Sensitive 1,2-dichlorobenzene chemi-sensor development based on solvothermally prepared FeO/CdO nanocubes for environmental safety

AIEE-active dichlorobenzene and chlorobenzene ratiometric fluorescent probe based on [2.2]paracyclophane

Two AIEE-active [2.2]paracyclophanyl-based diester and monoester (1a and 1b) were facilely synthesized by one-pot method and applied as ratiometric fluorescent probe to detect dichlorobenzene (DCB) and chlorobenzene (CB). Compared with compound 1b, 1a exhibits high sensitivity and low detection limits for DCB and CB in dichloromethane (DCM), particularly, the detection sensitivities for ortho-dichlorobenzene (o-DCB), meta-dichlorobenzene (m-DCB) and chlorobenzene can be modulated by AIEE behavior with lower detection limits of 23.64, 56.27, and 5.92 ppm, respectively in THF/H2O mixed solutions with water fraction (fw) of 70 % due to the formation of aggregation-state. The X-ray structure analysis, theoretical calculations and photophysical properties in different solvents were investigated to reveal the distinctive photophysical behaviors of 1a and 1b. The facile synthesis, X-ray structure, AIEE modulated sensing properties for o-DCB, m-DCB, and CB in DCM and THF/H2O mixed solutions make 1a potential application as fluorescent probe for trace DCB and CB detection in drinking water.

Development of an efficient electrochemical sensing platform based on ter-poly(luminol-o-anisidine-o-toluidine)/ZnO/GNPs nanocomposites for the detection of antimony (Sb3+) ions

A poly(luminol-o-anisidine-o-toluidine) terpolymer was synthesized, characterized, and modified with GNPs and ZnO NPs. The nanocomposites were then examined for their electroactivity and potential use as cationic electrochemical sensors for detecting Sb3+ ions in phosphate buffer on the surface of a glassy carbon electrode (GCE). Among the different compositions and the terpolymer, the GCE adapted with the PLAT/ZnO/GNPs-5% nanocomposite displayed the highest current response. The fabricated nanocomposite sensor exhibited high sensitivity, with a value of 21.4177 μA μM-1 cm-2, and a low detection limit of 95.42 pM. The analytical performance of the sensor was evaluated over the linear dynamic range (LDR) of 0.1 nM to 0.01 mM. The proposed sensor is effective in detecting and measuring carcinogenic Sb3+ ions in real environmental samples using an electrochemical approach, making it a promising tool for environmental monitoring.

Microwave Sensors for In Situ Monitoring of Trace Metals in Polluted Water

Thousands of pollutants are threatening our water supply, putting at risk human and environmental health. Between them, trace metals are of significant concern, due to their high toxicity at low concentrations. Abandoned mining areas are globally one of the major sources of toxic metals. Nowadays, no method can guarantee an immediate response for quantifying these pollutants. In this work, a novel technique based on microwave spectroscopy and planar sensors for in situ real-time monitoring of water quality is described. The sensors were developed to directly probe water samples, and in situ trial measurements were performed in freshwater in four polluted mining areas in the UK. Planar microwave sensors were able to detect the water pollution level with an immediate response specifically depicted at three resonant peaks in the GHz range. To the authors’ best knowledge, this is the first time that planar microwave sensors were tested in situ, demonstrating the ability to use this method for classifying more and less polluted water using a multiple-peak approach.

Surface-tuned hierarchical ɤ-Fe2O3-N-rGO nanohydrogel for efficient catalytic removal and electrochemical sensing of toxic nitro compounds

4- Nitrophenol (4-NP) is a top rated hazardous environmental pollutant and secondary explosive chemicals. For the sake of ecology and environment safety, the catalytic reduction and detection of 4-NP is highly important. In this work, ɤ-Fe₂O₃-nitrogen doped rGO (ɤ-Fe₂O₃-N-rGO) nanohydrogel was synthesized by green hydrothermal method. The morphology and phase purity of prepared ɤ-Fe₂O₃-N-rGO nanohydrogel were confirmed by various analytical (SEM, TEM, XRD, and XPS) and electrochemical techniques. The morphological structure of ɤ-Fe₂O₃-N-rGO nanohydrogel confirmed that the nanocrystals are well covered over the 2D N-rGO layer. Further, ɤ-Fe₂O₃-N-rGO nanohydrogel was applied for the catalytic reduction and electrochemical detection of ecotoxic 4-NP. A low cost, ɤ-Fe₂O₃-N-rGO nanohydrogel displayed an excellent catalytic activity, high recyclability (>5 cycles) and high conversion efficiency of 4-NP to 4-Aminophenol (4-AP). In addition, ɤ-Fe₂O₃-N-rGO nanohydrogel modified GCE displayed a wide linear sensing range (0.1-1000 μM), and a low detection limit (LOD) of 0.1 μM with excellent sensitivity, high selectivity (<1.2%) and good stability (>4 weeks). The developed sensor electrode shows the low reduction potential of -0.3 V and -0.60 V for the determination of 4-NP. The proposed ɤ-Fe₂O₃-N-rGO nanohydrogel is promising catalyst for the detection and removal of toxic aromatic nitro compounds in real site applications.

An alternative electrochemical approach for toluene detection with ZnO/MgO/Cr2O3 nanofibers on a glassy carbon electrode for environmental monitoring

In situ fabrication of a sensitive electrochemical sensor using a wet-chemically prepared ternary ZnO/MgO/Cr2O3 nanofiber (NF)-decorated glassy carbon electrode (GCE) with Nafion adhesive was the approach of this study. The resultant NFs were characterized by various tools, such as powder X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectroscopy (EDS), Fourier transform infrared spectroscopy (FTIR), Brunauer-Emmett-Teller (BET) surface area analysis, and ultraviolet-visible spectroscopy (UV/Vis). The analytical parameters of the proposed toluene sensor were characterized as follows: good sensitivity (23.89 μA μM-1 cm-2), a lower limit of detection (LOD; 95.59 ± 1.5 pM), a limit of quantification (LOQ; 318.63 ± 2.0 pM), efficient response time (18 s), and the dynamic range (LDR) for toluene detection of 0.1 nM-0.01 mM. The real-time application of the sensor is to protect the environmental ecosystem, as well as the public health from the harmful effects of toluene. In an environmental application, the toluene sensor exhibited good reproducibility, robustness, LOD, LOQ, and good reliability, which are discussed in detail and compared to the literature.

An Electrochemical Approach for the Selective Detection of Cancer Metabolic Creatine Biomarker with Porous Nano-Formulated CMNO Materials Decorated Glassy Carbon Electrode

The facile wet-chemical technique was used to prepare the low-dimensional nano-formulated porous mixed metal oxide nanomaterials (CuO.Mn2O3.NiO; CMNO NMs) in an alkaline medium at low temperature. Detailed structural, morphological, crystalline, and functional characterization of CMNO NMs were performed by X-ray photoelectron spectroscopy (XPS), powder X-ray diffraction (XRD), ultraviolet-visible spectroscopy (UV-vis), Fourier-transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FESEM), and energy-dispersive X-ray spectroscopy (EDS) analyses. An efficient and selective creatine (CA) sensor probe was fabricated by using CMNO NMs decorated onto glassy carbon electrode (GCE) as CMNO NMs/GCE by using Nafion adhesive (5% suspension in ethanol). The relation of current versus the concentration of CA was plotted to draw a calibration curve of the CMNO NMs/GCE sensor probe, which was found to have a very linear value (r2 = 0.9995) over a large dynamic range (LDR: 0.1 nM~0.1 mM) for selective CA detection. The slope of LDR by considering the active surface area of GCE (0.0316 cm2) was applied to estimate the sensor sensitivity (14.6308 µAµM-1 cm-2). Moreover, the detection limit (21.63 ± 0.05 pM) of CMNO MNs modified GCE was calculated from the signal/noise (S/N) ratio at 3. As a CA sensor probe, it exhibited long-term stability, good reproducibility, and fast response time in the detection of CA by electrochemical approach. Therefore, this research technique is introduced as a promising platform to develop an efficient sensor probe for cancer metabolic biomarker by using nano-formulated mixed metal oxides for biochemical as well as biomedical research for the safety of health care fields.

Fabrication of an ultra-sensitive para-nitrophenol sensor based on facile Zn-doped Er2O3 nanocomposites via an electrochemical approach

In this study, a semiconductor-doped nanocomposite material (Zn-doped Er2O3 nano-composites) was prepared via a single-step wet-chemical technique at alkaline pH. Fourier-transform infrared spectroscopy (FT-IR), UV/Vis spectroscopy, photoluminescence spectroscopy (PL), field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectroscopy (XEDS), and X-ray powder diffractometry (XRD) were applied to determine the structural and morphological properties of the Zn-doped Er2O3 nanocomposite. A thin layer of aggregated Zn-doped Er2O3 nanocomposite was fabricated on the flat surface of a glassy carbon electrode (GCE) with 5% ethanolic Nafion as conducting coating binder for the development of a selective and sensitive p-nitrophenol (para-NP) capturing electrochemical probe for environmental remediation. After the fabrication of the sensor, a novel current-potential (I-V) electrochemical approach was applied to determine its selectivity and sensitivity together with all the necessary analytical parameters against para-NP. Moreover, the calibration plot was found to be linear with the linear dynamic range (LDR) of para-NP concentration. The limit of detection (LOD) at a signal-to-noise ratio of 3 (S/N ∼ 3) and sensitivity were also calculated to be 0.033 ± 0.002 pM and 28.481 × 10-2 μA μM-1 cm-2, respectively, based on the gradient of the calibration plot, and the limit of quantification (LOQ) was determined to be 0.11 ± 0.02 pM. This work demonstrates a well-known approach for the first time that can be used for the development of efficient electrochemical sensors. These sensors based on semiconductor doped nanomaterials embedded onto the GCE for the detection of toxic chemicals in an aqueous system as an environmental remediation. It can be further applied for the analysis of real environmental samples and in the healthcare field.

Facile and efficient 3-chlorophenol sensor development based on photolumenescent core-shell CdSe/ZnS quantum dots

Quantum dots (QDs) are semiconducting inorganic nanoparticles, tiny molecules of 2-10 nm sizes to strength the quantum confinements of electrons. The QDs are good enough to emit light onto electrons for exciting and returning to the ground state. Here, CdSe/ZnS core/shell QDs have been prepared and applied for electrochemical sensor development in this approach. Flat glassy carbon electrode (GCE) was coated with CdSe/ZnS QDs as very thin uniform layer to result of the selective and efficient sensor of 3-CP (3-chlorophenol). The significant analytical parameters were calculated from the calibration plot such as sensitivity (3.6392 µA µM-1 cm-2) and detection limit (26.09 ± 1.30 pM) with CdSe/ZnS/GCE sensor probe by electrochemical approach. The calibration curve was fitted with the regression co-efficient r2 = 0.9906 in the range of 0.1 nM ∼ 0.1 mM concentration, which denoted as linear dynamic range (LDR). Besides these, it was performed the reproducibility in short response time and successfully validated the fabricated sensor for 3-CP in the real environmental and extracted samples. It is introduced as a noble route to detect the environmental phenolic contaminants using CdSe/ZnS QDs modified sensor by electrochemical method for the safety of healthcare and environmental fields at broad scales.

Detection of 3,4-diaminotoluene based on Sr0.3Pb0.7TiO3/CoFe2O4 core/shell nanocomposite via an electrochemical approach

We reported a scalable sol–gel method for the preparation of Sr_0.3Pb_0.7TiO₃/CoFe₂O₄ core–shell magnetic nanocomposite with a finely controlled shell and evaluated its efficiency as an electrochemical sensor for the selective detection of 3,4-diaminotoluene.

A novel highly selective electrochemical chlorobenzene sensor based on ternary oxide RuO2/ZnO/TiO2 nanocomposites

A novel electrochemical (EC) chlorobenzene (CBZ) sensor was fabricated using a ternary oxide RuO₂/ZnO/TiO₂ nanocomposite (NC)-decorated glassy carbon electrode (GCE). The nanoparticles (NPs) were synthesized by a wet-chemical method and characterized by X-ray photoelectron spectroscopy (XPS), powder X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectroscopy (EDS), and ultraviolet-visible (UV-vis) spectroscopy. The synthesized RuO₂/ZnO/TiO₂ NC was layered as thin film on a GCE with Nafion (5% suspension in ethanol) adhesive, and the as-prepared sensor was subjected to CBZ analysis using an electrochemical approach. The calibration of the proposed CBZ sensor was executed with a linear relation of current versus concentration of CBZs known as the calibration curve. The sensitivity (32.02 μA μM⁻¹ cm⁻²) of the CBZ sensor was calculated from the slope of the calibration curve by considering the active surface area of the GCE (0.0316 cm²). The lower detection limit (LD; 98.70 ± 4.90 pM) was also calculated at a signal-to-noise ratio of 3. Besides these, the response current followed a linear relationship with the concentration of chlorobenzene and the linear dynamic range (LDR) was denoted in the range of 0.1 nM to 1.0 μM. Moreover, the CBZ sensor was found to exhibit good reproducibility, reliability, stability, and fast response time. Finally, the sensing mechanism was also discussed with the energy-band theory of ternary doped semiconductor materials. The sensing activity of the proposed sensor was significantly enhanced due to the combined result of depletion layer formation at the heterojunction of RuO₂/ZnO/TiO₂ NCs as well as the activity of RuO₂ NPs as oxidation catalysts. The proposed CBZ sensor probe based on ternary oxide RuO₂/ZnO/TiO₂ NCs was developed with significant analytical parameters for practical application in monitoring the environmental pollutants of CBZs for the safety of environmental fields on a large scale.

A novel electrochemical (EC) chlorobenzene (CBZ) sensor was fabricated using a ternary oxide RuO₂/ZnO/TiO₂ nanocomposite (NC)-decorated glassy carbon electrode (GCE).

3-Methoxyphenol chemical sensor fabrication with Ag2O/CB nanocomposites

The proposed chemical sensor based on Ag₂O/CB nanocomposites is developed by electrochemical approach for the detection of hazardous selective 3-methoxyphenol chemical sensor for the safety of the environment sector in a broad scale.

The fabrication of a chemical sensor with PANI-TiO2 nanocomposites

In this study, conjugated conducting polyaniline was fabricated onto titania nanoparticles (PANI-TiO₂ NPs) using a microwave-accelerated reaction system. The synthesized nanoparticles were characterized using the techniques of electron microscopy (e.g., FE-SEM and TEM), X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FT-IR), and ultraviolet-visible (UV-Vis) spectrometry. An ultrasensitive sensor using the electrochemical (I–V) approach was fabricated using a thin film of PANI-TiO₂ NPs on a glassy carbon electrode (GCE), and it was found to be selective towards 1,2-diaminobenzene (1,2-DAB) in a buffer phase. From current versus concentration studies, the calibration curve was plotted to estimate the sensor's analytical parameters. The highest sensitivity (19.8165 μA μM⁻¹ cm⁻²) and lowest detection limit (0.93 ± 0.05 pM) were obtained from the electrochemical assessment by applying a signal-to-noise ratio of 3. A linear calibration plot was attained over a large range of concentration (LDR: 1.0 pM to 0.01 mM). The selective 1,2-DAB sensor was found to be efficient and reproducible in performance, yielding significant results with a fast response time (12.0 s). Therefore, the overall results of the 1,2-DAB chemical sensor suggest that this detection approach might be an easy way to develop an efficient electrochemical sensor for the protection of the environment as well as for use in the healthcare field on a broad scale.

The conjugated conducting polyaniline was fabricated onto PANI-TiO₂ nanoparticles prepared by microwave-accelerated reaction system for the development an efficient and sensitive electrochemical sensor to protect the environment and healthcare fields in a broad scale.

Selective capturing of phenolic derivative by a binary metal oxide microcubes for its detection

Development of highly efficient and potential material for toxic p-nitrophenol is an important design for sensitive detection of hazardous species from ecology and environment. Here it is developed, an efficient as well as selective of p-nitrophenol using binary material by electrochemical performances, including good linearity, lower detection limit, good stability, higher reproducibility and extreme sensitivity. The prepared electrode was fabricated by immobilization of SnO₂/CdO microcubes (MCs) with conducting coating binders by using well-known glassy carbon electrode (GCE). The proposed MCs with SnO₂/CdO were well-functionalized and prepared by facile hydrothermal technique. The general instrumentation namely, FTIR, UV/vis, FESEM, XPS, TEM, EDS, and powder XRD were employed for the morphological evaluation of the prepared doped MCs, structural, optical and elemental analyses. The large dynamic range (LDR) from 1.0 to 0.01 mM with 0.13 pM detection limit (S/N = 3), limit of quantification (LOQ; 0.43 pM), and an excellent sensitivity of 7.12 µAµM⁻¹cm⁻² were exhibited by the fabricated binary material based on SnO₂/CdO MCs for selective p-nitrophenol capturing. In shortly, the SnO₂/CdO MCs can be employed as an efficient electron mediator with binary materials fabricated GCE for capturing the p-nitrophenol at ultra-trace amounts. Then the binary synthesized material of SnO₂/CdO MCs is used as potential and sensitive sensor layer by stable electrochemical approach for sensitive capturing of toxic p-nitrophenol from environmental samples.

Ultrasonic energy-assisted preparation of β-cyclodextrin-carbon nanofiber composite: Application for electrochemical sensing of nitrofurantoin

A simple ultrasonic energy assisted synthesis of β-cyclodextrin (β-CD) supported carbon nanofiber composite (CNF) and its potential application in electrochemical sensing of antibiotic nitrofurantoin (NFT) is reported. The elemental composition and surface morphology of the β-CD/CNF composite was validated through Field emission scanning electron microscopy, energy dispersive X-ray microscopy, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and thermogravimetric analysis. The uniform enfolding of hydrophilic β-CD over CNF enhance the aqueous dispersion and offer abundant active surface to the β-CD/CNF composite. Further, the electrocatalytic efficacy of the β-CD/CNF composite is utilized to fabricate an electrochemical sensor for the high sensitive quantitative detection of NFT. Under optimized analytical conditions, the sensor displays a broad working range of 0.004-308 µM and calculated detection limit of 1.8 nM, respectively. In addition, the sensor showcased a good selectivity, storage, and working stability, with amiable reproducibility. The point-of-care applicability of the sensor was demonstrated with NFT spiked human blood serum and urine sample with reliable analytical performance. The simple, cost-effective NFT sensor based on β-CD/CNF offered outstanding analytical performance in real-world samples with higher reliability.

Efficient selective 4-aminophenol sensing and antibacterial activity of ternary Ag2O3·SnO2·Cr2O3 nanoparticles

The electrochemical oxidation of 4-AP based on Ag₂O₃·SnO₂·Cr₂O₃ NPs/binder/GCE sensor.

Detection of toxic choline based on Mn2O3/NiO nanomaterials by an electrochemical method

In this study, a novel in situ choline sensor was assembled by attaching the binary Mn₂O₃/NiO nanoparticles (NPs) onto a glassy carbon electrode (GCE). Initially, Mn₂O₃/NiO NPs were synthesized via a wet-chemical process and fully characterized via XRD, XPS, FESEM, EDS, FTIR and UV-Vis methods. The analytical performances of the choline sensor were evaluated by an electrochemical method in the phosphate buffer phase. The estimated linear dynamic range (LDR) was found to be 0.1 nM to 0.1 mM. The other analytical performances of the choline sensor, such as sensitivity (16.4557 μA μM⁻¹ cm⁻²) and detection limit (5.77 ± 0.29 pM), were also calculated very carefully from the calibration plot. Overall, the choline sensor exhibited a reliable reproducibility, in situ validity, selectivity, interference effect, stability, and intra-day and inter-day performances with high accuracy in a short response time. Moreover, the probe was successfully applied to detect choline in real human, mouse and rabbit serum. This fabrication route would be a novel approach for the detection of selective biochemical sensor in the healthcare and biomedical fields.

In this study, a novel in situ choline sensor was assembled by attached the binary Mn₂O₃/NiO nanoparticles onto glassy carbon electrode, which might be a reliable way to develop of future sensor in the field of biomedical and healthcare fields.

Poly(pyrrole-co-o-toluidine) wrapped CoFe2O4/R(GO–OXSWCNTs) ternary composite material for Ga3+ sensing ability

A ternary P(Py-co-OT)/CF/R(GO–OXSWCNTs) nanocomposite has been fabricated as a novel conductive hybrid material with high stability and excellent electrochemical Ga³⁺ sensing ability.

Detection of uric acid based on doped ZnO/Ag2O/Co3O4 nanoparticle loaded glassy carbon electrode

Highly sensitive and selective uric acid sensor was fabricated using facile wet-chemically prepared ternary doped ZnO/Ag₂O/Co₃O₄ nanoparticles onto glassy carbon electrode by electrochemical approach, which introduced a prospective and reliable route to the future development of enzyme-free sensor by doped nanomaterials in broad scales.

Development of 3-methoxyaniline sensor probe based on thin Ag2O@La2O3 nanosheets for environmental safety

An electrochemical sensor based on glassy carbon electrode modified by Ag₂O@La₂O₃ nanosheets with 5% ethanolic nafion as conducting binder was developed for the selective and ultra-sensitive determination of 3-methoxyanaline in the presence of other interfering toxic chemicals in aqueous system by electrochemical approach for the first time.

Fabrication of 1,4-dioxane sensor based on microwave assisted PAni-SiO2 nanocomposites

In this study, conducting polyaniline (PAni) and silicon dioxide (SiO₂) nanocomposites (NCs) were synthesized for chemical sensing applications by microwave assisted reaction technique. Facile synthesis and characterization of the PAni-SiO₂ nanocomposites were investigated in details and discussed in this report. For the potential application, 1,4-dioxane chemical sensor was fabricated with the PAni-SiO₂ nanocomposites deposited onto glassy carbon electrode (GCE). A very thin uniform film was deposited onto GCE with nanocomposite by using conducting 5% nafion binder at room conditions. To evaluate the sensor analytical performances, a calibration plot such as current versus concentration of 1,4-dioxane was drawn and calculated the analytical parameters from the slope of calibration curve. Results are found as sensitivity (0.5934 µAµmol^-1 L^-2 cm^-2), detection limit (16.0 ± 0.8 pmol L^-1), and quantification limit (LOQ; 53.3 ± 1.5 pmol L^-1) in this observation. Considering the linear region in calibration plot, the linear dynamic range of 1,4-dioxane chemical sensor was found (0.12 nmol L^-1 ∼ 1.2 mmol L^-1). Besides this, the proposed 1,4-dioxane chemical sensor was exhibited good reproducibility, long-term stability, high accuracy in detecting of 1,4-dioxane in real environmental samples. This research is to develop of a selective and an efficient electrochemical sensor. It might be a simple and easy way by applying electrochemical method to ensure the safe and sustainable green environment.

Wet-chemically prepared low-dimensional ZnO/Al2O3/Cr2O3 nanoparticles for xanthine sensor development using an electrochemical method

A reliable xanthine (XNT) chemical sensor was fabricated using a facile wet-chemical method (by co-precipitation) to prepare ZnO/Al₂O₃/Cr₂O₃ nanoparticles (NPs) in an alkaline medium at low temperature. Powder X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectroscopy (EDS), Fourier transform infrared spectroscopy (FTIR) and ultraviolet-visible spectroscopy (UV-vis) were implemented for detailed characterization of the NPs. To fabricate the working electrode as a XNT chemical sensor probe, a glassy carbon electrode (GCE) with a 0.0316 cm² surface area was coated with an ethanolic slurry of the prepared ZnO/Al₂O₃/Cr₂O₃ NPs to make a thin layer and used to analyse XNT in a phosphate buffer system. To evaluate the analytical performances of the XNT chemical sensor, the calibration curve of XNT was plotted as the relationship of current versus the concentration of XNT. The plotted calibration curve was found to be linear over the LDR (linear dynamic range) of 0.05 nM to 5.0 μM. The assembled XNT electrochemical sensor exhibited the highest sensitivity (70.8861 μA μM⁻¹ cm⁻²), the lowest detection limit (1.34 ± 0.07 pM), good reproducibility performance with high accuracy and long-term stability with standard results under ambient conditions. This is a simple route to selectively detect XNT with wet-chemically prepared co-doped ZnO/Al₂O₃/Cr₂O₃ nanomaterials using a reliable electrochemical method at a large scale for safety within healthcare fields.

This is a simple route to detect the selective xanthine with wet-chemically prepared co-doped ZnO/Al₂O₃/Cr₂O₃ nanomaterials by reliable electrochemical method at large scales for the safety of healthcare fields.