How to fix a tibial tubercle osteotomy with distalisation: A finite element analysis

Effect of structural support size and position on depressed tibial plateau fractures: A finite element analysis

Objective

Structural support for depressed tibial plateau fractures is receiving increasing attention. Currently, there has been little biomechanical evaluation of structural support. This work aimed to investigate the effect of structural support size and position on fracture fixation stability.

Methods

A split-depressed tibial plateau fracture model was created according to the fracture map. Cortical screws combined with structural filler were used for fracture fixation. The filler diameter was set to small, medium and large, and the filler position was set to the center and offset by 1, 2 and 3 mm to study the effect of position and size on stability.

Results

The maximum stress on the implant in all scenarios occurs at the lower contact surface between the anterior screw and the filler. Increased support size resulted in increased mean maximum screw stress, depressed fragment axial displacement and separated fragment transverse displacement (screw stress: 266.6 ± 37.7 MPa vs. 266.7 ± 51.0 MPa vs. 273.8 ± 41.5 MPa; depressed displacement: 0.123 ± 0.036 mm vs. 0.133 ± 0.049 mm vs. 0.158 ± 0.050 mm; separated displacement: 0.402 ± 0.031 mm VS 0.412 ± 0.047 mm VS 0.437 ± 0.049 mm). The larger the offset of the support position was, the larger the peak screw stress and the larger the reduction loss of depressed and separated fragment reduction, regardless of the support size. The medium support combined with the central position presented the minimum of peak stress and reduction loss. Cortical bone was below 2 % and trabecular strain was below 10 % for all scenarios.

Conclusion

Central placement of structural support provides superior stability for the treatment of depressed tibial plateau fractures compared to the eccentric placement. When a support is placed centrally, optimal stability is achieved when the diameter matches the diameter of the depressed region. Thus, the utilization of equal-diameter fillers to provide central support appears to be an ideal selection for depressed tibial plateau fractures.

Investigation of dynamic hip plate screw systems in different lengths with finite element analysis

Objectives

Dynamic systems aim to create an environment that encourages bone healing while minimizing stress shielding, which is a phenomenon where the bone loses density due to a lack of stress during the healing process. In this study, it was aimed that the stress distributions on plates of different lengths in the dynamic hip plate screw system were investigated.

Materials and methods

In our study, the human proximal femur model (3-D) obtained from computerized tomography was transferred to Finite Element Analysis (FEA) computer simulation. Plates with 2-4-6 holes were placed on the knitted bone model. The models used in this study were mainly determined as five components: cortical-cancellous bone, lateral plate, cortical screws, and compression neck screws. A 1 mm intertrochanteric fracture area was created from the trochanter major region.

Results

When plates of different lengths were applied, there was no significant difference in the stress in the compression screw and the chamber it was located in.It shows that when a 2-hole plate is used, the stress will be high, especially between the lower cortical screw and the cortex. In these three groups, it was observed that the stress points were in at least 6-hole plates.

Conclusion

The results of this study showed that the shorter the plate applied, the greater the stress on the plate and cortical screws in the femur diaphysis.

Comparison of four different screw configurations for the fixation of Fulkerson osteotomy: a finite element analysis

BACKGROUND

Conventionally, two 4.5 mm cortical screws inserted toward the posterior tibial cortex are usually advocated for the fixation of Fulkerson osteotomy. This finite element analysis aimed to compare the biomechanical behavior of four different screw configurations to fix the Fulkerson osteotomy.

MATERIALS AND METHODS

Fulkerson osteotomy was modeled using computerized tomography (CT) data of a patient with patellofemoral instability and fixed with four different screw configurations using two 4.5 mm cortical screws in the axial plane. The configurations were as follows: (1) two screws perpendicular to the osteotomy plane, (2) two screws perpendicular to the posterior cortex of the tibia, (3) the upper screw perpendicular to the osteotomy plane, but the lower screw is perpendicular to the posterior cortex of the tibia, and (4) the reverse position of the screw configuration in the third scenario. Gap formation, sliding, displacement, frictional stress, and deformation of the components were calculated and reported.

RESULTS

The osteotomy fragment moved superiorly after loading the models with 1654 N patellar tendon traction force. Since the proximal cut is sloped (bevel-cut osteotomy), the osteotomy fragment slid and rested on the upper tibial surface. Afterward, the upper surface of the osteotomy fragment acted as a fulcrum, and the distal part of the fragment began to separate from the tibia while the screws resisted the displacement. The resultant total displacement was 0.319 mm, 0.307 mm, 0.333 mm, and 0.245 mm from the first scenario to the fourth scenario, respectively. The minimum displacement was detected in the fourth scenario (upper screw perpendicular to the osteotomy plane and lower screw perpendicular to the posterior tibial cortex). Maximum frictional stress and maximum pressure between components on both surfaces were highest in the first scenario (both screws perpendicular to the osteotomy plane).

CONCLUSIONS

A divergent screw configuration in which the upper screw is inserted perpendicular to the osteotomy plane and the lower screw is inserted perpendicular to the posterior tibial cortex might be a better option for the fixation of Fulkerson osteotomy. Level of evidence Level V, mechanism-based reasoning.