Effects of endpoint temperature and thickness on quality of whole muscle non-intact steaks cooked in a Radio Frequency oven

Effects of Radio Frequency Tempering on the Texture of Frozen Tilapia Fillets

Radio frequency (RF) tempering has been proposed as a new alternative method for tempering frozen products because of its advantages of rapid and volumetric heating. In this study, the texture of RF-tempered frozen tilapia fillets was determined under different RF conditions, the effects of related factors on the texture were analyzed, and the mechanisms by which RF tempering affected the texture of the tempered fillets were evaluated. The results show that the springiness (from 0.84 mm to 0.79 mm), cohesiveness (from 0.64 mm to 0.57 mm), and resilience (from 0.33 mm to 0.25 mm) decreased as the electrode gap was increased and the power remained at 600 W, while the shear force increased as the power was increased for the 12 cm electrode gap (from 15.18 N to 16.98 N), and the myofibril fragmentation index (MFI) values were markedly higher at 600 W than at 300 W or 900 W (p < 0.05). In addition, the tempering uniformity had a positive effect on hardness and chewiness. The statistical analysis showed that the texture after RF tempering under different RF conditions correlated relatively strongly with the free water content, cooking loss, and migration of bound water to immobilized water. The decrease in free water and bound water migration to immobilized water resulted in a significant increase in cohesiveness and resilience.

Water status evolution of pork blocks at different cooking procedures: A two-dimensional LF-NMR T1-T2 relaxation study

A two-dimensional low-field nuclear magnetic resonance (LF-NMR) T₁-T₂ relaxation technique was developed to contrast the water status evolution during different cooking procedures (steam and boiling cooking). Meat quality, water distribution, microstructure and protein properties were determined. The results showed that steamed meats had lower cooking loss and shear force, but higher redness, proton relaxation intensity (T₁ and T₂) and proton density than boiled meats. The differences in water distribution between the two cooking procedures appeared at approximately 40 °C, with acceleration at 60 °C, and the most remarkable difference was shown at 80 °C. Boiling resulted in more damage to muscle structure and greater protein denaturation than steam cooking. Meanwhile, α-helixes and β-turns increased, but β-sheets and random coils decreased in steamed meats compared with boiled meats. Changes in microstructural and protein properties were closely associated with water status evolution in cooked meat during cooking.

Thermophysical Properties of Beef Steaks of Varying Thicknesses Cooked With Low and High Grill Surface Temperatures

The objective of this study was to determine the thermodynamic and physical properties of beef strip loin steaks of varying thicknesses and USDA quality grades cooked with high and low grill surface temperatures. Thermal characteristics described by changes in the denaturation temperature (between 55°C – 60°C) and enthalpies of protein denaturation (70°C – 75°C) both differed (P = 0.031 and P = 0.001, respectively) among thick steaks, with thick steaks cooked on a high grill surface temperature having a lower denaturation temperature and enthalpy compared with thick steaks cooked on a low grill surface temperature. No differences (P &gt; 0.05) were observed among thin steaks for denaturation temperature or enthalpy. The elastic behaviors of the surface and center of the steaks were analyzed to determine how the microstructure of the beef responded to applied stress. The elastic behavior of steak centers was influenced in a three-way interaction (P = 0.029) between quality grade, steak thickness, and grill surface temperature. The elastic behavior of the surface of steaks was influenced by the interaction of quality grade and steak thickness (P = 0.031). These interactions, along with the differences in the thermal characteristic of proteins, suggest that the microstructure of steaks was affected by each cooking treatment group. Hardness, resilience, and chewiness were each influenced by a three-way interaction (P = 0.023; 0.014; and 0.030; respectively). Thin steaks possessed greater cohesiveness (P = 0.038) and shear force ( P = 0.007) values. Meanwhile, thin steaks exhibited lower springiness (P = 0.002). The measured alterations in thermal and physical proper- ties in the beef steaks suggest that the composition, thickness, and cooking regiments impact the microstructure of beef, and this was ultimately confirmed through textural measurements. The results of this research can be used in the design of cooking processes that match beef characteristics.

Sarcoplasmic Proteome Profile and Internal Color of Beef Longissimus Lumborum Steaks Cooked to Different Endpoint Temperatures

The complex relationship between endpoint temperature, sarcoplasmic proteome, and internal color in cooked steaks is yet to be examined. The objective of the present study was to characterize the changes in sarcoplasmic proteome and their influence on the internal color of beef longissimus lumborum (LL) steaks cooked to different endpoint temperatures. Two 2.5-cm-thick LL steaks were fabricated from 9 beef strip loins and were cooked to an internal endpoint temperature of either 60°C (C-60) or 71°C (C-71). Cooked steaks were cooled and sliced parallel to the grilled surface, and internal color was evaluated instrumentally. Sarcoplasmic proteome from the interiors of the cooked steaks was analyzed using two-dimensional electrophoresis, and the gel images were digitally analyzed. The protein spots exhibiting more than 2-fold intensity differences (P &lt; 0.05) were subjected to in-gel tryptic digestion and were identified by tandem mass spectrometry. The C-60 steaks demonstrated greater (P &lt; 0.05) redness and color stability than the C-71 ones. Eleven differentially abundant protein spots were identified, and they belonged to 6 functional groups (transport proteins, enzymes in energy metabolism, chaperones, antioxidant proteins, enzymes in amino acid metabolism, and glycolytic enzymes). While 10 spots were overabundant (P &lt; 0.05) in C-60 steaks, 1 spot was overabundant (P &lt; 0.05) in C-71 steaks. The spot overabundant in C-71 samples was identified as myoglobin, suggesting the possible role of post-translational modifications in the heme protein’s thermal stability. The results indicated that the endpoint cooking temperature influenced sarcoplasmic proteome profile and internal color of cooked beef LL steaks. The overabundant proteins in steaks cooked to 60°C may be exploited as potential biomarkers for undercooked beef, which is a source for foodborne infections.

Computer simulation for improving radio frequency (RF) heating uniformity of food products: A review

Radio frequency (RF) heating has great potential for achieving rapid and volumetric heating in foods, providing safe and high-quality food products due to deep penetration depth, moisture self-balance effects, and leaving no chemical residues. However, the nonuniform heating problem (usually resulting in hot and cold spots in the heated product) needs to be resolved. The inhomogeneous temperature distribution not only affects the quality of the food but also raises the issue of food safety when the microorganisms or insects may not be controlled in the cold spots. The mathematical modeling for RF heating processes has been extensively studied in a wide variety of agricultural products recently. This paper presents a comprehensive review of recent progresses in computer simulation for RF heating uniformity improvement and the offered solutions to reduce the heating nonuniformity. It provides a brief introduction on the basic principle of RF heating technology, analyzes the applications of numerical simulation, and discusses the factors influencing the RF heating uniformity and the possible methods to improve heating uniformity. Mathematical modeling improves the understanding of RF heating of food and is essential to optimize the RF treatment protocol for pasteurization and disinfestation applications. Recommendations for future research have been proposed to further improve the accuracy of numerical models, by covering both heat and mass transfers in the model, validating these models with sample movement and mixing, and identifying the important model parameters by sensitivity analysis.