Tri-quaternized poly (ether sulfone) anion exchange membranes with improved hydroxide conductivity

Recent advancements in the synthesis of anion exchange membranes and their potential applications in wastewater treatment

Water treatment procedures are increasingly utilized for resource recovery and wastewater disinfection, addressing the current challenges of clean water depletion and wastewater management. Various pollutants, including dyes, acids, pharmaceuticals, and toxic heavy metals have been released into the environment through industrial, domestic, and agricultural activities, posing serious environmental and public health risks. Addressing these issues requires the development of more effective waste treatment processes. Membrane-based treatment technologies offer significant advantages, including high efficiency, versatility, and cost-effectiveness, making them a promising solution for mitigating the impact of these pollutants. In view of this, the potential of ion exchange membranes (IEMs) is continuously increasing due to their advanced characteristics compared to conventional techniques. Anion exchange membranes (AEMs), a special class of IEMs, selectively allow anions to pass through their pores due to the positive charge on their surface. This selective passage aids in resource recovery and removing specific types of pollutants. This review covers preparation methods, modification techniques, and classification of AEMs. It offers a practical classification based on the method of synthesis and structural properties of AEMs. The water-based applications of AEMs including, electrodialysis, diffusion dialysis, and electro-electrodialysis for various wastewater treatments such as heavy metal recovery, dye removal, pharmaceutical removal, and acid separation, have been discussed in detail. Additionally, the effect of various operational parameters on the performance and SWOT (strengths, weaknesses, opportunities, and threats) analysis of AEMs in effluent treatment are presented. The review provides detailed insights into the current status, challenges, and future directions of AEM-based technologies, offering suggestions for future advancements.

A Brief Review of Poly(Vinyl Alcohol)-Based Anion Exchange Membranes for Alkaline Fuel Cells

Anion exchange membrane fuel cells have unique advantages and are thus gaining increasing attention. Poly(vinyl alcohol) (PVA) is one of the potential polymers for the development of anion exchange membranes. This review provides recent studies on PVA-based membranes as alternative anion exchange membranes for alkaline fuel cells. The development of anion exchange membranes in general, including the types, materials, and preparation of anion exchange membranes in the last years, are discussed. The performances and characteristics of recently reported PVA-based membranes are highlighted, including hydroxide conductivity, water uptake, swelling degree, tensile strength, and fuel permeabilities. Finally, some challenging issues and perspectives for the future study of anion exchange membranes are discussed.

Removal of Metal Ions in Phosphoric Acid by Electro-Electrodialysis with Cross-Linked Anion-Exchange Membranes

There are numerous metallic impurities in wet phosphoric acid, which causes striking negative effects on industrial phosphoric acid production. In this study, the purification behavior of metallic impurities (Fe, Mg, Ca) from a wet phosphoric acid solution employing the electro-electrodialysis (EED) technology was investigated. The cross-linked polysulfone anion-exchange membranes (AEMs) for EED were prepared using N,N,N',N'-tetramethyl-1,6-hexanediamine (TMHDA) to achieve simultaneous cross-linking and quaternization without any cross-linkers or catalysts. The performance of the resulting membranes can be determined using quaternization reagents. When the molar ratio of trimethylamine/TMHDA/chloromethylated polysulfone is 3:1:1, the cross-linked membrane CQAPSU-3-1 exhibits lower water swelling and membrane area resistance than the non-cross-linked membrane. The low membrane area resistance of CQAPSU-3-1 with long alkyl chains is obtained due to the hydrophilic-hydrophobic microphase separation structure formed by TMHDA. EED experiments with different initial phosphoric acid concentrations of 0.52 and 1.07 M were conducted to evaluate the phosphoric acid purification of different AEMs. The results show that the EED experiments were more suitable for the purification of wet phosphoric acid solution at low concentrations. It was found that the phosphoric acid concentration in the anode compartment could be increased from 0.52 to 1.04 M. Through optimization, with an initial acid concentration of 0.52 M, CQAPSU-3-1 exhibits an enhanced metallic impurity removal ratio of higher than 72.0%, the current efficiency of more than 90%, and energy consumption of 0.48 kWh/kg. Therefore, CQAPSU-3-1 exhibits much higher purification efficiency than other membranes at a low initial phosphoric acid concentration, suggesting its potential in phosphoric acid purification application.

Radiation-Grafted Anion-Exchange Membrane for Fuel Cell and Electrolyzer Applications: A Mini Review

This review discusses the roles of anion exchange membrane (AEM) as a solid-state electrolyte in fuel cell and electrolyzer applications. It highlights the advancement of existing fabrication methods and emphasizes the importance of radiation grafting methods in improving the properties of AEM. The development of AEM has been focused on the improvement of its physicochemical properties, including ionic conductivity, ion exchange capacity, water uptake, swelling ratio, etc., and its thermo-mechano-chemical stability in high-pH and high-temperature conditions. Generally, the AEM radiation grafting processes are considered green synthesis because they are usually performed at room temperature and practically eliminated the use of catalysts and toxic solvents, yet the final products are homogeneous and high quality. The radiation grafting technique is capable of modifying the hydrophilic and hydrophobic domains to control the ionic properties of membrane as well as its water uptake and swelling ratio without scarifying its mechanical properties. Researchers also showed that the chemical stability of AEMs can be improved by grafting spacers onto base polymers. The effects of irradiation dose and dose rate on the performance of AEM were discussed. The long-term stability of membrane in alkaline solutions remains the main challenge to commercial use.

Anion Exchange Membranes Obtained from Poly(arylene ether sulfone) Block Copolymers Comprising Hydrophilic and Hydrophobic Segments

The anion exchange membrane may have different physical and chemical properties, electrochemical performance and mechanical stability depending upon the monomer structure, hydrophilicity and hydrophobic repeating unit, surface form and degree of substitution of functional groups. In current work, poly(arylene ether sulfone) (PAES) block copolymer was created and used as the main chain. After controlling the amount of NBS, the degree of bromination (DB) was changed in Br-PAES. Following that, quaternized PAES (Q-PAES) was synthesized through quaternization. Q-PAES showed a tendency of enhancing water content, expansion rate, ion exchange capacity (IEC) as the degree of substitution of functional groups increased. However, it was confirmed that tensile strength and dimensional properties of membrane reduced while swelling degree was increased. In addition, phase separation of membrane was identified by atomic force microscope (AFM) image, while ionic conductivity is greatly affected by phase separation. The Q-PAES membrane demonstrated a reasonable power output of around 64 mW/cm² while employed as electrolyte in fuel cell operation.

Hydrophilic Flexible Ether Containing, Cross-Linked Anion-Exchange Membrane Quaternized with DABCO

Anion-exchange membranes (AEM) with high ion content usually suffer from excessive water absorption and dilution effects that impair conductivity and mechanical properties. We herein report a novel ether containing a cross-linking strategy without adopting high ion-exchange capacity (IEC). The ether-containing cross-links and the quaternized structure are created simultaneously by introducing an ether-containing flexible hydrophilic spacer between two 1,4-diazabicyclo[2,2,2,2]octane or DABCO molecules; the resultant bi-DABCO structure was further employed to react with chloromethylated polysulfone. The long spacer with the ether moiety may benefit the hydroxide ion transport, and the cross-links will control the swelling and water absorption of the AEM. The two ether groups in the long spacer of the cross-links will also shield the DABCO cation from OH^- attack due to an electron-donating effect. The prepared membranes exhibited an improved conductivity of 31 mS/cm (at 25 °C) at a comparatively low IEC (1.08 mmol/g) with a rational water absorption and low swelling ratio (95.0 and 27.1%, respectively); they also displayed an enhanced alkaline stability in 1 M NaOH aqueous solution at 80 °C for 150 h. The density functional theory study and physical characterization after the alkaline treatment further confirm the better chemical stability of the cross-linked membrane over its counterpart. Our work presents an effective strategy to balance AEM conductivity and robustness.

Direct modification of polyketone resin for anion exchange membrane of alkaline fuel cells

A kind of side-chain type anion exchange membranes (AEMs) with high ionic conductivity and good comprehensive stability was prepared via direct modification of commercial engineering plastic polyketone with diamines through Paal-Knorr reaction and quaternization reaction. It was found that the amount of diamine can effectively tune the microphase morphology and properties of the prepared quaternized functionalized-polyketone anion exchange membranes (QAFPK-AEMs). The tensile strength was increased from 18.6 MPa to 38.6 MPa, and the ion exchange capacity (IEC) was increased from 1.11 mmol/g to 2.71 mmol/g depending on the amount of added diamine. The QAFPK-1-6-AEM with the IEC of 1.43 mmol/g showed the highest hydroxide conductivity of 65 mS/cm at 25 °C and 96.8 mS/cm at 80 °C. The high ionic conductivity was achieved through the establishment of effective ionic channels, and it maintained 70% of the initial ionic conductivity after the 192 h treatment in 2 mol/L KOH (aq) at 80 °C. Moreover, a peak power density of 129 mW/cm² was achieved when the assembled single cell with QAFPK-1-6-AEM was operated at 50 °C. Thus, the prepared QAFPK-AEMs showed great potential applications for the anion exchange membrane fuel cells (AEMFCs).

Highly Hydroxide-Conductive Nanostructured Solid Electrolyte via Predesigned Ionic Nanoaggregates

The creation of interconnected ionic nanoaggregates within solid electrolytes is a crucial yet challenging task for fabricating high-performance alkaline fuel cells. Herein, we present a facile and generic approach to embedding ionic nanoaggregates via predesigned hybrid core-shell nanoarchitecture within nonionic polymer membranes as follows: (i) synthesizing core-shell nanoparticles composed of SiO₂/densely quaternary ammonium-functionalized polystyrene. Because of the spatial confinement effect of the SiO₂ "core", the abundant hydroxide-conducting groups are locally aggregated in the functionalized polystyrene "shell", forming ionic nanoaggregates bearing intrinsic continuous ion channels; (ii) embedding these ionic nanoaggregates (20-70 wt %) into the polysulfone matrix to construct interconnected hydroxide-conducting channels. The chemical composition, physical morphology, amount, and distribution of the ionic nanoaggregates are facilely regulated, leading to highly connected ion channels with high effective ion mobility comparable to that of the state-of-the-art Nafion. The resulting membranes display strikingly high hydroxide conductivity (188.1 mS cm^-1 at 80 °C), which is one of the highest results to date. The membranes also exhibit good mechanical properties. The independent manipulation of the conduction function and nonconduction function by the ionic nanoaggregates and nonionic polymer matrix, respectively, opens a new avenue, free of microphase separation, for designing high-performance solid electrolytes for diverse application realms.

Imidazolium-functionalized anion exchange membranes using poly(ether sulfone)s as macrocrosslinkers for fuel cells

The incompatibility of the hydrophilic imidazolium cations from the functionalized poly(vinyl imidazole) with the long hydrophobic poly(ether sulfone) chain promoted the phase separation. The PES/PVIIL-0.4 membrane displayed good single cell performance.