Degradability and biofouling of oxo-biodegradable polyethylene in the planktonic and benthic zones of the Arabian Gulf

Spatial analysis of total mercury concentration in surface sediments in Sulaibikhat Bay, Kuwait

Sulaibikhat Bay, a shallow estuarine embayment in the southern part of Kuwait Bay, has undergone substantial anthropogenic impacts over the past decade, resulting in altered sediment quality and mercury (T-Hg) contamination. This bay, bordered by the Doha Power Plant and Shuwaikh Port, receives untreated sewage and industrial waste through 17 outfalls, nine of which remain active. To assess the extent of contamination, 44 surface sediment samples were analyzed for T-Hg concentrations and fluxes. T-Hg concentrations ranged from 8 to 800 ng g-1, averaging 74 ng g-1. Elevated levels were observed predominantly on the eastern side of the bay, with a maximum of 800 ng g-1 near Outfall 3. In contrast, the western side exhibited lower concentrations, ranging from 17 to 50 ng g-1. Mercury fluxes mirrored this spatial pattern, with the highest flux recorded at 250 ng cm-2 yr-1. Assessment using enrichment factors and the geoaccumulation index indicated that western bay sediments are uncontaminated to moderately contaminated, while the eastern side is moderately to strongly contaminated, with some areas classified as extremely contaminated. Although most T-Hg concentrations were below Interim Sediment Quality Guideline (ISQG) thresholds, location H41 exceeded the Probable Effect Level (PEL) at 800 ng g-1. These findings, consistent with previous studies, raise concerns about higher mercury levels in deeper sediments, which could resuspend during dredging or coastal development, increasing risks to the marine ecosystem. This study highlights the urgent need for a strategic management plan to mitigate contamination, protect the bay, and guide future monitoring and conservation efforts.

Biodegradable Fiber Preparation Technique to Meet Industrial Requisites Through Sheath-Core Melt-Spinning

Biodegradable polymers are essential for sustainable plastic life cycles and contribute to a carbon-neutral society. Here, we explore the development of biodegradable fibers with excellent mechanical properties using polypropylene (PP) and thermoplastic starch (TPS) blends. To address the inherent immiscibility between hydrophobic PP and hydrophilic TPS, hydrophilic modification and a masterbatch approach were employed. Melt-spinning trials demonstrated that the modified PP and TPS blends (mPP/TPS) exhibited excellent spinnability and processability comparable to virgin PP. A sheath-core configuration was introduced to enhance biodegradability while maintaining structural stability, with an mPP-rich part as the core and a TPS-rich part with a biodegradable promoter (BP) as the sheath. SEM and DSC analyses confirmed strong interfacial compatibility, uniform fiber morphology, and single melting points, indicating no phase separation. Mechanical testing showed that the sheath-core fibers met industrial requirements, achieving a tenacity of up to 2.47 gf/den and tensile strain above 73%. The addition of a BP increased the biodegradability rate, with PP/TPS/BP fibers achieving 65.93% biodegradation after 115 days, compared to 37.00% for BP-free fibers. These results demonstrate the feasibility of blending petroleum-based polymers with bio-based components to create fibers that balance biodegradability, spinnability, and mechanical performance, offering a sustainable solution for industrial applications.

Early signs of plastic degradation and fragmentation: A 40-day study in marine environments

Conventional plastics are widely present in the ocean as marine plastic debris. This in-situ study investigates the degradability and fragmentation of seven common conventional plastics (PET, PVC, PS, EPS, PP, HDPE, and LDPE) in natural marine environments over a 40-day period. All plastics showed significant chemical changes and oscillating plastic oxidation levels, indicating the synergistic processes of oxidation and removal of oxidation products. Polystyrenes and polymers with heteroatoms showed the largest degradation potentials, while pure polyolefins exhibited the highest fragmentation risks. SEM images suggest potentials of EPS and pure polyolefins in generating microplastic fragments, and polymers with heteroatoms in generating nanoplastic fragments. PS did not exhibit any surface degradation signs, potentially due to enhanced crystallinity through oxidation. The findings highlight the need for reduced usage of EPS and pure polyolefins which are commonly applied as disposable utensils and food packaging, and prioritized cleanup of these polymers to reduce microplastic pollution in the environment.

Degradation efficiency of biodegradable plastics in subtropical open-air and marine environments: Implications for plastic pollution

Bioplastics are increasingly used as a solution to tackle plastic pollution problems. However, their degradability in natural environments is currently under debate. To evaluate their degradation efficiencies, we conducted in-situ degradation experiments in an open-air and two marine environments in Hong Kong. Three groups of biodegradable plastic were tested, namely (1) additive-modified low-density polyethylene (LDPE), labelled as oxo-biodegradable or photodegradable plastics, (2) polylactic acid (PLA), and (3) polyvinyl alcohol (PVA)/starch blends. Most biodegradable plastics fail to completely degrade but remain visually present after six months of exposure. Only PLA is able to demonstrate 100 % disintegration in one to three months in marine settings, suggesting that subtropical marine environments may favor PLA degradation. Biodegradable plastics that are bio-based (PLA and PVA/Starch blends) show notably larger mass losses by 23-100 % than the fossil-based ones (modified-LDPE). Our results reveal higher degradation efficiencies of PLA and PVA/Cassava starch blend in marine than open-air settings (with mass losses larger by 50 %, and by 39-41 %, respectively), potentially via biodegradation and hydrolysis. Meanwhile, modified-LDPE and PVA/Corn starch blends in general show higher degradation efficiencies in open-air than marine settings (with mass losses larger by 2 %, and by 17-33 %, respectively), potentially via abiotic oxidation. Since all tested biodegradable plastics exhibit potential fragmentation signs, further investigation is needed to characterize the behaviours of the microplastics generated. The current labelling on biodegradable bags fails to provide comprehensive information regarding their actual environmental degradation behaviours, especially considering their fragmentation risk and limited degradation exhibited in this study. This highlights the imperative for improved messaging to ensure consumers are better informed about these products.

Mining strategies for isolating plastic-degrading microorganisms

Plastic waste is a growing global pollutant. Plastic degradation by microorganisms has captured attention as an earth-friendly tactic. Although the mechanisms of plastic degradation by bacteria, fungi, and algae have been explored over the past decade, a large knowledge gap still exists regarding the identification, sorting, and cultivation of efficient plastic degraders, primarily because of their uncultivability. Advances in sequencing techniques and bioinformatics have enabled the identification of microbial degraders and related enzymes and genes involved in plastic biodegradation. In this review, we provide an outline of the situation of plastic degradation and summarize the methods for effective microbial identification using multidisciplinary techniques such as multiomics, meta-analysis, and spectroscopy. This review introduces new strategies for controlling plastic pollution in an environmentally friendly manner. Using this information, highly efficient and colonizing plastic degraders can be mined via targeted sorting and cultivation. In addition, based on the recognized rules and plastic degraders, we can perform an in-depth analysis of the associated degradation mechanism, metabolic features, and interactions.

Environmental exposure more than plastic composition shapes marine microplastic-associated bacterial communities in Pacific versus Caribbean field incubations

Microplastics have arisen as a global threat to marine ecosystems. In this study, we explored the role that plastic polymer type, incubation time and geographic location have on shaping the microbial community adhered to the microplastics, termed the plastisphere. We performed detailed bacterial plastisphere community analyses on microplastics of six different household plastic polymers, serving as proxies of secondary microplastics, incubated for 6 weeks in coastal Pacific waters. These bacterial communities were compared to the plastisphere communities grown on identical microplastic particles incubated in the coastal Caribbean Sea at Bocas del Toro, Panama. Ribosomal gene sequencing analyses revealed that bacterial community composition did not exhibit a significant preference for plastic type at either site but was instead driven by the incubation time and geographic location. We identified a 'core plastisphere' composed of 57 amplicon sequence variants common to all plastic types, incubation times and locations, with possible synergies between taxa. This study contributes to our understanding of the importance of geography in addition to exposure time, in the composition of the plastisphere.

Degradation of starch-based bioplastic bags in the pelagic and benthic zones of the Gulf of Oman

The Gulf of Oman is becoming increasingly polluted with plastics, hence bioplastics have been considered 'a substitute', although their biodegradability in marine environments has not been well investigated. Most research has been performed on cellulose-based bioplastics, whereas starch-based bioplastics have proven to be a suitable, but less researched, alternative. This study is the first of its kind designed to investigate the degradability of two different types of starch-based bioplastic bags, available in the market and labeled as "biodegradable", in the pelagic and benthic zones of one of the warmest marine environment in the world. Fourier-Transform Infrared Spectroscopy (FTIR) showed a clear reduction in the presence of OH, CH, and CO in the bioplastic bags after 5 weeks of immersion. Thermo-Gravimetric Analysis (TGA) indicated degradation of glycerol, starch, and polyethylene. The biofouling bacterial communities on bioplastic surfaces showed distinct grouping based on the immersion zone. Candidaatus saccharibacteria, Verrucomicrobiae, Acidimicrobiia and Planctomycetia sequences were only detectable on bioplastics in the pelagic zone, whereas Actinomyces, Pseudomonas, Sphingobium and Acinetobacter related sequences were only found on bioplastics in the benthic layer. We conclude that starch-based bioplastics are more readily degradable in the Gulf of Oman than conventional plastics, hence could serve as a better environmentally friendly alternative.

Physicochemical and biological ageing processes of (micro)plastics in the environment: a multi-tiered study on polyethylene

Pollution by plastic and microplastic impacts the environment globally. Knowledge on the ageing mechanisms of plastics in natural settings is needed to understand their environmental fate and their reactivity in the ecosystems. Accordingly, the study of ageing processes is gaining focus in the context of the environmental sciences. However, laboratory-based experimental research has typically assessed individual ageing processes, limiting environmental applicability. In this study, we propose a multi-tiered approach to study the environmental ageing of polyethylene plastic fragments focusing on the combined assessment of physical and biological processes in sequence. The ageing protocol included ultraviolet irradiation in air and in a range of water solutions, followed by a biofouling test. Changes in surface characteristics were assessed by Fourier transform infrared spectroscopy, scanning electron microscopy, and water contact angle. UV radiation both in air and water caused a significant increase in the density of oxidized groups (i.e., hydroxyl and carbonyl) on the plastic surface, whereby water solution chemistry influenced the process both by modulating surface oxidation and morphology. Biofouling, too, was a strong determinant of surface alterations, regardless of the prior irradiation treatments. All biofouled samples present (i) specific infrared bands of new surface functional groups (e.g., amides and polysaccharides), (ii) a further increase in hydroxyl and carbonyl groups, (iii) the diffuse presence of algal biofilm on the plastic surface, and (iv) a significant decrease in surface hydrophobicity. This suggests that biological-driven alterations are not affected by the level of physicochemical ageing and may represent, in real settings, the main driver of alteration of both weathered and pristine plastics. This work highlights the potentially pivotal role of biofouling as the main process of plastic ageing, providing useful technical insights for future experimental works. These results also confirm that a multi-tiered laboratory approach permits a realistic simulation of plastic environmental ageing in controlled conditions.

Plastic-microbe interaction in the marine environment: Research methods and opportunities

Approximately 9 million metric tons of plastics enters the ocean annually, and once in the marine environment, plastic surfaces can be quickly colonised by marine microorganisms, forming a biofilm. Studies on plastic debris-biofilm associations, known as plastisphere, have increased exponentially within the last few years. In this review, we first briefly summarise methods and techniques used in exploring plastic-microbe interactions. Then we highlight research gaps and provide future research opportunities for marine plastisphere studies, especially, on plastic characterisation and standardised biodegradation tests, the fate of "environmentally friendly" plastics, and plastisphere of coastal habitats. Located in the tropics, Southeast Asian (SEA) countries are significant contributors to marine plastic debris. However, plastisphere studies in this region are lacking and therefore, we discuss how the unique environmental conditions in the SEA seas may affect plastic-microbe interaction and why there is an imperative need to conduct plastisphere studies in SEA marine environments. Finally, we also highlight the lack of understanding of the pathogenicity and ecotoxicological effects of plastisphere on marine ecosystems.

Soil plastisphere: Exploration methods, influencing factors, and ecological insights

Microplastic (MP), an emerging contaminant, is globally prevalent and poses potential environmental threats and ecological risks to both aquatic and terrestrial ecosystems. When MPs enter into natural environments, they may serve as artificial substrates for microbial colonization and plastisphere formation, providing new ecological niches for microorganisms. Recent studies of the plastisphere have focused on aquatic ecosystems. However, our understanding of the soil plastisphere e.g. its formation process, microbial ecology, co-transport of organic pollutants and heavy metals, and effects on biogeochemical processes is still very limited. This review summarizes latest methods used to explore the soil plastisphere, assesses the factors influencing the microbial ecology of the soil plastisphere, and sheds light on potential ecological risks caused by the soil plastisphere. The formation and succession of soil plastisphere communities can be driven by MP characteristics and soil environmental factors. The soil plastisphere may affect a series of ecological processes, especially the co-transport of environmental contaminants, biodegradation of MPs, and soil carbon cycling. We aim to narrow the knowledge gap between the soil and aquatic plastisphere, and provide valuable guidance for future research on the soil plastisphere in MP-contaminated soils.

Examining the dependence of macroplastic fragmentation on coastal processes (Chesapeake Bay, Maryland)

Plastic debris in the coastal environment is subject to complex and poorly characterized weathering processes. To better understand how key environmental factors affect plastic degradation in a coastal zone, we conducted an in situ experiment. We deployed strips of high density polyethylene (HDPE) and polystyrene (PS) in paired coastal areas of contrasting conditions (hydrodynamic activity: erosional or depositional; water depths: subtidal or intertidal). Strips were collected after environmental exposures at 4, 8, and 43 weeks and analyzed for change in mass, algal biofilm growth, and imaged by petrographic and electron microscopy (SEM-EDS). Significant surface erosion was evident on both polymers, and was more rapid and more extensive with PS. Degradation of PS was responsive to intensity of hydrodynamic activity, and was greater at intertidal depths, highlighting the critical role played by photo-oxidation in the coastal zone, and suggesting that algal biofilms may slow degradation by playing a photo-protective role.

Marine hydrocarbon-degrading bacteria breakdown poly(ethylene terephthalate) (PET)

Pollution of aquatic ecosystems by plastic wastes poses severe environmental and health problems and has prompted scientific investigations on the fate and factors contributing to the modification of plastics in the marine environment. Here, we investigated, by means of microcosm studies, the role of hydrocarbon-degrading bacteria in the degradation of poly(ethylene terephthalate) (PET), the main constituents of plastic bottles, in the marine environment. To this aim, different bacterial consortia, previously acclimated to representative hydrocarbons fractions namely, tetradecane (aliphatic fraction), diesel (mixture of hydrocarbons), and naphthalene/phenantrene (aromatic fraction), were used as inocula of microcosm experiments, in order to identify peculiar specialization in poly(ethylene terephthalate) degradation. Upon formation of a mature biofilm on the surface of poly(ethylene terephthalate) films, the bacterial biodiversity and degradation efficiency of each selected consortium was analyzed. Notably, significant differences on biofilm biodiversity were observed with distinctive hydrocarbons-degraders being enriched on poly(ethylene terephthalate) surface, such as Alcanivorax, Hyphomonas, and Cycloclasticus species. Interestingly, ATR-FTIR analyses, supported by SEM and water contact angle measurements, revealed major alterations of the surface chemistry and morphology of PET films, mainly driven by the bacterial consortia enriched on tetradecane and diesel. Distinctive signatures of microbial activity were the alteration of the FTIR spectra as a consequence of PET chain scission through the hydrolysis of the ester bond, the increased sample hydrophobicity as well as the formation of small cracks and cavities on the surface of the film. In conclusion, our study demonstrates for the first time that hydrocarbons-degrading marine bacteria have the potential to degrade poly(ethylene terephthalate), although their degradative activity could potentially trigger the formation of harmful microplastics in the marine environment.

Food or just a free ride? A meta-analysis reveals the global diversity of the Plastisphere

It is now indisputable that plastics are ubiquitous and problematic in ecosystems globally. Many suggestions have been made about the role that biofilms colonizing plastics in the environment—termed the “Plastisphere”—may play in the transportation and ecological impact of these plastics. By collecting and re-analyzing all raw 16S rRNA gene sequencing and metadata from 2,229 samples within 35 studies, we have performed the first meta-analysis of the Plastisphere in marine, freshwater, other aquatic (e.g., brackish or aquaculture) and terrestrial environments. We show that random forest models can be trained to differentiate between groupings of environmental factors as well as aspects of study design, but—crucially—also between plastics when compared with control biofilms and between different plastic types and community successional stages. Our meta-analysis confirms that potentially biodegrading Plastisphere members, the hydrocarbonoclastic Oceanospirillales and Alteromonadales are consistently more abundant in plastic than control biofilm samples across multiple studies and environments. This indicates the predilection of these organisms for plastics and confirms the urgent need for their ability to biodegrade plastics to be comprehensively tested. We also identified key knowledge gaps that should be addressed by future studies.