Superhydrophobic membranes via facile bio-inspired mineralization for vacuum membrane distillation

Nanofilament-Coated Superhydrophobic Membranes Show Enhanced Flux and Fouling Resistance in Membrane Distillation

Membrane distillation (MD) is an important technique for brine desalination and wastewater treatment that may utilize waste or solar heat. To increase the distillation rate and minimize membrane wetting and fouling, we deposit a layer of polysiloxane nanofilaments on microporous membranes. In this way, composite membranes with multiscale pore sizes are created. The performance of these membranes in the air gap and direct contact membrane distillation was investigated in the presence of salt solutions, solutions containing bovine serum albumin, and solutions containing the surfactant sodium dodecyl sulfate. In comparison to conventional hydrophobic membranes, our multiscale porous membranes exhibit superior fouling resistance while attaining a higher distillation flux without using fluorinated compounds. This study demonstrates a viable method for optimizing MD processes for wastewater and saltwater treatment.

Nickel Chalcogenide Nanoparticles-Assisted Photothermal Solar Driven Membrane Distillation (PSDMD)

Developing photothermal solar driven membrane distillation (PSDMD) is of great importance in providing fresh water for remote off-grid regions. The production of freshwater through the PSDMD is driven by the temperature difference between feed and distillate sides created via the addition of efficient photothermal nanostructures. Here we proposed nickel sulfides and nickel tellurium nanoparticles (NPs) to be loaded into the polymeric membrane to enhance its performance. Ag and CuSe NPs are also considered for comparison as they are previously used for membrane distillation (MD). Our theoretical approach showed that all of the considered NPs increased the temperature of the PVDF membrane by around a few degrees. NiS and NiTe2 NPs are the most efficient solar light-to-heat converters compared to NiTe and NiS2 NPs due to their efficient absorption over the visible range. PVDF membrane loaded with 25% of NiCs NPs and a porosity of 32% produced a transmembrane vapor flux between 22 and 27 L/m²h under a 10-times-amplified sun intensity. Under the same conditions, the PVDF membrane loaded with CuSe and Ag NPs produced 15 and 18 L/m²h of vapor flux, respectively. The implantation of NPs through the membrane not only increased its surface temperature but also possessed a high porosity which provided a higher distillation and energy efficiency that reached 58% with NiS NPs. Finally, great agreement between our theoretical model and experimental measurement is obtained.

Study of MOF incorporated dual layer membrane with enhanced removal of ammonia and per-/poly-fluoroalkyl substances (PFAS) in landfill leachate treatment

Landfill leachate is a highly polluted and complex wastewater as it contains large amounts of organic matters, ammonia‑nitrogen, heavy metals, and per-/poly-fluoroalkyl substances (PFAS), which makes its treatment very challenging. In this paper, hydrophilic/hydrophobic dual layer membranes combining advantages of pervaporation and membrane distillation was employed to treat leachate in a direct contact membrane distillation (DCMD) configuration. An aluminum fumarate (AlFu) metal organic framework (MOF) incorporated poly(vinyl alcohol) (PVA) hydrophilic layer was coated on hydrophobic PTFE membrane to overcome the low separation efficiency of PFAS and ammonia and wetting issues encountered by the conventional hydrophobic PTFE membrane used for DCMD. The rejections of dual layer membranes with different MOF loading to PFAS, ammonia, TOC and TDS were assessed based on the amount of AlFu MOF incorporated into the PVA layer. Based on the conducted adsorption tests, it was found that AlFu MOF increases the rejection of PVA layer to PFAS and ammonia. The coating of the hydrophilic layer could enhance the wetting resistance with/without MOF addition. In comparison with the pristine PTFE membrane using synthetic feed containing 3 wt% NaCl, 1 wt% addition of AlFu MOF into the PVA layer showed slightly increased flux. All the tested membranes showed more than 99% rejection to TOC. The rejection to ammonia was increased as more MOF was incorporated into the PVA layer. The maximum rejection of ammonia was 99.8% when the PVA layer containing 10% MOF. All the membranes showed more than 99% rejection to PFOS and PFHxS. However, PTFE membrane did not show any rejection to PFOA. As more MOF was added into the hydrophilic layer, the rejection to PFOA increased, but plateaued at 65.6% with 5% MOF incorporation into the hydrophilic layer.

Effective separation of water-DMSO through solvent resistant membrane distillation (SR-MD)

The treatment of organic waste or wastewater with high organic solvent content has been challenging in industries as it cannot be done effectively using conventional wastewater treatment technologies such as biodegradation and advanced oxidation process. Solvent resistant membrane distillation (SR-MD) was proposed as an energy-efficient alternative to treat these waste streams but its application is hampered by the lack of solvent-resistant membranes, and there is a research gap in studying the feeds with water-solvent mixtures. In this work, ceramic tubular membranes with different pore sizes and structures were molecularly grafted with 1H,1H,2H,2H-perfluorodecyltriethoxysilane to obtain hydrophobic ceramic membranes for SR-MD. The modified membranes exhibited excellent hydrophobicity and solvent resistant properties, and they were tested for SR-MD performance with a wide range of dimethyl sulfoxide (DMSO) feed concentrations, from 3.5 to 85 wt%. The membranes exhibited a high DMSO rejection of >98% and the separation factor of >170, with permeation flux >4.4 kg m^-2 h^-1 when the DMSO concentration in feed was below 65 wt%. The separation performance was found strongly dependent on the evaporation step and the vapour-liquid equilibrium near the interface. The DMSO rejection was also comparable to pervaporation while the permeation flux was much higher at the feed concentration of 50 wt%. This study establishes the strategy of using SR-MD as a promising membrane process in treating complex industrial wastes with high organic solvent content.

A Critical Review of Membrane Wettability in Membrane Distillation from the Perspective of Interfacial Interactions

Hydrophobic membranes used in membrane distillation (MD) systems are often subject to wetting during long-term operation. Thus, it is of great importance to fully understand factors that influence the wettability of hydrophobic membranes and their impact on the overall separation efficiency that can be achieved in MD systems. This Critical Review summarizes both fundamental and applied aspects of membrane wetting with particular emphasis on interfacial interaction between the membrane and solutes in the feed solution. First, the theoretical background of surface wetting, including the relationship between wettability and interfacial interaction, definition and measurement of contact angle, surface tension, surface free energy, adhesion force, and liquid entry pressure, is described. Second, the nature of wettability, membrane wetting mechanisms, influence of membrane properties, feed characteristics and operating conditions on membrane wetting, and evolution of membrane wetting are reviewed in the context of an MD process. Third, specific membrane features that increase resistance to wetting (e.g., superhydrophobic, omniphobic, and Janus membranes) are discussed briefly followed by the comparison of various cleaning approaches to restore membrane hydrophobicity. Finally, challenges with the prevention of membrane wetting are summarized, and future work is proposed to improve the use of MD technology in a variety of applications.

Superhydrophobic surface coating on electrospun polypropylene membrane to treat high salinity water in membrane distillation

Membrane distillation (MD) is an advantageous separation process compared with pressure-driven technologies and was subsequently introduced to treat aquaculture wastewater. Harnessing a superhydrophobic membrane in an MD process is of extreme importance to prevent membrane wetting. In this work, the electrospun polypropylene (PP) membrane was surface modified by depositing an additional coating of PP via the solvent-exchange method, thereby improving the membrane's superhydrophobicity. Layer-by-layer deposition of PP caused the formation of uniform polymer spherulites on the membrane surface, which levelled up the membrane's surface roughness. A superhydrophobic surface was achieved by applying a single-layered PP coating, with static water contact angle of 152.2° and sliding angle of 12.5°. While all membranes achieved almost perfect salt rejection (up to 99.99%), the MD permeate flux improved by 30%, average of 13.0 kg/m²h, when the single-layered PP-coated membrane was used to treat the high salinity water in both 2 and 60 hr MD processes. Further layers of coating resulted in larger size of PP spherulites with higher sliding angle, followed by lowered flux in MD. The evenness of the surface coating and the size of the aggregate PP spherulites (nano-scaled) are two predominant factors contributing to the superhydrophobicity character of a membrane.

A few-layer graphene for advanced composite PVDF membranes dedicated to water desalination: a comparative study

Membrane distillation is envisaged to be a promising best practice to recover freshwater from seawater with the prospect of building low energy-consuming devices powered by natural and renewable energy sources in remote and less accessible areas. Moreover, there is an additional benefit of integrating this green technology with other well-established operations dedicated to desalination. Today, the development of membrane distillation depends on the productivity-efficiency ratio on a large scale. Despite hydrophobic commercial membranes being widely used, no membrane with suitable morphological and chemical feature is readily available in the market. Thus, there is a real need to identify best practices for developing new efficient membranes for more productive and eco-sustainable membrane distillation devices. Here, we propose engineered few-layer graphene membranes, showing enhanced trans-membrane fluxes and total barrier action against NaCl ions. The obtained performances are linked with filling polymeric membranes with few-layer graphene of 490 nm in lateral size, produced by the wet-jet milling technology. The experimental evidence, together with comparative analyses, confirmed that the use of more largely sized few-layer graphene leads to superior productivity related efficiency trade-off for the membrane distillation process. Herein, it was demonstrated that the quality of exfoliation is a crucial factor for addressing the few-layer graphene supporting the separation capability of the host membranes designed for water desalination.

Wetting phenomena in membrane distillation: Mechanisms, reversal, and prevention

Membrane distillation (MD) is a rapidly emerging water treatment technology; however, membrane pore wetting is a primary barrier to widespread industrial use of MD. The primary causes of membrane wetting are exceedance of liquid entry pressure and membrane fouling. Developments in membrane design and the use of pretreatment have provided significant advancement toward wetting prevention in membrane distillation, but further progress is needed. In this study, a broad review is carried out on wetting incidence in membrane distillation processes. Based on this perspective, the study describes the wetting mechanisms, wetting causes, and wetting detection methods, as well as hydrophobicity measurements of MD membranes. This review discusses current understanding and areas for future investigation on the influence of operating conditions, MD configuration, and membrane non-wettability characteristics on wetting phenomena. Additionally, the review highlights mathematical wetting models and several approaches to wetting control, such as membrane fabrication and modification, as well as techniques for membrane restoration in MD. The literature shows that inorganic scaling and organic fouling are the main causes of membrane wetting. The regeneration of wetting MD membranes is found to be challenging and the obtained results are usually not favorable. Several pretreatment processes are found to inhibit membrane wetting by removing the wetting agents from the feed solution. Various advanced membrane designs are considered to bring membrane surface non-wettability to the states of superhydrophobicity and superomniphobicity; however, these methods commonly demand complex fabrication processes or high-specialized equipment. Recharging air in the feed to maintain protective air layers on the membrane surface has proven to be very effective to prevent wetting, but such techniques are immature and in need of significant research on design, optimization, and pilot-scale studies.