pH and thermal-dependent ultrafiltration membranes prepared from poly (methacrylic acid) grafted onto polyethersulfone synthesized by simultaneous irradiation in homogenous phase

A PEGylated PVDF Antifouling Membrane Prepared by Grafting of Methoxypolyethylene Glycol Acrylate in Gama-Irradiated Homogeneous Solution

In this study, methoxypolyethylene glycol acrylate (mPEGA) served as a PEGylated monomer and was grafted onto polyvinylidene fluoride (PVDF) through homogeneous solution gamma irradiation. The grafting process was confirmed using several techniques, including infrared spectroscopy (FTIR), thermodynamic stability assessments, and rotational viscosity measurements. The degree of grafting (DG) was determined via the gravimetric method. By varying the monomer concentration, a range of DGs was achieved in the PVDF-g-mPEGA copolymers. Investigations into water contact angles and scanning electron microscopy (SEM) images indicated a direct correlation between increased hydrophilicity, membrane porosity, and higher DG levels in the PVDF-g-mPEGA membrane. Filtration tests demonstrated that enhanced DGs resulted in more permeable PVDF-g-mPEGA membranes, eliminating the need for pore-forming agents. Antifouling tests revealed that membranes with a lower DG maintained a high flux recovery rate, indicating that the innate properties of PVDF could be largely preserved.

Anti-fouling and protein separation of PVDF-g-PMAA@MnO2 filtration membrane with in-situ grown MnO2 nanorods

MnO₂ nanorods with controllable scale were grown in the PVDF-g-PMAA modified membrane to form PVDF-g-PMAA@ MnO₂ membrane through the in situ redox reaction of KMnO₄ solution, which is confirmed by scanning electron microscopy (SEM) and X-ray energy-dispersion spectroscopy (EDX). The pore size of the membrane decreased with the increase of KMnO₄ solution concentration. The thermodynamic stability and the hydrophilicity of the membrane were also enhanced by the MnO₂ nanorods. The water flux, bovine serum albumin (BSA)/Lysozyme protein solution flux and rejection, flux recovery, etc. showed effective improvement of the anti-fouling performance of the PVDF-g-PMAA@ MnO₂ membrane. More importantly, it can effectively separate BSA from lysozyme, which provided a potential application in the field of biology, food, and other industrial fields for the requirement of separation and purification.

Antifouling Membranes Prepared from Polyethersulfone Grafted with Poly(ethylene glycol) Methacrylate by Radiation-Induced Copolymerization in Homogeneous Solution

To synthesize evenly grafted copolymers, gamma radiation of homogeneous solutions was employed to graft poly(ethylene glycol) methacrylate (PEGMA) onto polyethersulfone (PES). The grafting was verified by Fourier transform infrared spectroscopy, and the degrees of grafting (DGs) were determined by elementary analysis. The PES-g-polyPEGMA copolymers with different DGs were obtained by changing the monomer concentration. Membranes were cast from pristine PES, PES/PEG blends, and PES-g-polyPEGMA with different DGs, respectively, via nonsolvent-induced phase separation. Results from water contact angle measurements and scanning electron microscopy analysis indicated that increasing DGs led to PES-g-polyPEGMA membranes with increasing hydrophilicity and porousness. Filtration experimental results showed that increasing DGs without adding pore-forming agents caused PES-g-polyPEGMA membranes with higher permeability. Compared with PES/PEG membranes with analogous permeation characteristics, in which PEG is added as a pore-forming agent, PES-g-polyPEGMA membranes exhibited superior antifouling properties.

Zwitterionic Membrane via Nonsolvent Induced Phase Separation: A Computer Simulation Study

Dissipative particle dynamics (DPD) was adopted to study the nonsolvent induced phase separation (NIPS) process during a pH-responsive poly(ether sulfone) membrane preparation with a zwitterionic copolymer poly(ether sulfone)- block-polycarboxybetaine methacrylate (PES-b-PCBMA) as the blending additive. The membrane formation process and final morphology were analyzed. Simulation results show that the hydrophilic PCBMA segments enrich on the membrane surface by surface segregation and exhibit pH-responsive behavior, which is attributed to the deprotonation of the carboxylic acid group. With the polymer concentration increasing, both the shrinkage of the membrane and the flexibility of the system decrease, which also reduce the effect of surface segregation. By adjusting the blend ratio of PES-b-PCBMA with PES from 5% to 15%, the surface coverage of PCBMA segments on the membrane can be regulated. This work contributes to a better understanding on the mechanism of NIPS and can serve as a guide for the design of the polymer blend membrane.

pH-sensitive microfiltration membrane prepared from polyethersulfone grafted with poly(itaconic acid) synthesized by simultaneous irradiation in homogeneous phase

Poly(itaconic acid) (PIA) was grafted onto polyethersulfone (PES) by homogeneously phased γ-ray irradiation. Kinetic polymerization observed was studied by analyzing the effect of irradiation dosages and monomer concentrations. Then, a pH-sensitive microfiltration (MF) membrane was prepared from these PES-g-PIA polymers with different degrees of grafting under phase inversion method. Finally, the contact angles, morphologies, pore sizes, deionized water permeability and filtration performance for aqueous polyethylene glycols solution of the MF membranes were studied. The results show that grafting PIA groups onto PES molecular chains endowed the MF membranes with effective pH-sensitive properties.