Well-defined block copolymer ionomers and their blend membranes for proton exchange membrane fuel cell

Sulfonated Pentablock Copolymer (NexarTM) for Water Remediation and Other Applications

This review focuses on the use of a sulfonated pentablock copolymer commercialized as NexarTM in water purification applications. The properties and the use of sulfonated copolymers, in general, and of NexarTM, in particular, are described within a brief reference focusing on the problem of different water contaminants, purification technologies, and the use of nanomaterials and nanocomposites for water treatment. In addition to desalination and pervaporation processes, adsorption and photocatalytic processes are also considered here. The reported results confirm the possibility of using NexarTM as a matrix for embedded nanoparticles, exploiting their performance in adsorption and photocatalytic processes and preventing their dispersion in the environment. Furthermore, the reported antimicrobial and antibiofouling properties of NexarTM make it a promising material for achieving active coatings that are able to enhance commercial filter lifetime and performance. The coated filters show selective and efficient removal of cationic contaminants in filtration processes, which is not observed with a bare commercial filter. The UV surface treatment and/or the addition of nanostructures such as graphene oxide (GO) flakes confer NexarTM with coating additional functionalities and activity. Finally, other application fields of this polymer are reported, i.e., energy and/or gas separation, suggesting its possible use as an efficient and economical alternative to the more well-known Nafion polymer.

Sulfonated Block Copolymers: Synthesis, Chemical Modification, Self-Assembly Morphologies, and Recent Applications

Scientific research based on the self-assembly behavior of block copolymers (BCs) comprising charged-neutral segments has emerged as a novel strategy mainly looking for the optimization of efficiency in the generation and storage of electrical energy. The sulfonation reaction re- presents one of the most commonly employed methodologies by scientific investigations to reach the desired amphiphilic character, leading to enough ion concentration to modify and control the entire self-assembly behavior of the BCs. Recently, several works have studied and exploited these changes, inducing improvement on the mechanical properties, ionic conduction capabilities, colloidal solubility, interface activity, and stabilization of dispersed particles, among others. This review aims to present a description of recent works focused on obtaining amphiphilic block copolymers, specifically those that were synthesized by a living/controlled polymerization method and that have introduced the amphiphilic character by the sulfonation of one of the segments. Additionally, relevant works that have evidenced morphological and/or structural changes regarding the pristine BC as a result of the chemical modification are discussed. Finally, several emerging practical applications are analyzed to highlight the main drawbacks and challenges that should be addressed to overcome the development and understanding of these complex systems.

Hydrophilic Cross-Linked Aliphatic Hydrocarbon Diblock Copolymer as Proton Exchange Membrane for Fuel Cells

This study proposes a hydrophobic and hydrophilic aliphatic diblock copolymer wherein the hydrophobic block contains glycidyl methacrylate (GMA) units that are distanced by poly(acrylonitrile) (PAN) segments to fabricate a proton exchange membrane (PEM). This diblock copolymer also known as ionomer due to the hydrophilic block comprising 3-sulfopropyl methacrylate potassium salt (SPM) block. The diblock copolymer was synthesized in the one-pot atom transfer radical polymerization (ATRP) synthesis. Subsequently, the membrane was fabricated by means of solution casting in which an organic diamine, e.g., ethylene diamine (EDA), was introduced to crosslink the diblock copolymer chains via the addition of amine to the epoxide group of GMA. As a result, the PEM attained possesses dual continuous phases, in which the hydrophobic domains are either agglomerated or bridged by the EDA-derived crosslinks, whereas the hydrophilic domains constitute the primary proton conducting channels. The in-situ crosslinking hydrophobic block by using a hydrophilic cross-linker represents the merit aspect since it leads to both improved proton conductivity and dimensional stability in alcohol fuel. To characterize the above properties, Nafion^® 117 and random copolymer of P(AN-co-GMA-co-SPM) were used as control samples. The PEM with the optimized composition demonstrates slightly better fuel cell performance than Nafion 117. Lastly, this diblock ionomer is nonfluorinated and hence favors lowering down both material and environmental costs.

Preparation of Graft Poly(Arylene Ether Sulfone)s-Based Copolymer with Enhanced Phase-Separated Morphology as Proton Exchange Membranes via Atom Transfer Radical Polymerization

Novel proton exchange membranes (PEMs) based on graft copoly(arylene ether sulfone)s with enhanced phase-separated morphology were prepared using atom transfer radical polymerization (ATRP). A series of PEMs with different graft lengths and sulfonation degrees were prepared. The phase-separated morphologies were confirmed by transmission electron microscopy. Among the membranes prepared and evaluated, PAESPS18S2 exhibited considerably high proton conductivity (0.151 S/cm, 85 °C), benefitting from the graft polymer architecture and phase-separated morphology. The membranes also possessed excellent thermal and chemical stabilities. Highly conductive and stable copoly(arylene ether sulfone)-based membranes would be promising candidates as polymer electrolytes for fuel cell applications.

Self-Assembly Investigations of Sulfonated Poly(methyl methacrylate-block-styrene) Diblock Copolymer Thin Films

Poly(methyl methacrylate-block-styrene) block copolymers (BCs) of low dispersity were selectively sulfonated on the styrenic segment. Several combinations of degree of polymerization and volume fraction of each block were investigated to access different self-assembled morphologies. Thin films of the sulfonated block copolymers were prepared by spin-coating and exposed to solvent vapor (SVA) or thermal annealing (TA) to reach equilibrium morphologies. Atomic force microscopy (AFM) was employed for characterizing the films, which exhibited a variety of nanometric equilibrium and nonequilibrium morphologies. Highly sulfonated samples revealed the formation of a honeycomb-like morphology obtained in solution rather than by the self-assembly of the BC in the solid state. The described morphologies may be employed in applications such as templates for nanomanufacturing and as cover and binder of catalytic particles in fuel cells.

Novel multiarm star block copolymer ionomers as proton conductive membranes

Novel multiarm star block copolymer ionomers containing hydrophobic fluorinated block at the periphery and partially sulfonated polystyrene block at the core with varying ion exchange capacities (IECs) were synthesized.