to pH, which released more phage particles at pH-neutral conditions, while the release under acidic and alkaline conditions was more based on gel degradation. The high biocompatibility of FTP hydrogel at its working concentration of 30 mg mL-1 was demonstrated through a hemolysis ratio of <2 %. Sixty percent of the total encapsulated phages and 6 mg mL-1 of hydrogel debris were released after 10 h of hydrogel submerge treatment, which can fight the growing bacteria and the emergence of phage-resistant bacteria.

Review: chitosan-based biopolymers for anion-exchange membrane fuel cell application

Chitosan (CS)-based anion exchange membranes (AEMs) have gained significant attention in fuel cell applications owing to their numerous benefits, such as environmental friendliness, flexibility for structural alteration, and improved mechanical, thermal and chemical durability. This study aims to enhance the cell performance of CS-based AEMs by addressing key factors including mechanical stability, ionic conductivity, water absorption and expansion rate. While previous reviews have predominantly focused on CS as a proton-conducting membrane, the present mini-review highlights the advancements of CS-based AEMs. Furthermore, the study investigates the stability of cationic head groups grafted to CS through simulations. Understanding the chemical properties of CS, including the behaviour of grafted head groups, provides valuable insights into the membrane's overall stability and performance. Additionally, the study mentions the potential of modern cellulose membranes for alkaline environments as promising biopolymers. While the primary focus is on CS-based AEMs, the inclusion of cellulose membranes underscores the broader exploration of biopolymer materials for fuel cell applications.

Cationic modification of cellulose as a sustainable and recyclable adsorbent for anionic dyes

There is a dire need to find an efficient, cost-effective, sustainable, and environment-friendly adsorbent for the removal of anionic pollutants such as dyes from waste effluent. In this work, a cellulose-based cationic adsorbent was designed and utilized for methyl orange and reactive black 5 anionic dyes adsorption from an aqueous medium. Solid-state nuclear magnetic resonance spectroscopy (NMR) revealed the successful modification of cellulose fibers, and dynamic light scattering (DLS) evaluations showed the levels of charge densities. Furthermore, various models for adsorption equilibrium isotherm were utilized to understand the adsorbent characteristics, with the Freundlich isotherm model providing an excellent fit for the experimental results. The modelled maximum adsorption capacity was as much as 1010 mg/g for both model dyes. The dye adsorption was also confirmed using EDX. It was noted that the dyes were chemically adsorbed through the ionic interaction that can be reversed using sodium chloride solution. Overall, the cationized cellulose is inexpensive, environment-friendly, nature-driven, and recyclable making it an appealing adsorbent feasible for the dye removal from textile wastewater effluent.

Novel Polyelectrolyte Complex Membranes Containing Carboxymethyl Cellulose-Gelatin for Pervaporation Dehydration of Azeotropic Bioethanol for Biofuel

Polyelectrolyte complex membranes (PECMs) were prepared by combining sodium carboxymethyl cellulose (NaCMC) and gelatin (Ge) with variations in the Ge content in the NaCMC matrix. Characterization methods, such as infrared spectroscopy (FTIR), wide-angle X-ray diffraction (WAXD), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), contact angle analysis (CA), and universal testing machines (UTM) were used to investigate the physicochemical studies of the prepared membranes. The pervaporation characteristics of membranes with Ge content were investigated using an azeotropic mixture of water and bioethanol. The obtained data revealed that the membrane with 15 mass% of Ge (M-3) showed a maximum flux of 7.8403 × 10^-2 kg/m²·h with separation selectivity of 2917 at 30 °C. In particular, the total and water flux of PECMs are shown as very close to each other indicating that the fabricated membranes could be employed to successfully break the azeotropic point of water-bioethanol mixtures. Using temperature-dependent permeation and diffusion data, the Arrhenius activation parameters were calculated, and the obtained values of water permeation (E_pw) were considerably smaller than bioethanol permeation (E_pE). Developed membranes showed the positive heat of sorption (ΔH_s), suggesting that Henry's sorption mode is predominant.

A Brief Review of Poly(Vinyl Alcohol)-Based Anion Exchange Membranes for Alkaline Fuel Cells

Anion exchange membrane fuel cells have unique advantages and are thus gaining increasing attention. Poly(vinyl alcohol) (PVA) is one of the potential polymers for the development of anion exchange membranes. This review provides recent studies on PVA-based membranes as alternative anion exchange membranes for alkaline fuel cells. The development of anion exchange membranes in general, including the types, materials, and preparation of anion exchange membranes in the last years, are discussed. The performances and characteristics of recently reported PVA-based membranes are highlighted, including hydroxide conductivity, water uptake, swelling degree, tensile strength, and fuel permeabilities. Finally, some challenging issues and perspectives for the future study of anion exchange membranes are discussed.

Fabrication and Characterization of Poly (Vinyl Alcohol)-Chitosan-Capped Silver Nanoparticle Hybrid Membranes for Pervaporation Dehydration of Ethanol

Chitosan-capped silver nanoparticle (CS-capped AgNPs)-incorporated Poly(vinyl alcohol) (PVA) hybrid membranes were prepared by a solution-casting technique for ethanol dehydration via pervaporation. The incorporation of CS-capped AgNPs into the PVA membrane and its influence on membrane properties and pervaporation-separation process of azeotropic water/ethanol mixture was studied. The addition of CS-capped AgNPs into the PVA membrane reduced the crystallinity, thereby increasing the hydrophilicity and swelling degree of the hybrid membrane, supported by contact angle (CA) analyzer and swelling degree experiments, respectively. Fourier transform infrared spectroscopy (FTIR) demonstrated the formation of polymeric matrix between PVA and CS and also the binding of AgNPs onto the functional group of CS and PVA, which was also reflected in the microstructure images demonstrated by scanning electron microscopy (SEM) and by 2θ angle of wide-angle X-ray diffraction (WAXD). The effect of CS-capped AgNPs on the thermal stability of the hybrid membrane was demonstrated by differential scanning calorimetry (DSC) and thermogravimetric analyzer (TGA). These characteristics of the hybrid membrane positively impact the efficiency of the dehydration of ethanol, as indicated by pervaporation experiments. The best performances in total flux (12.40 ± 0.20 × 10⁻² kg/m² h) and selectivity (3612.33 ± 6.03) at 30 °C were shown for CS-capped AgNPs PVA hybrid membrane containing 2 wt.% CS-capped AgNPs (M-4). This confirms that the developed hybrid membranes can be efficiently used to separate water from azeotropic aqueous ethanol.

Preparation and applications of hydrophilic quaternary ammonium salt type polymeric antistatic agents

A novel ammonium salt type polymeric antistatic agent (PDSH) was synthesized from methacrylatoethyl trimethyl ammonium chloride, styrene, and 2-hydroxyethyl methacrylate via radical polymerization. Antistatic poly(acrylonitrile-co-butadiene-co-styrene) (ABS)/PDSH composites were prepared by blending PDSH with ABS resin. The results showed that the surface resistivity of ABS/PDSH composites with PDSH addition decreased significantly. The surface resistivity of ABS/PDSH composites containing 20 wt% PDSH was around 109–1010 Ω, which was about 106 times lower than that of neat ABS. At the same time, ABS/PDSH composites had good thermal stability and hydrophilicity. The PDSH was more uniformly dispersed within the ABS resin and had less influence on the mechanical properties of the composites. With the demonstrated properties, the prepared copolymer PDSH can serve as a well-integrated antistatic agent and display potential for the antistatic treatment of ABS.

Efficient removal of anionic, cationic textile dyes and salt mixture using a novel CS/MIL-100 (Fe) based nanofiltration membrane

The purification of hazardous textile dyeing wastewater has exhibited many challenges because it consists of a complex mixture, including dyestuff, additives, and salts. It is necessary to fabricate membranes with enhanced permeability, fouling resistance, stability, and superior dyes and salts removal from wastewater. Incorporating a highly water stable metal-organic framework (MOFs) into membranes would meet the requirements for the efficient purification of textile wastewater. In this study, nanofiltration (NF) membranes are fabricated by incorporating MIL-100 (Fe) into the chitosan (CS) through film casting technique. The effect of MIL-100 (Fe) loadings on chitosan characterized by FT-IR, XRD, contact angle measurement, FESEM-EDS, XPS, zeta potential, and surface roughness analysis. The membrane characterization confirmed the enhanced surface roughness, pore size, surface charge, and hydrophilicity. The CS/MIL-100 (Fe) membrane exhibited an improved pure water flux from 5 to 52 L/m²h as well as 99% rejection efficiency for cationic methylene blue (MB) and anionic methyl orange (MO). We obtained the rejection efficiency trend for the MB mixed salts in the order of MgSO₄ (Mg²⁺ - 51.6%, SO₄^2- - 52.5%) > Na₂SO₄ (Na⁺ - 26.3%, SO₄^2- - 29.3%) > CaCl₂ (Ca²⁺ - 21.4%, Cl^- - 23.8%) > NaCl (Na⁺ - 16.8%, Cl^- - 19.2%). In addition, the CS/MIL-100 (Fe) composite membrane showed excellent rejection efficiency and antifouling performances with high recycling stability. These stunning results evidenced that the CS/MIL-100 (Fe) nanofiltration membrane is a promising candidate for removing toxic pollutants in the textile dyeing wastewater.

Development and Characterization of Biocompatible Membranes from Natural Chitosan and Gelatin for Pervaporative Separation of Water-Isopropanol Mixture

Natural polymers have attracted a lot of interest in researchers of late as they are environmentally friendly, biocompatible, and possess excellent characters. Membranes forming natural polymers have provided a whole new dimension to the separation technology. In this work, chitosan-gelatin blend membranes were fabricated using chitosan as the base and varying the amount of gelatin. Transport, mechanical, and surface characteristics of the fabricated membranes were examined in detail by means of the characterizing techniques such as Fourier transform infrared spectroscopy, differential scanning colorimetry, wide angle X-ray diffraction, scanning electron microscope, and thermogravimetric analysis. In order to analyze the water affinity of the developed blend chitosan-gelatin membranes, the percentage degree of swelling was examined. Out of the fabricated membranes, the membrane loaded with 15 mass% of gelatin exhibited the better pervaporation performance with a pervaporation separation index value of 266 at 30 °C for the solution containing 10% in terms of the mass of water, which is the highest among the contemporary membranes. All the fabricated membranes were stable during the pervaporation experiments, and permeation flux of water for the fabricated membranes was dominant in the overall total permeation flux, signifying that the developed membranes could be chosen for efficient separation of water-isopropanol mixture on a larger scale.

Underwater suspended bifunctionalized polyethyleneimine-based sponge for selective removal of anionic pollutants from aqueous solution

Highly selective and efficient removal of ionic pollutants, including ionic organic compounds and heavy metal ions from water, is still a huge challenge due to the complex nature of polluted water. To meet this challenge, we presented the synthesis of bifunctionalized polyethyleneimine-based sponges through cryo-polymerization via BDDE as the crosslinker followed by bifunctional modification with glycidyl trimethylammonium chloride (GTAC) and phenyl glycidyl ether (PGE), which simultaneously afford quaternary ammonium cation (strongly basic and hydrophilic) and phenyl (hydrophobic) functionalities, respectively. As a result, a hybrid hydrophilic-hydrophobic sponge is generated that could stably be suspended underwater due to the co-operative effect of the water-absorbing hydrophilic domain and the hydrophobic domain generating buoyancy. The quaternized and phenyl-functionalized PEI-based sponge (S_QP-PEI) demonstrated highly selective and efficient removal of anionic pollutants from water, including diclofenac sodium (DIC), methyl orange (MO) and chromium (Cr(VI)) with co-existing interferences. The Langmuir isotherms revealed the maximum adsorption capacities of 342.7 mg/g, 491.9 mg/g, and 242.7 mg/g for DIC, MO, and Cr(VI), respectively. The studies of adsorption mechanism suggested that the bifunctional S_QP-PEI sponge indeed afford both strong anion-exchange interaction and π-π interaction toward organic pollutants DIC and MO, and the strong anion-exchange interaction can be the dominated adsorption mechanism for anionic DIC, MO and Cr(VI) species. The suspended S_QP-PEI also demonstrated excellent reusability, which shows the potential of S_QP-PEI for real applications.

Fabrication and Physicochemical Study of B2SA-Grafted Poly(vinyl Alcohol)-Graphene Hybrid Membranes for Dehydration of Bioethanol by Pervaporation

Tetraethylorthosilicate (TEOS)-crosslinked poly(vinyl alcohol) (PVA) solution was prepared and treated with benzaldehyde 2 sulphonic sodium salt acid (B2SA) for sulfonation. Different contents of graphene were incorporated into B2SA-grafted PVA-TEOS hybrid membrane to improve the membrane stability, mechanical strength, and overall pervaporation performance of the membranes. Membranes were fabricated using the casting technique. Developed membranes were then analyzed for their physicochemical changes by means of Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), scanning electron microscope (SEM), wide-angle X-ray diffraction (WAXD), thermogravimetric analysis (TGA), contact angle analysis (CA), and mechanical strength. The lower d-spacing value observed in WAXD was evidence for the decreased inter-chain distance between the polymer chains. DSC exhibited the enhanced thermal stability of the developed membranes compared to the plane PVA membrane with enhancement in Tg value (106 °C), which was well above the pervaporation experimental temperature. Incorporation of graphene induced higher mechanical strength to the fabricated membranes. Further, the membranes were tested for the pervaporation separation of bioethanol. All the membranes were stable throughout the pervaporation studies, with M-2 G showing the total permeation flux of 11.66 × 10-2 kg/(m2 h) at 30 °C.

Crosslinked Nanocomposite Sodium Alginate-Based Membranes with Titanium Dioxide for the Dehydration of Isopropanol by Pervaporation

Sodium alginate (NaAlg) based membranes were prepared using a solution technique, crosslinked with poly(styrene sulfonic acid-co-maleic acid) (PSSA-co-MA). Subsequently, the membranes were modified by the incorporation of 0, 10, 20, 30 and 40% w/w of titanium dioxide with respect to sodium alginate. The membranes thus obtained were designated as M, M-1, M-2, M-3 and M-4, respectively. An equilibrium swelling experiment was performed using different compositions of the water and isopropanol mixtures. Subsequently, we used a pervaporation cell fitted with each membrane in order to evaluate the extent of the pervaporation dehydration of isopropanol. Among the membranes studied, the membranes containing 40 mass% of titanium dioxide exhibited the highest separation factor(α) of 24,092, with a flux(J) of 18.61 × 10-2 kg/m2∙h at 30 °C for 10 mass% w/w of water in the feed. The total flux and the flux of water were found to overlap with each other, indicating that these membranes can be effectively used to break the azeotropic point of water-isopropanol mixtures. The results clearly indicate that these nanocomposite membranes exhibit an excellent performance in the dehydration of isopropanol. The activation energy values obtained for the water permeation were significantly lower than those of the isopropanol permeation, underlining that these membranes have a high separation ability for the water-isopropanol system. The estimated activation energies for total permeation (EP) and total diffusion (ED) values ranged between 10.60 kJ∙mol-1 and 3.96 kJ∙mol-1, and 10.76 kJ∙mol-1 and 4.29 kJ∙mol-1, respectively. The negative change in the enthalpy values for all the membranes indicates that sorption was mainly dominated by Langmuir's mode of sorption.

High-performance pervaporation chitosan-based membranes: new insights and perspectives

Today, the need of replacing synthetic polymers in the membrane preparation for diverse pervaporation (PV) applications has been recognized collectively and scientifically. Chitosan (CS), a bio-polymer, has been studied and proposed to achieve this goal especially in specific azeotropic water-organic, organic-water, and organic-organic separations, as well as in assisting specific processes (e.g. seawater desalination and chemical reactions). Different concepts of CS-based membranes have been developed, which include material blending and composite and mixed matrix membranes which have been tested for different separations. Hereby, the goal of this review is to provide a critical overview of the ongoing CS-based membrane developments, paying a special attention to the most relevant findings and results in the field. Furthermore, future trends of CS-based membranes in PV technology are presented, as well as concluding remarks and suggested strategies for the new scientist in the field.

Novel Composite Membranes Based on Chitosan Copolymers with Polyacrylonitrile and Polystyrene: Physicochemical Properties and Application for Pervaporation Dehydration of Tetrahydrofuran

Pervaporation has been applied for tetrahydrofuran (THF) dehydration with novel composite membranes advanced by a thin selective layer composed of chitosan (CS) modified by copolymerization with vinyl monomers, acrylonitrile (AN) and styrene, in order to improve the chemical and mechanical stability of CS-based membranes. Composite membranes were developed by depositing a thin selective layer composed of CS copolymers onto a commercially-available porous support based on aromatic polysulfonamide (UPM-20^®). The topography and morphology of the obtained materials were studied by atomic force microscopy (AFM), scanning electron microscopy (SEM) and X-ray diffraction analysis (XRD). Thermal properties and stability were determined by coupled evolved gas analysis (EGA-MS). Transport properties were estimated in pervaporation dehydration of THF. The effect of operating parameters for the pervaporation dehydration of THF such as feed compositions and temperatures (295, 308 and 323 K) was evaluated. It was shown that CS modification with different vinyl monomers led to a difference in physical and transport properties. The composite membrane with the thin selective layer based on CS-PAN copolymer demonstrated optimal transport properties and exhibited the highest water content in the permeate with a reasonably high permeation flux.

Ag-exchanged NaY zeolite introduced polyvinyl alcohol/polyacrylic acid mixed matrix membrane for pervaporation separation of water/isopropanol mixture

Ag-exchanged NaY zeolite (Ag-NaZ) particles were prepared by ion exchange and introduced to a polyvinyl alcohol (PVA) membrane cross-linked with polyacrylic acid (PAA) for the pervaporation dehydration of an isopropanol (IPA) aqueous mixture. The Ag-exchanged NaY zeolite particles were characterized by FE-SEM, EDS, BET, and XRD studies. The prepared Ag-NaZ-loaded PVA/PAA composite membrane was characterized by FE-SEM, XRD, a swelling study, and contact angle measurements. Pervaporation characteristics were investigated in terms of Ag-NaZ concentrations within PVA/PAA membranes using diverse feed solution conditions. The preferential sorption of IPA/water mixtures for Ag-NaZ-introduced membranes were also determined by calculating the apparent activation energies of IPA and water permeation, respectively. As a result, flux and selectivity increased with the Ag-NaZ concentration to 5 wt% in the membrane. Optimum pervaporation performance was observed in a 5 wt% Ag-NaZ-incorporated membrane with a flux equal to 0.084 kg m-2 h-1 and a separation factor of 2717.9 at 40 °C from an 80 wt% IPA aqueous feed solution.

Preparation and Characterization of Facilitated Transport Membranes Composed of Chitosan-Styrene and Chitosan-Acrylonitrile Copolymers Modified by Methylimidazolium Based Ionic Liquids for CO₂ Separation from CH₄ and N₂

CO₂ separation was found to be facilitated by transport membranes based on novel chitosan (CS)-poly(styrene) (PS) and chitosan (CS)-poly(acrylonitrile) (PAN) copolymer matrices doped with methylimidazolium based ionic liquids: [bmim][BF₄], [bmim][PF₆], and [bmim][Tf₂N] (IL). CS plays the role of biodegradable film former and selectivity promoter. Copolymers were prepared implementing the latest achievements in radical copolymerization with chosen monomers, which enabled the achievement of outstanding mechanical strength values for the CS-based membranes (75-104 MPa for CS-PAN and 69-75 MPa for CS-PS). Ionic liquid (IL) doping affected the surface and mechanical properties of the membranes as well as the gas separation properties. The highest CO₂ permeability 400 Barrers belongs to CS-b-PS/[bmim][BF₄]. The highest selectivity α (CO₂/N₂) = 15.5 was achieved for CS-b-PAN/[bmim][BF₄]. The operational temperature of the membranes is under 220 °C.

Development of composite anion-exchange membranes using poly(vinyl alcohol) and silica precursor for pervaporation separation of water–isopropanol mixtures

Composite anion-exchange membranes (AEMs) were prepared using sol–gel techniques with poly(vinyl alcohol) and anion-exchange silica precursor (AESP). Among the composite AEMs, the membrane containing 4 mass% of AESP (M-4) exhibited the excellent pervaporation performance.