Preparation of nanofiltration membranes from polyacrylonitrile ultrafiltration membranes

Construction of three-dimensional proton-conduction networks with functionalized PU@PAN/UiO-66 nanofibers for proton exchange membranes

Proton exchange membranes (PEMs) play an important role in fuel cells. For realizing a nanofiber (NF) structure design in PEMs, the material should have tunable pores and a high specific area. In this study, we attempt to design a novel NF with synergistic architecture doped MOF for constructing three-dimensional (3D) proton conduction networks in PEMs. In this framework, UiO-66-COOH serves as a platform for proton sites to synergistically promote proton conductivity via polyvinylpyrrolidone dissolution, hydrolyzation of polyacrylonitrile, and sulfamic acid functionalization of the shell-layer NF. Benefiting from enriched proton-transfer sites in NFs, the obtained composite membrane overcomes the trade-off among proton conductivity, methanol permeability, and mechanical stability. The composite membrane with 50 % fiber (Nafion/S@NF-50) exhibited a high proton conductivity of 0.212 S cm-1 at 80 °C and 100 % relative humidity, suppressed methanol permeability of 0.66 × 10-7 cm2 s-1, and the maximum power density of direct methanol fuel cell is 182.6 mW cm-2. Density functional theory was used to verify the important role of sulfamic acid in proton transfer, and the activation energy barriers under anhydrous and hydrous conditions are only 0.337 and 0.081 kcal, respectively. This study opens up new pathways for synthesizing NF composite PEMs.

Non-Solvent- and Temperature-Induced Phase Separations of Polylaurolactam Solutions in Benzyl Alcohol as Methods for Producing Microfiltration Membranes

The possibility of obtaining porous films through solutions of polylaurolactam (PA12) in benzyl alcohol (BA) was considered. The theoretical calculation of the phase diagram showed the presence of the upper critical solution temperature (UCST) for the PA12/BA system at 157 °C. The PA12 completely dissolved in BA at higher temperatures, but the resulting solutions underwent phase separation upon cooling down to 120–140 °C because of the PA12’s crystallization. The viscosity of the 10–40% PA12 solutions increased according to a power law but remained low and did not exceed 5 Pa·s at 160 °C. Regardless of the concentration, PA12 formed a dispersed phase when its solutions were cooled, which did not allow for the obtention of strong films. On the contrary, the phase separation of the 20–30% PA12 solutions under the action of a non-solvent (isopropanol) leads to the formation of flexible microporous films. The measurement of the porosity, wettability, strength, permeability, and rejection of submicron particles showed the best results for a porous film produced from a 30% solution by non-solvent-induced phase separation. This process makes it possible to obtain a membrane material with a 240 nm particle rejection of 99.6% and a permeate flow of 1.5 kg/m2hbar for contaminated water and 69.9 kg/m2hbar for pure water.

New Hybrid Nanofiltration Membranes with Enhanced Flux and Separation Performances Based on Polyphenylene Ether-Ether-Sulfone/Polyacrylonitrile/SBA-15

This study presents the preparation of hybrid nanofiltration membranes based on poly(1,4-phenylene ether ether sulfone), polyacrylonitrile, poly(vinyl pyrrolidone), and SBA-15 mesoporous silica. Laser treatment of polymeric solutions to enhance the hydrophilicity and performance of membranes was investigated. The membranes’ structure was characterized using scanning electron (SEM) and atomic force (AFM) microscopy and contact angle measurements. The addition of PAN in the casting solution produced significant changes in the membrane structure, from finger-like porous structures to sponge-like porous structures. Increased PAN concentration in the membrane composition enhanced the hydrophilicity of the membrane surface, which also accounted for the improvement in the antifouling capabilities. The permeation of apple pomace extract and the content of polyphenols and flavonoids were used to evaluate the efficacy of the hybrid membranes created. The results showed that the hybrid nanofiltration membranes based on PPEES/PAN/PVP/SBA-15: 15/5/1/1 and 17/3/1/1 exposed to laser for 5 min present a higher rejection coefficient to total polyphenols (78.6 ± 0.7% and 97.8 ± 0.9%, respectively) and flavonoids (28.7 ± 0.2% and 50.3 ± 0.4%, respectively) and are substantially better than a commercial membrane with MWCO 1000 Da or PPEES-PVP-based membrane.

Polymeric Membranes for Oil-Water Separation: A Review

This review is devoted to the application of bulk synthetic polymers such as polysulfone (PSf), polyethersulfone (PES), polyacrylonitrile (PAN), and polyvinylidene fluoride (PVDF) for the separation of oil-water emulsions. Due to the high hydrophobicity of the presented polymers and their tendency to be contaminated with water-oil emulsions, methods for the hydrophilization of membranes based on them were analyzed: the mixing of polymers, the introduction of inorganic additives, and surface modification. In addition, membranes based on natural hydrophilic materials (cellulose and its derivatives) are given as a comparison.

Surface Modification of Polyacrylonitrile Membrane by Chemical Reaction and Physical Coating: Comparison between Static and Pore-Flowing Procedures

The influences of static and pore-flowing procedures on the surface modification of a polyacrylonitrile (PAN) ultrafiltration membrane through chemical reaction and physical coating were investigated in detail. For chemical modification by ethanolamine, a membrane modified by the pore-flowing procedure showed a higher flux and different morphology. The reasons were explained by two effects: the pore-flowing resistance to the random thermal motion of PAN at high temperatures and different reaction kinetics related to the reactant concentration profile on the interface between the membrane and reaction solution and the kinetic property of the fluid (driving force and miscibility) and reaction (time and rate). For physical coating modification, a dense and flat layer via a loose and random layer was formed during the pore-flowing process and static process, which changed the flux and antifouling property of the membrane. The membrane prepared by dead-end filtration showed the best trade-off between the flux and antifouling property. Overall, the procedure kinetics plays an important role in the optimization of membrane modification.

Polymer application for separation/filtration of biological active compounds

Membrane technology is an important part of the engineer’s toolbox. This is especially true for industries that process food and other products with their primary source from nature. This review is focused on ongoing development work using membrane technologies for concentration and separation of biologically active compounds, such as polyphenols and flavonoids. We provide the readers not only with the last results achieve in this field but also, we deliver detailed information about the membrane types and polymers used for their preparation.

Characterization and antifouling properties of polyethylene glycol doped PAN–CAP blend membrane

The effects of polyethylene glycol (PEG) as an additive to a cellulose acetate phthalate–polyacrylonitrile blend membrane in the ultrafiltration range were investigated.

Polyphenylsulfone-based solvent resistant nanofiltration (SRNF) membrane incorporated with copper-1,3,5-benzenetricarboxylate (Cu-BTC) nanoparticles for methanol separation

Mixed matrix membranes (MMMs) of various properties were prepared for a solvent resistant nanofiltration (SRNF) by incorporating polyphenylsulfone (PPSU) membranes with copper-1,3,5-benzenetricarboxylate (Cu-BTC) nanoparticles at different loadings.